The Guide Right Surgical Guide System is a system of components for the fabrication and correction of diagnostic and surgical dental implant guides in 1 or 2 dimensions.

1. Serial Guide Technique
Featuring: #30
Fabrication of DIAGNOSTIC Guide using:
 5.3 Wide Guide Sleeve
 Serial Guide Sleeve Inserts
 Fabrication Insert (FABIN)
 Insert Removal Tool (IRT)
SURGICAL Guide in place
Serial Inserts Kits are available
DWYER 2.2013

2. Clinical view of proposed surgery site

3. Wax set up of #30 tooth

4. Hole drilled with 3/32” drill through wax up

5. 3/32” drill in cast indicates the planned prosthetic axis.

6. The drill is replaced with a 3 mm guide post.

7. Undercuts blocked out.

8. Lubricating cast with petroleum jelly prior to adding Triad® Gel

9. 5.3 Fabrication Insert (FABIN) used to center the 5.3 guide sleeve
on the guide post and to prevent Triad® Gel from entering sleeve.

10. Lingual view of FABIN in 5.3 mm guide sleeve with
guide sleeve cleats positioned toward the lingual surface.

11. Appropriate lubrication of lingual and occlusal
surfaces is required before applying Triad® Gel.

12. Cure each layer of Triad® Gel

13. 2nd layer of gel extended over several of the adjacent teeth

14. Buccal view
illustrating gel added to just cover occlusal & lingual surface of teeth.

15. Fabrication insert removed leaving 5.3 mm guide sleeve

16. Buccal view
5.3 mm wide guide sleeve

17. Axial view
5.3 guide sleeve is centered over the 3/32” hole

18. 2.25 mm insert is used for initial 2 mm drill

19. IRT (insert removal tool) used to remove insert from guide sleeve.

20.  SURGICAL guide with 5.3 guide sleeve is placed over IRT
 Set on a firm surface and tapped with downward pressure
to remove inserts.

21. 5.3 wide guide sleeve is used with appropriate inserts for drill sizes.
Shown here with 4 mm insert

22. SURGICAL guide in place
Appropriate inserts are used for each drill size
2.0 mm insert, for 1.8 mm drill ■ 2.7 mm insert for 2.5 mm drill …etc.
Completing the osteotomy with Astra 3.8 mm twist drill
plus 5.0 mm conical drill used in 5.3 mm sleeve without an insert.

23. Peri-apical X-ray of SURGICAL guide alignment.

24. Final X-ray

25. Guide Right™
Products shown in this case
 3/32” drill
 5.3 Wide Guide Sleeve
 Series of Inserts for 5.3 Guide Sleeve *next slide
 5.3 Fabrication Insert (FABIN)
 3 mm Guide Post
 Guide Sleeve Inserts for 5.3 Guide sleeve
 Insert Removal Tool (IRT)
 Petroleum Jelly
 Triad® Gel
 Recommended Kits: 4.5 / 5.3 Serial Guide Kit
1.800.314.0065 • www.deplaque.com

26. Serial INSERTS for 5.3 Guide Sleeves
Guide Right™
Individual Insert Sizes Available
2.25 mm
2.6 mm
2.75 mm
3.0 mm
3.6 mm
4.0 mm
4.2 mm
4.6 mm
Order directly from > www.deplaque.com

27. Serial INSERTS for 4.5 Guide Sleeves
Guide Right™
Fabrication Insert
INSERTS FOR 4.5 Guide Sleeve FABIN
Insert Removal Tool
Order directly from > www.deplaque.com

28. DéPlaque
Guide Right™ Surgical Guide System
fabricate ▪ evaluate ▪ correct ▪ verify ▪ place
Start With Precision. Place With Confidence.™
1.800.314.0065 • www.deplaque.com