SHIELD INSTALLATION.ppt

SHIELD INSTALLATION.ppt
Commissioning ► Keypad Configuration ► SHIELD Software Configuration ► Operation ►
SHIELD Intelligent 8 Loop FACP Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► • Listed to LPCB • 8 x Loops (242) capacity (1936) addressable points • 140 programmable LED zones • Maximum 10 Loops Standalone, Modular constructed for future expansion • 40 x15 lines LCD Display. • Up to 999 programmable zones and 140 zone indication • Auto Programming Day and Night Mode • Enable and Disable function • PAS and Acknowledge Function • Dirty Detector Reporting • Duplicate Address Checking and Device Mismatch • Walk Test Function with optional silent mode SHIELD
SHIELD Intelligent 8 Loop FACP Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► • Start and Stop Function • Can edit device detailed and programmed • Day/Night delay time disable • Programmable form PC or Panel • History record- almost 2000 event capacity in non-volatile memory • Fully simulation of Cause and Effect • Advanced user friendly programming software including ‘Fuzzy Logic’. • Networked with all SHIELD Intelligent Fire panels up to 64 Nodes, • Optional RS 485 mimic and repeater output up 64 • Optional RS 232-USB CRT interface for P-CGS graphic • Built in Fire Alarm, FPE, Fault , Alarm Router output and Feedback signal • Panel Printer included • Built in Battery charger. continuation SHIELD
SHIELD Optional Cards Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► LSHIELD Loop Card DB-A8M Download Card NB-A8M Network Card Class A RB-A8M Repeater Card FIB232 NPORT CI-500R Interposing Relay SHIELD
Commissioning Equipment Required Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Appropriate installers handbook (SHIELD Training Manual) Copy of commissioning checklist A laptop installed with latest version software Programming tools SHIELD
Commissioning Equipment Required Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Correct use of a checklist will ensure a standard commissioning procedure is carried out in every instance and no aspects are overlooked. SHIELD
Programming Tools Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► D-APP Hand Held Programmer DB-A8M Programming Card SHIELD
Structures Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD
FASCIA Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 2 x 70 Zone Indication LED indicator Control Buttons SHIELD
Basic Wiring Diagram Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- LOOP 01 0+ 0- I+ I- OUTPUT + - F2 F1 A B NO COM TO FPE OUTPUT TO + - SOUNDER ALARM + - ROUTING FEED BACK REPEATER FAULT OUTPUT NC XS1 XS8 XS2 XS3 XS4 XS5 XS11 XS10 XS9 XS6 XS7 XS14 XS13 XS12 COM BOARD MAIN BOARD LOOP BOARD LOOP BOARD LOOP BOARD LOOP BOARD LOOP BOARD 2A AC220V XS15 +5V GND TO MAINBOARD TO MAINBOARD +5V GND XS1 IO ZONE TO PRINT XS6 XS3 F7.820.1238V2 F7.820.1238V2 RP1 + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL ZS2 + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL F7.820.1312V2 XP1 + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL ZS2 + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL + + HL HL F7.820.1312V2 XS5 PRINTER TX RX 24V GND GND 5V 24V GND 5V GND 24V TX RX +5V GND 27V GND BAT+ BAT- L N V- V+ DC Output 27V 11.7A AC Input AC Input + + - - +V AJD F7.820.1311V2 BT1 90V/260/12V Fuse MAIN CONTROL BOARD INDICATOR BOARD MAIN POWER BOARD POWER SWITCH AC FILTER AC/DC POWER CONVERTER ZONE INDICATOR BOARD SHIELD
Basic Mother Board Slot Positioning Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► XS1 XS8 XS2 XS3 XS4 XS5 XS11 XS10 XS9 XS6 XS7 XS14 XS13 XS12 COM BOARD MAIN BOARD LOOP BOARD LOOP BOARD LOOP BOARD LOOP BOARD LOOP BOARD XS15 +5V GND TO MAINBOARD F7.820.1238V2 24V GND 5V GND 24V TX RX LOOP 01 O+ O- I+ I- LOOP 02 O+ O- I+ I- LOOP 03 O+ O- I+ I- LOOP 04 O+ O- I+ I- LOOP 05 O+ O- I+ I- LOOP 06 O+ O- I+ I- LOOP 07 O+ O- I+ I- LOOP 08 O+ O- I+ I- LOOP 09 O+ O- I+ I- LOOP 10 O+ O- I+ I- OUTPUT TO SOUNDER F2 F1 A B OUTPUT TO FPE ALARM ROUTING FEED BACK REPEATER FAULT OUTPUT NO COM NC XT1 XT2 XT3 XT4 XT5 XT6 XT7 XT8 XT9 XT10 XT11 XT12 XT13 XT19 XT14 XT18 + _ Fitted 470 ohms + _ + _ FPE with fitted diode 4.7Kohms EOL + + FPE FPE Sounder with built-in diode Output Device with fitted diode + + O/P Sounder with built-in diode Output Device with fitted diode + + O/P A B Output to Repeater or Mimic Panel O+ O- I+ I- Loop Out Loop In LOOP 01 O+ O- I+ I- A1 LOOP 10 B1 B2 A2 Network Terminal - Class A Out to next panel A2 Out to next panel B2 In from next panel B1 In from next panel A1 Out to first device In from last device XT1 XT10 O+ O- I+ I- A LOOP 10 B Network Terminal - Class B Out to next panel A Out to next panel B XT10 No connection 4.7Kohms EOL 4.7Kohms EOL 4.7Kohms EOL Card Configuration 10 Loops + Repeater 10 Loops + Communication 8 Loops + Communication + Repeater 8 Loops + Communication+ Network 8 Loops + Network + Repeater 6 Loops + Communication + Network + Repeater Note: •Com Board (XS8-XS1) – Used only for Repeater/ Mimic Card RB-A8M or Communication Card DB-A8M (USB and serial connection) •Communication Card DB-A8M can be placed in any Loop Board using only serial port connection, USB is not accessible •Network card should be placed to Loop Board 5 (XS10-XS3) and wired in loop 10 terminal SHIELD
Card Configuration Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD 0 5 2 3 4 1 8 7 6 9 XS1 XS8 XS2 XS9 XS3 XS10 XS4 XS11 XS5 XS12 XS6 XS13 XS7 XS17 A1 LP-A8M-Dual Loop Card Loop 2-Loop card - Wired on Loop 02 terminal Loop 1-Loop card - Wired on Loop 01 terminal HL2 LED HL1 LED 0 5 2 3 4 1 8 7 6 9 A1 HL2 LED HL1 LED Main Card 0 5 2 3 4 1 8 7 6 9 HL1 HL2 A1 DB-A8M- Communication Card Loop 11 - CRT Card 01 0 5 2 3 4 1 8 7 6 9 A1 HL2 LED HL1 LED 0 5 2 3 4 1 8 7 6 9 A1 HL2 LED HL1 LED 0 5 2 3 4 1 8 7 6 9 A1 HL2 LED HL1 LED Loop 4-Loop card - Wired on Loop 04 terminal Loop 3-Loop card - Wired on Loop 03 terminal Loop 6-Loop card - Wired on Loop 06 terminal Loop 5-Loop card - Wired on Loop 05 terminal Loop 8-Loop card - Wired on Loop 08 terminal Loop 7-Loop card - Wired on Loop 07 terminal LP-A8M-Dual Loop Card LP-A8M-Dual Loop Card LP-A8M-Dual Loop Card Loop 9-Net Unit - Wired on Loop 10 terminal NB-A8MA - Network Card Sample… 8 Loops + Network + Communication card 8 Loops + Network + Repeater
Basic Card Addressing and Designation Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Setting the card address Numbering sequence, lower card is the recommended lowest numerical setting. Set dials on the additional board in ascending order. Each card must be set at least one higher digit than the lower card. CARD SUM: 03 LOOP SUM: 04 SUM:0012 ******************************** LOOP 1: Loop Card, Devices Sum: 003 LOOP 2: Loop Card, Devices Sum: 003 LOOP 3: Loop Card, Devices Sum: 003 LOOP 4: Loop Card, Devices Sum: 003 LOOP 5: Net Card-01, Net Sum: 02 LOOP 6: CRT CARD -01 Press F1 to print LOOP DEVICES info SHIELD
Panel And Card Addressing Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE SET-UP 2 ZONE SET-UP 3. COMMUNICATIONE SET UP 4. DAY/NIGTH TIME SETUP 5. MODIFY PASSWORD SETUP 6. C&E EQUATION SETUP 7. DEVICE TYPE SETUP FAR: OK FPE: OK OTS: OK 13:01:07 *COMMUNICATION SETUP* ******************************** 1. MONITOR INTERFACE 2. NETWORK INTERFACE FAR: OK FPE: OK OTS: OK 13:01:08 1. Monitor interface (for DB-A8M card) Please input loop number: (1:10) Please input panel address: (1-32) 2 Network Interface (for NB-A8M card) Please Input loop number: (1-10) Please Input panel address (1-64) Enter: Received Command : Enable/Disable Send Command : Enable/Disable Received Information : Enable/Disable Send Information : Enable/Disable Note: The address of the panel is saved in the card SHIELD
Basic loop Terminal Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► O+ O- I+ I- Loop Out Loop In LOOP 01 O+ O- I+ I- A1 LOOP 10 B1 A2 B2 Network Terminal - Class A out to next panel A2 out to next panel B2 in from next panel B1 in from next panel A1 Loop Wiring out to first device in from last device XT1 XT10 •Loop Address: 242 •Output Voltage:21-27Vdc •Output Current: 300mA •Wiring Topology: Class A or B •Recommended Cable length: 1200 meters •Recommended Cable: GST Fire Cable •Loop protection: Optional loop isolator (C-9503/4) Connect the loop within the panel as follows: Loop OUT + to Loop IN+/ Loop OUT- to Loop IN- . SHIELD
Basic Output / Input Terminal Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Output Condition Device Number Alarm (Default) Disable CE Mode Delay Time Program Stop – via Silence Button Alarm Routing Routing A 00000083 Immediate Yes No Yes No Output to Sounder Sounder A 00000082 Immediate Yes Yes Yes Yes Output to FPE FPE A 00000081 Immediate Yes Yes No No Note: For output dry contact use CI-500R (output capacity 5A/220VAC or 24VDC @26mA Alarm Current) SHIELD
Basic Auto-Learn/Registration Procedures Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Turn on the panel and perform an auto learn/registration as follows: 1. The control panel is set in COMMISIONING MODE by default, once it is powered ON, the system immediately after the start-up will automatically initialize the REGISTRATION process. 2. If the system set to MONITORING MODE change the setting by: (System Setup→ 3 Working State Set-up→ select 1 Commissioning State) 3. For manual registration (System Setup→ 4 Commissioning → select 1 Device Learn) X FIRE CONTROL PANEL SHIELD Wed 13 Jan 2012 Panel Healthy FAR: OK FPE: OK OTS: OK 13:14:15 *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *WORKING STATE SETUP* ******************************** 1.COMISSION 2. MONITOR FAR: OK FPE: OK OTS: OK 13:01:06 SHIELD
Basic Auto-Learn/Registration Procedures Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► To check the registered devices 1. Press “User Setup”, (Default password) then press Enter 2. Press “Browse Devices” 3. Select the loop number using UP/Down arrow and then press Enter *USER SET-UP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SET-UP 4. DELAY MODE SET-UP 5. ACKNOWLEDGE TIMER 6. TEST SET-UP 7. START SET-UP 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:14:15 CARD SUM: 03 LOOP SUM: 04 SUM:0012 ******************************** LOOP 1: Loop Card, Devices Sum: 003 LOOP 2: Loop Card, Devices Sum: 003 LOOP 3: Loop Card, Devices Sum: 003 LOOP 4: Loop Card, Devices Sum: 003 LOOP 5: Net Card-01, Net Sum: 02 LOOP 6: CRT CARD -01 →F1 to print LOOP DEVICES info →F2 –Found devices F3- Missed devices FAR: OK FPE: OK OTS: OK 13:14:15 Loop01: Loop Card, Devices SUM:003 ******************************** D001 Group 001 Loop 1 Lift Mechanical Room D002 Zone-001 Loop 1 Optical Smoke Manager Room D003 Zone-001 Loop 1 Optical Smoke Secretary Room D004 Zone-001 Loop 1 Heat Detector Pantry FAR: OK FPE: OK OTS: OK 13:14:15 SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD
Basic Software Configuration Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 1. Control Panel Detailed 2. Number of Loop 3. Zone Detailed ( LED and PAS) 4. Device Detailed per Loop (Naming of Repeater/Mimic) 5. Equation (Cause & Effect) 6. Saving Data 7. Download / Upload SHIELD
1. Control Panel Detailed Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Adding Control Panel 1. Click the “FACP Net” icon 2. Right-click “FACP” and select “Add FACP” •FACP Type: Select the panel part number •FACP Address: Address of the panel •FACP Name: File name reference •Net: Click if the panels are network SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 2. Number of Loop Adding the loop 1.Click the “FACP Net” icon 2.Right-click “Panel that will add loop” and select “Add Loop” 3.Click “OK” SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 3. Zone Configuration Adding a zone 1.Click the “FACP Zone” icon 2.Right-click “Panel that will add zone” and select “Add Zone” 3.Or Click the “New” icon Note: Max number of zone is 999 Zone ID : Zone number Zone Mode: 0-Off: Panel display Fire immediately- No Pre-alarm feature 1-Type A: Enable Pre-alarm/ The system shall response to a second alarm from any device in the same zone as the system alarm (Type A) 2-Type B: Enable Pre-alarm/ The system shall response to a second alarm from any device in the same or other zone as the system alarm (Type B) Zone Sounder Mode 0-Sound By Zone Fire: Alarm the sounder automatically if the fire is on the same zone Ex: fire in zone 1, all the sounders in zone 1 will alarm 1-On E&C: Activation of Sounder through Equation Zone Resound Mode 0-No Resound: Sounder will not alarm if new fire from the other zone after being silenced 1-Resound by New Fire: Sounder will alarm if new fire from other zone after being silenced Zone LED: 1-140 LED ForeColor: Font Color BackColor: Text Highlight Color Description: Zone name (note: 40 Max character) Example: Zone example 4.To save click the “Save” icon SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 4. Device Detailed Device Configuration per Loop 1.Click the “FACP Net” icon 2.Click “Panel to be programmed” 3.Click the “Loop 1” Address: 1-242 Loop Number: Loop Number Zone: Zone assignment Device Type: Selection of device type. Properties: For output- 0-on/off ; 1-continoues Location: Device location information Note: character 40 max Registered: Once the data is uploaded from the panel, it will indicate TRUE if the particular device is being found or registered in the panel otherwise it will indicate False. 4. Click Save icon to save To configure the USER DEFINE •Click the “Panel that will configure” •Click the “Device Type -icons •The Device Type window will pop-up •Select the required condition and type new Device Type name SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 5. Equation ( Cause and Effect ) Configuring the Equation 1. Click the “FACP Net” icon 2. Click “Panel to be programmed” 3. Click the “Equation” 4. To save the equation click “Save New” 5. To modify the equation click “Save Modify” 6. To save the entire equation click “Save” Condition: INPUT DEVICES- 8 digits Effect: OUTPUT DEVICES – 10 digits Logic: AND Logic (x), OR Logic (+) Fuzzy Logic: Asterisk (* value 1-9) Delay Time Ratio: 1:10 seconds SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 5. Equation ( Cause and Effect ) 999 242 99 = 999 242 99 99 Zone Address Device Type Zone Address Device Type Delay Time Condition 001 020 03 meaning Address 20 Optical smoke in Zone 1 (By Point) 001 *** 03 meaning At least 1(any address) Optical smoke in Zone 1 (By Zone) *** *** 02 meaning At least 1(any address) Heat det. in the entire area (Global) Effect: XXX XXX 13 03 means sounder global alarm after 30 seconds (Global) Sample: 001 *** 11 + 001 *** 03 + 001 *** 02 = 001*** 13 00, *** *** 13 06 SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► 6. Saving and Restoring Data Click the “Database” icon The Database Operation window will pop out Click “Backup Database” to save the data. Save the data to the required location Click “Restore Database” to retrieve the data. Locate the data save SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Basic Software Configuration 7. Upload and Download Data Terminology: Download: Data transferring from the PC to the Control Panel Upload : Data transferring from the Control Panel to the PC Warning!! The data must be downloaded/uploaded by setting such as zone, loop, etc. Do not generally download/upload the data. 3 important things to note: 1. Registration of RS232 download card (Hardware) Identify the loop number of the DB-A8M card by pressing the “User Set-up” Select or press number 1 Browse Devices Press “System Setup” (No password) Press “Enter” Press “1 Programming” and then “3 Communication Set-up” Press “1 Monitor Interface” Please input loop number: (1:10) Please input panel address: (1-32) 2. Set Serial Port number (USB Connection-My computer-Properties-Hardware-Device Manger-Port) 3. Matched the address of the control panel “Local Address from the SHIELDDef software “FACP Address”. To view the control panels address: (Press “System Setup” 1 Programming3 Communication Set-up monitor or network interface) Note: •Com Board (XS8-XS1) – Used only for Repeater/ Mimic Card RB-A8M or Communication Card DB-A8M (USB and serial connection) •Communication Card DB-A8M can be placed in any Loop Board using only serial port connection, USB is not accessible SHIELD
Basic System Operation System Menu Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD
Basic Keypad Configuration 1. Zone Setup 2. Device Type Setup 3. Point Setup 4. C&E Set-up Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD
Zone Setup *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE SET-UP 2 ZONE SET-UP 3. COMMUNICATIONE SET UP 4. DAY/NIGTH TIME SETUP 5. MODIFY PASSWORD SETUP 6. C&E EQUATION SETUP 7. DEVICE TYPE SETUP FAR: OK FPE: OK OTS: OK 13:01:07 *ZONE SETUP* ZONE (1-999) : 001 ******************************** DEPENDENCY TYPE (0-2) : 0-OFF SOUNDER MODE (0-1) : 1-ON C&E RESOUND MODE (0-1) : 1- Resound by New Fire ZONE LED (1-140) : 001 TEXT (40 Byte) : GROUND FLOOR FAR: OK FPE: OK OTS: OK 13:01:08 Dependency Mode: 0-Off: Panel display Fire immediately- No Pre-alarm feature 1-Type A: Enable Pre-alarm/ The system shall response to a second alarm from any device in the same zone as the system alarm 2-Type B: Enable Pre-alarm/ The system shall response to a second alarm from any device in the same or other zone as the system alarm Zone Sounder Mode 0-Sound By Zone Fire: Alarm the sounder automatically if the fire is on the same zone Ex: fire in zone 1, all the sounders in zone 1 will alarm 1-On E&C: Activation of Sounder through Equation Zone Resound Mode 0-No Resound: Sounder will not alarm if new fire from the other zone after being silenced 1-Resound by New Fire: Sounder will alarm if new fire from other zone after being silenced Zone LED: 1-140 LED TEXT: Up to 40 characters Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Device Type Setup *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE SET-UP 2 ZONE SET-UP 3. COMMUNICATIONE SET UP 4. DAY/NIGTH TIME SETUP 5. MODIFY PASSWORD SETUP 6. C&E EQUATION SETUP 7. DEVICE TYPE SETUP FAR: OK FPE: OK OTS: OK 13:01:07 *DEVICE TYPE LIST* 00: Undefine 01: MultiSensor 02: Heat Detector 03: Optical Smoke 04: User Define 05: Gas Detector 06: Beam Detector 07: Flame detector 08: Conventional P 09: User Define 10: Flow Switch 11: MCP (BG) 12: Sounder Strobe 13: Sounder 14: Flasher 15: LIFT !Press key [F2] to modify device type FAR: OK FPE: OK OTS: OK 13:01:07 Device number Condition 1-11 FIRE 12-30 ACTION 31-40 FAULT 41-50 SUPERVISORY 51-65 ACTION 66-99 PANEL SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Device Setup *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE SET-UP 2 ZONE SET-UP 3. COMMUNICATIONE SET UP 4. DAY/NIGTH TIME SETUP 5. MODIFY PASSWORD SETUP 6. C&E EQUATION SETUP 7. DEVICE TYPE SETUP FAR: OK FPE: OK OTS: OK 13:01:07 *DEVICE SETUP* Loop: 01 Address(1-242) : 001 ******************************** ZONE (I-999) : 001 DEVICE TYPE: 03- Optical Smoke ATTRIBUTE (1-6) : 6 TEXT (40 Byte) : MANAGER ROOM FAR: OK FPE: OK OTS: OK 13:01:08 Zone: Zone assignment Device Type: Selection of device type. Attribute: Detector sensitivity/For output signal - 0-on/off ; 1-continoues Location: Device location information , max 40 characters SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Equation Setup *PROGRAMMING* ******************************** 1.DEVICE SET-UP 2 ZONE SET-UP 3. COMMUNICATIONE SET UP 4. DAY/NIGTH TIME SETUP 5. MODIFY PASSWORD SETUP 6. C&E EQUATION SETUP 7. DEVICE TYPE SETUP FAR: OK FPE: OK OTS: OK 13:01:07 CREATE C&E ******************************** C&E Quantity:001 N0.002 001***02+001***03= 001***1300 001***1200 FAR: OK FPE: OK OTS: OK 13:01:08 *C&E EQUATION SETUP* ******************************** 1.CREATE 2 MODIFY 3. DELETE – (DELETE ONE BY ONE) 4. INITIALIZATION - (DELETE ALL ) FAR: OK FPE: OK OTS: OK 13:01:07 NOTE: Condition: INPUT DEVICES- 8 digits Effect: OUTPUT DEVICES – 10 digits Delay Time Ratio: 1:10 seconds Number Arrangement: 999 242 99 = 999 242 99 99 Zone Address Device Type Zone Address Device Type Delay Time SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Equation Setup Types of logic Condition: 001 020 03 meaning Address 20 Optical smoke in Zone 1 (By Point) 001 *** 03 meaning At least 1(any address) Optical smoke in Zone 1 (By Zone) *** *** 02 meaning At least 1(any address) Heat det. in the entire area (Global) Effect: XXX XXX 13 03 means sounder global alarm after 30 seconds (Global) Sample: 001 *** 11 + 001 *** 03 + 001 *** 02 = 001*** 13 00, *** *** 13 06 Note: Logic: AND Logic (x), OR Logic (+) Fuzzy Logic: Asterisk (* value 1-9) SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Commissioning Menu 1. Device Learn 2. Duplicate Address Check 3. Modify Address 4. Modify Device Sensitivity 5. Commission Analog 6. Commission Digital 7. System Initialization SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Device Learn *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 REGISTERING ACTIVE EQUIPMENT PLEASE WAIT……… FAR: OK FPE: OK OTS: OK 13:01:07 Note: The panel must be set to “Commissioning Mode” SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Duplicate Check *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 DUPLICATED ADDRESS CHECKING Please wait…… Press [Cancel] to Exit! FAR: OK FPE: OK OTS: OK 13:01:07 Note! to access into Duplicated Check: 1.The panel must be set to “Commissioning Mode” 2. The system must initialize to “Digital Mode” To find out the duplicated address: User Setup→1 Browse→4 Browse Duplicated Address Enter the loop which have duplicated addresses to view the addresses DUPLICATED ADDRESS CHECKE OK Duplicated Address Sum: 001 FAR: OK FPE: OK OTS: OK 13:01:07 CARD SUM: 03 LOOP SUM: 04 SUM:0012 ******************************** LOOP 1: Loop Card, Dupli. Add. Sum : 000 LOOP 2: Loop Card, Dupli. Add. Sum : 001 LOOP 3: Loop Card, Dupli. Add. Sum : 000 LOOP 4: Loop Card, Dupli. Add. Sum : 000 LOOP 5: Net Card-01, Net Sum: 02 LOOP 6: CRT CARD -01 →F1 to print LOOP DEVICES info →F2 –Found devices F3- Missed devices FAR: OK FPE: OK OTS: OK 13:14:15 SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Modify Address *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 Note: The panel must be set to “Commissioning Mode” To change the address. 1.Enter the loop number and address you wish to change. 2.Type the new address into “NEW CODE” then Enter. *MODIFY ADDRESS* Loop: 01 Address(1-242) : 001 ******************************** USER CODE : 00100115 SERIAL NO.: 0000BB40 NEW CODE: 002 FAR: OK FPE: OK OTS: OK 13:01:08 SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Modify Device Sensitivity *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 Note: The panel must be set to “Commissioning Mode” To change the detector sensitivity. 1.Enter the loop number and address you wish to change. 2.Type the sensitivity into “NEW SENSITIVITY” then Enter. 3 LEVELS OF SENSITIVITY LEVEL 1: HIGHEST SENSITIVITY LEVEL 2: STANDARD SENSITIVITY LEVEL 3: LOWEST SENSITIVITY LEVEL 4: FOR FUTURE USE LEVEL 5: FOR FUTURE USE LEVEL 6: FOR FUTURE USE *MODIFY DEVICE SENSITIVITY* Loop: 01 Address(1-242) : 001 ******************************** USER CODE : 00100115 DEVICE TYPE: MULTISENSOR SENSITIVITY: 1- SENSITIVITY 1 NEW SENSITIVITY: 0 FAR: OK FPE: OK OTS: OK 13:01:08 SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Commission in Analog/Digital Mode *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 Note: The panel must be set to “Commissioning Mode” Commission to Analog mode: Normal Status: Range 450 to 650 Alarm Status: Range 900 to 1200 Fault Status: Range 1 to 120 Commission to Digital Mode: For future use *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Initialization Mode *SYSTEM SETUP* ******************************** 1.PROGRAMMING 2. LOCAL OUTPUT SET-UP 3. WORKING STATE SET UP 4. COMMISSIONING FAR: OK FPE: OK OTS: OK 13:01:06 *PROGRAMMING* ******************************** 1.DEVICE LEARN 2 DUPLICATED ADDRESS CHECK 3. MODIFY ADDRESS 4. MODIFY DEVICE SENSITIVITY 5. COMMISSION IN ANALOG MODE 6. COMMISSION IN DIGITAL MODE 7. SYSTEM INITIALIZATION FAR: OK FPE: OK OTS: OK 13:01:07 Note: 1.The panel must be set to “Commissioning Mode” 2. Required Initialization password:_______________ Detector: Indicate the current mode Digital mode : to have access in the following 1. Duplicated Address Check 2. Modify Address 3. Modify Device Sensitivity Analog mode: Default mode and must be used as the working mode Initialize System: To reset the main control card – this will delete the configuration of Zone LED, Equation and Device type list. Warning!! Make sure you have the back up data base Hide Sounder Plant Item – if you wish not to shown the active sounders Detector: Analog Mode Press [1] Initialize detector in digital mode Press [2] Initialize detector in analog mode Press [3] To Initialize the system Press [4] To disable the battery resistance Press [5] To hide sounder plant item FAR: OK FPE: OK OTS: OK 13:01:07 SHIELD
Commissioning ► Software Configuration ► Basic System Operation 1. Browse 2. Delay Mode Setup 3. PAS – Positive Alarm Sequence 4. Test Setup 5. Start and Stop 6. Disable/Enable Keypad Configuration ► Operation ► SHIELD
Commissioning ► Software Configuration ► Browse *USER SETUP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SETUP 4. DELAY MODE 5. ACKNOWLEDGE TIMER 6. TEST SETUP 7. START/STOP DEVICE 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:01:06 *BROWSE* ******************************** 1.BROWSE DEVICES 2 BROWSE ZONES 3.BROWSE GROUPS 4.BROWSE DUPLICATED ADDRESS 5.BROWSE PANEL STATUS 6.BROWSE C&E EQUATION 7. HISTORY LOG FAR: OK FPE: OK OTS: OK 13:01:07 1 Browse Devices: View the number of devices per loop and detailed provided with each device 2 Browse Zones: View the total number of Input devices per zone 3 Browse Groups: View the total number of Output devices per group (Zone) 4 Browse Duplicated Address : View the repeated address in a loop 5 Browse Panel Status: View the panel configuration and version 6 Browse C&E Equation: View configured equation 7 History LOG: 1 Fire History 2 Common History 3 Initialization Keypad Configuration ► Operation ► SHIELD
Commissioning ► Software Configuration ► Delayed Mode Setup *USER SETUP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SETUP 4. DELAY MODE 5. ACKNOWLEDGE TIMER` 6. TEST SETUP 7. START/STOP DEVICE 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:01:06 *DELAY MODE SETUP* ******************************** 1.ENABLE 2 DISABLE FAR: OK FPE: OK OTS: OK 13:01:07 4 DELAY MODE SETUP Commission or Monitor Mode 1 Disable - No output delay 2 Enable - Enable the équations delay time Note: The Delay Mode LED will turn ON Setting required to enabling the delay outputs based on the configured C&E equation: •Enable the delay command form DELAY MODE SETUP •Configured the system “DAY TIME” form DAY/NIGTH SETUP •Configured the zone mode parameter into 1- on C&E from the ZONE SETUP Keypad Configuration ► Operation ► SHIELD
Commissioning ► Software Configuration ► PAS Setup *USER SETUP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SETUP 4. DELAY MODE 5. ACKNOWLEDGE TIMER 6. TEST SETUP 7. START/STOP DEVICE 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:01:06 *ACKNOWLEDGE TIMER* ******************************** 1.Please input the Pre-Alarm ACK time: Phase 1 (Default 30S) : [00] M - [30] S 2.Please input the Pre-Alarm Verify time: Phase 2 (Default 2M) : [02] M - [00] S FAR: OK FPE: OK OTS: OK 13:01:07 Dependencies on more than one alarm signal – Type A & B (EN54 P2-7.12) Day Mode *Pre-alarm Window: programmable from 1 sec. to 30 min. A distinctive pre-alarm indication shall be displayed. *Alarm Verification window: programmable from 1 sec. to 30 min. The system shall response to a second alarm from any device in the same zone as the system alarm (Type A) The system shall response to a second alarm from any device in the same or different zone as the system alarm (Type B) Night Mode (Default setting) *Pre-alarm Window: preprogrammed 30 min. Auto-reset the Alarm in the Panel after 30 min (Type A) *Pre-alarm Window: preprogrammed 5 min. Auto-reset the Alarm in the Panel after 5 min (Type B) The system shall response to a second alarm from any device in the same zone as the system alarm (Type A) The system shall response to a second alarm from any device in the same or different zone as the system alarm (Type B) Keypad Configuration ► Operation ► SHIELD
Commissioning ► Software Configuration ► Test Setup *USER SETUP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SETUP 4. DELAY MODE 5. ACKNOWLEDGE TIMER 6. TEST SETUP 7. START/STOP DEVICE 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:01:06 *TEST SETUP* ******************************** 1.LED BUZZER TEST 2 LOCAL OUTPUT TEST 3. SETUP TEST ZONE 4. CANCEL TEST ZONE FAR: OK FPE: OK OTS: OK 13:01:07 TEST SETUP Commission or Monitor Mode 1 LED Buzzer Test – Test all the LED and Buzzer 2 Local Output Test – To test the 3 on board outputs 1 Output to Sounder Test (OTS) 2 Output to F.P.E. (FPE) 3 Alarm Routing Test (FAR) 3 Setup Test Zone Input test zone : (1-999) Input test mode : (0-1) 0-Without sounder 1-With sounder – Automatic Stop after 10 seconds 4 Cancel Test Zone 1 Cancel One Test Zone 2 Cancel All Test Zone Keypad Configuration ► Operation ► SHIELD
Commissioning ► Software Configuration ► Start/Stop Setup *USER SETUP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SETUP 4. DELAY MODE 5. ACKNOWLEDGE TIMER 6. TEST SETUP 7. START/STOP DEVICE 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:01:06 *START/STOP DEVICE* ******************************** 1.START DEVICE 2 STOP DEVICE FAR: OK FPE: OK OTS: OK 13:01:07 *START/STOP DEVICE* ******************************** 1.START DEVICE 2 STOP DEVICE START→ ZONE: 000 DEV: 000 TYPE: 00-Un-define FAR: OK FPE: OK OTS: OK 13:01:07 Keypad Configuration ► Operation ► Note: Input the device code Zone Device Address Device Type SHIELD
Commissioning ► Software Configuration ► Disable/Enable *USER SETUP* ******************************** 1.BROWSE 2. CLOCK 3. PRINTER SETUP 4. DELAY MODE 5. ACKNOWLEDGE TIMER 6. TEST SETUP 7. START/STOP DEVICE 8. DISABLE/ENABLE FAR: OK FPE: OK OTS: OK 13:01:06 *DISABLE/ENABLE* ******************************** 1.DIS/ENABLE DEVICE-BY CODE 2 DIS/ENABLE DEVICE –BY ADDRESS 3. DIS/ENABLE ZONE 4. DIS/ENABLE SOUNDER FAR: OK FPE: OK OTS: OK 13:01:07 DISABLE/ENABLE Commission or Monitor Mode 1 Dis/Enable Devices – By Code 1 Disable Device 2 Enable Device 2 Dis/Enable Device – By Address 1 Disable Device 2 Enable Device 3 Dis/Enable Zone 1 Disable Zone 2 Enable Zone 4 Disable/Enable Sounder 1 Disable Sounder 2 Enable Sounder Keypad Configuration ► Operation ► SHIELD
Commissioning ► Keypad Configuration ► Software Configuration ► Operation ► Question & Answer SHIELD

SHIELD INSTALLATION.ppt

Check these out next

SHIELD INSTALLATION.ppt

Recomendados

Más contenido relacionado

Similar a SHIELD INSTALLATION.ppt(20)

Último(20)

SHIELD INSTALLATION.ppt