CoFold is the ultimate in exterior folding systems and opens up a wealth of new design possibilities.
The CoFold System has been designed to maximise the flexibility of a room’s living space, removing barriers and enabling the user to have an indoor/outdoor experience by fully opening up exterior walls.
The system which operates with effortless ease combines the benefits of folding doors with the ability to keep out the weather with no corrosion worries. This modern, contemporary feature will increase available living space whilst allowing natural light to envelop the room.
System Capacity
Maximum leaf height - 3300mm
Maximum leaf weight - 100kg
Maximum leaf width - 1000mm
Leaf thickness - 35-68mm*
* For thicker or thinner doors please contact Coastal Technical Team
For doors between 35-47mm use an alternative flush bolt
Applications
Residential and commercial timber exterior folding applications
Specially suited to coastal environments made from 316 stainless steel.
End folding timber doors folding to one or both sides
Standard folding configuration features doors folding outward.
Inward folding doors can be used where the doors are not directly
exposed to the weather.
Premium security features
Recognised weather resistance
The folding unit is not hinged to post, but is pivoted in the track and floor. All door leaves are of equal width. A swing leaf can be included by incorporating an odd number of leaves. For full weather protection, doors, frame and track should incorporate the seals provided in the CoFold range.
Cill and frame construction should be in accordance with the CoFold fixing instructions. Intermediate hangers and hinges are non rebated.
www.coastal-group.com
2023 - Between Philosophy and Practice: Introducing Yoga
CoFold Non-Mortice Sliding Folding Door Gear Installation Instructions
1. 1
CoFold Non-Mortice
Fitting Instructions
Diagram 1
for top hung exterior folding doors
SYSTEM CAPACITY
Maximum leaf height
Maximum leaf weight
Maximum leaf width
Maximum leaf thickness
- 3300mm
- 100kg
- 1000mm
- 35-68mm*
*For thicker or thinner doors please contact technical@coastal-group.com.
**For doors between 35-44mm an alternative to the CoFold flushbolt is required.
SFW1
INSIDE
OUTSIDE
SFW2
Diagram 2
JAMB CAP
IN LINE WITH
TRACK
Diagram 3
SFW1
SFW2
SFW2
Diagram 4
SFW1
34
140
WHEN USED IN CONJUNCTION WITH
ALUMINIUM SUPPORT CHANNEL 94SC
THE OUTER CHANNEL DIMENSIONS
BECOME 23H x 25W
JAMB CAP IN LINE WITH TRACK
JAMB CAP GASKET
52
39
212
ALTERNATIVE ALUMINIUM THRESHOLD SF94T
SUPPLIED BY COASTAL - COMES COMPLETE
WITH 94P AND ENDCAPS AND IS PREDRILLED
FOR DRAINAGE. REFER TO PAGE 9
SFW9
2. INTERMEDIATE
HANGER SET KIT
SFW4
2
PREPARATION
SFW1 SFW2R SFW2L SF3 SF4 SF5 SF6 SF7 SFW8 SFW9 SF10 -
Pivot Assembly Set
End Hanger Set Right Hand
End Hanger Set Left Hand
Hinge Set with Handle
Intermediate Hanger Set
Hinge Set Inward Opening
Hinge Set Offset Inward Opening
Hinge Set Offset Outward Opening
Rebated End Hanger Meeting
Pivot Hinge for Doors Over 2200mm High
Face Fix Handle (Optional)
END HANGER SET KIT
SFW2L
SFW2R
PIVOT SET KIT
SFW1
SFW9
(OPTIONAL)
Diagram 5
Diagram 6
SFW1
SFW2L
SFW1
SFW2L
SFW1 SFW1
SF4
SFW1
SFW8
SFW1
SFW1
SF4
SFW1
SF4
SFW1
SFW1
SF4
SFW2L
SFW1
SF4
SFW2L
SFW1
SF4
SF4
SFW1
SFW2R
SFW1
SFW2R
SFW1
SFW1
SFW1
SFW8
SFW1
SFW1
SF4
SFW1
SF4
SFW1
SFW1
SF4
SFW1
SF4
SFW2R
SFW1
SFW2R
SFW1
SF4
SF4
SF4
SFW1
SFW1
SFW1
SF4
SFW8
SFW1
SFW1
SFW1
SF4
SF4
SFW1
SFW1
SF4
SF4
SFW2L
SF4
SFW2L
SFW1
SF4
SF4
SFW1
SFW1
SFW2R
SF4
SFW1
SF4
SFW8
SFW1
SFW1
SFW1
SF4
SF4
SFW1
SFW1
SF4
SF4
SFW2R
3. 3
Preparing the opening
Ensure the opening is square and all load bearing areas are suitable for the weight of the system. Take particular care to ensure there is
sufficient strength in the structure above the opening to take the concentrated weight of the doors, when in the open stacked position.
The CoFold system provides +/- 3mm of horizontal and vertical adjustment. Use a plumb line to ensure that the centre line of the track
and the centre line of the channel are offset by 19mm.
Diagram 8
OR USE ALUMINIUM
THRESHOLD BY COASTAL
Diagram 9
Diagram 7
Preparing the door frame
FRAME AT HEAD
FRAME CORNERS
OPTIONAL SFW9
Refer to page 10
Diagram 10
4. 4
Preparing the door leaves
Door leaf width calculation
1. Decide how many door leaves you want in the opening.
2. Add together all the 3mm clearances required between door leaves and the jambs (there will be one more than the number of door
leaves). This is the total clearance figure.
3. Measure the finished opening width (W) and deduct from this the total clearance figure.
4. Divide this new figure (finished opening width minus total clearance) by the number of doors to produce the actual door width. (N.B.
all doors with the CoFold system are the same width).
For example: For a 4 door leaf system with a finished opening width of 2345mm the door leaf width would be 2345mm minus (3x3mm)
+(2x6mm) divided by 4 (number of door leaves) = 581mm.
Door leaf height calculation
Leaf height = finished opening height (see diagram 7) minus 66mm.
Diagram 11
PREPARING THE DOOR LEAF
AT THE JAMB
BETWEEN DOOR EDGES
Door Seals
Prepare the door leaves to accept the
AQ63B seal.
Diagram 12
Add 10mm to the
width of each leaf
to create rebate
END
HANGER
LEAF
21
6
Add 10mm to the
width of each leaf
to create rebate
END
HANGER
LEAF
11 11
21
END
HANGER
LEAF
6
6
SWING
LEAF
END
HANGER LEAF
END
HANGER
LEAF
3
SFW8 Meeting
door set
SFW2L End hanger
door set (Left)
11
SFW8 Meeting
door set
11
6
END
HANGER LEAF
SFW2L End hanger
door set (Left)
SWING
LEAF
Meeting Doors
Use the SFW8 set for 2+2, 4+4, plus
other multiples of rebated and square
edge timber door configurations.
Diagram 13
5. 5
Door hardware positioning
SFW9
KIT SFW1
KIT SF4
KIT SFW2L & KIT SFW2R
Diagram 14
7.5mm check In for SF1, SF2 and SF8
End door leaf preparation
Square edged timber door
Rebated meeting timber doors
25
25
20
10
20
100
100
Diagram 15
7. 7
INSTALLATION
1. Ensure that you have all the required parts. Unpack the
components and identify the parts. Lay the parts on the
ground in the same configuration as they will be when
installed. It is recommended that a light smear of general
purpose grease is applied to all bolts prior to assembly.
Diagram 17
2. Cut the track to the required length and pre-drill for
fixings in accordance with diagram 17. Please note that the
extra fixings are required where the doors stack together.
TOP PIVOT SECURING BLOCK
3. Cut the channel to the required length and fit in the sill.
Drill drainage holes (see diagram 1).
PIVOT SECURING BLOCK HEX
BOLTS
4. Remove all the wheel assemblies and pivot block from
the hanger and pivot bolts, and disassemble top pivot
block assembly.
PIVOT CAM
5. Slide the wheel assemblies and track pivot block into
the track in the correct order, orientation, and position
and fix the track in position. Reassemble top pivot block
assembly (see diagram 18).
PIVOT ADJUSTER
PIVOT CLAMP PLATE
6. Remove the bottom pivot assembly and guide roller
assembly (see diagram 19). Disassemble the bottom pivot
assembly.
ADJUSTMENT LOCK OFF
BOLTS
Diagram 18
7. For installation, assemble leaves in pairs via the hinges.
To improve the ease of installation pre-drill pilot holes for
all hinge parts. Fit kits SFW1, SF7,SF4 and SFW9
(optional) to first pair of leaves.
Please ensure all 4 screws are fixed per end hinge.
SFW1
SF7
SF4
8. Screw the bottom anchor of the bottom pivot assembly
to the base of the channel 14mm from the jamb. Please
note, the screw nearest the end of the bottom anchor is
closest to the jamb (see diagram 20). Reassemble the pivot
assembly leaving the clamping screws loose (see diagram 24).
9. Suspend pairs of leaves by engaging top pivot and
hanger bolts using 5mm allen key supplied (see top of
diagram 19).
10. Attach the bottom pivot and guide assembly to their
respective hinges, adjust the bottom pivot side plates
position so that it engages with the hinge bolt. Tighten
pivot and guide strap bolts (see diagram 21).
Diagram 19
11. Lift the next pair of leaves into position and support
their weight by screwing the hanger strap bolt into the
hanger wheel assembly and fixing the second and third
leaves together.
JAMB
CHANNEL
14
12. Continue this procedure until all leaves are fitted.
BOTTOM ANCHOR
Diagram 20
Diagram 21
8. 8
ADJUSTMENT
INSIDE
Height Adjustment (± 3mm)
1. Close leaves and adjust the door height to achieve an equal
gap between the top of the leaves and the track (a 9mm gap is
recommended). (see diagram 22).
LOCKING HANGER
GRUB SCREW
ON INSIDE OF DOOR
2. Once the adjustment is complete use the allen key to tighten
the locking hanger grub screw until secure.
Lateral Adjustment
1. With the unit still in the closed position, slide the set of
leaves towards the jamb to obtain the desired gap between the
jamb and the pivot door. A gap of 3mm is recommended using
the adjustment cam. Once in position tighten the clamp screws.
(see diagram 24).
2. Fold the leaves and adjust the bottom side plate using the
allen key provided so that the gap between the door and the
jamb is the same over the full length of the door.
3. Tighten the two clamping screws to lock the side plate to
the bottom anchor.
4. Once the pivot door is in the correct position insert and
tighten the locking pivot grub screw from the inside position. (as
shown in diagram 23)
SF4 ILLUSTRATED.
SAME METHOD OF
ADJUSTMENT APPLIED
TO SFW1, SFW2L, SFW2R
AND SFW8.
Diagram 22
INSIDE
CLAMP SCREW
LOCKING PIVOT
GRUB SCREW
ON INSIDE OF
DOOR
CARE AND MAINTENANCE
CLAMP SCREW
ADJUSTMENT CAM
Diagram 23
To provide years of trouble free operation, it is recommended
that the track is kept free from dirt and debris. Periodically
replace the general purpose grease on all bolts. To prolong the
appearance of the exposed hinge parts, it is recommended they
are periodically washed with soap and water. Maintenance is
required on all components including stainless steel to validate
manufacturers warranty. For further maintenance details please
refer to our website.
CLAMP SCREW
ADJUSTMENT CAM
CLAMP SCREW
BOTTOM ANCHOR
JAMB SIDE
BOTTOM SIDE
PLATE
ADJUSTMENT
Diagram 24
9. 9
Aluminium Threshold Jamb Kit
51
25.5
25.5
21
94
25
Jamb Cap
Jamb Cap Gasket
34
19
15
51
Threshold SF94T
8
27
2.5
Pre-drilled 10mm diameter drainage holes
at 300mm centres
Endcap
83
2.5
51
140
51
25.5
25.5
21
34
23
Jamb Cap
Jamb Cap
2.5
8
15
51
140
94
Jamb Cap Gasket
Jamb Cap Gasket
2.5
25
27
52
39
Endcap
Endcap
83
Jamb Cap
Jamb Cap Gasket
52
(All dimensions in mm)
39
Endcap
10. 10
SFW9 Intermediate Pivot Set
1. The CoFold SFW9 intermediate pivot set shown in Diagram 1, should
be fitted to the pivot door approximately mid way between the SFW1 top
and bottom pivot assemblies. The SFW9 hinge must be positioned on the
same centre line as the SFW1 top and bottom pivot hinge bodies.
6. Fit the SFW9 cover sleeve on to the SFW9 hinge body and drop the hinge
strap bolt into position, as shown in Diagram 4.
7. Screw the threaded link arm fully into the frame support plate. The
centre of the threaded hole in the link arm should be positioned to receive
the strap bolt. Screw the strap bolt in to the link arm until there is a 2mm
gap between the head of the strap bolt and the hinge body, as shown in
Diagram 4.
2. Prepare the frame for the opening by drilling a Ø12mm hole (as shown
in Diagram 3), ensuring that the centre point of the hole is 20mm lower
than the bottom of the hinge body as shown on Diagram 4. Rebate the
frame support plate, if required.
8. Adjust the SFW9 pivot set to ensure the clearance between the pivot door
and the frame is uniform (Diagram 5).
3. Screw the frame support plate on to the opening frame preparation, as
shown in Diagram 3.
Note: These fitting instructions should be used in conjunction with the
CoFold Fitting Instructions
4. Fit the pivot door into position using the SFW1 pivot set.
SFW1
Main strap bolt
SFW9
Hinge body
SFW1
Diagram 1.
Diagram 2.
ole
ph
dee
m
28m
Opening
frame
Ø12
28mm
Pilot holes
R12.5
Rebate details
see diagram 1
2.5
mm
dee
p
25mm
41m
m
Door in closed
position
Hole centre to
door face 8mm
Ø12
Diagram 3.
Door shown in the
open position
Door shown in the
open position
8mm
2mm gap
2mm gap
Main strap bolt
Adjustment:
3mm in to the frame
6mm out to the frame
Line from bottom
of the hinge body
20mm
Threaded link arm
Frame support plate
Diagram 4.
Diagram 5.
11. 11
Outward Opening Flush Bolt
For top hung exterior folding doors. For use in conjunction with standard outward opening fitting
instructions. Follow routing instructions for the bolt keep and flush bolt length to be fitted, fit both with
the screws supplied. Suitable pilot holes for screws are recommended.
Routing detail for
450mm Top Flush Bolt
Routing detail for
600mm Top Flush Bolt
HEAD BOARD
LINTEL
12.5
FASCIA
Routing detail for
190mm Top Flush Bolt
18
Routing detail for
190mm Bottom
Flush Bolt
PLATE
600
450
580
190
430
170
30
INSIDE
4
190
Enlarged detail showing the
sectional routing dimensions
for all 3 bolt sizes
40
OUTSIDE
170
TOP FLUSH
BOLT
22
17
Note:
Routing detail is the
same for both locking
and non-locking flush
bolts.
Door height
Recommended
Bolt length for top of door
Recommended
Bolt length for bottom of door
Upto 2200mm
190mm
190mm
Upto 2450mm
450mm
190mm
Over 2450mm
600mm
190mm
BOTTOM
FLUSH
BOLT
Routing detail for bolt keep sockets
Top Flush Bolt into Head
Bottom Flush Bolt into Sill
Fixing screw centres
40
Ø12
PLATE
Ø12
10
4
10
12.5
12.5
SILL
REBATE
40
10
40
30
25
12
65
40mm fixing screw centres - Use fixing plate as drilling template
SILL
18
12.5
Section through door showing
flush bolt rebate detail
(All dimensions in mm)
12. 12
Inward Opening Flush Bolt
For top hung exterior folding doors. For use in conjunction with standard inward opening fitting
instructions. Follow routing instructions for the bolt keep and flush bolt length to be fitted, fit both with
the screws supplied. Suitable pilot holes for screws are recommended.
Routing detail for
600mm Top Flush Bolt
HEAD BOARD
12
LINTEL
20
Routing detail for
190mm Bottom
Flush Bolt
580
430
170
Note: Routing
detail is the same for
both locking and nonlocking flush bolts.
FASCIA
Routing detail for
450mm Top Flush Bolt
Routing detail for
190mm Top Flush Bolt
80
600
450
190
PLATE
12
29
4
40
22
17
22
40
22
17
INSIDE
4
190
Enlarged detail showing the
sectional routing dimensions
for all 3 top bolt sizes
OUTSIDE
170
TOP FLUSH
BOLT
Enlarged detail
showing the
sectional routing
dimensions for
the bottom bolt
12
Door height
Recommended
Bolt length for top of door
Recommended
Bolt length for bottom of door
Upto 2200mm
190mm
190mm
Upto 2450mm
450mm
190mm
Over 2450mm
600mm
190mm
BOTTOM FLUSH
BOLT
(Locking bolt shown)
Routing detail for top bolt keep socket
Ø12
65
10
12.5 max 7.5
12
SILL
REBATE
11
12.5 max
4
40
SILL
10
40
Plate fixing screw centres
40mm fixing screw centres - Use fixing plate as drilling template
Section through door showing
flush bolt rebate detail
(All dimensions in mm)
Coastal Joinery Hardware, Global House, Bojea Industrial Estate, Trethowel, St Austell, Cornwall, PL25 5RJ.
Tel: 01726 871726 Fax: 01726 871731 Email: sales@coastal-group.com
Part No: 220899
Issue 4 - January 2013
13. ENQUIRY FORM FOR BI-FOLD DOORS
Please enter your address here:
Your Details/FAO
Address
Telephone:
Fax:
PROJECT TITLE:
Email:
LOCATION:
SPECIFICATION SHEET
System Capacity:
1. Opening Size:
BI-FOLD DOORS
Maximum Leaf Height: 3300mm
Maximum Leaf Width: 1000mm
Maximum Leaf Weight: 100kg
Leaf Thickness: 35mm-68mm
mm
Height:
2. Door Configuration:
Number of leaves sliding (viewed from the outside)
Width:
mm
RH
LH
3. Outward Opening:
Due to weathering, outward opening Is
highly recomended.
Yes
No
4. Locking
None
Espagnolette
Sash lock
5. Finish
Satin Stainless Steel
PVD Brass
Polished Stainless Steel
6. System
CoFold
CoFold Ultra (High Security)
7. Gear Types
Choice only applies to CoFold system &
not the CoFold Ultra.
Mortice
Non Mortice
8. Weatherseal Required:
None
Brown
White
PRE-TENSION
Coastal Group | T 01726 871726 | F 01726 871731
Email sales@coastal-group.com | Visit www.coastal-group.com