The document provides information about Dodge Quantis reducers and gearmotors that can be assembled at the Menden build center in Germany. It includes selection guides and part numbers for inline helical (ILH), right angle helical bevel (RHB), and motorized shaft mount (MSM) product configurations. Variant codes are listed to specify required instructions and options for build center quotes and orders.
The document discusses certificates that can be provided with Lönne electric motors. It describes four types of certificates according to EN 10204: Type 2.1 is a declaration of compliance, Type 2.2 is a test report with non-specific inspection results, Type 3.1 is an inspection certificate issued by the manufacturer with test results, and Type 3.2 is an inspection certificate prepared by both the manufacturer and purchaser representatives with test results. It also states that motors will be tested in the company's test field or an external institute, and that marine classification bureaus provide type approval certificates.
This document provides technical specifications and performance data for a line of hydraulic motors and brakes. It includes charts showing torque, speed, pressure and flow ratings. It also provides guidelines for installation, operation, and circuit design. Safety precautions are outlined for proper use of motors, brakes and motor/brake combinations. Dimensional drawings and ordering information are provided for different motor series and models.
This document provides information on ABB's BSM N-series AC servo motors, including:
- The BSM N-series provides low inertia and high torque for excellent dynamic performance and high machine throughput.
- Motors are available in sizes from 50mm to 100mm frame sizes with continuous torques ranging from 3.9 lb-in to 354 lb-in.
- Performance curves and specifications are provided for various motor models.
Электродвигатели постоянного тока Bonfiglioli BCArve
The document provides specifications for Bonfiglioli permanent magnet DC motors that are suitable for operating in temperatures ranging from -20°C to +40°C. It discusses factors that affect motor power output, including duty cycle, speed, supply form factor, temperature, and altitude. Dimensional variations are shown for motors fitted with brakes. Technical specifications like voltage, speed, power, torque, current, and moment of inertia are given for different motor types and sizes.
The document contains a series of check marks and symbols with no clear context or meaning. It is not possible to determine what the document is about or summarize its content in 3 sentences or less due to the lack of coherent information.
This document provides assembly and operating instructions for planetary gear units. It begins with an introduction and covers technical data, supply conditions, packing/handling, installation, lubrication, checks, maintenance, scrap disposal, oil plug positions, weight/oil quantities, and multi-disc brakes. The instructions provide details on receiving, storing, installing flange, foot and shaft-mounted gear units. It emphasizes ensuring proper lubrication and maintenance for safe and efficient operation.
Die Drehfutter und Planscheiben aus dem Hause RÖHM kommen sowohl für rotierende, als auch für stationäre Bearbeitung von Werkstücken auf Dreh- und Schleifmaschinen zum Einsatz. Auch können mit Ihnen Mess- und Kontrollarbeiten durchgeführt werden.
Mit den RÖHM Drehfuttern und Planscheiben können asymmetrische Werkstücke, sowie Flansche, Rohre, Scheiben und Stangen bearbeitet werden. Dabei kann das Spannen von sehr langen Werkstücken ggf. zusätzliche Spannmittel wie Lünetten oder Spitzen erfordern.
Keilstangenfutter
Die RÖHM Keilstangenfutter tragen ihren Namen aufgrund der drei Keilstangen in ihrem Inneren, welche für die Verschiebung der Backen sorgen. Sie glänzen durch eine extrem hohe Spanngenauigkeit, hohe Spannkräfte, eine hohe Rundlaufgenauigkeit sowie eine verlässliche Dauerwiederholgenauigkeit. Die Dreibacken-Stahlfutter spannen zentrisch und sind speziell für Schleifmaschinen geeignet. Sie verfügen über einen zentralen Kraftantrieb, erlauben einen schnellen Backenwechsel und sind zentrisch spannend.
Weitere Merkmale sind:
- Backensicherung
- Abdeckung speziell für Schleifmaschinen
Drehfutter mit Spiralring
Planspiralfutter
RÖHM Planspiralfutter werden manuell betätigt, mittels Schlüssel mit Knebel welcher eine Spirale im Inneren des Futters antreibt. Dieser spannt die Backen. Sie verfügen über eine flache Bauweise, die Anschlussmaße richten sich nach DIN-Normen. Mit ihnen ist ein Durchfahren des gesamten Spannbereichs möglich.
RÖHM Planspiralfutter sind eine sehr preiswertes Spannmittel, jedoch ist die Spannkraft bei gleichem eingeleitetem Drehmoment geringer als beim Keilstangenfutter.
Planspiralfutter von RÖHM sind jeweils mit drei oder vier Backen verfügbar, dabei gibt es folgende Varianten:
Dreh- und Schleiffutter
ZG Hi-Tru:
- Radiale Feineinstellung für höchste
Rundlaufgenauigkeit
- Rundlauf auf unter 0,005 mm einstellbar
- Wiederholspanngenauigkeit 0,015 mm
- Gusskörper
- Feineinstellung ohne Lösen der Befestigungsschrauben
- Stahlaufnahmeflansch
- Auch als abgedichtete Variante
Kranzspannfutter
KRF:
- Drei- und Vierbackenfutter
- Gusskörper
- Positionieren und Befördern von ringförmigen Werkstücken
- Größen 125 bis 200: 4 Gewindestifte für Feineinstellung
- Mit und ohne Grundplatte
- Zylindrische Zentrieraufnahme
Planscheiben
RÖHM Planscheiben, bei welchen es sich um ein Vierbackenfutter mit Durchgang handelt, werden zur Einzelspannung eingesetzt. Sie sind besonders gut für die Spannung asymmetrischer Werkstücke sowie für die Längs- oder Planbearbeitung geeignet.
http://eshop.roehm.biz/roehm_de_de/online-shop/drehfutter-planscheiben.html
The document provides information about Dodge Quantis reducers and gearmotors that can be assembled at the Menden build center in Germany. It includes selection guides and part numbers for inline helical (ILH), right angle helical bevel (RHB), and motorized shaft mount (MSM) product configurations. Variant codes are listed to specify required instructions and options for build center quotes and orders.
The document discusses certificates that can be provided with Lönne electric motors. It describes four types of certificates according to EN 10204: Type 2.1 is a declaration of compliance, Type 2.2 is a test report with non-specific inspection results, Type 3.1 is an inspection certificate issued by the manufacturer with test results, and Type 3.2 is an inspection certificate prepared by both the manufacturer and purchaser representatives with test results. It also states that motors will be tested in the company's test field or an external institute, and that marine classification bureaus provide type approval certificates.
This document provides technical specifications and performance data for a line of hydraulic motors and brakes. It includes charts showing torque, speed, pressure and flow ratings. It also provides guidelines for installation, operation, and circuit design. Safety precautions are outlined for proper use of motors, brakes and motor/brake combinations. Dimensional drawings and ordering information are provided for different motor series and models.
This document provides information on ABB's BSM N-series AC servo motors, including:
- The BSM N-series provides low inertia and high torque for excellent dynamic performance and high machine throughput.
- Motors are available in sizes from 50mm to 100mm frame sizes with continuous torques ranging from 3.9 lb-in to 354 lb-in.
- Performance curves and specifications are provided for various motor models.
Электродвигатели постоянного тока Bonfiglioli BCArve
The document provides specifications for Bonfiglioli permanent magnet DC motors that are suitable for operating in temperatures ranging from -20°C to +40°C. It discusses factors that affect motor power output, including duty cycle, speed, supply form factor, temperature, and altitude. Dimensional variations are shown for motors fitted with brakes. Technical specifications like voltage, speed, power, torque, current, and moment of inertia are given for different motor types and sizes.
The document contains a series of check marks and symbols with no clear context or meaning. It is not possible to determine what the document is about or summarize its content in 3 sentences or less due to the lack of coherent information.
This document provides assembly and operating instructions for planetary gear units. It begins with an introduction and covers technical data, supply conditions, packing/handling, installation, lubrication, checks, maintenance, scrap disposal, oil plug positions, weight/oil quantities, and multi-disc brakes. The instructions provide details on receiving, storing, installing flange, foot and shaft-mounted gear units. It emphasizes ensuring proper lubrication and maintenance for safe and efficient operation.
Die Drehfutter und Planscheiben aus dem Hause RÖHM kommen sowohl für rotierende, als auch für stationäre Bearbeitung von Werkstücken auf Dreh- und Schleifmaschinen zum Einsatz. Auch können mit Ihnen Mess- und Kontrollarbeiten durchgeführt werden.
Mit den RÖHM Drehfuttern und Planscheiben können asymmetrische Werkstücke, sowie Flansche, Rohre, Scheiben und Stangen bearbeitet werden. Dabei kann das Spannen von sehr langen Werkstücken ggf. zusätzliche Spannmittel wie Lünetten oder Spitzen erfordern.
Keilstangenfutter
Die RÖHM Keilstangenfutter tragen ihren Namen aufgrund der drei Keilstangen in ihrem Inneren, welche für die Verschiebung der Backen sorgen. Sie glänzen durch eine extrem hohe Spanngenauigkeit, hohe Spannkräfte, eine hohe Rundlaufgenauigkeit sowie eine verlässliche Dauerwiederholgenauigkeit. Die Dreibacken-Stahlfutter spannen zentrisch und sind speziell für Schleifmaschinen geeignet. Sie verfügen über einen zentralen Kraftantrieb, erlauben einen schnellen Backenwechsel und sind zentrisch spannend.
Weitere Merkmale sind:
- Backensicherung
- Abdeckung speziell für Schleifmaschinen
Drehfutter mit Spiralring
Planspiralfutter
RÖHM Planspiralfutter werden manuell betätigt, mittels Schlüssel mit Knebel welcher eine Spirale im Inneren des Futters antreibt. Dieser spannt die Backen. Sie verfügen über eine flache Bauweise, die Anschlussmaße richten sich nach DIN-Normen. Mit ihnen ist ein Durchfahren des gesamten Spannbereichs möglich.
RÖHM Planspiralfutter sind eine sehr preiswertes Spannmittel, jedoch ist die Spannkraft bei gleichem eingeleitetem Drehmoment geringer als beim Keilstangenfutter.
Planspiralfutter von RÖHM sind jeweils mit drei oder vier Backen verfügbar, dabei gibt es folgende Varianten:
Dreh- und Schleiffutter
ZG Hi-Tru:
- Radiale Feineinstellung für höchste
Rundlaufgenauigkeit
- Rundlauf auf unter 0,005 mm einstellbar
- Wiederholspanngenauigkeit 0,015 mm
- Gusskörper
- Feineinstellung ohne Lösen der Befestigungsschrauben
- Stahlaufnahmeflansch
- Auch als abgedichtete Variante
Kranzspannfutter
KRF:
- Drei- und Vierbackenfutter
- Gusskörper
- Positionieren und Befördern von ringförmigen Werkstücken
- Größen 125 bis 200: 4 Gewindestifte für Feineinstellung
- Mit und ohne Grundplatte
- Zylindrische Zentrieraufnahme
Planscheiben
RÖHM Planscheiben, bei welchen es sich um ein Vierbackenfutter mit Durchgang handelt, werden zur Einzelspannung eingesetzt. Sie sind besonders gut für die Spannung asymmetrischer Werkstücke sowie für die Längs- oder Planbearbeitung geeignet.
http://eshop.roehm.biz/roehm_de_de/online-shop/drehfutter-planscheiben.html
Raumschall Entkopplung mit vollflexiblen Lüftungsrohren der WesterQuadro Warengruppe zum Vorderwand- und Deckeneinbau bei gleichzeitig niedriger Raumhöhe geeignet. Dämpfung und Packungsdicke sind variabel.
Die am Reitstock angebrachten RÖHM Spitzen und Stirnseiten-Mitnehmer fixieren das zu bearbeitende Werkstück während des Bearbeitungsvorganges und sorgen dadurch für ein ausgesprochen exaktes Ergebnis, auch bei besonders langen und schweren Arbeitsstücken.
Sie kommen in Dreh- und Schleifmaschinen zum Einsatz und ermöglichen dabei ein Bearbeitung auf der ganzen Länge. Auch ist kein Umrüsten bzw. Umspannen erforderlich.
Mitlaufende Körnerspitze
Die mitlaufenden Körnerspitzen von RÖHM profitieren von einer angebrachten Spritzwasserrille, einer verbesserten Lebensdauerschmierung sowie eng tolerierten Lagersitzen und sind dadurch äußerst langlebig. Durch ihre schlanke Gehäuseform ist die Störkontur äußerst gering.
Außerdem ist der Körper dieser Zentrierspitze geschliffen und gehärtet.
Weitere Eigenschaften dieses RÖHM-Produkts sind:
• Dreifachlagerung
• Angebrachte Abdrückmutter
• Fester Aufnahmeschaft
• Hohe Rundlaufgenauigkeit
• Hohe Drehzahlen
• Hoch belastbar
Die mitlaufende Körnerspitze ist in verschiedenen Ausführungen verfügbar.
Dabei wird unterschieden zwischen:
• Pro, Standardausführung
• Heavy, für besonders schwere Werkstücke
• Speed, bei hohen Drehzahlen
• Slim, bei der Bearbeitung von sehr kleinen Werkstücken
• Control, mit Manometer zur Messung des Drucks
• Flex, für auswechselbare Einsätze z.B. bei Hohlkörpern oder zentrumslosen Werkstücken
Constant Stirnseiten-Mitnehmer
Bei den RÖHM Stirnseiten-Mitnehmern erfolgt die Drehmomentübertragung stirnseitig, wodurch das aufgespannte Werkstück ohne Umspannen auf seiner kompletten Länge bearbeitet werden kann. Dadurch kann die Rundlaufgenauigkeit wesentlich erhöht werden.
Die Constant Stirnseiten-Mitnehmer aus dem Hause RÖHM werden manuell gespannt.
CoE
Entwickelt nach dem Baukastenprinzip, weshalb ein universeller Austausch von Mitnehmer-Scheiben und Zentrierspitzen möglich ist. Infolge des mechanischen Druckausgleichs ergibt sich eine gleichmäßige Spannkraft, auch bei unebenen Stirnseiten des Werkstücks.
Durch die federnde Zentrierspitze erfolgt der Werkstück-Längenanschlag an der Stirnseite.
Neben dem Drehen auf ganzer Länge kann gleichzeitig eine Nut oder Verzahnung gefräst werden. Dies kann Umrüsten, z.B. auf einen Schraubstock sparen, was sich in einer Zeit- und Kostenersparnis bemerkbar macht.
• Werkstückgewicht max. 100 kg
• Spannkreis-Ø 8-80 mm
CoA
Entwickelt nach dem Baukastenprinzip, weshalb ein universeller Austausch von Mitnehmer-Scheiben und Zentrierspitzen möglich ist. Hydraulischer bzw. mechanischer Druckausgleich ermöglicht eine gleichmäßige Spannkraft, auch bei unebenen Stirnseiten des Werkstücks.
Durch die federnde Zentrierspitze erfolgt der Werkstück-Längenanschlag an der Stirnseite.
• Werkstückgewicht max. 100 kg
• Spannkreis-Ø 8-80 mm
http://eshop.roehm.biz/roehm_de_de/online-shop/spitzen-stirnseiten-mitnehmer.html
Multigrain Rice and Grain Eng Company is giving you the best options for your rice mill , Corn Mill , Storage , Drying and packing facilities and built it turn key with the highest milling yield and energy saving options
Sennebogen
Guia de Implementos para Manipulación de Materiales
Distribuido por Maquiandes para Venezuela, Colombia, Ecuador y America Central
www.maquiands.com
This document provides an overview of Pepperl+Fuchs' components and solutions for process automation. It discusses their focus on customer requirements and innovation in automation technologies. It also lists interface technology, remote I/O systems, fieldbus infrastructure, HMI solutions, explosion protection equipment, and customized solutions as part of their product portfolio.
The document provides technical specifications and dimensional drawings for various models of the LC series of planetary gear units, including the LC 050, LC 070, LC 090, LC 120, and LC 155. It includes details on symbols and definitions, selecting the appropriate gear unit based on application requirements, service life calculations for bearings, features of the LC series, ordering codes, and dimensional drawings with specifications for each model. Key information covered includes torque and speed ratings, bearing life, available ratios and motor couplings, dimensions, mass moments of inertia, and more. The document is a product catalogue for selecting and specifying the proper LC gear unit for given application needs.
HIDRAPAC is a manufacturer of hydraulic components for mobile industries. They produce high quality pumps, motors, valves and other components. HIDRAPAC prides itself on innovation, flexibility, and providing customized solutions to meet customer needs. Their products are used in construction equipment, agriculture, material handling, and other mobile machine industries worldwide.
The document is a catalog for LAK DC motors that provides specifications for various models. It includes information on power ratings from 1-500 kW, torque ratings from 30-4500 Nm, cooling options, mounting configurations, standards compliance, and performance data for different frame sizes. Dimensional drawings and ordering information are also referenced.
The document describes DC drive solutions from Control Techniques, including their Mentor MP and Quantum MP DC drives. The Mentor MP and Quantum MP are advanced digital DC drives that provide reliable motor control and flexible system interfacing capabilities. They integrate control functionality from Emerson's Unidrive SP AC drive and include options for expanded I/O, communications, feedback and automation capabilities through add-in modules. The drives can interface with modern industrial networks and are suitable for new DC motor applications as well as upgrades to existing DC motor systems.
This document provides specifications for motor bell housings used to connect electrical motors to gear reducers. It includes general specifications, assembly instructions, designation codes, verification requirements, dimensions for different frame sizes and gearbox combinations. Key information includes permissible bending moments and input power for different motor/gearbox configurations, dimensions for mounting the bell housings, mass properties, and designation codes for housing variants. Design features are also summarized, such as the housing material and available coupling types.
Rex and Link-Belt Spherical Roller Bearing Units RexnordArve
This document provides an overview and catalog of Rex and Link-Belt spherical roller bearing units. It includes sections on Rex spherical roller bearing units features and benefits, shaft mounting styles, seal ratings and speed limits, nomenclature, engineering selection guides, and housing styles. It also includes sections on Link-Belt spherical roller bearing units features and benefits, seal ratings and speed limits, nomenclature, engineering selection guides, housing styles, and replacement parts. The document serves as a reference for different bearing unit product lines, specifications, and application guides.
2. 2
Typschlüssel – Type code
PMG 180 L 06-23-A-F-E
= Anbauten Attachments
- = keine Anbauten no attachments
R = Resolver Resolver
E = Inkrementalgeber Encoder
S = Sin/Cos-Geber / Absolutwertgeber Sine-cosine encoder / absolute encoder
B = Bremse Brake
G = Getriebe Gear
T = Analogtacho Tacho-Generator
D = Digitaltacho Digital-Tacho-Generator
XX = weitere Anbauten other attachments
= Bauform Type of construction
F = Fußausführung foot mounted design
FL = Flanschausführung flange mounted design
FF = Fuß-Flanschausführung foot-flange mounted design
V = Vertikalausführung vertical execution
= Polpaarzahl Number of poles
A = 1 (2-polig) 1 (2-poles)
B = 2 (4-polig) 2 (4-poles)
C = 3 (6-polig) 3 (6-poles)
XX = weitere Polpaare other types of poles
= Schutzart Degree of protection
23 = IP 23 S IP 23 S
XX = IP… weitere Schutzarten IP… other types of protection
= Kühlart Cooling method
06
= IC 06 Innenkühlung, fremdbelüftet mit
Aufbaulüfter
IC 06 open-circuit air cooling, forced-
ventilated with top-mounted fan
17
= IC 17 Innenkühlung, fremdbelüftet mit
Kanalanschluss auf BS
IC 17 open-circuit air cooling, separately-
ventilated with duct on NDE
37
= IC 37 Innenkühlung, fremdbelüftet mit
Kanalanschluss auf AS u. BS
IC 37 open-circuit cooling, separately-
ventilated with duct on DE and NDE
71 = IC 71 W Wassermantelkühlung IC 71 W water-jacket cooling
86
= IC 86 W Innenkühlung mit aufgebautem
Luft-Wasser-Kühler
IC 86 W open-circuit cooling with fitted
air-to-water cooler
410 = IC 410 unbelüftet IC 410 totally-enclosed, non-ventilated
411 = IC 411 Oberflächenkühlung, eigenbel. IC 411 totally-enclosed, fan-cooled
416 = IC 416 Oberflächenkühlung, fremdbel. IC 416 totally-enclosed, forced-ventilated
616
= IC 616 Innenkühlung mit aufgebautem
Luft-Luft-Kühler
IC 616 open-circuit air cooling with fitted
air-to-air cooler
XX = IC … weitere Kühlarten IC … other cooling methods
= Baulänge Construction length
XS = sehr kurz very short
S = kurz short
M = mittel medium-sized
L = lang long
X = sehr lang very long
XL = extra lang extra long
XV = Sonderlänge special length
= Baugröße Frame
z.B. 180 = 180 mm Achshöhe 180 mm frame size
= Gehäuseausführung Type of housing
G = Standard standard
S = verstärktes Gehäuse rugged housing
W = Wassermantelgehäuse water jacket housing
PM = Drehstrom-Synchron-Motor AC synchronous motor
3. Technische Daten PMG – Technical data PMG
Standardausführung – Standard design
Kühlart IC 06 durchzugsbelüftet method of cooling IC 06 forced air ventilated
Schutzart IP 23 S nach DIN EN 60034-5 degree of protection IP 23 S / DIN EN 60034-5
Lüfteranbau B-seitig oben mit Kastenfilter fan mounting NDE radial top with box-filter
Bauform IM 1001 type of construction IM 1001
Klemmkasten rechts, B-seitig terminal box right, NDE
Anbauvorrichtung vorbereitet für Euro-Flansch mounting kit prepared for euro flange
Farbe RAL 4004 color RAL 4004
Isolation H/F insulation H/F
Motorschutz 3 Kaltleitertemperaturfühler motor protection 3 PTC for trip
Wellenende zylindrisch mit Nut u. Passfeder shaft extension cylindric with key
Wuchtung mit halber Passfeder balancing with half key
Schwinggrößenstufe A nach EN 60034-14 vibration severity grade A / EN 60034-14
Lager
A- u. B-Seite Rillenkugellager,
optional stromisolierte Rillenkugel-
lager
bearings
DE and NDE deep groove ball
bearings, optional insulated deep
groove ball bearings
Umgebungsbedingungen max. 40°C ambient temperature max. 40°C
Aufstellhöhe 1.000 müNN site altitude 1.000 m above sea level
motorische S1-Daten - motor operation S1
Bemessung - rating 75 Hz - 1.500 rpm - 3 x 360 V
Motor-Typ
Bemessungs-
leistung
Bemessungs-
moment
Bemessungs-
drehzahl
max.
Drehzahl
Bemessungs-
strom
Leistungs-
faktor
Massenträgheits-
moment
Masse
motortype
rated
power
rated
torque
rated
speed
max.
Speed
rated
current
faktor
power
moment
of inertia
weight
[kW] [Nm] [rpm] [rpm] [A] [cos ᵠ] [kgm²] [kg]
PMG 100 S 10 64 1.500 3.000 20 0,88 ~ 0,016 70
PMG 100 M 12 76 1.500 3.000 23 0,90 ~ 0,018 80
PMG 100 L 14 89 1.500 3.000 27 0,90 ~ 0,020 90
PMG 112 S 22 140 1.500 3.000 41 0,92 ~ 0,047 110
PMG 112 M 25 159 1.500 3.000 45 0,93 ~ 0,054 120
PMG 112 L 28 178 1.500 3.000 51 0,93 ~ 0,061 130
PMG 132 S 39 248 1.500 3.000 70 0,94 ~ 0,110 170
PMG 132 M 44 280 1.500 3.000 79 0,93 ~ 0,123 180
PMG 132 L 50 318 1.500 3.000 90 0,93 ~ 0,136 190
PMG 160 S 63 401 1.500 3.000 117 0,91 ~ 0,300 290
PMG 160 M 70 446 1.500 3.000 129 0,91 ~ 0,320 310
PMG 160 L 77 490 1.500 3.000 141 0,91 ~ 0,340 330
PMG 180 S 88 560 1.500 3.000 165 0,90 ~ 0,380 390
PMG 180 M 95 605 1.500 3.000 179 0,89 ~ 0,410 405
PMG 180 L 104 662 1.500 3.000 195 0,89 ~ 0,440 420
PMG 200 S 120 764 1.500 3.000 219 0,92 ~ 1,10 640
PMG 200 M 135 860 1.500 3.000 243 0,93 ~ 1,20 660
PMG 200 L 150 955 1.500 3.000 266 0,94 ~ 1,30 680
PMG 225 S 204 1.299 1.500 2.500 399 0,85 ~ 1,90 890
PMG 225 M 228 1.452 1.500 2.500 434 0,87 ~ 2,15 910
PMG 225 L 252 1.604 1.500 2.500 468 0,89 ~ 2,40 930
PMG 280 S 345 2.200 1.500 2.000 653 0,88 ~ 3,80 1.100
PMG 280 M 390 2.500 1.500 1.500 743 0,87 ~ 4,20 1.250
PMG 280 L 440 2.800 1.500 1.500 845 0,86 ~ 4,60 1.400
Abweichende Leistungen und Drehzahlen auf Anfrage – Different output and speed on request
4. Abmessungen PMG – Dimensions PMG
Flanschmaße
flange dimension
PMG a b s d f g1 g2 h j k l m n o p q r s t u v x y a1 b1 c1 e1 f1 s1
100 S 396
160 10 38k6 213 108 180 100 57
693
80 112 40 134 398 183 11 41 10 126 63
349
87 200 130j6 11 165 3,5 11100 M 427 724 380
100 L 462 759 415
112 S 362
190 10 48k6 277 108 209 112 40
778
110 58 40 150 465 273 12 51,5 14 114 70
371
147 200 130j6 23 165 3,5 11112 M 388 804 397
112 L 423 839 432
132 S 407
216 12 55m6 276 140 269 132 49
794
110 77 50 135 527 289 13 59 16 109 89
384
147 250 180j6 25 215 4 14132 M 443 830 420
132 L 479 866 456
160 S 485
254 14 65m6 264 167 317 160 62
942
140 86 60 171 636 289 13 69 18 108 108
511
147 300 230j6 28 265 4 14160 M 520 977 546
160 L 555 1012 581
180 S 492
279 15 70m6 256 187 337 180 75
966
140 92 70 197 642 343 15 74,5 20 98 121
502
147 350 250h6 24 300 5 18180 M 527 1001 537
180 L 562 1036 572
200 S 640
318 15 75m6 292 206 360 200 85
1143
140 97 75 214 707 410 20 79,5 20 103 133
593
197 400 300h6 30 350 5 18200 M 710 1213 663
200 L 780 1283 733
225 S 662
356 18 85m6 275 222 386 225 102
1214
170 107 90 241 785 410 20 90 22 104 149
665
197 430 350h6 35 400 5 18225 M 732 1284 735
225 L 802 1354 805
Abmessungen in mm Dimensions in mm
Änderungen vorbehalten Subject to change without prior notice