ICR SPRINT SC9 CREAMY YELLOW PUTTY - Stucco per lamiere zincate ed alluminio ...
ICR SPRINT-AIR PRIMER - Fondo acrilico 2K HS ultra rapido / 2K HS acrylic primer ultra fast
1. Fondo acrilico a due componenti alto solido
a basso contenuto di solvente
con eccezionale rapidità di essiccazione.
Adatto per tutte le riparazioni
(ritocco e verniciature complete).
Di elevato spessore, non assorbe
e consente finiture uniformi e brillanti.
È di facile carteggiatura e sovraverniciabile
con qualsiasi tip di smalto.
Il valore limite di VOC, in accordo alla normativa
2004/42, per questo prodotto appartenente alla
sottocategoria IIB(c) è 540 g/l.
Il VOC di questo prodotto pronto uso
è inferiore ai 540 g/l.
2K HS (High Solid) Acrylic primer at low content
of solvent, with exceptional fast drying times.
Ideal for all kinds of repairs (spot or whole car repair).
It allows application on several layers, it is not absorbing
and gives the finish an even and high gloss.
It can be easily sanded and it can be overpainted with
any kind of finish.
The EU VOC limit, in compliance with the 2004/42/CE
directive, for this product belonging to the subcategory
IIB(c), is 540 g/l.
The EU VOC limit for this ready-to-use product is 540 g/l.
SPRINT-AIR PRIMER.
2K HS ACRYLIC PRIMER
ULTRA FAST.
SPRINT-AIR PRIMER.
FONDO ACRILICO 2K HS
ULTRA RAPIDO.
www.icrsprint.com
EXPRESS AIR SYSTEM
2. IT SCHEDA TECNICA F76/ 77/ 78/ 79
SPRINT-AIR PRIMER
Fondo acrilico 2K HS ultra rapido
SPRINT-AIR PRIMER
2K HS acrylic primer ultra fast
A) DESCRIPTION AND FIELDS OF APPLICATION:
High solid two component product at low content of solvent,
very suitable for new jobs and repairs. It hardens very rapidly, sands
very easily, non absorbing. It gives the finish an even and high gloss.
It can be overpainted with any type of finish.
The EU limit for this product (subcategory IIB(c) )is 540 g/l.
The VOC of this product is below 540 g/l.
B) TECHNICAL DATA:
Composition: Hydroxylated resins, pigments, mineral charges
and solvents
Specific weight: 1,572 ± 0,05 Kg/Lt
Available colours: Grey
Safety data: See safety data sheet
C) SURFACE PREPARATION:
• Bare metal, zinc-plated sheets, polyester laminates, wood,
polyester fillers, etc.
• Old finishes, including the double-coat ones.
• Sand with P180-P220.
• Clean the surface to be treated with V09 Antisil. Make sure it
is dry and free from silicone, wax, grease and any
extraneous material.
D) CAUTIONS:
> Allow flash-off time between coats, depending on reduction and
temperature.
> If used as a sealer, reduce at 20% with thinner for acrylics.
> Do not utilize the product at temperatures below 5°C.
> Store in a cool and dry place.
E) PROCESSING:
5:1 (12% by weight) hardener C15-C16 Pot life > 45’ at 20°C
5-10% with D10-D11 thinners
52”- 20” DIN 4 mm at 20°C
1,5-1,8 mm 2-4 bar
2-3 = 100-200 microns
10’ at 20°C
50’ at 20°C
5’-10’ at 60°C
5’ at 1 m
P320-P400
P600-P1000
F) TOOLS CLEANING:
> With nitro thinner.
G) RECOATING:
2K enamel top coats
double coat solvent-soluble enamels
double coat water-soluble enamels
Technical indications and advices are based on our own experiences.
We assure the perfect quality of products. However, being the utilization out of our
control, we assume no responsibility on the results obtained.
EN TECHNICAL SHEET F76/ 77/ 78/ 79
A) DESCRIZIONE E CAMPO D’IMPIEGO:
Fondo acrilico a due componenti alto solido e basso contenuto di solvente
adatto per lavori nuovi e di riparazione. E’ di rapidissimo indurimento e
facile da carteggiare. Non assorbe e conferisce alle vernici di finitura
una brillantezza uniforme ed elevata. Sovraverniciabile con qualsiasi tipo
di vernice. Il valor limite di VOC, in accordo alla Normativa 2004/42,
per questo prodotto appartenente alla sottocategoria IIB(c) è 540 g/l.
Il VOC di questo prodotto pronto uso è inferiore ai 540 g/l.
B) NOTE TECNICHE:
Composizione: Resine acriliche ossidrilate, pigmenti,
cariche minerali e solventi
Peso specifico: 1,572 ± 0,05 Kg/Lt
Colori disponibili: Grigio
Dati di sicurezza: Fare riferimento alla scheda di sicurezza
C) PREPARAZIONE DEL SUPPORTO:
• Lamiera nuda, lamiera zincata, laminati in poliesteri, legno,
stucchi poliestere, ecc.
• Vecchie finiture comprese quelle in acrilico termoplastico e
doppio strato.
• Carteggiare con carta abrasiva P180-P220.
• Pulire bene la superficie da trattare con Antisil V09 e
assicurarsi che sia asciutta e priva di silicone, cere, grassi
e sostanze estranee in genere.
D) AVVERTENZE:
> Rispettare i tempi di appassimento tra una mano e l’altra a seconda
della diluizione e della temperatura.
> Per utilizzare il prodotto come isolante diluire al 20% con diluente
per fondi acrilici.
> Non utilizzare il prodotto a temperature inferiori a 5°C.
> Conservare in luogo fresco ed asciutto.
E) LAVORAZIONE CON CARTEGGIATURA:
5:1 (12% in peso) catalizzatore C15-C16 potlife > 45’ a 20°C
5-10% con diluente D10-D11
52”-20” DIN 4 mm a 20°C
1,5-1,8 mm 2-4 bar
2-3 = 100-200 micron
10’ a 20°C
50’ a 20°C
5’-10’ a 60°C
5’ a 1 mt
P320-P400
P600-P1000
F) PULIZIA DEGLI ATTREZZI:
> Con diluente nitro o da lavaggio.
G) PROSECUZIONE DELLA LAVORAZIONE:
Smalti di finitura bicomponenti
Smalti doppio strato a solvente
Smalti doppio strato ad acqua
Le informazioni tecniche ed i suggerimenti sono conformi a quanto risulta dalle nostre esperienze.
Noi assicuriamo la perfetta qualità del prodotto. Tuttavia, non essendo le condizioni di
utilizzo sotto il nostro controllo, non assumiamo nessuna responsabilità sui risultati ottenuti.
I.C.R. S.p.A. ITALIA - Reggio Emilia Tel. + 39/0522.517803 – Fax + 39/0522.514384 E-mail: info@icrsprint.it – www.icrsprint.com |
ICR SPRINT COATING UK LTD UK - London - T: 01278802011 E-mail: enquiries@icrsprint.co.uk www.icrsprint.com |
ICR SPRINT INC USA - Fall River - MA - T: 800 980 4071 E-mail: icrsprintusa@gmail.com www.icrsprint.com |
ICR Ibérica, S.A. SPAIN - Tel. +34/901 101 408 E-mail: info@icriberica.com www.icriberica.com