2. Anchor Lines for
Offshore Exploration
Product description
These ropes have robust constructions in order to be For rope sizes of 77mm (3 in) and less a 6x36/IWRC
able to withstand the deployment and redeployment pro- construction is recommended. For sizes greater than
cess when the drilling unit shifts location from one explo- 77mm up to 90mm (3_ in), a 6x41/IWRC rope is offered
ration job to the next. The ropes must be able to resist and for ropes with a diameter of 90mm to 103mm (4
crushing on the drum of multi-layered winches, bending in), 6x49/IWRC construction is available. For larger dia-
over fairleads, scraping along the sea bed, chaser dama- meter ropes the preferred construction is a 6x55/IWRC.
ge and corrosion to mention a few of the extraordinary These constructions change as the rope size increases to
rigours of anchoring. ensure that wires having appropriate properties for the
application are used.
Using one of the largest closing machines in the world,
Haggie can manufacture anchor lines as large as 150mm
in diameter in continuous lengths up to the equivalent of
120 tonnes per length.
Due to the rough handling anchor lines receive, its is
sometimes considered that a galvanised surface finish is
not warranted. This range of ropes is therefore available
as drawn-galvanised or ungalvanised.
Turret moored drillship
Vlasweg 2, 4782 PW Moerdijk, The Netherlands Phone: +31 (0) 168 35 85 65 Fax: +31 (0) 168 35 83 65
E-mail: info@europeanropeservices.nl Internet: www.europeanropeservices.nl
3. Anchor Lines for
Offshore Exploration
All anchor line ropes are manufactured in right regular
lay to limit rope torque in service. Ropes of 103mm (4
in) diameter and less are available in IPS, EIPS and
EEIPS grades. The larger ropes in the 6x55/IWRC
construction are supplied in EIPS grade as a standard.
Higher breaking forces are available subject to negotia-
tions at time of enquiry
One of the world's largest closing machines - an inte-
gral part of Haggie's offshore capability.
Vlasweg 2, 4782 PW Moerdijk, The Netherlands Phone: +31 (0) 168 35 85 65 Fax: +31 (0) 168 35 83 65
E-mail: info@europeanropeservices.nl Internet: www.europeanropeservices.nl
5. Drill Lines
Product description
The string of drill pipes is raised and lowered by means
of the drill line. This operation requires a rope construc-
tion with maximum resistance to abrasion and crushing
on the multi-layered drum.
The recommended rope is a 6x19/IWRC, EIPS grade,
right regular lay, ungalvanised.
The 9 large outer wires provide resistance to abrasion,
while the IWRC enhances crushing resistance as well as
contributes towards the rope breaking force. The right
regular lay reduces the tendency of the rope to build up
torque during the operation.
6x26C/IWRC UHP ropes have proved a major success in
rotary drilling applications.
An 8x19/IWRC rope construction has also been used
successfully for this application by some operators; the 8
strand construction provides superior fatigue life but the
smaller wires may adversely affect abrasion resistance.
Vlasweg 2, 4782 PW Moerdijk, The Netherlands Phone: +31 (0) 168 35 85 65 Fax: +31 (0) 168 35 83 65
E-mail: info@europeanropeservices.nl Internet: www.europeanropeservices.nl
6. Pennant Lines
Product description
These ropes are used for anchor recovery and are sub- All ropes are supplied in EIPS grade, right regular lay and
ject to very severe operating conditions. They are subjec- drawn-galvanised finish.
ted to continual vertical movement and consequent loca-
lised wear and fatigue in the part of rope nearest the Pennant lines can be supplied with mechanically spliced
anchor. In addition heavy loads are normally applied to eyes at both ends to enable connection to each other or
the rope during the recovery of anchors working over the the buoy or anchor.
stern roller of the work boat.
The rope details for the 6x25/IWRC construction are
The recommended ropes for this application are given in the table for Rod and Tubing lines and the
6x36/IWRC for rope diameters from 52mm to 77mm and details for the 6x36/IWRC construction are given in the
6x25/IWRC construction ropes for diameters below table for 6x37 class Anchor Line Ropes.
52mm.
Rod and Tubing/General Purpose Winch Lines
These ropes are used for anchor recovery and are sub- All ropes are supplied in EIPS grade, right regular lay and
ject to very severe operating conditions. They are subjec- drawn-galvanised finish.
ted to continual vertical movement and consequent loca-
lised wear and fatigue in the part of rope nearest the Pennant lines can be supplied with mechanically spliced
anchor. In addition heavy loads are normally applied to eyes at both ends to enable connection to each other or
the rope during the recovery of anchors working over the the buoy or anchor.
stern roller of the work boat.
The rope details for the 6x25/IWRC construction are
The recommended ropes for this application are given in the table for Rod and Tubing lines and the
6x36/IWRC for rope diameters from 52mm to 77mm and details for the 6x36/IWRC construction are given in the
6x25/IWRC construction ropes for diameters below table for 6x37 class Anchor Line Ropes.
52mm.
Vlasweg 2, 4782 PW Moerdijk, The Netherlands Phone: +31 (0) 168 35 85 65 Fax: +31 (0) 168 35 83 65
E-mail: info@europeanropeservices.nl Internet: www.europeanropeservices.nl