ABABOL Products have a range of solvent-free release agent for application in the roto-moulding industry. Our products do not create a build-up and have no contaminating transfer to the finished piece. The high performance of these products allows a large number of releases with significant savings in the manufacturing process. More info at: http://www.ababoldemould.com/en/rotomolding/

2. ABABOL cleaners Cd, C and C+ are formulated in preparation for cleaning, both new and used molds prior to treatment with sealers and / or mold releases. The sealers give the mold surface a transparent, flexible and strong film. This film is adhered to the substrate, sealing potential sticking
points. Ababol S eco (water based) or ABABOL TP (solvent based) allows an increase in the molds life, with safety margin against possible adhesions, making a more safe and effective mold release action. More technical info: www.ababoldemould.com
15-200ºC
350ºC
Fast curing at room
temperature.
12 month. Ensure the lid is
securely closed, at
temperatures below 25 ° C
For release on high
performance polymers,
provides the mold
surface a strong and durable
microstructure. High performance
mold releases. Free of volatile
organic compounds. Suitable for
the majority of polymers.
Manual Application (with clean
rags, cellulose paper) or spraying.
Ensure that all surfaces are
cleaned. High performance: 50-75
m2 / l Apply 3 layers of release
agent, waiting 15 min between
each coat.
At higher temperatures of 30 ° C,
waiting time can be reduced by 10
minutes and above 50 ° C less tan
5 minutes. NO ADDITIONAL
CURING TIME for the FINAL
LAYER is REQUIRED. During the
work process, only apply a new
coat when required.
15-200ºC
350ºC
Fast curing at room
temperature.
12 month. Ensure the lid is
securely closed, at
temperatures below 25 ° C
For release on high
performance polymers,
provides the mold
surface a strong and durable
microstructure. High performance
mold releases. Free of volatile
organic compounds. Suitable for
the majority of polymers.
Manual Application (with clean
rags, cellulose paper) or spraying.
Ensure that all surfaces are
cleaned. High performance: 50-75
m2 / l Apply 3 layers of release
agent, waiting 15 min between
each coat.
At higher temperatures of 30 ° C,
waiting time can be reduced by 10
minutes and above 50 ° C less tan
5 minutes. NO ADDITIONAL
CURING TIME for the FINAL
LAYER is REQUIRED. During the
work process, only apply a new
coat when required.
15-200ºC
350ºC
Fast curing at room
temperature.
12 month. Ensure the lid is
securely closed, at
temperatures below 25 ° C
For release on high
performance polymers,
provides the mold
surface a strong and durable
microstructure. High performance
mold releases. Free of volatile
organic compounds. Suitable for
the majority of polymers.
Manual Application (with clean
rags, cellulose paper) or spraying.
Ensure that all surfaces are
cleaned. High performance: 50-75
m2 / l Apply 3 layers of release
agent, waiting 15 min between
each coat.
At higher temperatures of 30 ° C,
waiting time can be reduced by 10
minutes and above 50 ° C less tan
5 minutes. NO ADDITIONAL
CURING TIME for the FINAL
LAYER is REQUIRED. During the
work process, only apply a new
coat when required.
15-60ºC
350ºC
Fast curing at room
temperature.
12 month. Ensure the lid is
securely closed, at
temperatures below 25 ° C
Release product based on high
performance polymers, provides
the mold surface a strong and
durable microstructure with very
high performance mold reléase and
lubricity.
Suitable for the majority of
polymers.
Application manual (with clean
rags, cellulose paper) or spraying.
Ensure that all surfaces are
cleaned. Always seal the surfaces
in all new
molds and in molds where it has
been deep cleaned. First apply 3
layers of release agent.
Allow each coat to dry 10 minutes,
drying time can be reduced to
5minutes above 50 ° C. During the
work process, only apply a new
coat when required.
15-60ºC
350ºC
Fast curing at room
temperature.
12 month. Ensure the lid is
securely closed, at
temperatures below 25 ° C
Release product based on high
performance polymers, provides
the mold surface a strong and
durable microstructure with very
high performance mold reléase and
lubricity.
Suitable for the majority of
polymers.
Application manual (with clean
rags, cellulose paper) or spraying.
Ensure that all surfaces are
cleaned. Always seal the surfaces
in all new
molds and in molds where it has
been deep cleaned. First apply 3
layers of release agent.
Allow each coat to dry 10 minutes,
drying time can be reduced to
5minutes above 50 ° C. During the
work process, only apply a new
coat when required.
15-60ºC
350ºC
Fast curing at room
temperature.
12 month. Ensure the lid is
securely closed, at
temperatures below 25 ° C
Release product based on high
performance polymers, provides
the mold surface a strong and
durable microstructure with very
high performance mold reléase and
lubricity.
Suitable for the majority of
polymers.
Application manual (with clean
rags, cellulose paper) or spraying.
Ensure that all surfaces are
cleaned. Always seal the surfaces
in all new
molds and in molds where it has
been deep cleaned. First apply 3
layers of release agent.
Allow each coat to dry 10 minutes,
drying time can be reduced to
5minutes above 50 ° C. During the
work process, only apply a new
coat when required.