Cutting is very important part in garments industry .Here i have enclosed some basic idea of cutting section . Cutting training Manual for Garments Industry .If we do not cut the fabric well as we will not produce good quality of products .Cutting PPT If you need any kind of assistance regarding technical compliance related .Please contract with me below address najmul0831@gmail.com

1. Fascilated by Md. Nazmul Huda ,BSc In textile CU,M.Sc in
Environmental science JU.
Training is a part of
learning lesson .

2. BABYLON GARMENTS LTD.
CUTTER MAN
TRAINING MENUAL

3. TRAINING PART :
Basic Training:
Advance :
On job:
(Floor)

4. TRAINING CONTENT:BASIC
Type of
Cutting
Machine.
Machine
Handling.
Machine Picture.
Straight Knife

5. TYPE OF MACHINE:BASIC
Band Knife
End
Cutter

6. Key points of a cutting machine: BASIC

7. Straight Knife Machine Parts: BASIC
Machine parts is above Short discussion is above
 MOTOR :
 It assures a Smooth Cutting Operation
with Excellent Cutting Power and Low Motor
Temperature.
AUTOMATIC OIL LUBRICATION DEVICE :
Oil can be supplied Automatically from Oil
Reservoir to the Guide Metals and Cross
Head. And the Internal oil Guard keeps other
Interior parts clean.
AUTOMATIC SHARPENING DEVICE:
There is an systematic Belt Sharpening
device. Just press down the Sharpening
lever, and the Blade can be sharpened
Automatically to maintain the most suitable
Edge of the Blade.
STANDARD :
Thinner and Flat type Standard makes the
Resistance of Cutting ,Material Lower, and
Bigger Blade Stoke makes Cutting Smoothly.
BASE PLATE :
The Base Plate is Low and Surface is
Smooth to make the Materials travel on it
Smoothly before and after Cutting.

8. Three Type of Cutting Machine
Manual
Semi Automatic
Automatic/Computerized.
Type of Cutting Machine: BASIC

9. Hand
Scissoring
Manual Machine: BASIC

10. Straight knife of Cutting Machine.
Round Knife Cutting Machine.
Band Knife Cutting Machine.
Die Cutting Machine.
Notched Machine.
Drill Machine.
Semi Automatic machine:BASIC

11.  Computer Controlled Knife Cutting Machine.
 Laser Cutting Machine.
 Water Jet Cutting Machine.
 Rib Cutting Machine.
 Air jet Cutting Machine.
 Ultrasonic Cutting Machine.
 Plasma Torch Cutting Machine.
Computerize Machine: BASIC

12.  A cutter man should know about marker &
marker ratio.
 Marker is the most important step before
cutting the fabric
 A marker is a diagram of a exact arrangement
of pattern pieces for sizes of a specific style
that are to be cut from in one spread
 Maker can be made manual or computerized
method.

13. Deferent type of Shape Cutting as per measurement is Bellow: On the floor training
 Length-12”
 Width-4”
 Length-12”
 Width-4”

14.  Buyer:
 Order
 Style:
 Token Collect from Supervisor:
 Approval Swatch:
 Fabric Inspection Report:
 Shade Group:
 Fabric weight as per Marker Management:
 Fabric Collection:
Spreading: Bellow information should be maintain
before spreading. Advance

15.  Ensure all safety & Compliance issues:
 Spreading is done as per approval:
 Marker is checked & confirmed the ration:
 Proper Clamping:
 Ratio is checked by supervisor:
 All necessary approval is taken from AQM to
proceed cutting:
 Small parts should be cut & out first.
Before Cutting a Cutter Man Should Consider: ADVANCE

16.  A cutter man should know well how to handle
the cutting machine.
 A cutter man must cut the panel according
the marker shape.
 Cutter man use PPE during the cutting.
 Cutter man also ensure the quality during the
cutting.

17. Fabric type No of Lay Lay Height Remarks
Linen 200 Lay 2.5 Inc.
T.C 300 Lay 3.00 Inc.
CVC 300 Lay 2.00 Inc.
Oxford Solid 250 Lay 3.00 Inc.
Oxford Stripe 250 Lay 3.00 Inc.
100% Cotton
Check
200 Lay 2.5 Inc.
Denim Hard 150 Lay 3.00 Inc.
Denim Soft 150 Lay 3.00 Inc.
Twill Cotton
Solid Hard
180 Lay 2.5 Inc.
Twill Cotton
Solid Soft
250 Lay 2.5 Inc.

18.  PP Meeting must be complete.
 Machine Check: Plain feed, proper run, oil etc.
 New knife not used for oxford fabric.
 Cutting as per proper shape maintain.
 Sleeve notch mark should not over pattern.
 Back ,Front ,Arm hole ,Shoulder point &
Bottom should be as per pattern shape.
QUALITY ISSUES:ADVANCE