1. HOLMATRO RESCUE TOOLS NASA/JPLFIRE DEPARTMENT BY: F.F. NICOLALDE

2. FIREFIGHTER SAFETY PPE’S Helmet, Gloves, Eye Protection F.F. Turnouts SCBA if necessary

3. SCENE SAFETY Ensure the scene is safe prior to exiting the apparatus (watch for traffic). Secure the scene prior to beginning extrication/ rescue operations. Place your vehicle on scene to protect the rescuers and victims from traffic. Ensure there aren’t any other safety issues that need to be secured first. i.e. -Down Power Lines Notify any additional resources. i.e. : ALS, Security / PD etc.

4. ENGINE-1 RESCUE TOOLS

5. HOLMATRO RESCUE TOOLS Spreaders3242-UL Max. Working Pressure: 10,500 PSI / 720 bar 19,595 lbs Max Spreading Force ¼ inch Max Spreading Distance 42.5 lbs Weight 33”x11 ½”x 8” Dimensions Oil volume required- opening 26 cu in closing 17.3 cu in

6. HOLMATRO SPREADERS 3242- UL A. Quick-action couplings C. Carrying handle D. Arm E. Spreading Tips B. Dead-man’s handle G. Proper storage spacing A. Quick-action couplings B. Dead-man’s handle C. Carrying Handle D. Arm E. Spreading Tips F. Safety relief valve G. Do not store under pressure Leave small gap between tips F. Safety relief valve

7. HOLMATRO RESCUE TOOLS Combi Tool3150-UL Max. Working Pressure: 10,500 PSI / 720 bar 67,600 lbs Max Cutting Force in Cutting Notch 28,300 lbs Max Cutting Force in Central Cutter 14 ¼ inch Max Spreading Distance 35 lbs Weight 33”x 9”x 7” Dimensions Oil volume required- opening 12.6 cu in closing 16.8 cu in

8. HOLMATRO COMBI TOOL3150- UL B. Carrying handle A. Dead-man’s handle E. Cutting Notches F. Proper storage spacing A. Dead-man’s handle B. Carrying Handle C. Arm D. Spreading Tips E. Cutting Notches F. Do not store under pressure Leave small gap between tips G. Quick action couplings –not shown H. Safety Relief Valve –not shown D. Spreading Tips C. Arm

9. HOLMATRO RESCUE TOOLS Cutters3020-UL Max. Working Pressure: 10,500 PSI / 720 bar 63,400 lbs Max Cutting Force 5¼ Max Blade Opening 27 ½ lbs Weight 33”x11 ½”x 8” Dimensions Oil volume required- opening 26 cu in closing 17.3 cu in

10. HOLMATRO CUTTERS 3020- UL A. Dead-man’s handle D. Cutting Blade E. Proper storage spacing C. Blade Arm A. Dead-man’s handle B. Carrying Handle C. Blade Arm D. Cutting Blade E. Do not store under pressure Leave small gap between tips F. Quick action couplings –not shown G. Safety Relief Valve –not shown B. Carrying handle

11. HOLMATRO RESCUE TOOLS Ram3321-UL Max. Working Pressure: 10,500 PSI / 720 bar 36,460 lbs Max Spreading Force 9 ¾” Max Opening 29 lbs Weight 21 ¼ ”x 15 ”x 4 ¾ ” Dimensions Oil volume required- opening 34.2 cu in closing 10 cu in

12. HOLMATRO RAM3321- UL B. Safety relief valve A. Quick-action couplings C. Dead-man’s handle E. Cylinder F. Proper storage spacing D. Cross Heads D. Cross Heads 39” 10” 20” G. Ram Extensions

13. HOLMATRO RAM EXTENSION B. Align Notch A. Female & Male Snap Lock C. Cross Head D. Ram Extensions

14. HYDRAULIC HOSES 100 FT LENGTH PRE-CONNECTED 33 FT LENGTH PROPER USAGE 1. Do Not Kink Hoses 2. Do Not pull the hoses to move the tools. 3. Prevent twisting of the hose 4. Do Not use hoses to keep equipment in position. (especially if hoses are pressurized)

16. Remove dirt and oil with a clean dry rag.

17. Clean with mild soap and water.

18. You may Lubricate the coupling with hydraulic oil or by spraying WD-40.

19. Spray behind the locking sleeve and the back end of the coupling. (Location A)Female coupling A Male Coupling Locking Sleeve Coupling dust caps NOTE: After removing dust caps from the hydraulic hoses, make sure to secure the dust caps on the power unit by fastening them together around the frame. This keeps the dust caps from getting dirty and getting lost.

20. HOLMATRO ACCESSORY PULLING CHAINS Pulling attachment tips with hooks Pulling chains: rated at chain strength grade 80, system 8, allowing a 2-1 safety working load with the rescue Holmatro tools. Material:Alloy steel, heat treated Pulling chains 4.5 FT 9 FT

21. HOLMATRO POWER UNIT2035 PHU E. Fuel Cap D. Choke switch C. Exhaust B. Hydraulic oil dipstick and Fill F. Air filter G. Fuel ON/OFF Switch A. Relief Valve with Connection Coupling H. Engine Switch ON/OFF (Back Side) I. Starting Cord J. Speed Switch K. Engine oil drain plug M. Hydraulic oil drain plug (underneath) L. Engine oil dipstick/filling nozzle (Back Side)

22. ENGINE-1 PORTABLE POWER UNIT OPERATIONS Ensure Proper PPE’s are worn during operation. Connect proper tool for rescue operations to the hydraulic hose found on the shelf above the hydraulic tools. Check fuel level, oil level, and hydraulic fluid levels, and ensure connections are secure. Ensure the Engine ON/OFF switch is in the On position. Ensure your fuel ON/OFF switch is in the On position. COLD START- ensure choke is in the On position and speed switch is on the fast position. Pull starting chord to start the engine. Once engine starts, turn off choke switch, and adjust engine speed. You are now ready to operate your Holmatro Tool. Turn the Operating Relief Valve to the Operation position. H. Engine Switch ON/OFF

23. HOLMATRO POWER UNIT2035 PHU (continued) L. Engine oil dipstick/filling nozzle A. Relief Valve with Connection Coupling HONDA 4 stroke engine 2.5 HP I. Starting Cord J. Speed Switch

24. ENGINE-1 FIXED POWER UNIT OPERATIONS Engine-1 Master Turn on Engine, and Power to the GEN/PTO inside the Engine Cab. Follow Steps A,B,C Turn on breaker main and corresponding breakers. Ensure Proper PPE’s are worn during operation. A. Turn Ignition switch to the ON position. B. Press Engine Start Toggle switch C. Turn On GEN. PTO Toggle switch

25. ENGINE-1 FIXED POWER UNIT OPERATIONS CIRCUIT BREAKER Circuit Breaker PTO PTO 2. Turn on breaker main and corresponding breakers.

26. HOLMATRO POWER UNIT2035 GU D. Pre-connected Hydraulic Hose A. ON- OFF B. Frame E. Hydraulic oil dipstick / fill F. Operating Relief Valve C. Connection Coupling 4. Check hydraulic fluid levels and ensure connections are secure. 5. Connect proper tool for rescue operations to the pre-connected hydraulic hose reel. 6. Turn the ON-OFF switch to the ON position depressing the GREEN button.

27. HOLMATRO POWER UNIT2035 GU B. Operating Relief Valve A. ON- OFF C. Connection Coupling 7. Turn the Operating Relief Valve to the Operation position. 8. You are now ready to operate your Holmatro Tool.

28. REMEMBER: SAFTEY FIRST END OF SLIDE SHOW