Presentation joining processes
•Als PPT, PDF herunterladen•
14 gefällt mir•7,686 views
The document discusses various welding and joining processes. It describes oxy-fuel gas welding and cutting, which uses a fuel gas and oxygen to produce different flame types for welding metals. Arc welding processes like shielded metal arc welding and gas metal arc welding are also covered, which use an electric arc between an electrode and workpiece to produce heat. The document outlines safety considerations and procedures for various welding methods.
Empfohlen
Weitere ähnliche Inhalte
Was ist angesagt?
Was ist angesagt? (20)
Andere mochten auch
Andere mochten auch (20)
Ähnlich wie Presentation joining processes
Ähnlich wie Presentation joining processes (20)
Mehr von R G Sanjay Prakash
Mehr von R G Sanjay Prakash (20)
Kürzlich hochgeladen
Kürzlich hochgeladen (20)
Presentation joining processes
- 2. WELDING Definition: Material joining process. Two parts connected at their contacting surfaces by suitable heat and pressure. Many welding processes are accomplished by heat alone, some others by heat and pressure, and some with pressure only. In some welding operations a filler material is used. Welding operation usually applied to metals but also used for plastics.
- 12. Weld Joint Structure Characteristics of a typical fusion-weld zone in oxyfuel-gas and arc welding. Microhardness (HV) profile across a weld bead. A fusion joint is far from homogenous. Degree of inhomogeity increases from pure metals to multiphase alloys.
- 14. Weldability and Weld Quality - Welding Defects-
- 17. Weld Joints
- 19. Fillet Weld Groove weld Slot and Plug Weld
- 21. Oxyacetylene Gas Welding Three basic types of oxyacetylene flames used in oxyfuel-gas welding and cutting operations: (a) neutral flame; (b) oxidizing flame; (c) carburizing, or reducing, flame. The gas mixture in (a) is basically equal volumes of oxygen and acetylene. (d) The principle of the oxyfuel-gas welding operation.
- 22. Oxyacetylene Torch The acetylene valve is opened first; the gas is lit with a spark lighter or a pilot light; then the oxygen valve is opened and the flame adjusted. Basic equipment used in oxyfuel-gas welding. To ensure correct connections, all threads on acetylene fittings are left-handed, whereas those for oxygen are right-handed . Oxygen regulators are usually painted green, and acetylene regulators red.
- 34. Arc Welding
- 45. Schematic illustration of the shielded metal-arc welding process. About 50% of all large-scale industrial welding operations use this process. Consumable Electrode Arc Welding Shielded-Metal Arc Welding
- 47. (a) Schematic illustration of the gas metal-arc welding process, formerly known as MIG (for metal inert gas) welding. (b) Basic equipment used in gas metal-arc welding operations. Consumable Electrode Arc Welding Gas - Gas Metal-arc Welding Process-
- 51. Thermit Welding
- 54. Forge welding
- 55. Soldering Circuit Board Resistor Solder Pads Side View Top View PCB – printed circuit boards
- 56. Soldering Iron
- 57. Move soldering iron until tip is touching wire & solder pad
- 58. Move solder to touch edge of tip. Solder
- 59. Hold until solder melts on tip by wire Solder
- 60. Move solder back to touch wire only Solder
- 61. Move solder in to form a small pocket Solder
- 62. Move soldering iron tip up. This will drag solder up with it. Solder
- 63. Look for shinny fillets
- 74. Any Questions ??
Hinweis der Redaktion
- In this Welding, Cutting, and Brazing module, three specific types of welding are covered. These are listed below: Oxygen-fuel gas welding and cutting Arc welding and cutting Resistance welding.
- Electric current and mechanical pressure Resistance to the flow of current heats the material. Pressure is simultaneously applied to the joint, forming a solidified nugget that attaches the pieces.
- I. Speaker’s Notes: Acetylene is extremely dangerous because of its flammability range. Oxyacetylene torch cutting is very common throughout the industry as it has a wide flammable range. Acetylene is extremely unstable. Acetylene is generated in the cylinder from a reaction of acetone and calcium silicate. Relief valves for generating chamber shall be set to open at a pressure not in excess of 15 psi. Using acetylene at pressures in excess of 15 psig pressure (or about 30 psia pressure) is a hazardous practice. II. Speaker’s Notes: This slide lists basic rules to follow when welding with oxyacetylene. Before connecting to the regulator, always blow out the cylinder valve. Release the regulator by adjusting the screw before opening the cylinder valve. Always stand to the side of the regulator while opening the cylinder in case of accidental pressure release. Open the valve cautiously and slowly. Never use acetylene at pressures above 15 pounds per square inch.
- I. Speaker’s Notes: Before lighting the torch, remember to purge acetylene and oxygen passages. Before opening the oxygen on the torch, light the acetylene. Never use oil or grease on regulators, tips, or any part that may come into contact with oxygen. Do not use oxygen as a substitute for air. Always keep your work area free of items that could ignite.
- Speaker’s Notes: Oxygen : When oxygen is supplied to a service piping system from a low pressure oxygen manifold without an intervening pressure regulating device, the piping system shall have a minimum design pressure of 250 psig. A pressure regulating device shall be used at each station outlet when the connected equipment is for use at pressures less than 250 psig. Acetylene or Acetylene Compounds : Piping for acetylene or acetylenic compounds shall be steel or wrought iron.
- Speaker’s Notes: Pressure Relief Devices : Relief valves will vent automatically at preset pressures or may be manually operated to relieve pressure in the system.
- Speaker’s Notes: The three function : The protective equipment in fuel-gas piping systems shall be located either at the main supply line, at the head of each branch line, or at each location where fuel-gas is withdrawn
- Speaker’s Notes: Local exhaust Ventilation have enough velocity to draw away the contaminants. Natural Ventilation : Welding is not done in a confined space, and Welding space does not contain partitions, balconies or structured barriers that obstruct cross ventilation Mechanical Ventilation: These systems consist of hoods positioned at a distance from the work area.