2. INTRODUCTION
Audio Spotlighting was invented by Dr. F. Joseph
Pompei developed by American technology
corporation.
Uses ultrasonic wave as carrier signal.
Audio spot lighting is a very recent technology that
creates a focussed beams of sound similar to light
beams coming out of a flash light.
Specific listeners can be targeted with sound without
others nearby hearing it.
It makes use of non-linearity property of air.
4. How is sound into a narrow beam?
Maintain a low beam angle that is dictated by
wavelength.
The smaller the wavelength,the less the beam angle,
the more focussed will be the sound.
The audio spot light uses ultrasonic energy to create
extremely narrow beams of sound .
5. How ultrasound wave works?
The ultrasound column acts as a airborne speaker,and
as the beam moves through the air gradual distortion
takes place in a predictable way.this gives rise to
audible components that can be accurately predicted
and controlled
6. WHAT IS AUDIO SPOTLIGHTING?
Simply audio spotlight looks like
a disk-shaped loud speaker
trailing a wire with a small laser
guide beam mounted in the
middle.
When one points the flat side of
the disk in your direction, you
here whatever sound one’s
chosen for you.
7. Range of hearing
Human ear - 20 Hz to20,000Hz.
No single loud speaker can operate
efficiently over such wide range of
frequencies.
By using this technology it is
possible to design a perfect
transducer which can work over a
wide range of frequency which is
audible to the human ear.
8. WORKING PRINCIPLE
The original low frequency sound wave such as human
speech or music is applied into an audio spotlight
emitter device.
This low frequency signal is frequency modulated with
ultrasonic frequencies range with wave length of few
millimeters.
Since the wavelength is smaller the beam angle will be
around 3 degree, as a result the sound beam will be a
narrow one with a small dispersion.
10. working
Due to the nonlinearity property of air new sounds
are formed within the wave.
The new frequencies (sounds) will be added into the
sound wave by the air itself.
The new sound signal generated will be
corresponding to the original information signal with
a frequency in the range of 20 Hz to 20 KHz .
Since we cannot here the ultrasonic sound, we only
hear the new sounds that are formed by the
nonlinear action of the air
12. Components of audio spotlighting
Power supply
Frequency oscillator
Modulator
Audio signal processor
Micro controller
Ultrasonic amplifier
transducer
13. 1. Power Supply: works off DC, ultra sonic amplifier
requires 48v for working and low voltage for other
components.
2. Frequency oscillator: generates ultra sonic
frequency signals (21,000 Hz to 28,000Hz).
3. Modulator : convert the source information into
ultrasonic signals. In addition, error correction is
needed to reduce distortion without loss of energy.
14. 4. Microcontroller: takes care of the functional management of
the system.
5. Audio signal processor: The audio signal is sent to an
electronic signal processor circuit where equalization, dynamic
range control, distortion control and precise modulation are
performed to produce a good quality sound signal.
6. Ultrasonic amplifier: High- efficiency ultrasonic power
amplifies the frequency modulated wave in order to match the
impedance of the integrated transducers. So that the output of
the emitter will be more powerful and can cover more distance.
15. 7. Transducer : It is1.27 cm thick and17”diameter.Produces
audibility up to 200 meters with better clarity of sound.
• Has the ability of real time sound reproduction with zero
lag.
• These transducers are arranged in form of an array called
parametric array in order to propagate the ultrasonic signals
from the emitter and thereby to exploit the nonlinearity
property of air.
17. Modes of listening
Direct Mode:
Requires a clear line of approach from the sound system unit to the poi
nt where the listener can hear the audio.
To restrict the audio in a specific area this method is appropriate.
Projected mode:
For this mode of operation the sound beam from an emitter
is made to reflect from a reflecting surface.
A virtual sound source creates an illusion of sound source
that emanates from a surface.
This method is appropriate when we want to send the
information to a large number of people.
18. ADVANTAGES
Small size
Single source
Ultimate control in audio placement
Minimizes noise pollution
Ease of installation
Lowest maintenance cost
Reduced feedback
19. DISADVANTAGES
Lack of mass production i.e, each unit must be handmade.
The most common form of distortion is clipping.
An LED on top of the Audio spotlight system reports
clipping, which is also perceptible to the listener as a kind
of a 'chirping' effect. If any signal produces distortion,
the input level of the source is reduced until perceptible
distortion is eliminated.
20. APPLICATIONS
SAFETY OFFICIALS: Portable audio spotlighting
devices for communicating with a specific person in
the crowd of people.
MUSEUMS: In museums audio spotlight can be used
to describe about a particular object to a person
standing in front of it, so that the other person
standing in front of the other object will not be able to
here the discription
MILITARY APPS :Ship to ship communication &
shipboard announcement.
21. Conclusion
Audio spotlighting system is going to shape the future
of sound and will serve our ears with magical
experience. So we can conclude- Audio Spotlighting
really “put sound where you want it” and will be
“A REAL BOON TO THE FUTURE.”
