3. That’s Why We Bring You
PerformaEdge
A line of performance-inspired Edge Systems from IMETCO
ES-1 Certification
Edge Systems from IMETCO have
successfully passed the three tests
required by the ANSI/SPRI ES-1
standard:
1. RE-1: Roof Edge Termination Test
The RE-1 test evaluates the perimeter attachment to a
minimum holding power of 100 pounds per foot. The
membrane is pulled at a 45-degree angle to the roof
deck to simulate a billowing. Failure occurs when the
membrane detaches from the edge termination, or the
termination detaches from its mounting.
2. RE-2: Pull-off Test for Metal Edge
Flashing
RE-2 evaluates the strength of the metal edge flashing
to ensure that the fascia system meets or exceeds
the building’s calculated design wind pressure.
An incremental load is applied to the face of the
specimen and held for 60 seconds, then removed and
increased in increments of 25 psf until 150 psf, then
increments of 10 psf are applied thereafter. The results
must meet or exceed the calculated design pressure
of the building. Failure occurs with securement loss of
any component of the roof edge, or deformation that
would hinder weather protection at the edge.
3. RE-3: Pull-off Test for Metal Wall
Coping
RE-3 evaluates the strength of a metal coping cap
to ensure that it meets or exceeds the building’s
calculated design wind pressure. Incremental loads
are applied as with the RE-2 test, where the load is
applied to the face and top simultaneously. Failure
occurs with the securement loss of any component
of the roof edge system, or deformation that would
hinder weather protection at the edge.
–3–
(800) 646-3826
e Metals Company, Inc.
5. ES-F™ Series Fascia ES-F Fascia
The old-school gravel stop and fascia of the past FASCIA COVER x 10'-0"
is no longer acceptable for most roof systems FASCIA CANT x 10'-0"
of today. Fascia systems must be tested and 6" CONCEALED SPLICE PLATE @ EACH JOINT
approved to meet the ANSI/SPRI ES-1 standard MEMBRANE FLASHING (by OTHERS)
as required by the IBC. 1/2" 1 1/4" ROOFING NAIL @ 12" o.c. MAX.
(by OTHERS)
Once again, with its line of fully tested Edge 1 1/2"
Systems, IMETCO demonstrates its commitment
to our customers by providing a full line of
performance-inspired fascia and coping for use
SPECIFY
with built-up, single ply, and modified roofing
systems.
Features and Benefits: 1 3/4"
• ANSI/SPRI ES-1 approved
• Tested face dimensions up to 9½ inches 1/2"
1 1/4" ROOFING NAIL @ 12" o.c. MAX.
• Two-piece design (by OTHERS)
• 10-foot standard lengths (other lengths available)
• 22-gauge galvanized steel cant dams
• Concealed 6-inch splice plate
• Factory fabricated corners and accessories
• Does not penetrate the roof membrane
• No exposed fasteners
• Installs securely with various membrane thicknesses Product: Face Size:
• 20-Year Blow-Off/Leak-Tight Warranty available
ES-F500 5.0 inches
• 20-Year Finish Warranty available
ES-F650 6.5 inches
Materials and Coatings ES-F800 8.0 inches
• .040, .050 & .063 aluminum
• 24- and 22-gauge galvanized steel ES-F950 9.5 inches
• 24- and 22-gauge stainless steel
• Pre-finished Kynar® coated aluminum & steel standard
• Post-coated Kynar® custom colors available
–5–
(800) 646-3826
e Metals Company, Inc.
7. EZ Edge™ EZ Edge Sloped and Peaked Coping
Formed Line 5/8" 5/8" 5/8"
7/8" 7/8"
IMETCO’s EZ Edge line combines
"B"
quality with economy. These products (4" STD.)
"C" "B" "C"
(4" STD.) (4" STD.) (4" STD.)
offer proven reliability and pleasing
aesthetics at a lower cost than
performance-inspired edge systems. "A"
For use with built-up, single-ply and (ACTUAL WALL WIDTH)
"A"
modified roofing systems, all of the EZ (ACTUAL WALL WIDTH)
Edge products are available with a 20-
year Kynar® finish warranty. EZ-Edge
fascia and coping is available with a
weather-tight warranty up to 10 years. EZ Edge Formed Fascias and Extender
4" 4"
Features and Benefits: SPECIFY (SPECIFY)
• Factory fabricated and field proven 1 1/2"
• Standard & project-specific profiles EQUAL
& sizes (SPECIFY)
• Simple, strong design (SPECIFY)
(SPECIFY)
• 10-foot standard lengths
(other lengths available) EQUAL
1 1/2"
• Concealed 6-inch splice plates
• Factory-made corners, end caps, etc.
• Mitered and fully welded corners, 1 1/2"
end caps, transitions, etc. available
• Welded radius coping, fascia & gutter
• 20-Year Finish Warranty available EZ Edge “A” and “D” Style Gutter, and Downspout
Materials and Coatings 1" 1" 1" 1"
• .032, .040, .050, .063, .080 & .125 1" 1"
aluminum
(SPECIFY)
• 24- and 22-gauge galvanized steel (SPECIFY) (SPECIFY)
• 24-gauge stainless steel 2"
• Pre-finished Kynar® coated 1"
aluminum and steel standard (SPECIFY) (SPECIFY)
(SPECIFY)
• Post-painted Kynar® custom colors
available
–7–
(800) 646-3826
e Metals Company, Inc.
8. IMETCO’s 28 standard, designer and premium colors are all “cool” colors, with
SR measurements of .25 or better. Custom colors and specialty finishes are also The Total Solution
available. Ask your IMETCO representative for more information. IMETCO offers a full line of metal roofing,
wall, and edge systems and accessories.
Be sure to ask your representative for
Standard Collection information about other products and
solutions from IMETCO, such as:
Irish Mist Almond Suede Emerald Forest Blue Sapphire
Series 300® Standing Seam
Metal Roofing System
Tuscan Slate Epic Bronze Solar White Cadet Gray
• Precision engineering for long-term
weather-tight performance
Sandstone Chestnut Georgian Brick Opal Star • Rigorously tested to be leakproof and
to withstand hurricane-force winds
Colonial Red Silver Cloud Wedgewood Weathered Copper • Ideal for structural or architectural
applications
• One-piece clip facilitates unlimited
thermal movement
Designer Collection • 2⅜-inch high symmetrical seam with
a separate, easy-to-install seam cap
Iron Mountain Cardinal Red Carolina Coast • Factory-applied hot-melt sealant that
remains isolated from the clip
• Can be curved or tapered
Natural Patina Caribbean Coral Merlot
Total Metal Roof & Deck System
Premium Collection • IMETCO Series 300 ® standing seam
metal roofing
• Martin Fireproofing Perform-A-Deck
Platinum Silver Roman Copper metal roof deck system
• Tested to resist extreme winds and
Brite Copper Champagne impact from wind-born debris, as
recommended by FEMA 361: Design
and Construction Guidance for
Preweathered Galvalume Galaxy Blue Community Safe Rooms
• Single source warranty covers
complete assembly
Signature Collection* Prestige Collection* AquaBlock™ Underlayment
• Heat tolerant (250+°f)
• Engineered for metal and tile roofing
• Self-adhering, self-sealing
• 100% SBS-modified
Antiqu Bronze Acrylic Galvalume • 90-day exposure resistance
United Zinc:
Glacier Gray
United Zinc:
Onyx Black
The IMETCO Advantage
For more than a decade, we at IMETCO
have enjoyed our reputation as a
Artisan Steel Copper Patina manufacturer committed to providing
products of only the highest quality.
Our staff comprises expertise in metal
roofing, design, engineering, testing, code
compliance, manufacturing, and more.
Above all, our staff excels in providing
unparalleled customer service.
Field Stone TextureMatte Copper
At IMETCO, your
Quartz Stainless Steel satisfaction is our only
measure of success!
The colors above are for reference only. To select your final color, please request a metal color sample.
* Signature and Prestige Collections are available for select products. Special conditions may apply. Contact your IMETCO representative for more information.
Galvalume® is steel pre-treatment and a registered trademark of Biec International Inc. Hylar® is a fluorocarbon paint finish available on our metal products, and is a registered trademark of
Ausimont USA Inc. Kynar® is a fluorocarbon paint finish available on our metal products, and is a registered trademark of Elf Atochem North America Inc.
FM® (Factory Mutual) is a world leader in property loss prevention and control engineering, research, and training. Its research-based recommendations set new standards that reduce the
chance of property loss due to fire, weather conditions, and failure of electrical or mechanical equipment. It is a registered trademark of Factory Mutual Global, and must be identified as such
4648 S. Old Peachtree Rd • Norcross, GA 30071
whenever referred to in print. 800.646.3826 (p) s 770.908.2264 (f)
Series 300® and all other trademarks are owned by Innovative Metals Company, Inc. (IMETCO).
www.imetco.com