Published patent and design registration information october 30th, 2015

The Patent Office Journal 30/10/2015 58670
पेटेंट कार्ाालर्
शासकीर् जर्ाल
OFFICIAL JOURNAL
OF
THE PATENT OFFICE
नर्र्ामर् सं. 44/2015 शुक्रवार दिर्ांक: 30/10/2015
ISSUE NO. 44/2015 FRIDAY DATE: 30/10/2015
पेटेंट कार्ाालर् का एक प्रकाशर्
PUBLICATION OF THE PATENT OFFICE

INTRODUCTION
In view of the recent amendment made in the Patents Act, 1970 by the Patents (Amendment) Act, 2005
effective from 01st
January 2005, the Official Journal of The Patent Office is required to be published under
the Statute. This Journal is being published on weekly basis on every Friday covering the various proceedings
on Patents as required according to the provision of Section 145 of the Patents Act 1970. All the enquiries on
this Official Journal and other information as required by the public should be addressed to the Controller
General of Patents, Designs & Trade Marks. Suggestions and comments are requested from all quarters so that
the content can be enriched.
( Rajiv Aggarwal )
CONTROLLER GENERAL OF PATENTS, DESIGNS & TRADE MARKS
30th
OCTOBER, 2015

CONTENTS
SUBJECT PAGE NUMBER
JURISDICTION : 58673 – 58674
SPECIAL NOTICE : 58675 – 58676
EARLY PUBLICATION (DELHI) : 58677 – 58683
EARLY PUBLICATION (MUMBAI) : 58684 – 58705
EARLY PUBLICATION (CHENNAI) : 58706 – 58729
EARLY PUBLICATION (KOLKATA) : 58730
PUBLICATION AFTER 18 MONTHS (DELHI) : 58731 – 59130
PUBLICATION AFTER 18 MONTHS (MUMBAI) : 59131 – 59268
PUBLICATION AFTER 18 MONTHS (CHENNAI) : 59269 – 59448
PUBLICATION AFTER 18 MONTHS (KOLKATA) : 59449 – 59628
PUBLICATION UNDER SECTION 43(2) IN RESPECT OF
THE GRANT (DELHI) : 59629 – 59637
THE GRANT (MUMBAI) : 59638 – 59640
THE GRANT (CHENNAI)
: 59641 – 59647
THE GRANT (KOLKATA)
: 59648 – 59650
INTRODUCTION TO DESIGN PUBLICATION : 59651
THE DESIGNS ACT 2000 SECTION 30 DESIGN
ASSIGNMENT
: 59652
COPYRIGHT PUBLICATION : 59653
REGISTRATION OF DESIGNS : 59654 - 59715

THE PATENT OFFICE
KOLKATA, 30/10/2015
Address of the Patent Offices/Jurisdictions
The following are addresses of all the Patent Offices located at different places having their Territorial
Jurisdiction on a Zonal basis as shown below:-
1 Office of the Controller General of Patents,
Designs & Trade Marks,
Boudhik Sampada Bhavan,
Near Antop Hill Post Office,S.M.Road,Antop Hill,
Mumbai – 400 037
Phone: (91)(22) 24123311,
Fax : (91)(22) 24123322
E-mail: cgpdtm@nic.in
4 The Patent Office,
Government of India,
Intellectual Property Rights Building,
G.S.T. Road, Guindy,
Chennai – 600 032.
Phone: (91)(44) 2250 2081-84
Fax : (91)(44) 2250 2066
E-mail: chennai-patent@nic.in
 The States of Andhra Pradesh,
Telangana, Karnataka, Kerala, Tamil
Nadu and the Union Territories of
Puducherry and Lakshadweep.
Near Antop Hill Post Office,S.M.Road,Antop Hill,
Mumbai – 400 037
Phone: (91)(22) 24137701
Fax: (91)(22) 24130387
E-mail: mumbai-patent@nic.in
 The States of Gujarat, Maharashtra, Madhya
Pradesh, Goa and Chhattisgarh and the Union
Territories of Daman and Diu & Dadra and Nagar
Haveli
5 The Patent Office (Head Office),
CP-2, Sector –V, Salt Lake City,
Kolkata- 700 091
Phone: (91)(33) 2367 1943/44/45/46/87
Fax: (91)(33) 2367 1988
E-Mail: kolkata-patent@nic.in
 Rest of India
Plot No. 32., Sector-14, Dwarka,
New Delhi – 110075
Phone: (91)(11) 2808 1921 – 25
Fax: (91)(11) 2808 1920 & 2808 1940
E.mail: delhi-patent@nic.in
 The States of Haryana, Himachal Pradesh, Jammu
and Kashmir, Punjab, Rajasthan, Uttar Pradesh,
Uttaranchal, Delhi and the Union Territory of
Chandigarh.
Website: www.ipindia.nic.in
www.patentoffice.nic.in
All applications, notices, statements or other documents or any fees required by the Patents Act, 1970
and The Patents (Amendment) Act, 2005 or by the Patents (Amendment) Rules, 2006 will be received
only at the appropriate offices of the Patent Office.
Fees: The Fees may either be paid in cash or may be sent by Bank Draft or Cheques payable to the Controller of
Patents drawn on a scheduled Bank at the place where the appropriate office is situated.

पेटेंट कार्ाालर्
कोलकाता, दिर्ांक 30/10/2015
•कार्ाालर्ों के क्षेत्राधिकार के पते
ववभिन्र् जर्हों पर स्थित पेटेंट कार्ाालर् के पते आंचभलक आिार पर िभशात उर्के प्रािेभशक अधिकार क्षेत्र के
साि र्ीचे दिए र्ए है:-
1 कार्ाालर् : महानर्र्ंत्रक, एकथव, अभिकल्प
तिा व्र्ापार धचहर्,
एंटोप दहल डाकघर के समीप,
एस. एम. रोड, एंटोप दहल, मुम्बई- 400 037, िारत,
फोर्: (91) (22) 24123311
फ़ै क्स: (91) (22) 24123322
ई. मेल: cgpdtm@nic.in
4 पेटेंट कार्ाालर्, िारत सरकार
इंटेलेक्चुअल प्रॉपटी राइट्स बबस्ल्डंर्, इंडस्थिर्ल इथटेट
एसआईडीसीओ आरएमडी र्ोडाउर् एररर्ा
एडजसेन्ट टु ईर्ल फ्लाथक, जी. एस. टी. रोड, र्ार्न्डी
चेन्र्ई - 600 032.
फोर्: (91)(44) 2250 2081-84
फ़ै क्स: (91)(44) 2250-2066
ई. मेल: chennai-patent@nic.in
 आन्र प्रिेश, तेलंर्ार्ा, कर्ााटक, के रल, तभमलर्ाडु
तिा पुडुचेरी राज्र् क्षेत्र एवं संघ शाभसत क्षेत्र, लक्षिीप
बौविक संपिा िवर्,
एंटोप दहल डाकघर के समीप,
एस. एम. रोड, एंटोप दहल, मुम्बई- 400 037,
फोर्: (91) (22) 24137701
फ़ै क्स: (91) (22) 24130387
ई. मेल: Mumbai-patent@nic.in
 •र्ुजरात, महाराष्ट्ि, मध्र् प्रिेश, र्ोवा तिा छत्तीसर्ढ़ राज्र् क्षेत्र एवं संघ शाभसत क्षेत्र,
िमर् तिा िीव, िािर और र्र्र हवेली.
कोलकाता, (प्रिार् कार्ाालर्)
सीपी-2, सेक्टर- V, साल्ट लेक भसटी,
कोलकाता-700 091, िारत.
फोर्: (91)(33) 2367 1943/44/45/46/87
फ़ै क्स:/Fax: (91)(33) 2367 1988
ई. मेल: kolkata-patent@nic.in
 िारत का अवशेष क्षेत्र
प्लॉट सं. 32, सेक्टर- 14, द्वारका, र्ई दिल्ली- 110 075.
फोर्: (91)(11) 2808 1921-25
फ़ै क्स: (91)(11) 2808 1920, 2808 1940
ई. मेल: delhi-patent@nic.in
हररर्ाणा, दहमाचल प्रिेश, जम्मू तिा कश्मीर, पंजाब,राजथिार्,
उत्तर प्रिेश, दिल्ली तिा उत्तरांचल राज्र् क्षेत्रों, एवं संघ शाभसत
क्षेत्र चंडीर्ढ़
वेबसाइट: http://www.ipindia.nic.in
www.patentoffice.nic.in
पेटेंट अधिनर्र्म, 1970 तिा पेटेंट (संशोिर्) अधिनर्र्म, 2005 अिवा पेटेंट (संशोिर्) नर्र्म, 2006 द्वारा वांनछत सिी आवेिर्,
सूचर्ाए, वववरण र्ा अन्र् िथतावेज़ र्ा कोई शुल्क पेटेंट कार्ाालर् के के वल उपर्ुक्त कार्ाालर् में थवीकृ त होंर्े।
शुल्क: शुल्क र्ा तो र्र्ि रूप में र्ा Controller of Patents के र्ाम में िेर् बैंक ड्राफ्ट र्ा चेक के द्वारा िेजी जा सकती है जो उसी थिार् के
ककसी अर्ुसूधचत बैंक में प्रित्त हो जहााँ उपर्ुक्त कार्ाालर् स्थित है ।

SPECIAL NOTICE
18 Months publication as required under Section 11A of the Patents Act, 1970
as amended by the Patents (Amendment) Act, 2005.
Notice is hereby given that any person at any time before the grant of Patent may give representation by way of
opposition to the Controller of Patents at appropriate office on the ground and in a manner specified under
section 25(1) of the Patents (Amendment) Act, 2005 read with Rule 55 of the Patents (Amendment) Rules,
2006.
Notice is also given that if any interested person requests for copies of the complete specification, drawing and
abstract of any application already published, the photocopy of the same can be supplied by the Patent Office as
per the jurisdiction on payment of prescribed fees of Rs.8/- per page. If any further details are required to be
obtained, the same can be provided by the respective Patent Offices on request.
( Rajiv Aggarwal )
CONTROLLER GENERAL OF PATENTS, DESIGNS & TRADE MARKS

SPECIAL NOTICE
Under the new provision of the Patents Act, 1970 as amended by the Patents (Amendment) Act, 2005
and Rules there under, Publication of the matter relating to Patents in the Official Gazette of India Part III,
Section 2 has been discontinued and instead The Official Journal of the Patent Office is being published
containing all the activities of The Patent Office such as publication of all the patent applications after 18th
months , grant of patents & all other information in respect of the proceedings as required under the provisions
of the Patents (Amendment) Act, 2005 and Rules thereunder on weekly basis on every Friday.
The Journal is uploaded in the website every Friday. So Paper form and CD-ROM form of the Journal are
discontinued from 01/01/2009.
SPECIAL NOTICE
Every effort is being taken to publish all the patent applications under section 11(A) of the Patents Act.
However, if duplication of publication of any application is found, then earlier date of publication will be taken
for the purpose of provisional protection for applicant and Patent Office will grant Patent not before six months
from the date of second publication, provided that there is there is no third party representation.

Early Publication:
The following patent applications have been published under section 11A (2) of The Patents (Amendment) Act 2005 and rule
24A of The Patents (Amendment) Rules, 2006. Any person may file representation by way of opposition to the Controller of
Patents at the appropriate office against the grant of the patent in the prescribed manner under section 25(1) of the Patents
(Amendment) Act 2005 read with the rule 55 of The Patents (Amendment) Rules, 2006:
(12) PATENT APPLICATION PUBLICATION (21) Application No.9637/DELNP/2015 A
(19) INDIA
(22) Date of filing of Application :14/10/2015 (43) Publication Date : 30/10/2015
(54) Title of the invention : METHOD FOR PRODUCING FURFURAL
(51) International classification :C07D307/50,C07D307/44
(31) Priority Document No :2014045277
(32) Priority Date :07/03/2014
(33) Name of priority country :Japan
(86) International Application No
Filing Date
:PCT/JP2015/055987
:27/02/2015
(87) International Publication No :WO 2015/133413
(61) Patent of Addition to Application
Number
Filing Date
:NA
:NA
(62) Divisional to Application Number
Filing Date
:NA
:NA
(71)Name of Applicant :
1)KAO CORPORATION
Address of Applicant :14- 10, Nihonbashi Kayabacho 1-
chome, Chuo- ku ,Tokyo 1038210 Japan
(72)Name of Inventor :
1)TAKABE Kenichi
2)NISHI Takafumi
(57) Abstract :
Provided are: a method for producing furfural by bringing superheated steam into contact with biomass feedstock including
hemicellulose obtained by bringing an acid catalyst and a wet agent comprising at least one of a surfactant , an aliphatic alcohol , a
multivalent alcohol and an aromatic alcohol into contact with one another; and a method for producing furfuryl alcohol by producing
furfural according to the aforementioned production method and then hydrogenating the furfural.
No. of Pages : 39 No. of Claims : 15

(12) PATENT APPLICATION PUBLICATION (21) Application No.3279/DEL/2015 A
(19) INDIA
(54) Title of the invention : EVA SOFT GRIP
(51) International classification :B62K21/26
(31) Priority Document No :NA
(32) Priority Date :NA
(33) Name of priority country :NA
Filing Date
:NA
:NA
(87) International Publication No : NA
(61) Patent of Addition to Application Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)ATUL THAKRAL
Address of Applicant :WZ 181/A, GALI NO. 3, SHRI
NAGAR, DELHI-110034 Delhi India
1)ATUL THAKRAL
(57) Abstract :
We have developed EVA soft grip without joint for bikes, scooters, motorbikes tow wheeler and all type of three wheeler, sports
goods and medical equipment etc.

(19) INDIA
(54) Title of the invention : ROTARY CAM TYPE RECLINER
(51) International classification :B60N2/235
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)KRISHNA MARUTI LIMITED
Address of Applicant :B-5, CHIRAG ENCLAVE, NEW
DELHI Delhi India
1)ASHOK KAPUR
(57) Abstract :
We claim that the present invention relates to Seat Recliners, which are mainly used in the Seats of Automobiles. Seat Recliner is a
mechanism which allows the driver and co-driver to adjust the position of seating system, by positioning of Seat Back (Angular
Adjustment) with respect to Seat Cushion. The present invention provides the reclining devices in Seating System by providing lesser
consumption of materials, low cost, compact size & lesser weight designing solution with increase in the static strength of reclining
device. At present, there are many type of reclining devices being used in Automobiles which are solving different purpose and utility.

(19) INDIA
(54) Title of the invention : CHAIR-TABLE FURNITURE
(51) International classification :A47C3/20
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Vinod Kumar Gupta
Address of Applicant :G4 Masjid Moth, Greater Kailash 2,
New Delhi-110048, India Delhi India
1)Vinod Kumar Gupta
(57) Abstract :
A Chair/table set combined in a flexible manner. The Chair and Table are configured to have independent bases, with an arrangement
to couple the base in a flexible manner so as to maintain the independent structure if desired by decoupling the bases. The Chair table
set can be used in class rooms and lecture rooms.

(19) INDIA
(54) Title of the invention : ABSORBENT ARTICLE
(51) International
classification
:A61F13/15,A61F13/49,A61F13/496
(31) Priority Document No :2013152528
(33) Name of priority
country
:Japan
(86) International
Application No
Filing Date
:PCT/JP2014/067884
:04/07/2014
(87) International
Publication No
:WO 2014/192981
(61) Patent of Addition to
Application Number
Filing Date
:NA
:NA
(62) Divisional to
Application Number
Filing Date
:NA
:NA
1)UNICHARM CORPORATION
Address of Applicant :182, Kinseichoshimobun ,Shikokuchuo
-shi ,Ehime 799-0111 Japan
1)SAITO, Kyota
2)PICHADKITJAWAT, Sarinee
3)BUNROD ,Natthakarn
4)CHANGCHAROEN, Jirapa
(57) Abstract :
This absorbent article with a waist opening and leg openings has: an absorbent body; an abdominal- side band member affixed so as to
overlap one end of the absorbent body in the vertical direction; and a back -side band member affixed so as to overlap the other end of
the absorbent body in the vertical direction, wherein the abdominal -side band member is connected to the back -side band member at
both ends in the horizontal direction. The length in the vertical direction of an overlapping section in which the abdominal- side band
member overlaps the absorbent body is longer than the length in the vertical direction of an overlapping section in which the back-
side band member overlaps the absorbent body. The abdominal s-ide band member has abdominal- side continuous elastic members
disposed continuously from one end to the other end in the horizontal direction, and abdominal- side discontinuous elastic members
disposed discontinuously in the horizontal direction. The back- side band member has back- side continuous elastic members disposed
continuously from one end to the other end in the horizontal direction, and back- side discontinuous elastic members disposed
discontinuously in the horizontal direction. The sum total of the contractive force of the back -side continuous elastic members is
greater than the sum total of the contractive force of the abdominal side continuous elastic members.

(19) INDIA
(54) Title of the invention : INTRAVENOUS CATHETER WITH A SECURED MECHANISM TO AVOID REVERSE FLOW OF
THE BLOOD
(51) International classification :A61M39/02
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)NEERAJ GUPTA
Address of Applicant :110-111, PHASE IV, UDYOG VIHAR,
GURGAON 122015 Haryana India
1)NEERAJ GUPTA
(57) Abstract :
The present invention provides an intravenous catheter with a secured mechanism for prevention of reverse flow of blood. The
mechanism consists of a one way valve with slit or groove in its convex portion that is securely inserted within the catheter hub. The
construction of one way valve allows flow of fluid in only one direction with the help of gravity infusion pressure and prevents flow
of fluid in the opposite direction.

(19) INDIA
(54) Title of the invention : ENGINEERED LIVER TISSUES , ARRAYS THEREOF , AND METHODS OF MAKING THE SAME
(51) International classification :C12N5/071,A61K35/407
(31) Priority Document No :13/841430
(33) Name of priority country :U.S.A.
Filing Date
:PCT/US2014/026679
:13/03/2014
(87) International Publication No :WO 2014/151921
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)ORGANOVO, INC.
Address of Applicant :6275 Nancy Ridge Dr., Suite 110, San
Diego ,CA 92121 U.S.A.
1)SHEPHERD, Benjamin, R.
2)ROBBINS ,Justin, B.
3)GORGEN, Vivian ,A.
4)PRESNELL, Sharon, C.
(57) Abstract :
Engineered living , three- dimensional liver tissue constructs comprising: one or more layers, wherein each layer contains one or more
liver cell types , the one or more layers cohered to form a living, three- dimensional liver tissue construct. In some embodiments , the
constructs are characterized by having at least one of: at least one layer comprising a plurality of cell types the cell types spatially
arranged relative to each other to create a planar geometry; and a plurality of layers , at least one layer compositionally or
architecturally distinct from at least one other layer to create a laminar geometry. Also disclosed are arrays and methods of making the
same. Also disclosed are engineered , living ,three- dimensional liver tissue constructs for use in the augmentation or restoration of
one or more liver functions by in vivo delivery of tissue or utilization of tissue in an extracorporeal device.

(12) PATENT APPLICATION PUBLICATION (21) Application No.3393/MUM/2014 A
(19) INDIA
(54) Title of the invention : REVEAL HIDDEN WITH I MICRO.
(51) International classification :G06F3/0481, G06F17/30
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)VIMAL PUMPOSH
Address of Applicant :R.H 8, SUNSHREE, WOODS NIBM
ROAD, KONDHWA, PUNE-411048, MAHARASHTRA,
Maharashtra India
1)VIMAL PUMPOSH
(57) Abstract :

(19) INDIA
(54) Title of the invention : SYNTHESIS OF NOVEL BIOLOGICALLY ACTIVE MIXED LIGAND YTTRIUM(III) COMPLEXES
(51) International classification
:C07F
5/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)SUNIL SUDAM PATIL
Address of Applicant :DEPARTMENT OF CHEMISTRY
CHANGU KANA THAKUR ARTS COMMERCE & SCIENCE
COLLEGE NEW PANVEL PLOT NO-01,SECTOR-
11,KHANDA COLONY,NEW PANVEL(W)DIST RAIGAD
MAHARASHTRA-410206 Maharashtra India
1)SUNIL SUDAM PATIL
2)GANESH ANANT THAKUR
3)ANIRUDDHA BALKRISHNA PATIL
4)AKALPITA SHASHANK BODKHE
5)MINAKSHI NARENDRAKUMAR GURAV
6)BHUSHAN PRABHAKAR LANGI
7)SANJAY KALURAM PATIL
8)HRUSHIKESH PRABHAKAR DEOKAR
(57) Abstract :
Present invention reports synthesis of biologically active mixed ligand Yttrium(III) complexes from Yttrium(III) chloride, 8-
hydroxyquinoline (HQ) and N and / or O donor amino acids (HL) such as L-threonine, L-proline, L-hydroxyproline, L-isoleucine and
L-serine. The method comprises conversion of Yttrium(III) chloride precursors to desired complexes using 8-hydroxyquinoline (HQ)
as primary ligand (HQ) and amino acids (HL) as secondary ligands (HL) in 1:2:1 proportion. The synthesized mixed ligand
Yttrium(III) complexes are novel as they are reported first time. The prepared complexes show excellent biological and germination
activity.

(19) INDIA
(54) Title of the invention : AUTOMATED SHOPPING CART-CARRETILLA 1
:B62B
3/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)HARISH RAJURKAR
Address of Applicant :ST. VINCENT PALLOTTI COLLEGE
OF ENGINEERING & TECHNOLOGY,GAVASI MANAPUR
NAGPUR, MAHARASHTRA, INDIA. Maharashtra India
1)HARISH V. RAJURKAR
2)CHANCHAL TOMER
3)JANHAVI JOSHI
4)KRIPA DESAI
5)ROWENA SALDANHA
6)AKASH WANKHADE
7)PRAFUL THOMBARE
(57) Abstract :
The automated shopping cart mainly consist of four major parts namely LCD circuit, laser circuit, barcode scanner and lock
mechanism. Laser circuit is used here for antitheft purpose. In addition to theses circuits trolley has special slider mechanism for
tacking in products automatically .On LCD screen itself the information of product like name, price and quantity are displayed.
Trolley is equipped with free scanner to scan from any direction. The door mechanism has employed a servo motor which is pre
programmed for performing the locking and unlocking action. The slider system opens and closes up with the help of gate switches
and DC Motor installed underneath it. Apart from this, the trolley has a heart PCB of micro controller to which entire circuitry is
interface. The especially build door can only be closed and opened with privately authorised barcode of admin (any authorized person
or employee).

(19) INDIA
(54) Title of the invention : A GAS-SOLID SEPARATOR AND A PROCESS FOR GAS-SOLID SEPARATION
(51) International classification :C10G11/18
Filing Date
:PCT//
:01/01/1900
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)RELIANCE INDUSTRIES LIMITED
Address of Applicant :3rd Floor, Maker Chamber-IV 222,
Nariman Point, Mumbai-400021, Maharashtra, India Maharashtra
India
1)GUNJAL PRASHANT RAMCHANDRA
2)MISHRA VED PRAKASH
3)KATTI SANJEEV SHRINIWAS
(57) Abstract :
A gas-solid separator comprises a housing comprises an inlet conduit configured to receive a gas-solid mixture. The inlet conduit
extends in an operative downward direction inside the housing. The gas-solid separator further comprises a first outlet conduit
configured to discharge cleaned gas containing minute amounts of solid particles and a second outlet conduit configured to evacuate
solid particles collected in the housing. The gas-solid separator also comprises a plurality of axial swirl cone cyclones. The axial swirl
cone cyclone has a cyclone body having a cylindrical portion that forms a swirl zone and a conical portion extending coaxially from
the cylindrical portion that forms a vortex zone. The axial swirl cone cyclone comprises a feed inlet, a cleaned gas outlet disposed, and
swirl imparters. A process for gas-solid separation is also disclosed in the present disclosure. Fig.1

(19) INDIA
(54) Title of the invention : NOVEL ANHYDROUS CRYSTALLINE FORM OF REGADENOSON AND PROCESS FOR
PREPARATION THEREOF
:C07D
213/00,C07H19/167
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)SKVEN TECHONOLOGIES PRIVATE LIMITED
Address of Applicant :1004 IRIS KESAR GARDEN
SECTOR-20 KHARGHAR NAVI MUMBAI 410210
MAHARASHTRA Maharashtra India
1)NAVEEN REDDY K
2)RANJITH.S
(57) Abstract :
The present invention relates to a novel anhydrous polymorph of Regadenoson of formula (1) and process for the preparation and its
methods of isolation which is used for the large scale preparation.

(19) INDIA
(54) Title of the invention : A NEW TECHNIQUE FOR ELECTRICITY GENERATION ON MOVING PASSENGER
VEHICLES/TRAINS
:H02K21/22,H02K
7/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)JAI SHANKAR SINGH
Address of Applicant :C-1/301, MERIDIAN, AAKRITI ECO-
CITY, BHOPAL-462 039 Madhya Pradesh India
1)JAI SHANKAR SINGH
2)RAJENDRA SINGH GAHLOT
3)JITENDRA JATAV
4)JAGDISH PRASAD
(57) Abstract :
The present invention relates to generation of electricity during movement of passenger vehicles/trains by converting the experienced
air impact into rotation of an alternator. This has been achieved by installing an alternator on the top of the vehicle in its front portion
and attaching an angular fan blade on the alternator shaft so that it can move freely. During movement of the vehicle, the air impact on
the blades enables rotation of the alternator and results in generation of electricity which can meet the electrical needs of the moving
passenger vehicles/trains coaches as well as increase the efficiency of electrical driven vehicles. The technique is able to generate
electricity with the help of surrounding air which is a renewable source with abundant supply. So, the technique provides huge
economic and environmental benefits and also opens the doors for many researchers relating to its future uses.

(19) INDIA
(54) Title of the invention : SPY PENTACOPTER
:B64F
1/00,
B64C
27/04
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)PRAKASH TARUN KUMAR
Address of Applicant :1104, PRIYA TOWER, PLOT NO.144,
SECTOR 19, KHARGHAR, NAVI MUMBAI 410210
Maharashtra India
1)PRAKASH TARUN KUMAR
(57) Abstract :
Spy Pentacopter consist of 5 rotors designed for speed, swiftness and long range of operation. These 5 rotors are connected to 5
independent motors for better efficiency and power. Each rotor has 4 blades with aerodynamic designs for better functionality. This
Pentacopter has ability to attach a spy camera at the base and can be controlled from local command center using a computer. Also it
has two stability wings with basic ammunition to temporarily paralyze the target. There are four drawings to illustrate the design of the
helicopter.

(19) INDIA
(54) Title of the invention : BANNER TARGET TOWING (BTT) ON FIGHTER AIRCRAFT FOR PILOT GUNNERY TRAINING
WITH REHEAT AND TAKE OFF - BTT CABLE DESIGN WITH WEAK LINK AND SHEAR PIN
(51) International classification :B64C99/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AIRCRAFT UPGRADE RESEARCH & DESIGN
CENTRE (AURDC)
Address of Applicant :HINDUSTAN AERONAUTICS
LIMITED, NASIK DIVISION, OJHAR TOWNSHIP POST
OFFICE, OJHAR (MIG), NASIK-422207 MAHARASHTRA,
INDIA Maharashtra India
1)SHARAD KASHINATH BARVE
2)SUNIL KUMAR DWIVEDI
(57) Abstract :
Banner Target Towing (BTT) is deployed as a target on fighter aircraft for pilot gunnery training. The present BTT are deployed from
fighter aircraft without reheat take off. With this the takeoff run of the aircraft is too long and is restriction in case runway length is
less. This invention is design of a BTT system that caters for reheat takeoff of the aircraft, thereby reducing the takeoff run. The
purpose of designing of BTT for reheat takeoff was to facilitate with BTT for gunnery training of the pilots. The design facilitates
utilization of the BTT with short takeoff run. The studies / analysis were carried out for design & development of BTT for reheat take
off feasibility study / analysis of BTT system and its operation, preliminary design of the BTT cable with weak link and shear pin,
detail design, qualification testing for the breaking load of the shear pin and the complete cable assembly, Flight Trials with reheat
take off to assess the performance, shearing of the weak link shear pin and jettisoning of BTT in case of landing /emergency.

(19) INDIA
(54) Title of the invention : ELECTRONICALLY TUNABLE THIRD-ORDER SWITCHED-CAPACITOR FILTER
CONFIGURATION WITH FEED FORWARD SIGNAL TO MINIMIZE OVERSHOOT
:H01G
9/00,
H03H
11/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR.SHINDE GANESHCHANDRA NARHARRAO
Address of Applicant :9 GANGA NIWAS, HANUMAN
NAGAR, TILAKNAGAR ROAD, NANDED 431 605 MAH.
Maharashtra India
(57) Abstract :
The present invention concerns the method for designed & implementation of an Electronically Tunable Third-Order Switched-
Capacitor Filter Configuration with Feed forward Signal to minimize Overshoot. The invented circuit discusses a new configuration to
realize third-order with three filter functions low pass, band pass, and high pass simultaneously in single circuit. The response of
circuit is designed and studied for different circuit merit factor Q and different Center frequency fo. The filter circuit can be used for
both narrow as well as for wide bandwidth. Thus, this circuit works for electronically tunable bandwidth. The gain roll-off for this
circuit is close to the ideal value of 18 dB / octave (40dB/ decade) as for third order filters. In the invented circuit configuration, the
peak gain for overshoot is minimizing from 44dB to 5dB due to the feed forward input signal for low pass filter. This filter
configuration shows better response for Q > 0.4. Also, stabilization of gain for High pass filter function can be achieved at OdB for
Q>0.4. The Low pass filter function works practically only for higher merit factor Q. The circuit shows better response for Q > 0.4
and fo =15 kHz. The circuit works properly for higher center frequencies when fo >20 KHz. Also, the Stabilization of gain for High
pass function can be achieved at OdB for fo <60 KHz.The Low pass filter function works practically only for higher center
frequencies. The advantages of this invention circuit are the reduction in size and weight, the increase of circuit reliability, filter with
dynamic high range and it is more economical and easier for manufacturing. Also, to provide an extension electronic filter apparatus
for different analog components such as used in measurement instruments, sampled data transmission or communication system.

(19) INDIA
(54) Title of the invention : CONTINUOUS FILTER
:A61K31/24,
A61P37/09
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)ARUN DADDA
Address of Applicant :ROW HOUSE # 76, HILL GARDEN,
TIKUJINIWADI ROAD, MANPADA, THANE (W)-400607
Maharashtra India
1)ARUN DADDA
(57) Abstract :
This invention refers to a continuous dual filter that helps in the separation of sediments from the floating products by using a double
filter, namely a perforated mesh in one compartment and a bucket filter in the other

(19) INDIA
(54) Title of the invention : TURNING ROUTER IN TO WEB SERVER
:H04L
29/00,H04L12/701,
H04L12/24
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)MR.HIREN S.DHUVAD
Address of Applicant :504, AFSHA ENCLAVE, SWAMI
SATYANAND MARG, B/H MAXUS MALL LANE,
BHAYANDER (W), 400 706, MAHARASHTRA, INDIA.
Maharashtra India
2)MRS.JINAL H. DHUVAD
1)MR.HIREN S.DHUVAD
2)MRS JINAL H.DHUVAD
(57) Abstract :
The present invention disclosed an approach which can simplify the process or allows sharing content on web server without using
internet.

(19) INDIA
(54) Title of the invention : DEVELOPMENT OF AN OPTIMIZED DESIGN METHODOLOGY & SYNTHESIS FOR STABILITY
OF 3RD -POLE CURRENT-MODE ACTIVE- R FILTER USING FEED FORWARD SIGNAL
:G01P
15/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Address of Applicant :9-GANGA NIWAS,
HANUMANNAGAR, TILAKNAGAR ROAD, NANDED-431
605, MAHARASHTRA, INDIA. Maharashtra India
(57) Abstract :
The study proposes development of an optimized design methodology & synthesis for stability of 3 rd-pole current-mode active-R
filter for =20 KHz and Q-factor =1 with Feed forward Signal to realize the stability of circuit. This invention illustrates a new
configuration to realize the stability of 3 rd-pole current-mode active-R filter. The proposed circuit implements three transfer functions
low-pass, band-pass, and high-pass concurrently in single circuit with work at different nodes with gratified results. It observed that,
all poles of transfer functions have negative real parts, and they are lying within the left-half of the s-plane. All poles of transfer
functions are at (-1.26105), and (-6.28xl0A4±jl.09xl0A5). The return ratio of Nyquist diagram does not enclose the critical point (-1,
0) for all transfer functions. The gain (Gm) and phase (pj margins are both positive. Thus the closed-loop for all transfer functions of 3
rd-pole current-mode active-R filter at different nodes are asymptotically stable. This filter is stable for 1Hz < f >1449 KHz for Q-
factor = 1. The output and input gains are identical at gain cross over frequency. The benefits of this filter are the reducing in weight
and size, increasing of circuit quality with wide range for frequency, and it is easier and more economical for producing.

(19) INDIA
(54) Title of the invention : AN IMPROVED WATER FILTER
(51) International classification :B01D24/10, B01D24/02,
Filing Date
:NA
:NA
Number
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DIWAKAR DEY
Address of Applicant :STATION PARA WARD NO.9,
RAJNANDGAON, STATE OF CHHATTISGARH Chattisgarh
India
1)DIWAKAR DEY
(57) Abstract :

(19) INDIA
(54) Title of the invention : MICRO-CHANNEL HEAT-EXCHANGER INSPIRED BY LEAF-VENATION FOR ELECTRONIC
COOLING
:H01L
23/00,
H01L21/56,
H01L23/427
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Suhas Sakharam Mohite
Address of Applicant :H.O. D, Department of mechanical
engineering, Government College of Engineering, Karad, PIN -
415124 Maharashtra India
1)Suhas Sakharam Mohite
2)Vinayak P. Gaikwad
(57) Abstract :
Micro-channel heat sink based on leaf venation pattern are designed and fabricated to remove the limitations of conventional parallel
micro-channel heat sink. Micro-channels are fabricated on back side of silicon wafer, while electronic circuits are created on the front
side. The leaf venation pattern reduces the high temperature gradient along the length of the heat sink. Lowest values of thermal
resistance are encountered due to the fabrication of heat sink on a silicon substrate, thus removing more heat from the region.
Following invention is described in detail with the help of Figure 1 of sheet 1 showing the isometric view of micro-channel heat sink
and Figure 2 of sheet 2 showing the top view of the micro-channel heat sink.

(19) INDIA
(54) Title of the invention : AN ENHANCED SECRET DATA HIDING MECHANISM IN MASTER COLOR COMPONENT OF
PIXEL BY USING VIRTUAL REPLACEMENT KEY METHOD
:H04L
9/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Prof. Mahip Bartere
Address of Applicant :C/o Sunil B.Dahele Chetandas Bagicha,
Masanganj, near Nagarsevak SahSahu House, Amravati.
Maharashtra India
2)Dr. Hemant Deshmukh
1)Prof. Mahip Bartere
2)Dr. Hemant Deshmukh
(57) Abstract :
Present invention provides specially an enhanced secret data hiding mechanism in master color component of pixel by using virtual
replacement key method. The existing stenographic methods can be measured from its parameters like transparency, quality, data
hiding capacity, PSNR, MSE etc. Existing methods are lacking in data hiding capacity and this is our main motto to increase data
hiding capacity up to infinity level. It provides security to hidden message from unauthorized accesses. The proposed algorithm
performed evaluation in terms of embed ability criterion, computational cost, computational time, hiding capacity etc. To maintain
Image Perceptual quality it is necessary that to avoid suspicion the embedding should occur without significant degradation or loss of
perceptual quality of the cover media. In the proposed methodology, our concept will achieve huge data hiding capacity irrespective of
carrier size. This may lead to an enhance technology in an era of secure data transmission. Following invention is described in detail
with the help of Figure 1 of sheet 1 showing data flow diagram of proposed method.

(19) INDIA
(54) Title of the invention : Synthesis and study of bio-erodable material using low density polyethylene and polyethylene glycol
(51) International classification :A61F 2/00
Filing Date
:PCT//
:01/01/1900
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Vijaya Sangawar
Address of Applicant :Polymer Research Laboratory,
G.V.I.S.H. Amravati (M.S.) INDIA Maharashtra India
2)Amit Gadre
3)Ganesh Yerawar
1)Vijaya Sangawar
2)Amit Gadre
3)Ganesh Yerawar
(57) Abstract :
ABSTRACT The present invention relates to a method of synthesis of bio-degradable plasticmaterial by using a PEG (Polyethylene
glycol) + LDPE (Low density polyethylene). Following invention is described in detail with the help of Figure 1 of sheet 1 shows the
graph of XRD of LP5P0, Figure 2 of sheet 1 shows the graph of XRD of LP5P9, Figure 3 of sheet 2 shows the graph of XRD of
LP5P12, Figure 4 of sheet 2 shows the graph of XRD of LP5P18, Figure 5 of sheet 3 shows the graph of FTIR of LP5P0, Figure 6 of
sheet 3 shows the graph of FTIR of LP5P9, Figure 7 of sheet 4 shows the graph of FTIR of LP5P12, Figure 8 of sheet 4 shows the
graph of FTIR of LP5P18, Figure 9 of sheet 5 shows the graph of UV-VIS spectrum of LP5P0, Figure 10 of sheet 5 shows the graph
of UV-VIS spectrum of LP5P9, Figure 11 of sheet 6 shows the graph of UV-VIS spectrum of LP5P12 and Figure 12 of sheet 6 shows
the graph of UV-VIS spectrum of LP5P18.

(19) INDIA
(54) Title of the invention : LITHIUM COMPLEX GREASE MANUFACTURING PROCESS
:C10M
117/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)STANDARD GREASES & SPECIALITIES PRIVATE
LIMITED.
Address of Applicant :101, KETAN APARTMENTS, 233, R.
B. MEHTA MARG, GHATKOPAR-EAST, MUMBAI-400 077,
MAHARASHTRA, INDIA. Maharashtra India
1)MR. VIJAY PRABHAKAR DESHMUKH
2)MR. BHUPENDRASING KOMALSING RAJPUT
(57) Abstract :
A process for manufacturing high dropping point lithium complex greases is developed using hydrogenated castor oil (HCO) as fat
and boron esters as complexing agents. The said process gives lithium complex greases with high dropping point and better
mechanical and roll stability.

(19) INDIA
(54) Title of the invention : TESTING OF WIND GENERATOR RESEARCH MODEL USING BICYLE AND GEAR BOX FOR
PREDICTION OF PERFORMANCE OF ONSITE WIND GENERATOR BEHAVIOUR
:F03D
11/00,
F03D1/02,
F03D9/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DATTA SAMPATRAO CHAVAN
Address of Applicant :AMRUT KAILASH NAGRI, C-203,
S.NO.34/13A, AMBEGAON BUDRUK, BEHIND BHARTI
VIDYAPEETH, KATRAJ, PUNE-411046, MAHARASHTRA,
INDIA. Maharashtra India
1)PARASHURAM BALWANT KARANDIKAR
2)KADAGANCHI NEHAL RAMESH
(57) Abstract :
Voltage flicker and other power quality parameter prediction is the major issue in site selection for wind power plant. Testing of the
wind generator in scaled down model to predict the voltage flicker and other power quality parameters is a new concept. In this
innovation bicycle is used as a prime mover for the scaled downed low capacity wind generator. The wind generator may be squirrel
cage induction generator, slip ring induction generator, synchronous generator or permanent magnet synchronous generator or any
other type. Electricity is saved in this research as no external electricity is used for testing the wind generator. The test set up can be
easily built as the mechanism is simple; the material required for the test set is also easily available. Moreover testing procedure is
very simple.

(19) INDIA
(54) Title of the invention : TEST SET UP STUDY IMPACT OF SURFACE ROUGHNESS ON VOLTAGE FLICKER INITIATED
IN WIND TURBINE RESEARCH MODEL.
:F03D
11/00,
F03D
1/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
VIDYAPEETH, KATRAJ, PUNE-411 046, MAHARASHTRA,
(57) Abstract :
Various surfaces like seashore and offshore surfaces can simulated in the test set up for studying the impact of that surface on power
quality parameters such as voltage flicker and may more. The main idea in this invention is that various types of surface roughness are
created in the wind turbine test set up. Wind turbine can be tested for various wind conditions and surface roughness on scaled down
basis. Results obtained can be scaled up to predict voltage flicker as well as other power quality parameters of wind turbine

(19) INDIA
(54) Title of the invention : POINT SOURCE OF AIR TO STUDY IMPACT OF VERTICAL SHEAR ON FLICKER INITIATED IN
WIND TURBINE RESEARCH MODEL
:F03D
1/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
VIDYAPEETH, KATRAJ, PUNE-411 046, MAHARASHTRA,
(57) Abstract :
Vertical and horizontal wind shear affects the performance of the wind generation. Power quality parameters such as output voltage,
output power, voltage flickers, frequency etc get affected. The invention is to create the facility to test impact of vertical / horizontal
wind shear more accurately. Two point sources of air are used in the test set up, to blow the air on the wind turbine blades at different
speeds to create the wind shear. The time required to produce the wind shear is less and wind shear can be controlled accurately.

(19) INDIA
(54) Title of the invention : EXPERIMENTAL SET UP FOR FLOW BOILING
:F28F
13/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Acharya Anil Ramchandra
Address of Applicant :Associate Professor, Heat Transfer
Laboratory, Mechanical Engineering Department, Govt. College
of Engineering, Karad 415124 Maharashtra India
2)Pise Ashok Tukaram
1)Acharya Anil Ramchandra
2)Pise Ashok Tukaram
(57) Abstract :
Present invention provides specially designed, developed and implements an experimental setup for flow boiling process. The present
invention relates to a novel instrument for enhanced heat transfer rate in flow boiling process. More particularly, the present invention
relates to a novel idea of tilting for various parameters. Especially in distillation process if this novel instrument is used, the heat
transfer rate enhancement at a particular tilt will ultimately reduce the time and energy required to complete the process. Saving in
time and energy is having impact on productivity and profit. Following invention is described in detail with the help of Figure 1 of
sheet 1 showing schematic diagram of flow boiling experimental set-up and Figure 2 of sheet 2 showing flow boiling setup for
studying flow boiling regimes .

(19) INDIA
(54) Title of the invention : METHOD FOR TREATING BIO-ORGANIC WASTE WATER SLUDGES AND OTHER ORGANIC
WASTE MATERIALS.
:C02F
3/00,
C02F
11/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)CERES BIOSYSTEMS LIMITED
Address of Applicant :229 NIAGARA STREET TORONTO
ONTARIO CANADA M6J2L5 Canada
1)JOHN ROBERT SAMPSON
2)KEVIN MICHAEL ANDREWS
(57) Abstract :
The present invention relates to a method of converting organic waste materials including bio-organic and/or wastewater sludges into
a soil amendment or fertilizer with a beneficial mix of macro and micro nutrients that can be used on agriculture land requiring an
amendment or fertilizer with a neutral pH. The invention is particularly useful in stabilizing the organic waste so that they can be
safely utilized in combination with other micro and macro nutrient additives.

(12) PATENT APPLICATION PUBLICATION (21) Application No.5335/CHE/2015 A
(19) INDIA
(54) Title of the invention : QUANTUM DOT INGRAINED AND DUAL MOTIF TETHERED ARTIFICIAL VIRUS LIKE
STRUCTURE FOR GENE DELIVERY
(51) International classification :c12N
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)NADACKAL BABY JOMON
Address of Applicant :NADACKAL (H), VALACHIRA,
KADUTHURUTHY P.O., KOTTAYAM - 686 604, Kerala India
1)NADACKAL BABY JOMON
2)DR. KANNISSERY PRAMOD
3)JOHN SYRI;
4)MOOTHEDATHU RAYNOLD AJI ALEX
5)DR.CHETTIYAM VEETTIL SUNEESH
6)DR.MEHER ALI ABU TAHIR
(57) Abstract :
Embodiments of the present invention report invention is related to an artificial virus like structure in the size range of 10-1000 nm for
delivering gene. Quantum dot is ingrained in the artificial virus like structure which is dual motif tethered. The structure consists of a
central core of citrate stabilized zinc oxide quantum dots capped with polyethyleneimine. To the core a covering of folic acid
conjugated albumin and DNA(gene)conjugated to cell penetrating peptide is given to form the artificial virus like structure.

(19) INDIA
(54) Title of the invention : A UHF RFID READER ANTENNA INTEGRATED WITH NEAR FIELD AND FARFIELD
OPERATIONS
(51) International classification :G01s
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)MALATHI KANAGASABAI
Address of Applicant :DEPARTMENT OF ELCTRONICS
AND COMMUNICATION ENGINEERING, ANNA
UNIVERSITY, CHENNAI - 600 025, Tamil Nadu India
2)JAYARAM K P
3)M.GULAM NABI ALSATH
2)JAYARAM K P
(57) Abstract :
The present invention relates to RFIDs (radio frequency, identification systems) employed for tracking and identification of objects
attached with RFID tags. The present invention is a multi service antenna serving both near filed and farfield RFID reader operation
requirements. The circular polarisation in the farfield is achieved by asymmetric perturbation in the slot radiator. The present
invention comprises of an L shaped feed used to feed the antenna, which gives impedance bandwidth of 12.6%. The circular
polarization in the farfield is achieved by employing asymmetric perturbation technique. The inductive coupled near field is generated
by two magnetic field generators viz. multiple ODC and an ODC element. The antenna is fabricated on single layered FR4 substrate.
The present invention provides strong and uniform magnetic field results in improved read range as well as the interrogation area for a
lesser input power.

(19) INDIA
(54) Title of the invention : A DEVICE AND METHOD FOR FABRICATION OF ULTRA-WIDE BAND MICROSTRIP GRID
ARRAY ANTENNA (GAA)
(51) International classification :G01S
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Address of Applicant :DEPARTMENT OF ELCTRONICS
AND COMMUNICATION ENGINEERING, ANNA
UNIVERSITY, CHENNAI - 600 025, Tamil Nadu India
3)LIVYA LAWRANCE
3)LIVYA LAWRANCE
(57) Abstract :
The present invention pertains to a means for minimizing the impact of pre-crash, collision avoidance and other safety relevant
applications in automotive radars. The Grid Array Antenna is developed to facilitate enhanced sensing range covering the 21.5 GHz-
26.5 GHz band with operating frequency centered at 24.5 GHz with reference VSWR < 2. The GAA consists of 33 radiating elements
and are excited using a common transmission line centre fed by a 50 Q coaxial probe. Furthermore, amplitude tapering techniques are
employed to lower the side lobe level. The radiation beam width (3dB) of the prototype is 10° and 92° in the azimuth and elevation
planes at 24 GHz. The developed amplitude-tapered GAA provides 2.5 GHz effective operational bandwidth with VSWR < 2 and gain
variation less than 3 dB. In addition, the miniaturized broadside radiator exhibits high gain across the operating band, low cross
polarization level and radiation efficiency of 96%, with a side lobe level of less than -15 dB measured at 24 GHz. The measured peak
gain is 13.87 dB at 24 GHz. The merits of wide bandwidth and required radiation characteristics of the linearly polarized GAA make it
a promising candidate for automotive radar technology.

(19) INDIA
(54) Title of the invention : AUXILLARY PROPULSION USING KITE/SAIL
(51) International classification :B63H
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AMET UNIVERSITY
Address of Applicant :135 EAST COAST ROAD,
KANATHUR - 603 112 Tamil Nadu India
1)DR. A.S. PERUMAL
2)DR. N. MANOHARAN
3)MRS. VIJAYALAKSHMI C.H
(57) Abstract :
This invention discloses a method of Introducing Renewable Energy for ship Propulsion. A performance study of auxiliary wind
propulsion by means of traction of kite is discussed. A theoretical study has been carried out as to how much fuel can be saved in
various environmental conditions. The auxillary propulsion using kite/sail results in thrust produced to pull the vessel in the forward
direction while also meeting with the IMO tier-II regulations for all new ships.

(19) INDIA
(54) Title of the invention : HYBRID ASH BRICKS AND METHOD OF PREPARATION
(51) International classification :C04B
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)K. VIDHYA
Address of Applicant :ASSOCIATE PROFESSOR IN CIVIL,
5/57, KAILASAMPALAYAM, VADUGAM POST,
RASIPURAM T.K., NAMAKKAL DISTRICT - 637 407 Tamil
Nadu India
2)DR. S. KANDASAMY
1)K. VIDHYA
2)DR. S. KANDASAMY
(57) Abstract :
Natural clay is the prime ingredient of conventional clay brick. For the manufacture of clay bricks, huge quantities of natural clay soil
are mined. Also, soil erosion is hastened. Thus precious land resources are affected. Moreover, moulded natural clay bricks are burnt
in kilns which use fire wood as fuel. A number of trees are cut down to collect firewood. This leads to deforestation which produces
adverse effects on the environment. Thermal power plants generate large volumes of coal ash collected as dry fly ash and wet pond
ash. The safe disposal of this material is a great concern. Fly ash finds some usefulness as an additive in the manufacture of cement,
bricks and blocks. But much attention has not been paid on the effective utilization of pond ash. The objective of this invention is to
develop a green building material namely HYBRID ASH BRICKS AND METHOD OF PREPARATION by utilizing both coal ashes,
bagasse ash with standard ingredients. These hybrid bricks can be used as units of brick masonry to construct load bearing walls and
infill walls. The mix proportions were designed. The hybrid ash bricks were manufactured. They were tested as individual brick units
as per Indian Standards. Due to enhancement in strength and other mechanical properties, reduction in manufacturing cost, utilization
of waste byproducts, hybrid ash bricks have evolved as an alternative sustainable green building material.

(19) INDIA
(54) Title of the invention : DEVICE: HUMAN VEIN IDENTIFIER
(51) International classification :A61B
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR.P.VINOD KUMAR,
Address of Applicant :70A, SARASWATHYVILASAM,
PALLIVILAI, VETTUNIMADAM, NAGERCOIL,
KANYAKUMARI DISTRICT, TAMIL NADU - 629 003 Tamil
Nadu India
1)DR.P.VINOD KUMAR,
2)P.PONRAM
3)B.C.ANISH KRISHNAN NAYAR
(57) Abstract :
■I ABSTRACT OF THE INVENTION This invention is useful for identify the vein on human body. This device has skin
illuminating light source, a magnifying glass to detail see the visible vein and hollow triangular structure which makes the skin
illuminated and curtailing external radiation. The principle behind the device is that when light is irradiated skin gets illuminated while
the vein absorbs it and appears to naked eye as small rivulet like pattern. Therefore contrasting colours are produced for the skin and
vein. This helps the medical personnel to identify the vein easily. FIG.2.

(19) INDIA
(54) Title of the invention : METHOD AND SYSTEM FOR SCHEDULING MEETINGS
(51) International classification :G06Q
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)WIPRO LIMITED
Address of Applicant :Doddakannelli, Sarjapur Road,
Bangalore 560035, Karnataka, India. Karnataka India
1)RAGHAVENDRA HOSABETTU
2)PARTHASARATHY ARMUGASAMY
3)KIRAN KUMAR C S
(57) Abstract :
The present subject matter relates to a method and a system for scheduling meetings. In an embodiment, the method comprises
receiving, by a meeting organizer system, meeting data and information about a plurality of registered participants. Then, a unified
view of one or more profiles of each of the registered participants is generated based on one or more predefined rules. Further, a
confidence score is determined for predicting success of the meeting organization based on at least one of the meeting data and
historical data of each of the registered participant. Then, meeting schedule is modified based on the confidence score. Finally, a
meeting invitation to a participant device associated to each of the registered participants based on the confidence score. FIG.4

(19) INDIA
(54) Title of the invention : BAND GAP SMOOTHENING IN PV STRING USING CONTROLLED SIMULATION OF
ELECTRONS BY INTERMITTENT ELECTROSTATIC GENERATION
(51) International classification :H01L
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AMET UNIVERSITY
Address of Applicant :135 East Coast Road, Kanathur 603
112. Tel : 044-27472155 Tamil Nadu India
1)Dr. D.Padma Subramanian
2)Jeby Thomas Jacob
3)M.Dheepak
(57) Abstract :
A novel method for band gap smoothening in PV string using High frequency floating pulse generator (HFPCG) is proposed utilizing
the principle of controlled stimulation of electrons by intermittent electrostatic generation. Solar Panel String Band Gap smoothening
method comprises of a HFPCG, Logic analyzer and controller to trigger HFPCG and data acquisition system. Triggering of HFPCG is
achieved by varying the duty cycle. Variation in duty cycle is performed through a control algorithm which involves a comparison of
measured values of irradiation, insolation and solar power generation with the ideal values. If the measured values do not match with
the ideal values, the HFPCG is triggered to produce a high frequency pulse which gives acceleration to the electrons which will result
in floating the electrons in the valence band to a level closer to conduction band. This in turn will help the low energy electrons to
cross the band gap. Thus by proper variation of duty cycle of HFPCG, band gap smoothening and hence enhancement solar plant
performance can be made.

(19) INDIA
(54) Title of the invention : THE METHODS OF CONSTRUCTING FLOATING BUILDINGS AND OTHER FLOATING
APPARATUS
(51) International classification :E04B
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)MUTHUPAIYAN MULLAIVALAVAN
Address of Applicant :LECTURER, DEPARTMENT OF
ARCHITECTURAL ASSISTANTSHIP, DR.DHARMAMBAL
GOVERNMENT POLYTECHNIC COLLEGE FOR WOMEN,
THARAMANI, CHENNAI - 600 113, Tamil Nadu India
2)VIJAYAN PONMALAR
1)MUTHUPAIYAN MULLAIVALAVAN
2)VIJAYAN PONMALAR
(57) Abstract :
The existing floating buildings and other floating apparatus have been made by creating air packets in.the constructions.Further, they
have also concentrated different material usage for constructing the same.In this invention an attempt was made for construction- of
floating building and other floating apparatus by incorporating or creating vacuum, in the construction or. by attaching many grouped
vacuum sources and its cumulative bulks on the respective buildings or in the apparatus. Hence, floating behavior of buildings or in
the apparatus can be achieved by three different methods. First method, Different sizes and shapes of hollow core created walls and
floors are filled partially by riieans of vacuum sources. Second method, by attaching many grouped vacuum sources . and. its
cumulative bulks on the buildings or in the apparatus. In combination of both 1 & 2 is it Ke third method In general; The Vacuum
packets can be created in two different methods. One is artificial: method and another one is Natural method. Creating Vacuum in the
floating construction will give, following significant advantages as compared with existing: Higher amount of load carrying per unit
volume of buildings space. It is very difficult for pushing the vacuum packets inside water, this will enhances the-safety of the
building. The requirement of quantity of vacuum heeded for constructing floating structures Is yery less Thecost irivolvedfofcreating
vacuum in the construction is very less. Theireforevithis-lecnniquejs most effective andeconomical one in the field of constructing
floating buildings or in the apparatus. On the whole, vacuum created in th structures of floating buildings, or in the apparatus is totally
new invention which is not extsts. Figure. 3

(19) INDIA
(54) Title of the invention : METHOD AND DEVICE FOR GENERATING PANORAMIC IMAGES WITH REAL-TIME
ANNOTATIONS
(51) International classification :G06F
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)WIPRO LIMITED
1)PRIYANSHU SHARMA
2)VIGNESH PRABU SINGANALLUR DHANDAPANI
3)KIRAN KUMAR CHANNARAYAPATNA
SATHYANARAYANA
(57) Abstract :
The present disclosure relates to a method for generating panoramic images with real-time annotations. In an embodiment, an image
annotation device is present within the computing device. The image annotation device receives a plurality of frames of an
environment and identifies one or more region of interest (ROI) in the plurality of frames. The image annotation device further
captures one or more annotations and sensory data with respect to the one or more ROI and combines each of the plurality of frames
along with the one or more annotations and sensory data to generate panoramic images with real-time annotations. Fig.2

(19) INDIA
(54) Title of the invention : GENERATION OF POWER ONBOARD SHIPS USING TUNNEL THRUSTERS/TURBINES
(51) International classification :B63B
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AMET UNIVERSITY
Address of Applicant :135 EAST COAST ROAD,
KANATHUR - 603 112 Tamil Nadu India
1)DR. A.S. PERUMAL
2)DR. N. MANOHARAN
3)MRS. VIJAYALAKSHMI C.H
(57) Abstract :
This invention discloses a method of generating power onboard ships using Tunnel Thrusters / Turbines. Tunnel thrusters / propellers
are fitted in the ship to generate power. They are permanent fittings inside the ship and located just below the draft level and inside the
double bottom tanks.

(19) INDIA
(54) Title of the invention : SELF REGULATING SLOW SPEED TURBO CHARGER SYSTEM IN DIRECTLY COUPLED
MARINE PROPULSION ENGINES
(51) International classification :B63H
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AMET UNIVERSITY
112 Tamil Nadu India
1)Prof. D.Immanuel Thiagarajan
2)Dr. N. Manoharan
3)Prof. T.Mohan
4)Prof. A.Venugopal
(57) Abstract :
Self Regulating Slow Speed Turbo charger system in directly coupled Marine Propulsion Engines The present invention is directed to
a system of Turbo Charger in a Marine Propulsion Engine that will have self regulation on the production of exhaust gas at slow speed
operation and maintain optimum operation of the Turbo charger in a Marine Propulsion Engine.

(19) INDIA
(54) Title of the invention : SYSTEM AND METHOD FOR DYNAMIC JOB ALLOCATION BASED ON ACOUSTIC
SENTIMENTS
(51) International classification :H04M
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)WIPRO LIMITED
1)Nithya Ramkumar
2)Soham Bhaumik
3)Amit Krishna
4)Mahesh Chowdary
5)Hemant Kumar
(57) Abstract :
The present disclosure relates to methods of systems for allocating a call from a user to an agent. Embodiments of the disclosure may
determine a set of sentiment indicators associated with the user from one or more acoustic parameters of the call. In addition,
embodiments of the disclosure may select a candidate agent to handle the call based on the set of sentiment indicators and a sentiment
handling capability associated with the candidate agent. Moreover, embodiments of the disclosure may allocate the call to the
candidate agent.

(19) INDIA
(54) Title of the invention : SYSTEM AND METHOD FOR STRENGTHENING SOFTWARE ARCHITECTURE USING A
COMPREHENSIVE CORE PRACTICE
(51) International classification :G01S
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Dr. CHITTA VENKATA PHANI KRISHNA
Address of Applicant :8-241, Gayatri Nilayam, Srinivasa
Nagar, Tadigadapa(Post), Penamaluru(Mandal), Vijayawada,
Krishna(Dt), Andhra Pradesh-521137, India. Andhra Pradesh
India
1)Dr. CHITTA VENKATA PHANI KRISHNA
2)Dr. KURRA RAJASEKHARA RAO
(57) Abstract :
Exemplary embodiments of the present disclosure are directed towards a system and method for strengthening the software
architecture by using a comprehensive core practice defining at computing device comprising at least one metaphor unit for
strengthening at least one software architecture. Maintaining consistency of a program code for the software architecture by the
developer across a metaphor unit. Breaking the program code signs into smaller modules for addressing the software architecture
components and functionality. Examining the program code signs results from the metaphor unit to see whether program code signs
exist for the major components and functionality of the software architecture. Checking the software architecture components and
functionalities for identifying interactions are left indescribable by the metaphor unit. Checking the metaphor unit whether the
software architecture making complicated. Obtaining the flexible software architecture by avoiding the interactions and complicated
architecture by architecture lite.

(19) INDIA
(54) Title of the invention : GREEN CORROSION INHIBITOR FOR STEEL IN ACID MEDIUM
(51) International classification :C23F11/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR. REXIN THUSNAVIS. G.
Address of Applicant :DEPARTMENT OF CHEMISTRY,
PIONEER KUMARASWAMY COLLEGE, NAGERCOIL Tamil
Nadu India
2)DR. VINOD KUMAR. K. P
1)DR. REXIN THUSNAVIS. G.
2)DR. VINOD KUMAR. K. P
(57) Abstract :
Phoenix dactyliferasQQd is subjected to corrosion evaluation by the following methods Weight loss - reveals nearly centum
percentage inhibition efficiency at 30°C. - even at 50°C, the metal is protected appreciably. Free energy and enthalpy values
correspond to spontaneous adsorption of the inhibitor and protection of the metal. The electrochemical investigations indicate the
mixed mode of inhibition and the mechanism of inhibition is through adsorption. The adsorption is due to the lone pair of electrons
present in the hetero atoms of the P. dactyliferawhich is validated from IR spectral studies. The SEM photographs bring to light the
protective nature of steel by inhibitor. The results suggest that the seed of/, dactylifera is an effective corrosion inhibitor, which can
be substituted for synthetic inhibitor for better performance and environmental protection.

(19) INDIA
(54) Title of the invention : SPAASH BRICKS
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR. S. LAVANYA PRABHA
Address of Applicant :AE53, 1ST STREET, SHANTHI
COLONY, ANNA NAGAR, CHENNAI - 600 040 Tamil Nadu
India
2)MRS. R. SWETHA
3)MR. R. SATHISH
1)DR. S. LAVANYA PRABHA
2)MRS. R. SWETHA
3)MR. R. SATHISH
(57) Abstract :
The SPAASH Bricks are made by appropriate recycling of these industrial by product materials like fly ahs , copper slag, Gypsum and
phosphor gypsumis. The SPAASH Brick is made to evaluate the technical possibilities of incorporating fly ash, copper slag and
gypsum in production of building blocks. Various mixtures were prepared by incorporating these industrial wastes with different
weight proportion. The suitable mix proportion was founded as 1:2:2 ([G+PG+C]: CS: FA) after several attempts. With these
proportions the building blocks are cast. The physical and mechanical properties like unit weight, compressive strength, flexural
strength, tensile strength, dimensional stability, water absorption and efflorescence values of that specimen were founded out. The
results were compared with conventional building blocks and fly ash bricks, results shows a very good increase in the values. Thus,
the utilization of these wastes additives is not only for conservation of clay resources, but also an alternative solution to difficult and
expensive waste disposal problems copper slag and fertilizer units waste.

(19) INDIA
(54) Title of the invention : STATION BORING MACHINE FOR UNDERGROUND TRANSIT RAIL STATION
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)NARESH KUMAR. M
Address of Applicant :NO. 16/9, FRANCIS TURIN STREET,
SEVENWELLS, CHENNAI - 600 001 Tamil Nadu India
1)NARESH KUMAR. M
(57) Abstract :
This invention relates to earth excavation machines and moreover particular to tunnel boring machines for underground station box
construction. The primary object of present invention is to provide tunnel boring machine for station box generally rectangular cross-
section configuration .This station boring machine is classified into Hard rock SBM and Earth pressure SBM consists of upper level
cutter head for concourse level and lower level cutter head for platform level. Where the SBM advances to earth face by self crawling
system and extension-contraction of thrust cylinders over the precast segments interconnected by ring rods suitably shaped to form
rectangular cross-section station box.

(19) INDIA
(54) Title of the invention : UNDERGROUND LEVEL GRAVITY WATER PUMP
(51) International classification :B01D
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)Chenniyappa Raju
Address of Applicant :No: 113, 3rd Main Road,
A.G.S.Colony, Anandhnagar, H.A.Farm Post, Bangalore-560 024,
Karnataka, India Karnataka India
1)Chenniyappa Raju
(57) Abstract :
Underground Level Water Gravity Pump that lifts water from underground level solely making use of gravitational force, without
using electrical energy. The device, a conduit frame has two vertical and horizontal conduits running parallel to each other. The two
vertical columns accommodate a piston (4, 4a) with connecting rod (5, 5a) linking a non-return valve (8, 8a) placed above it, arresting
the reverse flow of water. The upper and lower horizontal conduit of the frame (2, 2a) accommodates water/oil/ (1) and is sealed. An
inlet tube (7), through which the water enters is positioned at the bottom half of the device, equipped with a non-return valve (6, 6a)
on both the sides and an outlet tube (11, 11a) through which water exits is positioned at the top half of the device with a reserve outlet
pipe (20, 20a) with outlet air vent (21, 21a) and end cap (19, 19a).

(19) INDIA
(54) Title of the invention : BANANA SHAPED FOOT CLEANING DEVICE
(51) International classification :E04G
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)GEORGE P JACOB
Address of Applicant :S/O MATHAI CHACKO, AGED 38
YEARS, PALATH HOUSE, KANDAMANGALAM (PO),
MANNARKAD VIA, MANNARKAD TALUK, PIN - 678 583,
PALAKKAD DISTRICT Kerala India
1)GEORGE P JACOB
(57) Abstract :
A portable foot scrubbing device made with HIPS plastic and cement mortar with a total length of 9.5 inches, width 9.5 inches and
with height of 3.5 inches consist banana shaped foot scrubbing unit and palette shaped base with linch height. The said bottom of the
base is pasted with 5 mm thick rubber foam which works as a grip while in use. On the lower part of the top of the said palette base, 1
inch height and 3mm thick curved banana shaped wall is moulded, in the inner center of the said wall four anchor hooks in a sequence
are also moulded. The said wall strengthens and provides the shape of the curved banana to the cement mortar. On the center of the
top end portion of the said wall a rectangular shaped projection is made with 1.5 inch length, 1 inch height and with 10mm thickness,
the same termed as toe holder a slight curving is also made on the front top of the device. The toe holder is for the purpose of holding
the device by toe and the adjacent finger while scrubbing on the device with other foot. The banana shaped concrete is coated with tile
polish to reduce the roughness and to increase the life of the banana shaped mortar. A hole with 15 mm diameter is made in the front
top end portion of palette shaped base, that helps in easy hanging of the device on the wall while not in use. The banana shaped
concrete is coated with tile polish to reduce the roughness and to increase the life of the banana shaped mortar. Now the device is
ready for complete foot cleaning in all angles by rubbing. The unique design of curved banana shaped wall along with cement mortar
is a break through in the field of foot rubbing as it ensures comprehensive foot cleaning.

(19) INDIA
(54) Title of the invention : A NOVEL PROCESS FOR THE PREPARATION OF MIRABEGRON
(51) International classification :C07C
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)VIVIMED LABS LTD,
Address of Applicant :H.NO. 4-7-102/6 & 11, VEERNAG
TOWERS, HABSIGUDA, HYDERABAD - 500 007, Telangana
India
1)DR.M.SAMBHU PRASAD SARMA, MALLELA
2)DR.GANGADHARA RAO, YARRAPOTHU
3)RAVEENDRA, PALAKALURI
4)SYAMA SUNDAR, DURGUMAHANTHI
5)RAVINDER REDDY, KALVALA
6)SRIDHAR REDDY, SHAKAMPALLY
(57) Abstract :
The present invention relates to a process for the preparation of Mirabegron compound of Formula-1, which involves an in-situ step,
for the reduction of (7)-2-hydroxy-7V-(4-nitrophenethyl)-2-phenylacetamide of formula-4 to obtained (7)-2-(4-nitrophenethylamino)-
l-phenylethanol of formula-5 without isolating the compound of formula-5 is converted to (7)-2-(4-aminophenethylamino)-l-
phenylethanol of formula-6 or its salts formula-6a, is treated with 2-(2-aminothiazol-4-yl) acetic acid of formula-7 or its acid
derivatives of fcrmula-7a to obtain Mirabegron compound of formula-I

(19) INDIA
(54) Title of the invention : AUTISM AND DISABILITY NORMALIZING METHOD FOR HUMAN CONDITIONS
(51) International classification :A61K38/00
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)DR.S.MOHANDAS
Address of Applicant :THOPPIL HOUSE, PARAKKARA
PO, THATTAYIL, PATHANAMTHITTA DIST., PIN. 691 525,
Kerala India
1)MR.THATTAYIL MOHANDAS
(57) Abstract :
The present invention disclosed the purpose of normalizing human disabilities by birth and naturally happening later by living style or
toxins. All the human disability is considered as conditions and have no medical treatment available

(19) INDIA
(54) Title of the invention : NON-DESTRUCTIVE EVALUATION OF MARINE COMPOSITES AND NANOCOMPOSITES
USING PHOTOTHERMAL DEFLECTION TECHNIQUE
(51) International classification :C07C
Filing Date
:NA
:NA
Filing Date
:NA
:NA
Filing Date
:NA
:NA
1)AMET UNIVERSITY
112 Tamil Nadu India
1)Dr. Anita R Warrier
2)Dr.N.Manoharan
(57) Abstract :
This invention discloses the use of photothermal deflection technique for non-destructive evaluation of defects and damages such as
cracks, corrosion in ship hulls and marine structures. Further since this technique is an optical one, it is the most suitable form of NDT
technique to evaluate Marine composites and nanocomposite structures.

Published patent and design registration information october 30th, 2015

Published patent and design registration information october 30th, 2015

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Was ist angesagt?

Was ist angesagt? (20)

Andere mochten auch

Andere mochten auch (20)

Ähnlich wie Published patent and design registration information october 30th, 2015

Ähnlich wie Published patent and design registration information october 30th, 2015 (10)

Mehr von InvnTree IP Services Pvt. Ltd.

Mehr von InvnTree IP Services Pvt. Ltd. (17)

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

Published patent and design registration information october 30th, 2015