30120140501008

International Journal of Mechanical Engineering and Technology (IJMET), ISSN 0976 –
INTERNATIONAL JOURNAL OF MECHANICAL ENGINEERING
6340(Print), ISSN 0976 – 6359(Online) Volume 5, Issue 1, January (2014), © IAEME

AND TECHNOLOGY (IJMET)

ISSN 0976 – 6340 (Print)
ISSN 0976 – 6359 (Online)
Volume 5, Issue 1, January (2014), pp. 79-89
© IAEME: www.iaeme.com/ijmet.asp
Journal Impact Factor (2013): 5.7731 (Calculated by GISI)
www.jifactor.com

IJMET
©IAEME

PERFORMANCE AND EMISSION CHARACTERISTIC OF DI DIESEL
ENGINE WITH PREHEATING CORN OIL METHYL ESTER
R. SenthilKumar*,
*

M. Loganathan#,

P. Tamilarasan$

Research Scholar, Mechanical Engineering Annamalai University, Chidambaram, 608001,
Tamilnadu
#
Associate Professor, Mechanical Engineering, Annamalai University
$
Assistant Professor, Mechanical Engineering, Annamalai University

ABSTRACT
In this experimental investigation, the corn oil methyl ester (COME) was prepared by
transesterification using corn oil, methyl alcohol and potassium hydroxide (KOH) as a catalyst. The
fuel properties of bio-diesel such as kinematic viscosity and specific gravity were found within
limited of BIS standard. At different preheated temperatures of COME, the performance and exhaust
emission characteristics of a diesel engine fuelled with preheated bio-diesel were obtained and
compared with neat diesel. Experiments were conducted at different load conditions in a single
cylinder, four stroke, direct injection (DI) diesel engine. The engine was run by diesel and biodiesel
blends. The COME was preheated to temperatures namely 50, 70, and 90°C before it was supplied to
the engine. The brake thermal efficiency (BTE) and brake specific fuel consumption (BSFC)
calculated. The Exhaust gas temperature, smoke density, CO, HC, NOx emissions were measured
and compared with neat diesel operation. The results shown that the preheated bio-diesel is
favourable on BTE and CO, HC emissions when it is heated up to 70°C. At the same time the NOx
emission was increased. But at preheated temperature of 90°C, a considerable decrease in the BTE
and BSFC were observed due to the vapour locking in the fuel line caused by vapour formation due
to higher temperature of preheated biodiesel. The test results shows that bio-diesel preheated to 70°C
can be used as an alternate fuel for diesel fuel without any significant modification in expense of
increased NOx emissions.
Keywords: Fuel, Engine, Biodiesel, COME Methyl Ester, Vegetable Oil, Performance, Emission.

79

1. INTRODUCTION
Fast depletion of the fossil fuels, rising petroleum prices, increasing threat to the environment
from exhaust emissions and global warming have generated intense international interest in
developing alternative non-petroleum fuels for engines. In the context of fast depletion of fossil fuels
and increasing of diesel engine vehicle population, the use of renewable fuel like vegetable oils
become more important [Nadir Yilmaz et al., 2011; M.M, Conceicao et al., 2005; Yuan W., et al.,
2005]. Many alternative fuels like biogas, methanol, ethanol and vegetable oils have been evaluated
as a partial or complete substitute to diesel fuel. The vegetable oil directly can be used in diesel
engine as a fuel, because their percentage of energy content is high and nearly equal to diesel. The
technology of production, the collection, extraction of vegetable oil from oil seed crop and oil seed
bearing trees is well known and very simple. The oil is extracted from the corn seeds and converted
into methyl esters by the transesterification process. The methyl ester obtained from this process is
known as COME. Several researchers [T.W, Ryan et al., 1982] have used biodiesel as an alternate
fuel in the existing CI engines without any modification.
The emissions characteristics of diesel engines fuelled with neat biodiesel or its blends with
diesel fuel have been investigated by many researchers. They found that there are reductions in
carbon monoxide, hydrocarbon and smoke emissions [S. Puhan et al., 2005, ; M.E.G. Gomez et al.,
2000; S. Kalligeros et al., 2003], while there is increase in NOx emissions [Y. Lin,et al., 2007; M.P.
Dorado et al., 2003].The major drawback with the vegetable oils as fuel is its high viscosity [Deepak
Agarwala et al., 2008]. Higher viscosity of oils is having an adverse effect on the combustion in the
existing diesel engines [K. Babu et al., 2003]. Concept of preheating of biodiesel to bring the
viscosity equivalent to diesel. The viscosity of fuels have important effects on fuel droplet formation,
atomization, vaporization and fuel-air mixing process, thus influencing the exhaust emissions and
performance parameters of the engine. There have been some investigations on using preheated raw
vegetable oils such as cottonseed oil in diesel engines [Dilip Kumar et al., 2003]. However, it is
known that vegetable oils have considerably higher viscosity compared with diesel fuel. The main
objective of this experimental investigation is to determine the effects of the viscosity of corn oil
methyl ester, which is decreased by means of preheating process, on the performance parameters and
exhaust emissions of a diesel engine. For this aim, corn oil methyl ester was produced by
transesterification method using corn oil and methyl alcohol, and its properties were determined.
Then, this biodiesel was preheated up to three different temperatures and tested in the diesel engine
at all load conditions. Finally, the results for COME were compared with those for diesel fuel.
2. PRODUCTION OF BIODIESEL
2.1. Transesterification
Tranesterification is the most common method to produce biodiesel, which refers to a
catalyzed chemical reaction involving Vegetable oil, and an alcohol to yield fatty acid alkyl esters
and glycerol i.e. crude glycerine [Schwab A.W., et al., 1987; Antolin G., et al., 2003]. The process of
‘transesterification’ is sometimes named methanolysis or alcoholysis. This method is used to convert
the corn oil in to corn oil methyl ester. After transesterification, viscosity of Corn oil methyl esters
(COME) is reduced by 75-85% of the original oil value. It is also called fatty acid methyl esters, are
therefore products of transesterification of Corn oil and fats with methyl alcohol in the presence of a
KOH catalyst. During the reaction, high viscosity oil reacts with methanol in the presence of a
catalyst KOH to form an ester by replacing glycerol of triglycerides with a short chain alcohol.
[Triglycerides (Corn oil) + Methanol Corn oil methyl ester + Glycerol]

80

Methanol/methyl alcohol is preferred for COME preparation by using transesterification as it
provides better separation of methyl ester and crude glycerin thus facilitating the post-reaction steps
of obtaining biodiesel. The properties of diesel and COME shown in table 1.
Table.1: Properties of diesel and COME
Fuel

Diesel

COME

Calorific value (MJ/kg)

46.22

42.56

Kinematic viscosity,(mm2/s)@ 30°C

4.56

42.2

Density @ 20 C kg/m3

0.83

0.875

Flash Point °C

54

143

Fire Point °C

64

149

3. EXPERIMENTAL SETUP AND PROCEDURE
A single cylinder, water cooled, four stroke direct injection compression ignition engine with
a compression ratio of 16.5: 1 and developing 3.7 kW power at 1500 rpm was used for this work
(Figure. 1). The specification of the test engine is shown in table 2. The engine was coupled with an
eddy current dynamometer .Fuels used were diesel, corn oil methyl ester and blends at pre heated to
50°C, 70°C, 90°C. Load was applied in 5 levels namely, 20%, 40%, 60%, 80% and 100%. Load,
speed, air flow rate, fuel flow rate, exhaust gas temperature, exhaust emissions of HC, CO and
smoke were measured at all load conditions. The Redwood Viscometer is used to measure the
viscosity of fuels at various temperatures. The exhaust gas analyzer model Horiba MEXA-584L was
used to measure carbon monoxide (CO) and hydrocarbon (HC) levels. The analyzer is a fully
microprocessor controlled system employing non destructive infrared techniques.
Table.2: Specification of test engine
Make

Kirloskar AV-1

Type

Single cylinder, water cooled,

Max.power

3.7 kW at 1500 rpm

Displacement

550 CC

Bore x Stroke

80 x 110 mm

Compression ratio

16.5:1

Fuel injection timing

21deg BTDC

Loading device

Eddy current dynamometer

81


Figure.1: Schematic of Experimental setup
3. RESULT AND DISCUSSION
3.1 Variation of Kinematic Viscosity with temperature

Figure.2: The variation of viscosity of diesel, COME and blends at various temperatures
The figures.2 shows the variation of kinematic viscosity with temperature of diesel and
various blends of biodiesel namely COME20, COME40, COME60, COME80, COME100. The
diesel and blends of biodiesel are preheated for the temperature of 30°C, 50°C,70°C and 90°C. The
results shown that the kinematic viscosity of fuels decreased as preheated temperature increased. The
reduction percentage of kinematic viscosity increased upto the preheated temperature of 70°C. But
the variation of kinematic viscosity from 70° to 90°C is very small. The kinematic viscosity of
COME20, COME40, COME60, COME80 and COME100 are 3.1, 3.3, 4.6, 4.8, 4.8 and 8.3 mm2/s
respectively at preheated temperature 70°C. The kinematic viscosity of COME20 blends falls from
8.3 to 3.1% at 70°C, which 62.65 % less than COME100 at the same temperature.
82

3.2 Optimization of preheating temperature
The biodiesel and diesel are mixed in the proportion of 20% biodiesel and 80% diesel is
called B20. This blend was heated to the temperature 50°C, 70°C and 90oC.The performance test
was conducted for all the above preheated blend for different load. The variation of BSFC and BTE
are shown in figure 3 and 4 respectively. The results shown that the BSFC decreased for the blends
of B20 at the preheated temperature of 70°C compared to other preheated temperature namely 50°C
and 90°C. This is due to reduction of viscosity by heating the blend and hence better fuel spray
causes the reduction of fuel consumption. But in higher temperature namely for 90°C the fuel
consumption is more due to vapor locking in the fuel injection line. The BTE increased for the
preheated blend temperature of 70°C. This is because of better combustion taking place due to
improved spray characteristics of low viscosity fuel. But for other preheated temperatures namely
50°C and 90°C the BTE decreased due to poor mixture formation of higher viscosity of fuel. Hence
the optimum preheated temperature of 70°C is choosed for all blends for further test.

Figure.3: Variation of BSFC with brake power

Figure.4: Variation of Brake thermal efficiency with brake power at B20
83

3.3 Compression of performance and emission of all blends of biodiesel with diesel
3.3.1 Brake Specific fuel consumption
The variation of BSFC with brake power for different COME are presented in Fig.5. Here the
optimized preheated temperature of 70°C blends was used for test. The BSFC of all COME is higher
than that of diesel for all loads. For all COME tested, BSFC is found to decrease with increase in the
load. This is due to more blended fuel which is used to produce same power as compared to diesel.
The BSFC increased from 0.23Kg/Kwhr to 0.284Kg/Kwhr for diesel and COME 100 respectively at
full load. This is due to the effect of higher viscosity and poor mixture formation of COME.

Figure.5: Variation of Brake specific fuel consumption with brake powerat 70°C
3.3.2 Brake thermal efficiency
The variations of BTE of COME20, COME40, COME60, COME80, COME100 with
reference to diesel fuel are shown in Fig.6.The increase in BTE with COME operations can also be
attributed to the good combustion characteristics of bio-diesel owing to their decreased viscosity and
improved volatility by means of preheating process. It is seen that the BTE of COME decreased as
increasing the biodiesel quantity with diesel. The BTE of COME100 decreases 12.18 % as compared
to diesel at full loads. But BTE of COME 20 decreased 3.2% as compared to diesel at full load.

Figure.6: Variations of brake thermal efficiency with brake power
84

3.3.3 Exhaust gas temperature
The figure.7. shown the variation of exhaust gas temperature with power for all blends. There
is an increase Exhaust gas temperature with neat COME compared to other blends and diesel full
load. This is mainly due to higher viscosity of COME leads to delayed burning of fuel. In the exhaust
pipe. The exhaust gas temperature reduces as the proportion of diesel is raised due to the better
vaporization of mixture.
The exhaust gas temperature increased 7.7% for COME100 compared to diesel at full load.
The reduction in the exhaust gas temperature of the blends shows that the premixed combustion of
the blend has improved. This is mainly due to the reduction in the viscosity of the fuel.

Figure.7: Variation of exhaust gas temperature with brake power
3.3.4 Smoke density
The variation of smoke density for different COME is shown in Fig. 8. The Smoke density of
COME is lower than that of the diesel oil. The smoke density increased as the concentration of the
COME increased. This is due to poor mixture formation and uneven fuel spray pattern in the
combustion chamber. The smoke density increases from 76.9 to 81.8 HSU for diesel and COME100
at full load.

Figure.8: Variation of Smoke density with brake power
85

3.3.5 CO, HC and NOx emissions
The CO emissions are shown in Fig. 9. As seen in the figure, the CO emission increase with
increase of engine load, due to rich fuel air mixture. Compared with the diesel fuel, the CO emissions
of COME are higher, because of the poor combustion. Therefore, the CO emissions increased due to
incomplete combustion.. The CO emission of COME 100 is 16.66 % higher than the diesel at full
load. The CO emission of COME 20 is 0.134 % by v and it is very close to diesel CO emission.

Figure.9: Variation of CO emission with brake power

Figure.10: Variation of HC emission with brake power
Fig. 10 shows the variation of HC emissions. Similar to the CO emissions, the HC emission
increases with increases % of the engine load. Compared with diesel fuel, COME give lower HC
emission. The HC emission of COME100 decrease 25.5 % at the maximum load of the engine in
comparison with diesel fuel. The higher oxygen content of COME leads to better combustion,
resulting in lower HC.
86


Figure.11: Variation of NOx emission with brake power
Fig.11 shows the variation of the NOx emissions of the test engine for COME with reference
to diesel fuel. It is seen that the COME operations usually yield higher NOX emissions at all loads
compared to diesel fuel operations. The increase in NOx emissions with COME may be attributed to
various reasons, such as better combustion of biodiesel due to its high oxygen content and higher
temperatures in the cylinder as a result of preheating. The maximum increase in NOX emissions were
obtained in COME100. The NOX emissions with COME100 increase approximately 14.04 % as
compared to diesel fuel at full load.
5. CONCLUSION
Corn oil methyl ester (COME) was produced by means of transesterification process using
corn oil, which can be described as a renewable energy source. The viscosity of COME was reduced
by preheating it before supplied to the test engine. After the fuel properties of COME has been
determined, various performance parameters and exhaust emissions of the engine fuelled with
COME and COME blends preheated at different temperatures were investigated and compared with
those of diesel fuel. The experimental conclusions of this investigation can be summarized as
follows:
Preheating of COME makes significant decrease in its kinematic viscosity and a small
decrease in specific gravity. It is almost nearer to the values of diesel fuel.
The preheated temperature of COME20 was optimized for 70°C by considering maximum
BTE and minimum BSFC.
The Brake Specific Fuel Consumption (BSFC) increased from 0.23 kg/kwhr to 0.284
kg/kwhr for diesel and COME100 respectively at full load.
Lower BTE is found with the COME100 is 30.12 % compared to diesel 34.3 %. However for
the blend of COME20 the increases of 9.27% as compared with neat COME100.
The use of COME20 produced a considerable decrease in CO emissions. CO emissions
obtained with COME20 operations were 14.12 % lower than that of neat COME100 and 2.98
% higher than diesel fuel operations.
Compared with diesel fuel, COME100 gives nearly 25.5 % lower value of HC emissions at
the maximum load of the engine.
87

NOx emissions were increased due to higher combustion temperatures caused by preheating
and oxygen content of COME100. The maximum increase in NOx emissions were obtained
in the case of COME100.
The smoke density of COME60 preheated oil is approximately equal to the neat diesel fuel
operations at full load.
The exhaust gas temperature COME100 increased 7.7% compared to diesel at full load.
In general, if is concluded that the preheated temperature of COME20 blends was optimized
from 70°C. Based on the performance and emission results of COME20 blends was choosed for
experiments.
7. REFERENCES
1.
2.
3.
4.

5.

6.

7.

8.
9.
10.
11.

12.
13.

14.

Nadir Yilmaz, Byron Morton. (2011). Effects of preheating vegetable oils on performance
and emission characteristics of two diesel engines Biomass and Bioenergy 35: 2028-2033.
M.M, Conceicao, R.A, Candeia, HJ, Dantas, L.E.B, Soledade, VJ, Fernandes, A.G. Souza.
(2005). Rheological behaviour of castor oil biodiesel Energy & Fuels 19: 2185- 2188.
Yuan W., A.C. Hansen, Q. Zhang. 2005. Vapour pressure and normal boiling point
predictions for pure methyl esters and biodiesel fuels. Fuel. 84: 943-950.
T.W, Ryan, T J, Callahan, L.G. Dodge. (1982). 'Characterization of vegetable oils for use as
fuel in diesel engines, Proceedings International Conference on Plaint Oils as Fuels American
Society of Agricultural Engineers, 82-4: 70-81.
S. Puhan, N. Vedaraman, G. Sankaranayanan, B.V. Bharat Ra. (2005). Performance and
emission study of mahua oil (madhucaindica oil) ethyl ester in a 4 stroke natural aspirated
direct injection engine, Renewable Energy 30 : 269-1278.
M.E.G. Gomez, R.H. Hildige, J.J. Leahy, T.O. Reilly, B. Supple, M. Malon. (2000)
Emission and performance characteristics of a diesel van operating on esterified waste oil and
diesel fuel, Environment Monitoring and Assessment 65: 13-20.
S. Kalligeros, F. Zannikos, S. Stournas, E. Lois, G. Anastapoulas, C. Teas, F.
Sakellaropoulos. (2003) An investigation of using biodiesel/marine diesel blends on the
performance of a stationary diesel engine, Biomass and Bio energy 24 : 141-149.
Y. Lin, Y.G. Wu, C. Chang. (2007) . Combustion characteristics of waste-oil produced
biodiesel/diesel fuel blends, Fuel 86: 1772-1780.
M.P. Dorado, E. Ballesteros, J.M. Arnal, J. Gomez, F.J. Lopez.(2003). Exhaust emissions
from a diesel engine fuelled with transesterified waste olive oil, Fuel 82 : 1311-1315.
M.N. Nabi, M.S. Akhter, M.M.Z. Shahadat.(2006). Improvement of engine emissions with
conventional diesel fuel and diesel-biodiesel blends, Bio resource Technology 97: 372-378.
Deepak Agarwala, LokeshKumarb, Avinash Kumar Agarwalb. (2008). Performance
evaluation of a vegetable oil fuelled compression ignition engine Renewable Energy 33:
1147–1156
K. Babu and G. Devaradjane.. (2003). “Vegetable oil and their derivatives of fuel for C.I
engines: An Overview”, SAE Technical Paper Series, Paper No. -01-0767
Dilip Kumar Bora, Milton Polly, VikasSandhuja and L. M. Das. (2004). “Performance
evaluation and emission characteristics of a diesel engine using mahua oil methyl ester
(MOME)”, SAE Technical Paper Series-28-0034.
M. Martin, D. Prithviraja.(2011) . Performance of Pre-heated Cotton seed Oil and Diesel Fuel
Blends in a Compression Ignition Engine, JJMIE, 5: 235-240

88

15. D. Subramaniama, A. Murugesanb, A. Avinasha, A. Kumaravela. (June 2013) Bio-diesel
production and its engine characteristics—An expatiate view. Renewable and Sustainable
Energy Reviews 22: Pages 361–370
16. Schwab A.W., M.O. Bagby, B. Freedman. (1987). Preparation and properties of diesel fuels
from vegetable oils. Fuel. Vol. 66, pp. 1372-1378.
17. Antolin G., I.V. Tinaut, Y. Briceno, V. Castano, C. Perez, A.I. Ramirez. (2002). Optimization
of biodiesel production by sunflower oil transesterification. Bioresource Technology.
83: 111-114.
18. V.Narasiman, S.Jeyakumar, M.Mani and K.Rajkumar, “Impact of Combustion on Ignition
Delay and Heat Release Curve of a Single Cylinder Diesel Engine using Sardine Oil as a
Methyl Ester”, International Journal of Mechanical Engineering & Technology (IJMET),
Volume 3, Issue 3, 2012, pp. 150 - 157, ISSN Print: 0976 – 6340, ISSN Online: 0976 – 6359.
19. A. Swarna Kumari, Ch.Penchalayya, A.V. Sita Rama Raju and D.Vinay Kumar,
“Performance Characteristics for the use of Blended Safflower Oil in Diesel Engine”,
International Journal of Advanced Research in Engineering & Technology (IJARET),
Volume 4, Issue 3, 2013, pp. 26 - 32, ISSN Print: 0976-6480, ISSN Online: 0976-6499.
20. K Srinivasa Rao, Dr. A Ramakrishna and P V Rao, “Performance and Emission
Characteristics of Di-Ci Diesel Engine with Preheated Chicken Fat Biodiesel”, International
Journal of Mechanical Engineering & Technology (IJMET), Volume 4, Issue 3, 2013,
pp. 177 - 190, ISSN Print: 0976 – 6340, ISSN Online: 0976 – 6359.
21. Sanjay Patil, “Effect of Injector Opening Pressure on Performance, Combustion and
Emission Characteristics of C.I. Engine Fuelled with Palm Oil Methyl Ester”, International
Journal of Mechanical Engineering & Technology (IJMET), Volume 4, Issue 1, 2013,
pp. 233 - 241, ISSN Print: 0976 – 6340, ISSN Online: 0976 – 6359.
22. Mahesh P. Joshi and Dr. Abhay A. Pawar, “Experimental Study of Performance-Emission
Characteristics of Ci Engine Fuelled with Cotton Seed Oil Methyl Ester Biodiesel and
Optimization of Engine Operating Parameters”, International Journal of Mechanical
Engineering & Technology (IJMET), Volume 4, Issue 1, 2013, pp. 185 - 202, ISSN Print:
0976 – 6340, ISSN Online: 0976 – 6359.

89

30120140501008

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Was ist angesagt?

Was ist angesagt? (18)

Andere mochten auch

Andere mochten auch (8)

Ähnlich wie 30120140501008

Ähnlich wie 30120140501008 (20)

Mehr von IAEME Publication

Mehr von IAEME Publication (20)

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

30120140501008