Weitere ähnliche Inhalte
Ähnlich wie IRJET - A Review on Green Blocks and Strips using Plastic Mud (20)
Mehr von IRJET Journal (20)
Kürzlich hochgeladen (20)
IRJET - A Review on Green Blocks and Strips using Plastic Mud
- 1. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 07 Issue: 03 | Mar 2020 www.irjet.net p-ISSN: 2395-0072
© 2020, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 1655
A Review on Green Blocks and Strips Using Plastic Mud
Vishwa Tharun ch1, Dr. M.Vanathi1
1Student, Department of Civil Engineering, Guru Nanak Institutions Technical Campus, Ibrahimpatnam, India-501506
2Associate Professor, Department of Civil Engineering, Guru Nanak Institutions Technical Campus, Ibrahimpatnam,
India-501506
-----------------------------------------------------------------------------****--------------------------------------------------------------------------------
Abstract - All over India, plastic waste disposal becomes a
challenge to the environment. There is no safe way to
dispose plastic waste and waste causes serious damage to
environment, to overcome this problem the experiment
investigation is performed to manufacture blocks from
plastic wastages instead cement, aggregates and water.
Plastic represents the environmental issue. The disposal of
plastic is an uncontrolled manner. So as soon as possible
reduced the plastic from the world. In this case mixture of
plastic and sand used as decorating materials, plastic
blocks, covering strips for beam and columns, tiles as foot
paths for road and any residential and commercial
buildings, doors and window frames, roofs, ceilings,
pavements, bricks, decorating materials, barricades i.e
wheels for road side flex rollers showing speed limits with
replacement of iron, insulating materials. It is that strength
of blocks are increased by using mixture of plastic to the
sand. So it is observed that the strength of soil is increased
and compressibility is decreased by addition of plastic with
sand. The plastic blocks improves the workability and
economical. This investigation deals with proper reduction
plastic waste and useful things manufacture with plastic and
sand. The plastic is molded into any desire shape. So that
plastic is best ingredient for civil engineering constructions.
Different shades can obtained by mixing coloring agents
such as red oxide. Hence in this experiment investigation
attempt is made to study regarding the manufacture of
blocks by using plastic and sand.
Key words : Plastic waste, compressive strength, tensile
strength, strips, workability, eco friendly environment, green
blocks.
1. INTRODUCTION
Present and future days plastic utilization is high in all
over world. The plastic using is advantage to the people
and more disadvantages also. So reduce the plastic for life
time. Plastics are the most versatile materials ever
invented and have become a universal material, used for
everything from water bottles to wings on aircraft. When
compared to other materials and have contributed greatly
to quality of our everyday life. Plastics are malleable and
molded into any types of solid objects. Thus introducing
the plastic and sand mixing thoroughly and getting the
blocks for civil engineering constructions. As population
grows, plastic uses are also grows day by day life. In the
world every year 300 million tons of plastic is producing,
50% of moments, but on the planet for at least several
hundred years More than 8 million tons of plastic is
dumped into our oceans every year. The quality which is
for single use purposes-utilized for just a few of plastic
waste in municipal solid waste (MSW) is expanding
rapidly. It is estimated that rate of expansion is double for
every 10 years, this is due to rapid growth of population,
urbanization, development activities and changes in life
style which leading widespread littering on the landscape.
Plastics have many good characteristics which include
versatility, lightness, hardness and resistant to chemicals,
water and impart. Plastics are expanded to produce
materials of low density. Dissolved in solvents or
dispersed as emulsions, they are used in paints, varnishes
and adhesives. At present plastics find use in building
constructions mainly in thin coverings, panels, sheets,
foams, pipes, etc.
2. OBJECTIVES
The main objective of this investigation is to:
Reduce the disposal problems of plastic waste and
make environment eco friendly.
To improve the strength properties of the blocks.
To reduce the land fill problems and also to
control the depletion of natural resources.
To reduce the cost effective analysis.
3. NEED
Why we use plastic?
The following are the points for need of plastics in
construction:
Corrosive resistant
Light in weight
Easy to transport
Economical
Reduce toxic gases
Perfect shape and very convenient
Durability is more
Great workability
- 2. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 07 Issue: 03 | Mar 2020 www.irjet.net p-ISSN: 2395-0072
© 2020, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 1656
Weather resistance
Sound absorption
Fire resistant
Good appearance
4. METHODOLGY
To find properties of plastic waste.
To find physical properties of sand.
To conduct mixed design for plastic and sand.
To study the compressive and tensile strengths.
To study load bearing capacity.
5. LITERATURE REVIEW
An experimental investigation says that replacement of
cement with addition of plastic gives the strength is
slightly different. Plastic (70%) and sand (fine aggregate)
is 30% gives higher strength, when the addition of suitable
admixtures for molding different shapes and sizes.
5.1 Tokyay et al (1997)
The results of Tokyay et al (1997) on different sized
shapes and specimen sizes gives compressive strength of
high strength concrete. The compressive strength
increased 50% and tensile strength increased by addition
of waste plastic and tensile strength increased up to 10%
replace the weight of the cement instead of cement plastic
blocks weight is very less and more durable.
5.2 Dinesh et al (2018)
The studied that he plastic sand paver blocks possess more
advantages which include cost efficiency, removal of waste
products thus abolishing the land requirement problem for
dumping plastic is investigated. The study explains
reduction in emission of green house gases by the
conversion of fuel gases into synthetic oil.
5.3 Prem Kumar k (2017)
Evaluated that the paper based on experimental results of
effect of addition of waste plastics to bricks production in
different percentages subjected water curing is conducted
to find the characteristic compressive strength and water
absorption value of bricks. The test results shows that
partial replacement of natural sand by crushed waste
plastic at the levels 5 to 10% has good effects on
compressive strength.
5.4 Lairenlakpam et al (2017)
The study suggested that the making bricks from sand and
waste plastics can be an alternative is the available
traditional clay bricks sand plastics have lower water
absorption, bulk density and apparent porosity when
compared with those of normal, have higher compressive
strength than normal clay bricks.
5.5 Nivetha C et al (2016)
The study represents the proportion PPB-2 which having
the PET-30%, Fly ash -25% and quarry dust 45% gives
more strength when comparing with all other proportions.
Solid waste (quarry dust, fly ash & PET) can be used as an
main constituents for the preparation of paver block with
the increased strength.
5.6 Rajarapu Bhushaiah et al (2019)
The investigation based on plastic sand bricks, reduce the
usage of clay in making of bricks. Compressive strength of
plastic sand brick is 5.6 N/mm2 at the compressive load of
96KN. Water absorption of plastic sand brick is zero
percentage.
5.7 Sarang Shashikant Pawar et al (2017)
The observed paper presents the plastic in paver block 20-
40% at plastic may reduce, it is also dangerous to
environment and wildlife strength increases up to 30-35%.
Economical, increase properties of concrete.
5.8 Panimayam A et al (2017)
The experimental investigation represents the
compressive strengths of modified cement concrete are as
equal as plain cement concrete. The optimum modifier
cement of waste plastics are found to be 4% for
paverbricks. The cost of the construction will reduced.
5.9 Mohan D M S et al (2018)
The test results shows that the modified pavement block is
applicable in the construction of rigid pavements. The
block consists of quarry dust, fine aggregate, plastics out at
which the fine aggregate and quarry dust percentage is 60
to 70. The compressive strength of modified pavement
block are equal as conventional block. By using plastics in
pavement block, reduces the weight up to 15%. The best
option for the disposal of plastic and ultimately reduces
plastic pollution in the environment.
6. CONCLUSION
The above analysis concludes that the waste plastic is used
for manufacture the plastic blocks with mixture of sand.
The replacement of cement concrete with plastic and sand
is applicable in construction purposes. The cost of the
- 3. International Research Journal of Engineering and Technology (IRJET) e-ISSN: 2395-0056
Volume: 07 Issue: 03 | Mar 2020 www.irjet.net p-ISSN: 2395-0072
© 2020, IRJET | Impact Factor value: 7.34 | ISO 9001:2008 Certified Journal | Page 1657
construction also reduced, environment clean and green,
eco-friendly.
7. REFERENCES
[1] Rajarapu Bushaiah, Shaik Mohammad, D.Srinivasa
Rao(2019), “Study of Plastic Bricks made from
Waste Plastic” International Research Journal of
Engineering(IRJET), e-ISSN:2395-0056, p-
ISSN:2395-0072, volume:6, issue:4, pp:1122-
1127.
[2] S.Dinesh, K.Mohammad Shalman Parishee,
J.Sriram, M.Mohamed Bashith,
R.Jayasankar(2018), “Effective use of Waste
Plastic as Manufacturing of Paver Block”,
International Journal of Advanced Research in
Basic Engineering Sciences and
Technology(IJARBEST), ISSN:2456-5717,
volume:4, issue:5, pp:231-235.
[3] Mohan D.M.S, Vignesh.J, Iyyappan.P,
C.Suresh(2018), ”Utilization of Plastic Bags in
Pavement Blocks”, International Journal of Pure
and Applied Mathematics, ISSN:1314-3395,
volume:119, No.15, pp;1407-1414.
[4] A.Panimayam, P.Chinnadurai, R.Anuradha,
K.Pradeesh, A.UmarJaffer (2017) ”Utilization of
Waste Plastics As a Replacement of Coarse
Aggregate in Paver Blocks” International
Journal of ChemTech Research, ISSN:2455-9555,
volume:10, No.8, pp:211-218.
[5] Sarang Shashikant Pawar, Shubhankar Anant
Bujone (2017), ”Use of Fly Ash and Plastic in
Paver Block”, International Research Journal of
Engineering and Technology(IRJET), e-
ISSN:2395-0056, p-ISSN:2395-0072, volume:04,
issue:11, pp:1542-1547.
[6] K.PremKumar, M.Gouthami(2017), “Production of
Construction Bricks by Partial Replacement of
Waste Plastics”, IOSR Journal of Mechanical and
Civil Engineering (IOSR-JMCE), e-ISSN:2278-1684,
p-ISSN:2320-334X, volume:14, issue:4, pp:09-12.
[7] Lairenlakpam Billy graham Singh, Loukham
Gerion, pongsumbam boss
Singh,SureshThokchom(2017), ”Manufacturing
Bricks from Sand and Waste Plastics”,
International Journal of Engineering
Technology, Management and Applied Sciences,
ISSN:2349-4476, volume:5, issue:3, pp:426-
428.
[8] Nivetha.C, Rubiya.M, Shobana.S, Vaijayanthi.R,
G.Viswanatham M.E(2016), ”Production of Plastic
Paver Block from the Solid Waste(Quarry Dust,
Fly Ash & PET)”, ARPN Journal of Engineering and
Applied Sciences, ISSN;1819-6608, volume:11,
No:2, pp:1078-1079.
[9] Dr.Muhammad Maqbool Sadiq, Muhammad
Rafique Khattak(2015), ”Literature Review on
Different Plastic Waste Materials Use in Concrete”,
ISSN:2349-5162, volume:2, issue:6, pp:1800-
1803