it is the ppt of Operation of reciprocating pump under the subject of fluid power engineering or fluid mechanic

1. Operation of Reciprocating Pump
FLUID POWER ENGINEERING

2. introduction
• If mechanical energy is converted into
hydraulic energy by taking water inside the
cylinder in which piston is reciprocating, which
exerts thrust force on the liquid is known as
reciprocating pump.
• A reciprocating pump is a class of positive-
displacement pumps which includes the piston
pump, plunger pump and diaphragm pump.
• The given pump is single acting single cylinder
pump with air vessel. It can be used for less
discharge at higher heads. Priming is not
required because it is a positive displacement
pump. Reciprocating pumps are used in
pumping water in hilly areas


3. Components of reciprocating pumps
• Main parts of reciprocating pump
• A cylinder with a piston, piston rod
and cranka
• Suction pipe
• Delivery pipe
• Suction pipe
• Delivery pipe

4. Classification of reciprocating pump
• Based on contact of liquid
Single acting
Double acting
• Based on reciprocating member
Piston pump
Plunger pump
Bucket pump
• Based on number of cylinder
Single cylinder
Multi cylinder

5. • Discharge through a single acting reciprocating pump.
• D=diameter of the cylinder
• A=cross section area of the Piston or cylinder
• r=radius of the Crank
• N=RPM of Crank
• L=length of stroke = 2 x r
• hs=equals to suction head or height of excess of the cylinder from water surface in
sump
• hd=delivery head or height of the delivery outlet above the cylinder axis
• Discharge of water in one revolution = Area x Length of stroke
= A x L
• Number of revolution per second =N/60
• Discharge of pump per second
Q =Discharge in one second x number of revolution per second
= A x L x N/60 = ALN/60 m3/sec

6. Double acting reciprocating pump
• In case of double-acting pump, the water is
acting on both sides of the piston as shown in
figure. Thus, we require two suction pipes and
two delivery pipes for double-acting pump.
• When there is a Suction stroke on one side of the
piston, there is at the same time a delivery stroke on
the other side of the piston. Thus for one complete
revolution of the crank there are two delivery
strokes and water is delivered to the pipes by the
pump during these two delivery strokes.

7. Discharge through double acting reciprocating pump
• Discharge = water discharge + water discharge
• in forward stroke in reverse stroke
= ᴫD2L/4 + ᴫ(D2 – d2) L/4ᴫ
= ᴫD2L/4 + ᴫD2L/4 - ᴫd2L/4
= ᴫ (2D2 - d2) L/4 m3/cycle
= ᴫ (2D2 - d2) L/4 * N/60 m3/second
Q = 2ALN/60 ( NEGLECTING d2 )
Work done by double acting reciprocating pump
• Work done/second = weight of water delivered per second * head
lifted
= ρgQ * (hs + hd)
W.D./SECOND = 2ρgALN * (hs + hd) / 60

8. Slip of the reciprocating pump
• The difference of theoretical discharge and actual discharge is known
as slip of the pump, mathematically
  
















d
rh
act
d
th
act
th
actth
actth
C
Q
Q
C
Q
Q
Q
QQ
QQ
.......1001
1001100slipPercentage
Slip

9. Indicator Diagram
• The pressure variation in the cylinder
during a cycle consisting of one
revolution of the crank. When
represented in a diagram is termed as
indicator diagram.
• Figure represents an ideal diagram,
assuming no other effects are involved
except the suction and delivery
pressures.
• Point 1 represents the condition as the
piston has just started moving during
the suction stroke.

10. Indicator Diagram
• 1-2represents the suction stroke and the pressure in the cylinder is the
suction pressure below the atmospheric pressure.
• The point 3 represents the condition just as the piston has started
moving when the pressure increases to the delivery pressure. Along 3-
4 representing the delivery stroke the pressure remains constant.
• The area enclosed represents the work done during a crank revolution
to some scale
 
 
60
ds
ds
hhgLAN
p
hhgQp




