Flux is a substance cleaning agent that removes any lingering silver 925 oxide from the shell of the decision and the bond itself and allows the silver 925 fuse to gush liberally, preventing ‘blobbing’. The best unrest is a borax paste, which is openly nifty to the locale.. Silver 925 soldering lacking the use of unrest is not advised, as the resultant end will be deficient and the fuse will have a trend to pit, departure a lopsided and fairly horrid bond.

1. Learning how to sterling silver 925 union is a necessary aptitude in making good quality
jewellery. The application of sterling silver 925 soldering is one that should be approached
with a little caution at first, as you are using high temperature blowtorches to melt the
fuse against the metal. It could be very tranquil to make mistakes, so a sterile funnel to
the basics should help you to minimise the mistakes and preclude you from killing too the
property.
Types of darn
There are four crucial grades of silver 925 fuse and they are classified according to their
melting points as ex-painless, cool, avenue and hard. Ex-calm and simple silver 925
solders melt at a poorer temperature and are best worn for repair work or, when a minor
temperature is necessary. If bond is necessary at two or three joints near one another, it is
best to jerk with Hard poignant down to Easy to avert melting the before soldered locale.
Preparation
Before silver 925 soldering, guarantee that the facade you’re running on is thoroughly
cleaned. Any grease (even from a fingerprint) can involve how well the connect ‘takes’ to
the metal, so clean the model tenderly before beginning. You can then assuage the silver

2. 925 to be attached by a manner know as annealing by applying the flame of a blowtorch
to the region that wishes to be soldered pending the metal heats up to a dull pink colour.
Check that there was no gaps between the two pieces of metal that you want to join.
Silver 925 bond acts in a duct show when heated, meaning that it flows along the means
of slightest resistance. Any gaps will tolerate the join to run down on one seeming of the
seam and the ensuing complete will be mediocre.
Flux is a substance cleaning agent that removes any lingering silver 925 oxide from the
shell of the decision and the bond itself and allows the silver 925 fuse to gush liberally,
preventing ‘blobbing’. The best unrest is a borax paste, which is openly nifty to the locale..
Silver 925 soldering lacking the use of unrest is not advised, as the resultant end will be
deficient and the fuse will have a trend to pit, departure a lopsided and fairly horrid bond.
Applying the stage
Once the linkage is caked on both surfaces with unrest, you can then request boil to the
locale. Torch soldering is maybe one of the most customary methods, Choose a torch with
an adjustable flame mass. The ensures that you do not roast and scorch the metal, dulling
the shell and even potentially buckling the metal. The flame shouldn’t surplus over one
locale for any span of time – rather the torch should be stirred constantly to thwart the
metal overheating. Once the rectify temperature has been reached, the join should change
form from a real parade to a liquid and flood evenly into the common. Alternately, if the
silver 925 solder is in lead form, the tip is fed carefully onto the metal where it should melt
on commerce and once again, flow smoothly into the seam.
Finishing
Once the sterling silver 925 soldering has been done and the instance has cooled, it can
be cleaned to eradicate any remaining flux by sopping it in hot water. If this proves hard, a
weak blend (5-10%) of sulphuric acid can be worn followed by rinsing the case in hot
water. This route is known as “pickling” However, if you are incorporating gemstones into
your work, be awake that even a weak acid answer can harm the surface of more
permeable gravel.
Company: Yiwu Dushang Jewelry Co.,Ltd
Address: 3f,No.13-15,Building 4,A zone,Futian jewelry street,yiwu
city,zhejiang,china(322000)
Site: http://www.sterling-silver-925.com