The document outlines methods for collecting vegetation plot data, including locating and establishing plots, point intercept sampling, using a basal wedge, and collecting a structural summary and general site information. Key steps include setting up a grid system to locate plots within communities, taking point intercept readings along transects to measure vegetation cover, using a basal wedge to estimate basal area, and summarizing the dominant growth forms, heights, and species in each vegetation stratum.
Call Girl Nagpur Roshni Call 7001035870 Meet With Nagpur Escorts
Ausplots Training - Session 3
1.
2. The “After Lunch” Session 3
( we’ll be watching for anyone nodding off!)
Topics to cover:
Locating the plot/ plot layout/Positioning
Point Intercept
Basal wedge
Vegetation
Structural Summary
General Site info
18. Where to put sites
•Homogeneous or constantly mixed (Veg, Slope, relief, soil)
•Aligned to grid
•100x100 (1ha)
•Avoid roads, cattleyards, fences, bores etc.
•Consider access nowand in the future
20. Naming Conventions
A AusPlots
T Transects
L LTERN
S Supersites
G General use
TRA Training
Australian Capital Territory CT
New South Wales NS
Northern Territory NT
Queensland QD
South Australia SA
Tasmania TC
Victoria VC
Western Australia WA
Arnhem Coast ARC
Arnhem Plateau ARP
Broken Hill Complex BHC
Burt Plain BRT
Cape York Peninsula CYP
Carnarvon CAR
Central Arnhem CA
Central Kimberley CK
Central Ranges CR
Two Letters for State, One letter for Type –Three letters for Bioregion –Four numbers to identify the plot number.
Here would be:
SAS-MDD-0001 (South Australia Supersites –Murray Darling Depression –plot #1)
State Code:
Plot Type:
Bioregion code:
21. Using the DGPS: an Overview
•Turn on and connect both units
•Well before you intend to use
•Remember to charge batteries
22. Actual process will be run through in the field.
Process involves
–Ensuring set up is correct
–Taking a reference point
–Placing a pre-determined grid over the reference point
–Using the grid to peg out the plot corners, transect ends and the centre point.
–Recording all of these points
–Downloading them in the office
29. Point intercept
•An repeatable objective quantitative measure of both vegetation presence, and percentage cover within the quadrat
•Essential to determine change
•Based on a huge number of references
–All agree 1000pts minimum
•10 x 100m transects with a sample every 1 m
–5 transects N-S, 5 transects E-W
30. Laying out the measuring tape between the transect end pegs
First point taken at the ‘0’ Meter mark
32. Assesses canopy cover above the device
Indicates height
Assesses Cover below the device
Field Cover Assessment Device
(Gandalf’s Staff)
Any vegetation touching the device between the laser pointer and the densitometer is also included
33. In this example the substrate is litter as that is what the laser is intersecting
Height is read from the staff
34. Assessing Cover above the device
•Uses a densitometer
•Ensure the device is level using the bubble level
•Use the cross hairs and small circle to identify what is intersected.
35. The Concept of “In Canopy –Sky”
•Needed so that the data is readily convertible between ‘Opaque Canopy Cover’ And ‘Foliage Projective Cover’(FPC)
•Makes the same data useful for more applications
•Opaque canopy cover assumes that the canopy is solid
•FPC only counts cover where the vertical projection of foliage obscures the ground.
•Uses the densitometer
36. In Canopy Sky
A Vegetation Intersect
for Eucalyptus Sp.
“In Canopy-Sky”
for Eucalyptus Sp.
51. Basal area
•A plotlessmeasure
•Works on a Circular Plot assessing circular trunks
•Works plotlesslybecause the area of the plot varies at the same RATE as the increase in basal area needed to get a hit with increasing distance. (Area of plot V’s area of Basal area)
•Calculations a little complex
•Well accepted and rapid method.
52. •For a given basal area factor.
•Take the number of “hits”
•Multiply by the basal area factor
•Answer in M2/ha
53. •At 9 points within quadrat
•Conduct test sweep to determine BAF (basal area factor)
•Aim to have at least 7 hits per species
•If more than 15-20 Consider using a larger aperture wedge
•AusPlots have had Basal Wedges made up that include a wide range of BAF’s for use in a wide range of ecosystems
•This wedge has been designed to work with a string length of 50cm
54. •Place the String Knot (indicates 50cm) directly underneath you preferred eye.
•Sight through a wedge gap
•Spin on the spot through 360 degrees ensuring you are aware of your start point.
•Possible (but unlikely) to have different BAF for different species at the one sweep point.
•Rotate the wedge to determine the appropriate BAF for your environment.
Squinting definitely helps you to look this silly!
55. The tree is clearly wider than the wedge aperture –This is counted as a hit of 1
The tree is exactly the same width as the wedge aperture –This is counted as a hit of 0.5
The tree here is clearly narrower than the wedge aperture –this is not counted as a hit at all.
58. •Aim to be able to create level 5 NVIS – Association Level
–Requires Dominant Growth Form, height, Cover and species (3) for the three traditional strata (Upper, Mid and Ground)
–Much of this information is already collected within the method/on the app
–Only need to collect the interpretive information that not collected elsewhere.
59. •Collect –Dominant 3 species in each strata in the app in decreasing order of cover.
•This info then used to query other components of the data
–Calculate Cover for each of the species
–Calculate average height for that species in the strata.
–Determine dominant growth form for that species at that site.
–Use height profiles to confirm strata.
67. The bare basics!
•To provide data context
•Observers
•Plot ID e.g. SAA-STP-00001
•IBRA Bioregion
•Date
•MGA & datum
•Grid layout/alignment
•Mud map
68. The bare basics!
•Landform pattern
•Landform element
•Site slope (degrees from horizontal)
•Site Aspect (degrees from north)
•Outcrop lithologye.g. Quartzite
•Surface strew size
•Location comments and general comments .e.g. recent rain
