3. Preface
Notice
The company reserves the right to revise this publication or to change its contents without notice. Infor-
mation contained herein is for reference only and does not constitute a commitment on the part of the man-
ufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or
inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage
resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, translated,
transmitted or reduced to any machine readable form without prior consent from the vendor, manufacturer
or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or registered
trademarks of their respective companies. They are mentioned for identification purposes only and are not
intended as an endorsement of that product or its manufacturer.
©June 2005
Trademarks
This product incorporates copyright protection technology that is protected by method claims of certain
U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights
owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and
is intended for home or other limited viewing uses only unless otherwise authorized by Macrovision Cor-
poration. Reverse engineering or disassembly is prohibited.
Intel®, Pentium® and Celeron® are US registered trademarks of Intel Corporation.
I

4. Preface
FCC Statement
(Federal Communications Commission)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
• Re orient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the service representative or an experienced radio/TV technician for help.
Warning
Use only shielded cables to connect I/O devices to this equipment. You are cautioned that changes or modifica-
tions not expressly approved by the manufacturer for compliance with the above standards could void your au-
thority to operate the equipment.
II

5. Preface
IMPORTANT SAFETY INSTRUCTIONS
Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and
injury to persons when using any electrical equipment:
1. Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub,
in a wet basement or near a swimming pool.
2. Avoid using this equipment with a telephone line (other than a cordless type) during an electrical storm.
There may be a remote risk of electrical shock from lightning.
3. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They
may explode. Check with local codes for possible special disposal instructions.
5. This product is intended to be supplied by a Listed Power Unit (DC Output 20V, 3.25A (65W) minimum
AC/DC Adapter, OR by a DC Output 20V, 4.5A (90W) minimum AC/DC Adapter if you are using the
optional port replicator- see pages 7 - 12 & C - 5).
CAUTION
Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equip-
ment.
TO REDUCE THE RISK OF FIRE, USE ONLY NO. 26 AWG OR LARGER,
TELECOMMUNICATION LINE CORD
This Computer’s Optical Device is a Laser Class I Product
III

6. Preface
Instructions for Care and Operation
The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions:
1. Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be dam-
aged.
Do not expose the computer Do not place it on an unstable Do not place anything heavy
to any shock or vibration. surface. on the computer.
2. Keep it dry, and don’t overheat it. Keep the computer and power supply away from any kind of heating
element. This is an electrical appliance. If water or any other liquid gets into it, the computer could be
badly damaged.
Do not expose it to excessive Do not leave it in a place Don’t use or store the com- Do not place the computer on
heat or direct sunlight. where foreign matter or mois- puter in a humid environment. any surface that will block the
ture may affect the system. Vents/Fan Intakes.
IV

7. Preface
3. Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other
strong magnetic fields. These can hinder proper performance and damage your data.
4. Follow the proper working procedures for the computer. Shut the computer down properly and don’t
forget to save your work. Remember to periodically save your data as data may be lost if the battery is
depleted.
Do not turn off the power Do not turn off any peripheral Do not disassemble the com- Perform routine maintenance
until you properly shut down devices when the computer is puter by yourself. on your computer.
all programs. on.
5. Take care when using peripheral devices.
Use only approved brands of Unplug the power cord before
peripherals. attaching peripheral devices.
V

8. Preface
Power Safety
The computer has specific power requirements:
• Only use a power adapter approved for use with this computer.
Power Safety • Your AC/DC adapter may be designed for international travel but it still requires a
Warning steady, uninterrupted power supply. If you are unsure of your local power specifi-
Before you undertake cations, consult your service representative or local power company.
any upgrade proce- • The power adapter may have either a 2-prong or a 3-prong grounded plug. The
dures, make sure that third prong is an important safety feature; do not defeat its purpose. If you do not
you have turned off the have access to a compatible outlet, have a qualified electrician install one.
power, and discon- • When you want to unplug the power cord, be sure to disconnect it by the plug head,
nected all peripherals
and cables (including
not by its wire.
telephone lines). It is • Make sure the socket and any extension cord(s) you use can support the total cur-
advisable to also re- rent load of all the connected devices.
move your battery in • Before cleaning the computer, make sure it is disconnected from any external
order to prevent acci- power supplies (i.e. AC/DC adapter or car adapter).
dentally turning the
machine on.
Do not plug in the power Do not use the power cord if Do not place heavy objects
cord if you are wet. it is broken. on the power cord.
VI

9. Preface
Battery Precautions
• Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the com-
puter.
• Do not remove any batteries from the computer while it is powered on.
• Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any
way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage,
which may possibly result in fire.
• Recharge the batteries using the notebook’s system. Incorrect recharging may make the battery explode.
• Do not try to repair a battery pack. Refer any battery pack repair or replacement to your service representative
or qualified service personnel.
• Keep children away from, and promptly dispose of a damaged battery. Always dispose of batteries carefully.
Batteries may explode or leak if exposed to fire, or improperly handled or discarded.
• Keep the battery away from metal appliances.
• Affix tape to the battery contacts before disposing of the battery.
• Do not touch the battery contacts with your hands or metal objects.
Battery Disposal & Caution
The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its
useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste
stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal.
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended
by the manufacturer. Discard used battery according to the manufacturer’s instructions.
VII

10. Preface
Cleaning
Do not apply cleaner directly to the computer; use a soft clean cloth.
Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer.
Servicing
Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and
the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer
from the power supply. Then refer servicing to qualified service personnel under any of the following con-
ditions:
• When the power cord or AC/DC adapter is damaged or frayed.
• If the computer has been exposed to rain or other liquids.
• If the computer does not work normally when you follow the operating instructions.
• If the computer has been dropped or damaged (do not touch the poisonous liquid if the LCD panel breaks).
• If there is an unusual odor, heat or smoke coming from your computer.
Removal Warning
When removing any cover(s) and screw(s) for the purposes of device upgrade, remember to replace the cover(s)
and screw(s) before turning the computer on.
VIII

11. Preface
Travel Considerations
Packing
As you get ready for your trip, run through this list to make sure the system is ready to go:
1. Check that the battery pack and any spares are fully charged.
2. Power off the computer and peripherals.
3. Close the display panel and make sure it’s latched.
4. Disconnect the AC/DC adapter and cables. Stow them in the carrying bag.
5. The AC/DC adapter uses voltages from 100 to 240 volts so you won’t need a second voltage adapter.
However, check with your travel agent to see if you need any socket adapters.
6. Put the notebook in its carrying bag and secure it with the bag’s straps.
7. If you’re taking any peripherals (e.g. a printer, mouse or digital camera), pack them and those devices’
adapters and/or cables.
8. Anticipate customs - Some jurisdictions may have import restrictions or require proof of ownership for
both hardware and software. Make sure your “papers” are handy.
Power Off Before Traveling
Make sure that your notebook is completely powered off before putting it into a travel bag (or any such container).
Putting a notebook which is powered on in a travel bag may cause the Vents/Fan Intakes to be blocked. To pre-
vent your computer from overheating make sure nothing blocks the Vent/Fan Intakes while the computer is in
use.
IX

12. Preface
On the Road
In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshoot-
ing, keep these points in mind:
Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is
very common. Don’t check it with “normal” luggage. Baggage handlers may not be sufficiently careful.
Avoid knocking the computer against hard objects.
Beware of Electromagnetic fields - Devices such as metal detectors & X-ray machines can damage the
computer, hard disk, floppy disks, and other media. They may also destroy any stored data - Pass your
computer and disks around the devices. Ask security officials to hand-inspect them (you may be asked to
turn it on). Note: Some airports also scan luggage with these devices.
Fly safely - Most airlines have regulations about the use of computers and other electronic devices in
flight. These restrictions are for your safety, follow them. If you stow the notebook in an overhead com-
partment, make sure it’s secure. Contents may shift and/or fall out when the compartment is opened.
Get power where you can - If an electrical outlet is available, use the AC/DC adapter and keep your bat-
tery(ies) charged.
Keep it dry - If you move quickly from a cold to a warm location, water vapor can condense inside the
computer. Wait a few minutes before turning it on so that any moisture can evaporate.
X

13. Preface
Developing Good Work Habits
Developing good work habits is important if you need to work in front of the computer for long periods
of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your
hands, wrists or other joints. The following are some tips to reduce the strain:
• Adjust the height of the chair and/or desk so that the keyboard is at or slightly
below the level of your elbow. Keep your forearms, wrists, and hands in a relaxed
position.
• Your knees should be slightly higher than your hips. Place your feet flat on the
floor or on a footrest if necessary.
• Use a chair with a back and adjust it to support your lower back comfortably.
• Sit straight so that your knees, hips and elbows form approximately 90-degree
angles when you are working.
• Take periodic breaks if you are using the computer for long periods of time.
Remember to:
• Alter your posture frequently.
• Stretch and exercise your body several times a day.
• Take periodic breaks when you work at the computer for long periods of time. Fre-
quent and short breaks are better than fewer and longer breaks.
XI

14. Preface
Lighting
Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your
neck and shoulders.
• Position the display to avoid glare or reflections from overhead lighting or outside sources of light.
• Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen
clearly.
• Position the display directly in front of you at a comfortable viewing distance.
• Adjust the display-viewing angle to find the best position.
XII

15. Preface
Contents
Notice ...........................................................................I Hot-Key Buttons & Keyboard ............................... 1-10
FCC Statement .......................................................II Function Keys ........................................................ 1-11
Instructions for Care and Operation ..................... IV System Map: Front & Rear Views ......................... 1-12
Power Safety ........................................................ VI System Map: Left View ......................................... 1-13
Battery Precautions .............................................VII System Map: Right View ....................................... 1-14
Cleaning ............................................................ VIII System Map: Bottom View .................................... 1-15
Servicing ........................................................... VIII Windows XP Start Menu & Control Panel ............ 1-16
Travel Considerations .......................................... IX Video Features ....................................................... 1-17
Display Devices & Options ................................. 1-19
Quick Start Guide Power Management Features ................................. 1-20
Overview ..................................................................1-1
Model Differences ..................................................1-2 Features & Components
Advanced Users .....................................................1-4 Overview .................................................................. 2-1
Beginners and Not-So-Advanced Users .................1-4 Hard Disk Drive ....................................................... 2-2
Warning Boxes .......................................................1-4 Optical (CD/DVD) Device ...................................... 2-3
Not Included ...........................................................1-5 Loading Discs ........................................................ 2-3
System Software .....................................................1-5 Handling CDs or DVDs ......................................... 2-4
System Startup ..........................................................1-6 DVD Regional Codes ............................................ 2-5
System Map: Model A - Top View 4-in-1 Card Reader ................................................... 2-6
with LCD Panel Open ..............................................1-7 PC Card Slot ............................................................ 2-7
System Map: Model B - Top View Inserting and Removing PC Cards ........................ 2-7
with LCD Panel Open ..............................................1-8 Auto Mail Checker ................................................... 2-8
LED Indicators .........................................................1-9 Application Hot-Key .............................................. 2-10
XIII

16. Preface
TouchPad and Buttons/Mouse ...............................2-11 Battery Life ........................................................... 3-9
Configuring the TouchPad and Buttons ..............2-11 Recharging the Battery with the AC/DC Adapter 3-10
Audio Features .......................................................2-12 Proper handling of the Battery Pack ................... 3-11
8 Channel Sound Support ...................................2-13 Battery FAQ ........................................................ 3-12
Adding a Printer .....................................................2-14 Swap Battery (Optional) ........................................ 3-13
USB Printer .........................................................2-14
Parallel Printer .....................................................2-14
Drivers & Utilities
What to Install .......................................................... 4-1
Power Management Module Driver Installation .................................... 4-1
Overview ..................................................................3-1 Service Packs ......................................................... 4-3
Advanced Configuration and Power Interface .......3-1 Authorized Driver Message ................................... 4-4
The Power Sources ...................................................3-2 Version Conflict Message ..................................... 4-4
AC/DC Adapter ......................................................3-2 Updating/Reinstalling Individual Drivers ............. 4-4
Battery ....................................................................3-2 Driver Installation .................................................... 4-5
Turning on the Computer .........................................3-3 Driver Installation Procedure ................................. 4-6
Power Schemes ........................................................3-4 New Hardware Found ............................................ 4-6
System Power Options .............................................3-6 Service Pack Installation ....................................... 4-6
Hibernate Mode vs. Shutdown ...............................3-6 Manual Driver Installation ................................... 4-7
Standby Mode vs. Hibernate Mode ........................3-6 New Hardware Found ............................................ 4-7
Standby ..................................................................3-7 Chipset (WinXP) .................................................. 4-8
Hibernate ...............................................................3-7 Video (WinXP) ..................................................... 4-8
Configuring the Power Button .................................3-8 Audio (WinXP) .................................................... 4-8
Battery Information ..................................................3-9 LAN (WinXP) ...................................................... 4-9
New Battery ..........................................................3-9 Modem (WinXP) .................................................. 4-9
XIV

17. Preface
TouchPad (WinXP) .............................................4-10 Large Disk Access Mode (Advanced Menu) ........... 5-9
PCMCIA/Card Reader (WinXP) ........................4-10 Local Bus IDE adapter (Advanced Menu) .............. 5-9
Hot-Key (WinXP) ...............................................4-11 Legacy USB Support (Advanced Menu) ................. 5-9
AutoMail (WinXP) .............................................4-11 Summary Screen: (Advanced Menu) ....................... 5-9
Wireless LAN .....................................................4-12 Boot-time Diagnostic Screen: (Advanced Menu) .... 5-9
Bluetooth .............................................................4-12 Security Menu ........................................................ 5-10
PC Camera ..........................................................4-12 Set Supervisor Password (Security Menu) ............ 5-10
Port Replicator ....................................................4-12 Set User Password (Security Menu) ...................... 5-11
Password on boot: (Security Menu) ....................... 5-11
BIOS Utilities Boot Menu ............................................................. 5-12
Overview ..................................................................5-1 Exit Menu .............................................................. 5-14
The Power-On Self Test (POST) .............................5-2
Failing the POST ....................................................5-3 Upgrading The Computer
Fatal Errors ............................................................5-3 Overview .................................................................. 6-1
Non-Fatal Errors ...................................................5-3 When Not to Upgrade ............................................ 6-2
The Setup Program ...................................................5-4 Removing the Battery .............................................. 6-3
Entering Setup ........................................................5-4 Upgrading the Hard Disk Drive ............................... 6-5
Setup Screens .........................................................5-5 Upgrading the Optical (CD/DVD) Device .............. 6-8
Main Menu ...............................................................5-6 Upgrading the System Memory (RAM) .................. 6-9
System Time & Date (Main Menu) ..........................5-6 Upgrading the Processor ........................................ 6-12
IDE Channel 0 Master/Slave (Main Menu) .............5-7
System/Extended Memory (Main Menu) .................5-7 Modules & Options
Advanced Menu .......................................................5-8 Overview .................................................................. 7-1
Installed O/S: (Advanced Menu) ..............................5-8 Intel PRO/Wireless Mini-PCI WLAN Module ....... 7-2
Reset Configuration Data (Advanced Menu) ...........5-9
XV

18. Preface
Intel WLAN Driver Installation ............................7-3 Keyboard ................................................................ 8-12
Bluetooth Module .....................................................7-4 Operation ............................................................... 8-13
Bluetooth Driver Installation ................................7-4 Modules ................................................................. 8-14
PC Camera ................................................................7-6
Sertek PC Camera Driver Installation (WinXP) ...7-7 Interface (Ports & Jacks)
PC Camera Audio Setup .......................................7-8 Overview ................................................................. A-1
BisonCap ..............................................................7-10 Notebook Ports and Jacks ....................................... A-2
Eliminating Screen Flicker ..................................7-11 Built-In Microphone ............................................... A-2
Port Replicator ........................................................7-12 Card Reader Port ..................................................... A-2
Port Replicator Setup Instructions: .....................7-13 DC-In Jack .............................................................. A-2
Port Replicator Serial (COM) Port External Monitor (VGA) Port ................................. A-2
Driver (WinXP) ...................................................7-14 Headphone-Out Jack ............................................... A-2
Port Replicator Network (LAN) Line-In Jack ............................................................ A-2
Driver (WinXP) ...................................................7-14 Microphone-In Jack ................................................ A-3
Mini-IEEE 1394 Port .............................................. A-3
Troubleshooting RJ-11 Phone Jack .................................................... A-3
Overview ..................................................................8-1 RJ-45 LAN Jack ...................................................... A-3
Basic Hints and Tips ................................................8-2 Security Lock Slot .................................................. A-3
Backup and General Maintenance ............................8-3 S/PDIF-Out Jack ..................................................... A-4
Viruses ......................................................................8-4 S-Video-Out Port .................................................... A-4
Upgrading and Adding New Hardware/Software ....8-5 USB 2.0/1.1 Ports ................................................... A-4
Power ........................................................................8-7 Optional Port Replicator Ports and Jacks ............... A-5
Display .....................................................................8-9 DC-In Jack .............................................................. A-5
Boot Password ........................................................8-10 External Monitor (VGA) Port ................................. A-5
Audio & CD Device ...............................................8-11 Parallel Port ............................................................. A-5
XVI

19. Preface
Serial Port ................................................................A-5 Keyboard & Pointing Device ...................................C-3
RJ-45 LAN Jack ......................................................A-5 PCMCIA ..................................................................C-3
USB 2.0/1.1 Ports ....................................................A-6 Interface ...................................................................C-4
Card Reader .............................................................C-4
Intel Video Driver Controls Communication ........................................................C-4
Intel Video Driver Installation ................................ B-1 Power Management .................................................C-4
Dynamic Video Memory Technology ..................... B-2 Power .......................................................................C-5
Intel Graphics Properties ......................................... B-3 Environmental Spec .................................................C-5
Schemes ................................................................. B-5 Physical Dimensions & Weight ...............................C-5
Display Devices ....................................................... B-6 Optional ...................................................................C-5
Attaching Other Displays ........................................ B-7
Display Modes ......................................................... B-8
TV Settings ............................................................ B-12
Specifications
Processor ................................................................. C-2
Core Logic ............................................................... C-2
Memory ................................................................... C-2
Security .................................................................... C-2
BIOS ........................................................................ C-2
LCD ......................................................................... C-2
Video Adapter ......................................................... C-3
Storage ..................................................................... C-3
Audio ....................................................................... C-3
XVII

20. Preface
XVIII

21. Quick Start Guide
1
Chapter 1: Quick Start Guide
Overview
This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the
computer and to getting your system started. The remainder of the manual covers the following:
• Chapter 2 A guide to using some of the main features of the computer e.g. the storage devices (hard disk,
optical device, 4-in-1 card reader, PC Card), Auto Mail Program, Touch Pad & Mouse, Audio
& Printer.
• Chapter 3 The computer’s power saving options.
• Chapter 4 The installation of the drivers and utilities essential to the operation or improvement of some of the
computer’s subsystems.
• Chapter 5 An outline of the computer’s built-in software or BIOS (Basic Input Output System).
• Chapter 6 Instructions for upgrading your computer.
• Chapter 7 A quick guide to the computer’s Wireless LAN, Bluetooth, PC Camera and Port Replicator
modules (some of which may be optional depending on your purchase configuration).
• Chapter 8 A troubleshooting guide.
• Appendix A Definitions of the interface, ports/jacks which allow your computer to communicate with external
devices.
• Appendix B Information on the Intel Video driver controls.
• Appendix C The computer’s specification.
Overview 1 - 1

22. Quick Start Guide
1
Model Differences
This notebook series includes two different model types. The models differ slightly in design style including the
LCD type, and the location of the card reader. See Figure 1 - 1 below and Table 1 - 1, on page 1 - 3 for an outline
of the model differences.
Model A Model B
Figure 1 - 1 - Model Differences
1 - 2 Overview

23. Quick Start Guide
1
Feature Model A Model B
15.0” XGA (1024 * 768) TFT
LCD Type OR 14.0” WXGA (1280 * 768) TFT
15.0” SXGA+ (1400 * 1050) TFT
4-in-1 Card Reader Location Left Side Front
Hot-Key and Power Buttons
Table 1 - 1 - Model Differences
Overview 1 - 3

24. Quick Start Guide
1
Advanced Users
If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful
to refer to “What to Install” on page 4 - 1, “BIOS Utilities” on page 5 - 1 and “Upgrading The Computer” on
page 6 - 1 in the User’s Manual. You may also find the notes marked with a of interest to you.
Beginners and Not-So-Advanced Users
If you are new to computers (or do not have an advanced knowledge of them) then
Notes the information contained in the this Quick Start Guide should be enough to get you
up and running. Eventually you should try to look through all the documentation
Check the light colored
boxes with the mark (more detailed descriptions of the functions, setup and system controls are covered
above to find detailed in the remainder of the User’s Manual), but do not worry if you do not understand
information about the everything the first time. Keep this manual nearby and refer to it to learn as you go.
computer’s features. You may find it useful to refer to the notes marked with a as indicated in the mar-
gin. For a more detailed description of any of the interface ports and jacks see “In-
terface (Ports & Jacks)” on page A - 1.
Warning Boxes
No matter what your level please pay careful attention to the warning and safety information indicated by the
symbol. Also please note the safety and handling instructions as indicated in the Preface.
1 - 4 Overview

25. Quick Start Guide
1
Not Included
Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database pro-
grams) have their own manuals, so please consult the appropriate manuals.
System Software
Your computer may already come with system software pre-installed. Where this is not the case, or where you
are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win-
dows XP (Home & Professional Editions) operating system.
Drivers
If you are installing new system software, or are re-configuring your computer for a different system, you will need to install
the drivers listed in “Drivers & Utilities” on page 4 - 1. Drivers are programs which act as an interface between the com-
puter and a hardware component e.g. a wireless network module. It is very important that you install the drivers in the order
listed in Table 4 - 1, on page 4 - 6. You will be unable to use most advanced controls until the necessary drivers and util-
ities are properly installed. If your system hasn’t been properly configured (your service representative may have already
done that for you), refer to “What to Install” on page 4 - 1 for installation instructions.
Overview 1 - 5

26. Quick Start Guide
1
System Startup
1. Remove all packing materials.
2. Place the computer on a stable surface.
3. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports.
4. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an
outlet, and connect the AC power cord to the AC/DC adapter (Note: If you have included the Port Replicator in
your purchase option see page 7 - 12).
5. Raise the lid/LCD (you will need to press the LCD latch to release
the lid of Model A computers) to a comfortable viewing angle, and
press the power button to turn the computer “on”.
6. Adjust the LCD panel to a comfortable viewing angle.
7. The LED Power & Communication indicators show the power and
battery status of the computer, and give notification of e-mail
received.
Figure 1 - 2 - Computer with AC/DC Adapter Plugged-In
Shutdown
Please note that you should always shut your computer down by choosing the Turn Off Computer command from the
Start menu in Windows. This will help prevent hard disk or system problems.
1 - 6 System Startup

27. Quick Start Guide
1
System Map: Model A - Top View with LCD Panel Open
1
1. Optional Built-In PC Camera
2. LCD
Wireless Device 3. LED Status Indicators
Operation Aboard 4. Hot-Key Buttons
Aircraft 5. Power Button
The use of any portable
2 6. Keyboard
electronic transmission 7. Built-In Microphone
devices aboard aircraft is 8. TouchPad and Buttons
usually prohibited. Make
9. LED Power & Communication
sure the module(s) are
OFF if you are using the Indicators
computer aboard aircraft.
3 4 5
4
Use the key combinations
to toggle power to the 5
WLAN/Bluetooth mod-
ules, and check the status 6
indicator icon to see if the 3
modules are powered on
or not (see Table 1 - 3, on
page 1 - 9/Table 1 - 5, on
7
page 1 - 11).
8
9
Figure 1 - 3 - Model A - Top View with LCD Panel Open
System Map: Model A - Top View with LCD Panel Open 1 - 7

28. Quick Start Guide
1
System Map: Model B - Top View with LCD Panel Open
1. Optional Built-In PC Camera
1
2. LCD
3. Speaker Wireless Device
4. LED Status Indicators Operation Aboard
5. Hot-Key Buttons Aircraft
6. Power Button 2 The use of any portable
7. Keyboard electronic transmission
8. TouchPad and Buttons devices aboard aircraft is
9. LED Power & Communication usually prohibited. Make
sure the module(s) are
Indicators
OFF if you are using the
10. Built-In Microphone 3 computer aboard aircraft.
4 5 6
Use the key combinations
to toggle power to the
WLAN/Bluetooth mod-
5 6 7 ules, and check the status
indicator icon to see if the
modules are powered on
or not (see Table 1 - 3, on
4
page 1 - 9/Table 1 - 5, on
page 1 - 11).
8
9 10
Figure 1 - 4 - Model B - Top View with LCD Panel Open
1 - 8 System Map: Model B - Top View with LCD Panel Open

29. Quick Start Guide
1
LED Indicators Table 1 - 3 - LED Power & Communication Indicators
The two sets of LED indicators (LED Status Indica- Icon Color Description
tors and LED Power & Communication Indicators)
Green The Computer is On
on the computer display helpful information about the
current status of the computer. Blinking The Computer is in Standby
Green Mode
Table 1 - 2 - LED Status Indicators
The AC/DC Adapter is Plugged
Icon Color Description Orange In & the Computer is Powered
Off
Number Lock Activated (to activate
Green The AC/DC Adapter is Plugged
press Fn & NumLk) Orange
In & the Battery is Charging
Green Caps Lock Activated Blinking The Battery has Reached
Orange Critically Low Power Status
Scroll Lock Activated (to activate
Green Green The Battery is Fully Charged
press Fn & ScrLk)
Blinking
New Mail Has Arrived
Green
Green Hard Disk Activity
Swap Battery
The icon will provide additional information on The WLAN Module is Powered
Green
the optional swap battery status (optional for Model On
A computers only). See “Swap Battery (Optional)” The Bluetooth Module is
on page 3 - 13 for details. Orange
Powered On
LED Indicators 1 - 9

30. Quick Start Guide
1
Hot-Key Buttons & Keyboard The keyboard has an embedded numerical keypad for
easy numeric data input, and features Function Keys to
These buttons give instant access to the default Inter- allow you to change operational features instantly (see
net browser and e-mail program, and to a user-defined Figure 1 - 5).
application, with one quick button press. To use the
“user-defined application Hot-Key Button”, you must Function Keys
install the driver (see “Hot-Key (WinXP)” on page 4 - NumLk &
ScrLk Keys
11). Numeric
Keypad
Table 1 - 4 - Hot-Key Buttons
Hot-Key Function
Fn Key
Activate the user specified application e.g.
Figure 1 - 5 - Keyboard
Microsoft Word or Excel
Activate the Default E-Mail Program
Activate the Default Internet Browser Other Keyboards
If your keyboard is damaged or you just want to make
See “Application Hot-Key” on page 2 - 10 for config- a change, you can use any standard USB keyboard.
uration instructions. The system will detect and enable it automatically.
However special functions/hot keys unique to the sys-
tem’s regular keyboard may not work.
1 - 10 Hot-Key Buttons & Keyboard

31. Quick Start Guide
1
Function Keys
To use the function keys, press and hold the Fn key, then press the appropriate function key (F3 - F12 etc.).
Key Function Key Function
Fn Function Key Fn + F9 Increase LCD Brightness
Fn + F3 Mute Toggle Fn + F10 PC Camera Power Toggle
Fn + F4 Sleep Toggle Fn + F11 Wireless Power Toggle
Fn + F5 Decrease Audio Volume Fn + F12 Bluetooth Power Toggle
Fn + F6 Increase Audio Volume Fn + NumLk Number Lock Toggle
Fn + F7 Display Toggle Fn + ScrLk Scroll Lock Toggle
Fn + F8 Decrease LCD Brightness
Table 1 - 5 - Function Keys
Special Characters
Some software applications allow the number-keys to be used with Alt to produce special characters. These special char-
acters can only be produced by using the numeric keypad. Regular number keys (in the upper row of the keyboard) will
not work. Make sure that NumLk is on.
Function Keys 1 - 11

32. Quick Start Guide
1
System Map: Front & Rear Views
Figure 1 - 6
Model A
Front & Rear Views
1 2
1. LED Power &
Communication
Indicators Model B
2. LCD Latch (Model A
Only) 1 3
3. 4-in-1 Card Reader
(Model B Only)
4. External Monitor Port
5. S-Video-Out Port 8
6. RJ-11 Phone Jack 4 5 6 7
7. Security Lock Slot
8. Battery
4-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
1 - 12 System Map: Front & Rear Views

33. Quick Start Guide
1
System Map: Left View
Figure 1 - 7
Model A Left View
7
3 3 1. RJ-45 LAN Jack
4 5 6 8
1 2 2. Vent/Fan Intake
3. 2 * USB 2.0 Ports
4. S/PDIF-Out Jack
Model B
7 5. Line-In Jack
3 3 4 5 6 6. Mini-IEEE 1394 Port
1 2 7. PC Card Slot (see page
2 - 7)
8. 4-in-1 Card Reader
(Model A Only)
4-in-1 Card Reader
The card reader allows you to use the most popular digital storage card formats:
MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)
System Map: Left View 1 - 13

34. Quick Start Guide
1
System Map: Right View
Figure 1 - 8 - Right View
1. Headphone-Out Jack
2. Microphone-In Jack 3 3 4
1 2
3. 2 * USB 2.0 Ports 5
4. Optical Device Drive Bay (for CD/
DVD Device - see page 2 - 3)
5. DC-In Jack
Changing DVD Regional Codes
Go to the Control Panel and double-click System >
Hardware (tab), click Device Manager, then click
CD Emergency Eject the + next to DVD/CD-ROM drives. Double-click on
the DVD-ROM device to bring up the Properties di-
If you need to manually eject a CD/DVD (e.g. due to an unex- alogue box, and select the DVD Region (tab) to
pected power interruption) you may push the end of a straight- bring up the control panel to allow you to adjust the
ened paper clip into the emergency eject hole. Do not use a regional code (see “DVD Regional Codes” on
sharpened pencil or similar object that may break and become page 2 - 5).
lodged in the hole.
DVD region detection is device dependent, not OS-
Media Warning dependent. You can select your module’s region
code 5 times. The fifth selection is permanent. This
Don’t try to remove a floppy disk/CD/DVD while the system is cannot be altered even if you change your operating
accessing it. This may cause the system to “crash”. system or you use the module in another computer.
1 - 14 System Map: Right View

35. Quick Start Guide
1
System Map: Bottom View
2 Figure 1 - 9 - Bottom View
Model A
1. Vent/Fan Intake
CPU 1 2. Battery
The CPU is not a user ser- 3. Memory (RAM)/WLAN Module/CPU
viceable part. Opening this 3 Cover
compartment, or access- 4. Hard Disk Cover
ing the CPU in any way,
may violate your warranty. 4 2
Model B
Overheating
1
To prevent your computer
from overheating make 1
sure nothing blocks the 3
Vent/Fan Intake while the
computer is in use. 4
Battery Information
Always completely discharge, then fully charge, a new battery before using it. Completely discharge and charge the battery
at least once every 30 days or after about 20 partial discharges. See “Battery Information” on page 3 - 9 for full instruc-
tions.
System Map: Bottom View 1 - 15

36. Quick Start Guide
1
Windows XP Start Menu & Control Panel
Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are
accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk
drive, and a shortcut will usually be placed in the Start menu and/or the desktop. You can customize the look of
the Start menu by right-clicking the Start menu and selecting Properties from the menu.
Click here to toggle Category View
Figure 1 - 10 - Start Menu & Control Panel
In many instances throughout this manual you will see an instruction to open the Control Panel. The Control
Panel is accessed from the Start menu, and it allows you to configure the settings for most of the key features
in Windows (e.g. power, video, network, audio etc.). Windows XP provides basic controls for many of the fea-
tures, however many new controls are added (or existing ones are enhanced) when you install the drivers listed
in Table 4 - 1, on page 4 - 6. To see all controls it may be necessary to toggle off Category View.
1 - 16 Windows XP Start Menu & Control Panel

37. Quick Start Guide
1
Video Features
Your computer will have built-in Intel (Intel GMA 900) on-board video. You can switch display devices, and
configure display options, from the Display Properties control panel in Windows as long as the appropriate vid-
eo driver is installed. For more detailed video information see “Intel Video Driver Controls” on page B - 1.
To access Display Properties in Windows:
1. Click Start, point to Settings and click Control Panel (or just click Control Panel).
2. Double-click Display (icon) - In the Appearances and Themes category.
3. Click Settings (tab) in the Display Properties dialog box.
4. Move the slider to the preferred setting in Screen area/resolution 1 (Figure 1 - 11 on page 1 - 18).
5. Click the arrow, and scroll to the preferred setting In Colors/Color quality 2 (Figure 1 - 11 on page 1 - 18).
6. You can also access Display Properties by right-clicking the desktop and scrolling down and clicking
Properties. Click Settings (tab) and adjust as above.
7. Open the Display Properties control panel, and click Advanced (button) 3 (Figure 1 - 11 on page 1 - 18) to
bring up the Advanced properties tabs.
8. Click the Intel(R) Graphics Media Accelerator Driver tab, and click Graphics Properties (button) to make
any video adjustments you require.
Video Features 1 - 17

38. Quick Start Guide
1
1 2
3
Intel Display Properties
Figure 1 - 11 - Display Properties Desktop
1 - 18 Video Features

39. Quick Start Guide
1
Display Devices & Options
Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or
TV as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port, a TV to
the S-Video-Out Port. The following display modes are available (see “Intel Video Driver Controls” on page B
- 1 for details).
Intel Display Mode Description
Single Mode One of the connected displays is used as the display device
Intel(R) Dual Display Clone Mode Both connected displays output the same view and may be configured independently
Extended Desktop Mode Both connected displays are treated as separate devices, and act as a virtual desktop
Table 1 - 6 - Display Options
Intel Display Note
Note that the monitor is the default Primary display device in both Intel(R) Dual Display Clone Mode and Extended Desktop
Mode.
Video Features 1 - 19

40. Quick Start Guide
1
Power Management Features
The Power Options control panel icon in Windows (see page 1 - 16) allows you to configure power management
features for your computer. You may conserve power through individual components such as the monitor or hard
disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power
throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 - 12). Pay at-
tention to the instructions on battery care in “Battery Information” on page 3 - 9.
Figure 1 - 12 - Power Options
The computer’s power button, sleep button (Fn + F4 key combination), and lid (closing the lid) may be set to
send the computer in to either Standby or Hibernate mode.
Power Saving and Performance
Power Schemes may have an affect on your computer performance (see “Power Schemes” on page 3 - 4).
1 - 20 Power Management Features

41. Features & Components
Chapter 2: Features & Components 2
Overview
Read this chapter to learn more about the following main features and compo-
nents of the computer:
• Hard Disk Drive
• Optical (CD/DVD) Device
• 4-in-1 Card Reader
• PC Card Slot
• Auto Mail Checker
• Application Hot-Key
• TouchPad and Buttons/Mouse
• Audio Features
• Adding a Printer
Overview 2 - 1

42. Features & Components
2 Hard Disk Drive
The hard disk drive is used to store your data in the computer. The hard disk
Power Safety
can be taken out to accommodate other 2.5" parallel (PATA) hard disk drives
Before attempting to with a height of 9.5 mm.
access any of the inter-
nal components of The hard disk is accessible from the bottom of your computer as seen below.
your computer please For further details see “Upgrading the Hard Disk Drive” on page 6 - 5 .
ensure that the ma-
chine is not connected
to the AC power, and
that the machine is
turned off. Also ensure
Model A Model B
that all peripheral ca-
bles, including phone
lines, are disconnected
from the computer.
Figure 2 - 1
Hard Disk Location
Hard Disk
2 - 2 Hard Disk Drive

43. Features & Components
Optical (CD/DVD) Device 2
There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The ac-
Sound Volume
tual device will depend on the module you purchased (see “Storage” on
Adjustment
page C - 3). The optical device is usually labeled “Drive D:” and may be used
as a boot device if properly set in the BIOS (see “Boot Menu” on page 5 - 12). How high the sound
volume can be set de-
pends on the setting of
Loading Discs the volume control
To insert a CD/DVD, press the open button 1 and carefully place a CD/DVD within Windows. Click
onto the disc tray with label-side facing up (use just enough force for the disc the Volume icon on
the taskbar to check
to click onto the tray’s spindle). Gently push the CD/DVD tray in until its lock the setting (see “Au-
“clicks” and you are ready to start. The busy indicator 2 will light up while dio Features” on
data is being accessed, or while an audio/video CD, or DVD, is playing. If page 2 - 12).
power is unexpectedly interrupted, insert an object such as a straightened pa-
per clip into the emergency eject hole 3 to open the tray.
Figure 2 - 2
Optical Device
2 1 3
Optical (CD/DVD) Device 2 - 3

44. Features & Components
Handling CDs or DVDs
2 Proper handling of your CDs/DVDs will prevent them from being damaged.
CD Emergency Please follow the advice below to make sure that the data stored on your CDs/
Eject DVDs can be accessed.
If you need to manually Note the following:
eject a CD (e.g. due to
an unexpected power • Hold the CD or DVD by the edges; do not touch the surface of the disc.
interruption) you may
• Use a clean, soft, dry cloth to remove dust or fingerprints.
push the end of a
straightened paper clip • Do not write on the surface with a pen.
into the emergency • Do not attach paper or other materials to the surface of the disc.
eject hole. However • Do not store or place the CD or DVD in high-temperature areas.
please do NOT use a • Do not use benzene, thinner, or other cleaners to clean the CD or DVD.
sharpened pencil or
similar object that may
• Do not bend the CD or DVD.
break and become • Do not drop or subject the CD or DVD to shock.
lodged in the hole.
Disk Eject Warning
Don’t try to remove a
CD/DVD while the sys-
tem is accessing it.
This may cause the
system to “crash”.
2 - 4 Optical (CD/DVD) Device

45. Features & Components
DVD Regional Codes
To change the DVD regional codes see “Changing DVD Regional Codes” on
2
page 1 - 14.
.
DVD Regional Coding
Table 2 - 1
Region Geographical Location DVD Regional Coding
1 USA, Canada
Western Europe, Japan, South
2
Africa, Middle East & Egypt
Figure 2 - 3
South-East Asia, Taiwan, DVD Regions
3 South Korea, The Philippines,
Indonesia, Hong Kong
South & Central America,
4 Mexico, Australia,
New Zealand
N Korea, Russia, Eastern
5
Europe, India & Most of Africa
6 China
Optical (CD/DVD) Device 2 - 5

46. Features & Components
2 4-in-1 Card Reader
The card reader allows you to use some of the latest digital storage cards. Push
Card Reader Cover
the card into the slot and it will appear as a removable device, and can be ac-
Make sure you keep cessed in the same way as your hard disk (s). Make sure you install the PCM-
the cover in the card CIA/Card Reader Card driver (see “PCMCIA/Card Reader (WinXP)” on
reader when not is page 4 - 10).
use. This will help pre-
vent foreign objects • MMC (MultiMedia Card)
and/or dust getting in
to the card reader.
• SD (Secure Digital)
• MS (Memory Stick)
• MS Pro (Memory Stick Pro)
Figure 2 - 4
Removable Disks
1. Card Reader
1
Model A (Left)
1
Model B (Front)
2 - 6 4-in-1 Card Reader

47. Features & Components
PC Card Slot 2
The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC-
MCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Read- PC Card Slot Cover
er Card driver (see “PCMCIA/Card Reader (WinXP)” on page 4 - 10). Make sure you keep
the cover in the PC
Card slot when not is
Inserting and Removing PC Cards use. This will help pre-
• Align the PC Card with the slot and push it in until it locks into place. vent foreign objects
• To remove a PC Card, simply press the eject button 1 next to the slot. and/or dust getting in
to the PC Card Slot.
Figure 2 - 5
1 PC Card Slot
1
PC Card Slot 2 - 7

48. Features & Components
2 Auto Mail Checker
After you have installed the driver for the Auto Mail Checker program (see
“AutoMail (WinXP)” on page 4 - 11) you may then configure it to give you
notification when you receive new mail. You must be online to receive this
notification (note that this program only supports the POP3 protocol), and
your default mail program does not need to be open.
The Auto Mail Checker appears as an icon in the taskbar (if you do not
see the icon in the taskbar go to Start > Programs/All Programs > Auto
Mail Checker > Auto Mail Checker). Right clicking on the icon will bring
up the following options menu. If you have not input your mail account data,
then you will be prompted to do so.
Figure 2 - 6
Auto Mail Checker
Select Open to bring up the control panel for the program.
2 - 8 Auto Mail Checker

49. Features & Components
You may then configure the options for your mailserver, name, password, pro-
gram and method(s) of notification. 2
Note
Check with your Inter-
net Service Provider,
network administrator
or Mail Service provid-
er for details on what to
put on these pages.
Figure 2 - 7
Auto Mail Checker
Account Setup and
Options
Auto Mail Checker 2 - 9

50. Features & Components
2 Application Hot-Key
The hot-key buttons give instant access to the default Internet browser and e-
Application.exe mail program, and to a user-defined application, with one quick button press.
You will need to locate To configure a program to open when the application hot-key is pressed
the actual application (Windows Media Player is the default program), follow the instructions be-
executable (.exe) file, low.
not just the shortcut.
To find the application 1. Right click the Hot-Key driver icon in the taskbar.
right-click its shortcut 2. Select Setup from the menu, scroll to Application 1 and press Enter.
on the desktop and
click Properties. Click
the shortcut (tab) and
see where the execut-
able file is located by
clicking the Find Tar- 3. An Open dialog box will appear on the screen.
get (button).
Figure 2 - 8
Hot-Key
Configuration
Screens
4. Browse to the directory where the desired application.exe (see the sidebar)
program exists.
5. Double-Click on the program file or choose Open.
2 - 10 Application Hot-Key

51. Features & Components
TouchPad and Buttons/Mouse 2
The TouchPad is an alternative to the mouse; however, you can also add a
mouse to your computer through one of the USB ports. The TouchPad buttons Mouse Driver
function in much the same way as a two-button mouse. The central button may If you are using an ex-
be configured to function as you require. ternal mouse your op-
erating system may be
able to auto-configure
Configuring the TouchPad and Buttons your mouse during its
Once you have installed the TouchPad driver you can configure the functions installation or only en-
by double-clicking the TouchPad driver icon on the taskbar, or by going able its basic functions.
Be sure to check the
to the Mouse control panel in Windows (Start menu and point to Settings and device’s user docu-
click Control Panel, then double-click the Mouse icon). In Windows XP the mentation for details.
Mouse control panel is in the Printers and Other Hardware Category.
Figure 2 - 9
Mouse Properties
TouchPad and Buttons/Mouse 2 - 11

52. Features & Components
2 Audio Features
You can configure the audio options on your computer from the Sounds and
Sound Volume
Adjustment
Audio Devices Windows control panel, or from the Sound Effect Man-
ager icon in the taskbar/control panel (this will bring up the Realtek Audio
How high the sound Configuration menus). The volume may also be adjusted by means of the Fn
volume can be set de-
+ F5/F6 key combination.
pends on the setting of
the volume control
within Windows. Click
the Volume icon on the
taskbar to check the
setting.
Figure 2 - 10
Realtek Audio
Configuration
Menus
2 - 12 Audio Features

53. Features & Components
8 Channel Sound Support
If you wish to configure your system for 8 channel sound support, then the fol-
2
lowing ports should be used as outputs. Double-click the appropriate icon
(e.g. ) to bring up the “Connected device:” dialog box to configure the
output port.
• Side Speaker Out - Connect to S/PDIF Out
• Center/Subwoofer Speaker Out - Connect to Microphone In
• Front Speaker Out - Connect to Speaker/Headphone Out Figure 2 - 11
• Rear Speaker Out - Connect to Line In 8 Channel Sound
Support
Audio Features 2 - 13

54. Features & Components
2 Adding a Printer
The most commonly used peripheral is a printer. The following conventions
Parallel Printer will help you to add a printer, however it is always best to refer to the printer
After setting up the manual for specific instructions and configuration options.
printer attach the paral-
lel cable to the printer. USB Printer
Connect the printer’s Most current printers have a USB interface connection. You may use any one
parallel cable to the of the ports to connect the printer.
Parallel to USB con-
verter, and then plug Install Instructions:
the converter into the 1. Set up the printer according to its instructions (unpacking, paper tray, toner/
USB port. ink cartridge etc.).
2. Turn ON the computer.
Turn ON the printer,
3. Turn ON the printer.
then turn ON the com-
4. Connect the printer’s USB cable to one of the USB ports on the computer.
puter.
5. Windows will identify the printer and either load one of its own drivers or
Windows will identify ask you to supply one. Follow the on-screen instructions.
the printer and either
load one of its own Parallel Printer
drivers or ask you to
supply one. Follow the This is still a very common type of printer. The install instructions are in the
on-screen instructions. sidebar. Note: If you have included the Port Replicator in your purchase op-
tion, then a parallel port will be available, otherwise you will need to purchase
a parallel to USB converter.
2 - 14 Adding a Printer

55. Power Management
Chapter 3: Power Management
OS Note
Overview 3
Power management
To conserve power, especially when using the battery, your computer uses the functions will vary
ACPI power management system. Power management conserves power by slightly depending on
controlling individual components of the computer (the monitor and hard disk your operating system.
drive) or the whole system. This chapter covers: For more information it
is best to refer to the
• The Power Sources user’s manual of your
• Turning on the Computer operating system.
• Power Schemes (Note: All pictures
• System Power Options used on the following
• Configuring the Power Button pages are from the
• Battery Information Windows XP OS.)
• Swap Battery (Optional)
Advanced Configuration and Power Interface
The ACPI interface provides the computer with enhanced power saving tech-
niques and gives the operating system (OS) direct control over the power and
thermal states of devices and processors. For example, it enables the OS to set
devices into low-power states based on user settings and information from ap-
plications. ACPI is fully supported in Windows XP.
Overview 3 - 1

56. Power Management
The Power Sources
The computer can be powered by either an AC/DC adapter or a battery pack.
Port Replicator AC/
3 DC Adapter
AC/DC Adapter
You will be provided
Use only the AC/DC adapter that comes with your computer. The wrong type
with a 90W AC/DC
adapter if you pur- of AC/DC adapter will damage the computer and its components.
chase the port replica-
1. Attach the AC/DC adapter to the DC-in jack on the right of the computer.
tor option.
2. Plug the AC power cord into an outlet, and then connect the AC power cord
If you are using the to the AC/DC adapter (see sidebar if you are using the optional Port
computer with the Port Replicator).
Replicator, then you 3. Raise the lid/LCD to a comfortable viewing angle.
must use the 90W 4. Press the power button to turn “On”.
AC/DC adapter to
power the port replica-
tor and computer (DO Battery
NOT USE the com- The battery allows you to use your computer while you are on the road or
puter’s 65W AC/DC when an electrical outlet is unavailable. Battery life varies depending on the
adapter to power the
Port Replicator). See applications and the configuration you're using. To increase battery life, let
“Port Replicator” on the battery discharge completely before recharging (see “How do I com-
page 7 - 12 for more pletely discharge the battery?” on page 3 - 12).
information.
We recommend that you do not remove the battery. For more information on
the battery, please refer to “Battery Information” on page 3 - 9.
3 - 2 The Power Sources

57. Power Management
Turning on the Computer
Now you are ready to begin using your computer. To turn it on simply press
Shutdown
the power button on the front panel. 3
Note that you should
When the computer is on, you can use the power button as a Standby/Hiber- always shut your com-
puter down by choos-
nate/Shutdown hot-key button when it is pressed for less than 4 seconds
ing the Turn Off
(pressing and holding the power button for longer than this will shut the com- Computer command
puter down). Use Power Options in the Windows control panel to configure from the Start menu in
this feature. Windows. This will
help prevent hard disk
or system problems.
Forced Off
If the system “hangs”, and the Ctrl + Alt + Del key combination doesn’t work, press
the power button for 4 seconds, or longer, to force the system to turn itself off.
Power Button as Standby or Hibernate Button
If you are using a fully ACPI-compliant OS, (such as Windows XP) you can use the
OS’s “Power Options” control panel to set the power button to send the system into
Standby or Hibernate mode (see your OS’s documentation, or “Configuring the
Power Button” on page 3 - 8 for details).
Turning on the Computer 3 - 3

58. Power Management
Power Schemes
You can set your computer to conserve power through individual components
Resuming
3 by means of Power Schemes. You can also adjust the settings for each
Operation
scheme to set the monitor to turn off after a specified time, and the computer's
The system can re- hard disk motor to turn off if the hard disk drive has not been accessed for a
sume from Monitor or specified period of time (if the system reads or writes data, the hard disk motor
Hard Disk Standby by
pressing the Sleep/
will be turned back on). The schemes may also be set to set a specified time
Resume key combina- for the system to enter Standby or Hibernate modes (see “System Power Op-
tion (Fn + F4), or pow- tions” on page 3 - 6).
er button.
Figure 3 - 1
Power Schemes
3 - 4 Power Schemes

59. Power Management
Each Windows Power Scheme will also adjust the processor performance of
your machine in order to save power. This is worth bearing in mind if you are
experiencing any reduced performance (especially under DC/battery power).
3
Choose the Home/Office Desk scheme for maximum performance when the
computer is powered from an AC power source. Choose the Max Battery
scheme (bear in mind that this scheme may slow down the overall perfor-
mance of the computer in order to save power) for maximum power saving
when the computer is battery (DC power) powered. Windows will use Porta-
ble/Laptop as the default scheme.
Windows will use Portable/Laptop as the default scheme.
Power Schemes 3 - 5

60. Power Management
System Power Options
You can use the system power options to stop the computer’s operation and
3 restart where you left off. This system features Standby and Hibernate sleep
mode levels (Hibernate mode will need to be enabled by clicking the option
in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on
page 3 - 7).
Hibernate Mode vs. Shutdown
Hibernate mode and Shutdown are the same in that the system is off and you
need to press the power button to turn it on. Their main difference is:
When you come back from hibernation, you can return to where you last left
off (what was on your desktop) without reopening the application(s) and
file(s) you last used.
You can use either method depending on your needs.
Standby Mode vs. Hibernate Mode
If you want to stay away from your work for just a while, you can put the sys-
tem on standby instead of in hibernation. It takes a longer time to wake up the
system from Hibernate mode than from Standby mode.
3 - 6 System Power Options