The first generation of “GPH Single Shear Off Technology” allowed precision and consistent contact force with which the conductor is installed into the barrel of the mechanical connector providing:
• a simple and fail safe solution without use of special tools
• a connection that guaranteed the correct contact force within the barrel by shearing off the hexagon head at the correct torque level every time
• optimized contact regardless of the cable type or make-up e.g. solid, stranded, compacted, round or sector
• suitability for a wide cross sectional range of conductors
The second generation of “GPH Double Shear Off Technology” using an Allen Key for a 2 Step installation providing suitability for a wider cross sectional range of conductors. Further development for medium voltage applications required reduction of “excess length” of shear off bolts.
The third generation of “GPH Multi Share Off Bolt Technology” once again improved the technical performance. This design was patented in 1998 and is used in all GPH M- and C - Series products. Market demand, to reduce stock cost, drove the need to widen the cross section range. This brought new challenges into the design of mechanical connectors when considering the minimum and maximum range of a particular shear bolt and the management of excess length of the shear bolt itself. It is physically intuitive that small cross sections should be connected with lower forces than larger ones. Exposing small conductors to high contact forces causes inevitable partial cross section reduction.
Förderfähige Wallbox zum eleganten Einbau im Innen- und Aussenbereich von Gebäuden, Garagen und Wohnanlagen mit der Option des Lastmanagements und vielen Smart Home Kompatibilitäten. Skalierbare Aufladung von Elektrofahrzeugen auch im zeitversetzten Betrieb mit Messzähl-Einrichtung und Abrechnungsverfahren. Zur Aufladung von E-Autos mit Typ2 Anschlusskabel.
Katalog Megger Messgeräte für Niederspannungsnetze 2017e-Marke Österreich
Installationstester nach ÖVE E 8001 und 8701
Isolations, Erdungs- und Schleifenwiderstandsmessung
Multimeter, Spannungsprüfer, Ortungsgeräte, Niederohmmessgeräte und Zeitbereichsreflektometer
The OPERATOR is a power bar for up to 8 resp. 12 devices, ensuring a new and hitherto unrivaled quality of full speed processing of current pulses, thanks to the SCHNERZINGER ATOMIC BONDING formatting processes.
The quality of the supply cable used could again be improved by consistent further development and optimized adaptation to the newly developed SCHNERZINGER cable lines.
Available at
www.falkenstein-proaudio.shop
More infos
www.schnerzinger.com
SW-Benutzerhandbuch und Onlinehilfe aus einer QuelleRainer Pflaum
Anforderungen an Technische Dokumentation, SW-Benutzerhandbücher, Onlinehilfe, JPG-Problem, Texterstellung, Warnhinweise nach ANSII Z 535.6, Redaktionssysteme, ST4, TIM-RS, Direkteinsprung in PDF-Dateien
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
The first generation of “GPH Single Shear Off Technology” allowed precision and consistent contact force with which the conductor is installed into the barrel of the mechanical connector providing:
• a simple and fail safe solution without use of special tools
• a connection that guaranteed the correct contact force within the barrel by shearing off the hexagon head at the correct torque level every time
• optimized contact regardless of the cable type or make-up e.g. solid, stranded, compacted, round or sector
• suitability for a wide cross sectional range of conductors
The second generation of “GPH Double Shear Off Technology” using an Allen Key for a 2 Step installation providing suitability for a wider cross sectional range of conductors. Further development for medium voltage applications required reduction of “excess length” of shear off bolts.
The third generation of “GPH Multi Share Off Bolt Technology” once again improved the technical performance. This design was patented in 1998 and is used in all GPH M- and C - Series products. Market demand, to reduce stock cost, drove the need to widen the cross section range. This brought new challenges into the design of mechanical connectors when considering the minimum and maximum range of a particular shear bolt and the management of excess length of the shear bolt itself. It is physically intuitive that small cross sections should be connected with lower forces than larger ones. Exposing small conductors to high contact forces causes inevitable partial cross section reduction.
Förderfähige Wallbox zum eleganten Einbau im Innen- und Aussenbereich von Gebäuden, Garagen und Wohnanlagen mit der Option des Lastmanagements und vielen Smart Home Kompatibilitäten. Skalierbare Aufladung von Elektrofahrzeugen auch im zeitversetzten Betrieb mit Messzähl-Einrichtung und Abrechnungsverfahren. Zur Aufladung von E-Autos mit Typ2 Anschlusskabel.
Katalog Megger Messgeräte für Niederspannungsnetze 2017e-Marke Österreich
Installationstester nach ÖVE E 8001 und 8701
Isolations, Erdungs- und Schleifenwiderstandsmessung
Multimeter, Spannungsprüfer, Ortungsgeräte, Niederohmmessgeräte und Zeitbereichsreflektometer
The OPERATOR is a power bar for up to 8 resp. 12 devices, ensuring a new and hitherto unrivaled quality of full speed processing of current pulses, thanks to the SCHNERZINGER ATOMIC BONDING formatting processes.
The quality of the supply cable used could again be improved by consistent further development and optimized adaptation to the newly developed SCHNERZINGER cable lines.
Available at
www.falkenstein-proaudio.shop
More infos
www.schnerzinger.com
SW-Benutzerhandbuch und Onlinehilfe aus einer QuelleRainer Pflaum
Anforderungen an Technische Dokumentation, SW-Benutzerhandbücher, Onlinehilfe, JPG-Problem, Texterstellung, Warnhinweise nach ANSII Z 535.6, Redaktionssysteme, ST4, TIM-RS, Direkteinsprung in PDF-Dateien
Isolation Procedures for Safe Working on Electrical Systems and Equipment by the JIB | solation Procedures for Safe Working on Electrical Systems and Equipment
This chart shows the safe isolation procedure that you should use when working on electrical systems and equipment.
You'll receive a printed copy of this from your Training Provider, but it's also here as a handy reference to keep electronically.
THE RULES OF SAFE ISOLATION ARE:
Obtain permission to start work (a Permit may be required in some situations)
Identify the source(s) of supply using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Isolate the supply(s)
Secure the isolation
Prove the system/equipment is DEAD using an approved voltage indicator or test lamp
Prove that the approved voltage indicator or test lamp is functioning correctly
Put up warning signs to tell other people that the electrical installation has been isolated
Once the system/equipment is proved DEAD, work can begin
Uploaded by THORNE & DERRICK LV HV Jointing, Earthing, Substation & Electrical Eqpt | Explosive Atmosphere Experts & ATEX IECEx.
THORNE & DERRICK based in the UK are international distributors of LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment.
Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.
Contact us for 3M, ABB, Alroc, AN Wallis, CATU, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.
Filoform FiloSeal+HD Reenterable LV HV Power Cable Duct Seal System - Spec Sheet
MC4 Multi Contact Solar Connector
1. Advanced Contact Technology
14 www.multi-contact.com
PV-KST4...
PV-KBT4...
MA
Ich
bin
eine
Montageanleitung.
Man
sollte
mich unbedingt
le-
sen,
bevor
man das Produkt
ver-
wendet!
Ich beinhalte wertvoll
e
Hinweise
zur korrekten Montag
e
und
zum richtigen
Einsatz
des
Produktes.
Im Moment
ist
die
Schrift
zwar ein bischen
klein,
aber
später
geht das dann
ganz
gut
zu
lesen,
da die MA dann
Montageanleitung MA231
www.multi-contact.com
Sicherungshülse Seite 47
Verschlusskappen Seite 49
Montageschlüsselset Seite 55
Kupplungsbuchsen und -stecker als Einzelteil
(inklusive Isolierteil)
MA
Ich
bin
eine
Montageanleitung.
Man
sollte
mich unbedingt
le-
sen,
bevor
man das Produkt
ver-
wendet!
Ich beinhalte wertvoll
e
Hinweise
zur korrekten Montag
e
und
zum richtigen
Einsatz
des
Produktes.
Im Moment
ist
die
Schrift
zwar ein bischen
klein,
aber
später
geht das dann
ganz
gut
zu
lesen,
da die MA dann
Assembly Instructions MA231
www.multi-contact.com
Safety lock clip page 47
Sealing caps page 49
Assembly tools page 55
Female and male cable coupler as individual part
(including insulating part)
Kupplungsbuchse, -stecker
MC4
Female and male cable coupler
MC4
Typ
Type
Bestell-Nr.
OrderNo.
Kupplungsbuchse
Femalecablecoupler
Kupplungsstecker
Malecablecoupler
Ø-BereichKabelverschraubung
Ørangeofcablegland
Leiterquerschnitt
Conductorcrosssection
Zulassungen
Approvals
A (mm) mm² AWG b (mm)
PV-KBT4/2,5I-UR 32.0010P0001-UR × 3 – 6 1,5; 2,5 14 3 ⎫
⎪
⎪
⎪
⎪
⎪
⎬
⎪
⎪
⎪
⎪
⎪
⎭
PV-KST4/2,5I-UR 32.0011P0001-UR × 3 – 6 1,5; 2,5 14 3
PV-KBT4/2,5II-UR 32.0012P0001-UR × 5,5 – 9 1,5; 2,5 14 3
PV-KST4/2,5II-UR 32.0013P0001-UR × 5,5 – 9 1,5; 2,5 14 3
PV-KBT4/6I-UR 32.0014P0001-UR × 3 – 6 4; 6 12; 10 5
PV-KST4/6I-UR 32.0015P0001-UR × 3 – 6 4; 6 12; 10 5
PV-KBT4/6II-UR 32.0016P0001-UR × 5,5 – 9 4; 6 12; 10 5
PV-KST4/6II-UR 32.0017P0001-UR × 5,5 – 9 4; 6 12; 10 5
PV-KBT4/10II 32.0034P0001 × 5,5 – 9 10 – 7,2 ⎫
⎬
⎭PV-KST4/10II 32.0035P0001 × 5,5 – 9 10 – 7,2
2. Advanced Contact Technology
www.multi-contact.com 15
■■ Snap-In Verriegelung
■■ Durch Einsatz der Sicherungshülse PV-SSH4 Verriegelung
nach NEC 2011, nur mit Werkzeug entriegelbar
■■ Bewährte, langzeitstabile MULTILAM Technologie, dadurch
konstant geringe Verlustleistung über die gesamte Lebens-
dauer der Steckverbinder
■■ Bewährter Steckverbinder, 12 Jahre Felderfahrung
■■ Auch für Querschnitte von 10 mm² konfektionierbar
■■ Auch erhältlich als konfektionierte Leitungen, siehe Seite 60
■■ Leitungen nach Kundenwunsch, siehe Seite 62
1)
2Pfg2330: Nur für zugangsbeschränkte Standorte zugelassen
■■ Snap-in lock
■■ Locking by safety lock clip PV-SSH4 in accordance with
NEC 2011, can be released only with tool
■■ Proven MULTILAM technology with high long-term stability,
which ensures consistently low performance loss throughout
the entire service life of the plug connector
■■ Tried and tested plug connectors, 12 years of experience in
the field
■■ Available for assembly with cross-sections of 10 mm²
■■ Also available as ready made leads, see page 60
■■ Leads made to customer’s specifications, see page 62
1)
2Pfg2330: only approved for locations with restricted access
Technische Daten Technical data
Steckverbindersystem Connector system Ø 4 mm
Bemessungsspannung Rated voltage
1000 V DC / 1500 V DC (IEC)1)
1000 V DC / 600 V DC (UL)
Bemessungsstrom IEC (90 °C) Rated current IEC (90 °C)
17 A (1,5 mm²)
22,5 A (2,5 mm²; 14 AWG)
30 A (4 mm², 6 mm²; 12 AWG, 10 AWG)
43 A (10 mm²)
Bemessungsstrom IEC (85 °C) Rated current IEC (85 °C)
17 A (1,5 mm²)
22,5 A (2,5 mm²; 14 AWG)
39 A (4 mm²; 12 AWG)
45 A (6 mm²; 10 AWG)
Bemessungsstoßspannung Rated impulse voltage
12 kV (1000 V DC (IEC))
16 kV (1500 V DC (IEC))
Umgebungstemperaturbereich Ambient temperature range
-40 °C...+90 °C (IEC)
-40 °C...+75 °C (UL)
-40 °C...+70 °C (UL: 14 AWG)
Obere Grenztemperatur Upper limiting temperature 105 °C (IEC)
Schutzart, gesteckt
ungesteckt
Degree of protection, mated
unmated
IP65, IP68 (1 h / 1 m)
IP2X
Überspannungskat. / Verschmutzungsgrad Overvoltage category / Pollution degree CATIII / 3
Kontaktwiderstand der Steckverbinder Contact resistance of plug connectors ≤ 0,35 mΩ
Schutzklasse Safety class
1000 V DC: II
1500 V DC: 0
Kontaktsystem Contact system MULTILAM
Anschlussart Type of termination Crimpen / Crimping
Kontaktmaterial Contact material Kupfer, verzinnt / Copper, tin plated
Isolationsmaterial Insulation material PC / PA
Verriegelungssystem (UL) Locking system (UL) Locking type
Flammklasse Flame class UL94-V0
Ammoniakbeständigkeit (gemäß DLG) Ammonia resistance (acc. to DLG) 1500 h, 70 °C / 70 % RH, 750 ppm
Salznebelsprühtest, Schärfegrad 6 Salt mist spray test, degree of severity 6 IEC 60068-2-52
TÜV-Rheinland zertifiziert nach EN 50521
TÜV-Rheinland zertifiziert nach 2PfG2330
UL anerkannte Komponente nach UL 6703
CSA zertifiziert nach UL 6703
TÜV-Rheinland certified, in accordance with EN 50521
TÜV-Rheinland certified, in accordance with 2PfG2330
UL recognized component, in accordance with UL 6703
CSA certified, in accordance with UL 6703
R60028286
R60087448
E343181
250725