The file contains all details of the Condenser and Cooling Tower systems or Thermal power plant. This is the part of the subject Power Plant Engineering in GTU in 7th semester.

1. Faculty Name: Prof. Ajaypalsinh G. Barad
Branch: Mechanical
College : S. P. C. E., Visnagar
Semester: 7th Semester
Name of Subject: Power Plant Engineering
1Ajaypalsinh Barad
Condensers
and
Cooling Towers

2. Outline
• Introduction
• Types of condensers
• Sources of air in condenser
• Effects of air leakage
• Methods of obtaining maximum vacuum in condenser
• Vacuum & condenser efficiency
• Mass of cooling water required
• Edward air pump
• Necessity of cooling ponds and cooling towers
• Condenser water cooling systems
• Types of cooling towers and cooling ponds
2Ajaypalsinh Barad

3. Introduction :
3Ajaypalsinh Barad
• Objective of a steam condenser:
– To create low back pressure for turbine exhaust
– To condense the exhaust steam from the turbine

4. Introduction :
4Ajaypalsinh Barad
Advantages :
• Increases work done per kg of steam
• Increases thermal efficiency of plant
• Condensed steam provides a source of good pure feed
water.
• High temperature condensate water reduces amount of
heat supplied per kg of steam
• Reduces corrosion of boiler tube

5. Introduction :
5Ajaypalsinh Barad
Elements of steam condensing plant :
• Condenser
• Supply of cooling water
• Condenser cooling water pump
• Air extraction pump
• Make up water pump
• Condensate extraction pump
• Boiler feed pump
• Hot well
• Cooling tower

6. Introduction :
6Ajaypalsinh Barad

7. Types of Condensers :
Two main types :
• Jet condenser
• Surface condenser
7Ajaypalsinh Barad

8. Jet Condenser :
• It is further classified on the basis of Direction of
flow of the condensate and Arrangement of the
tubing system.
Types:
• Low level jet condenser
– Parallel flow type
– Counter flow type
• High level jet condenser
• Ejector jet condenser
8Ajaypalsinh Barad

9. Low Level Parallel Flow Jet Condenser :
9Ajaypalsinh Barad

10. Low Level Counter Flow Jet Condenser :
10Ajaypalsinh Barad

11. High Level Jet Condenser :
11Ajaypalsinh Barad

12. Ejector Condenser :
12Ajaypalsinh Barad

13. Jet Condenser :
13Ajaypalsinh Barad
Advantages :
• Lower quantity of cooling water required
• Simple in design
• Require less floor space
• Lower capital and maintenance cost
• Due to direct contact heat transfer is more effective
Disadvantages :
• Condensate cannot be directly used as feed water
• Power consumption in pump is more
• Piping cost is high.

14. Surface Condenser :
14Ajaypalsinh Barad
• It is further classified as follows :
• According to number of cooling water passes
– Single pass
– Multi pass
• According to direction of condensate flow
– Down flow condenser
– Central flow condenser

15. Double Pass Surface Condenser :
15Ajaypalsinh Barad

16. Down Flow Surface Condenser :
16Ajaypalsinh Barad

17. Down Flow Surface Condenser :
17Ajaypalsinh Barad

18. Central Flow Surface Condenser :
18Ajaypalsinh Barad

19. Evaporative Condenser :
19Ajaypalsinh Barad

20. Evaporative Condenser :
20Ajaypalsinh Barad

21. Evaporative Condenser :
21Ajaypalsinh Barad
Advantages:
• Simple in design and low initial cost
• Low quantity cooling water required
• Small capacity cooling water pump
• Low operating cost.
Disadvantages:
• Vacuum maintained is less
• Due to less vacuum work done per kg of steam is less
• Not suitable for medium and large power plant

22. Surface Condenser :
22Ajaypalsinh Barad
Advantages:
• Due to high vacuum increases thermal efficiency and
output of plant
• Condensate can be reused as boiler feed water
• Auxiliary power requirement is less
• Less amount of air is carried to the boiler
• Any kind of feed water can be used
• Can develop high vacuum, so suitable for medium
and large power plants

23. Surface Condenser :
23Ajaypalsinh Barad
Disadvantages:
• Very bulky and requires more floor space
• High manufacturing, running and maintenance cost
• Requires large quantity of cooling water

24. Surface Condenser :
24Ajaypalsinh Barad
Requirement of good surface condenser:
• There should be uniform distribution of exhaust steam
throughout the heat transfer surface of the condenser
• There should not be any leakage of air into the
condenser
• There should not be any tube leakage
• The heat transfer surface in contact with cooling water
must be free from any deposit as scaling reduces the
efficiency of heat exchangers.

25. Comparison :
25Ajaypalsinh Barad
Jet Condenser Surface Condenser
Cooling water and steam
come in direct contact
Cooling water and steam
do not come in direct
contact
Maintenance cost is low Maintenance cost is high
More suitable for low
capacity plants
More suitable for high
capacity plants
Condensate is not used as
boiler feed water
Condensate is directly used
as boiler feed water

26. Comparison :
26Ajaypalsinh Barad
Jet Condenser Surface Condenser
Condensation of steam is
due to heat transfer by
mixing of steam with water
Condensation of steam is
due to heat transfer by
steam to water through
tubes
Economic and simple
condensing plant
Costly and complicated
condensing plant
More power consumption
in air pump
Less power consumption in
air pump

27. Sources of Air in Condenser :
• The boiler feed water contains dissolved air. From the
boiler it is carried off by steam and to the turbine and
finally to the condenser
• The air leaks through the joints, packing and glands
into the condenser where the pressure is below the
atmospheric pressure.
• Air dissolved with cooling water is carried in case of
jet condensers.
27Ajaypalsinh Barad

28. Effects of Air Leakage :
• Increases the back pressure on the turbine with the
effect that there is low thermal efficiency of the
plant
• Reduces the rate of condensation of steam because air
having poor thermal conductivity, reduces the
overall heat transfer from the steam air mixture.
• The presence of air in the condenser increases the
corrosive action.
28Ajaypalsinh Barad

29. Method of obtaining max vacuum :
• Air pump : extract the air and other non-condensable
gases from the condenser to maintain a desired
vacuum.
– Wet pump : removes a mixture of condensate and air
with other non-condensable gases.
– Dry pump : removes the air and other non-condensable
gases only.
29Ajaypalsinh Barad

30. Method of obtaining max vacuum :
• Steam Jet Air Ejector : remove air from condenser
when a wet pump is employed. It consist of
convergent – divergent nozzle and a diffuser.
30Ajaypalsinh Barad

31. Method of obtaining max vacuum :
• De-aerated feed water : the de-aeration is the
process of removal of non condensable gases from
feed water. It helps both in maintaining better vacuum
in the condenser and controlling corrosion of the steel
and piping of the steam power plant.
• Air tight joints : the air leaks through the joints,
packings and glands into the condenser. This can be
reduced by proper workmanship while making the
joints and these are maintained as such by proper
inspection from time to time.
31Ajaypalsinh Barad

32. Vacuum & Condenser Efficiency :
• The minimum absolute pressure at the steam inlet of
a condenser is the saturation pressure corresponding
to the temperature of the condensed steam. This
vacuum is called Ideal Vacuum. It is the maximum
vacuum that can be obtained in a condensing plant,
with no air present at that temperature.
• The actual pressure in the condenser is greater than
the ideal pressure by an amount equal to the pressure
of air present in the condenser.
• The ratio of the actual vacuum to the ideal vacuum is
known as Vacuum Efficiency.
32Ajaypalsinh Barad

33. Vacuum & Condenser Efficiency :
• If,
Ps = Saturation pressure of steam corresponding to the steam
temperature entering into condenser
Pc = Total pressure of air and steam in the condenser (Pa + Ps).
Pb = Atmospheric pressure.
• Ideal vacuum possible without air leakage = (Pb - Ps)
• Actual vacuum existing in condenser due to air
leakage
33Ajaypalsinh Barad

34. Vacuum & Condenser Efficiency :
• It is the ratio of actual rise in the temperature of
cooling water to the maximum possible rise in
temperature of cooling water.
34Ajaypalsinh Barad

35. Mass of Cooling Water Required :
35Ajaypalsinh Barad

36. Mass of Cooling Water Required :
36Ajaypalsinh Barad

37. Edward Air Pump :
37Ajaypalsinh Barad

38. Edward Air Pump :
38Ajaypalsinh Barad

39. Necessity of Cooling Ponds & Towers :
• To absorb the heat from steam.
• It is necessary to pre-cool the water coming out of
condenser before using again in a closed system. As
with increase in temperature pressure also increases.
39Ajaypalsinh Barad

40. Condenser Water Cooling System :
• Cooling water systems used in practice according to
availability of water are :
– Open Cooling System (Once Through System)
– Closed Cooling System
– Mixed Cooling System
40Ajaypalsinh Barad

41. Open Cooling System (Once Through System) :
41Ajaypalsinh Barad

42. Closed Cooling System :
42Ajaypalsinh Barad

43. Mixed Cooling System :
43Ajaypalsinh Barad

44. Types of Cooling Towers & Ponds :
• Cooling towers cool the warm water discharged from
the condenser and feed the cooled water back to the
condenser.
• Types of cooling towers :
– Natural draught cooling towers
– Mechanical cooling towers
• Forced draught cooling towers
• Induced draught cooling towers
44Ajaypalsinh Barad

45. Natural Draught Cooling Towers :
45Ajaypalsinh Barad

46. Natural Draught Cooling Towers :
46Ajaypalsinh Barad

47. Natural Draught Cooling Towers :
Advantages :
• Its operating and maintenance costs are less since no
fans are needed.
• It creates its own draft assuring efficient operation
even when there is no wind.
• Longer life.
Disadvantages :
• High capital cost
• Performance varies with the seasonal changes
47Ajaypalsinh Barad

48. Forced Draught Cooling Tower :
48Ajaypalsinh Barad

49. Forced Draught Cooling Tower :
49Ajaypalsinh Barad

50. Forced Draught Cooling Tower :
Advantages:
• More efficient
• Problems of blade erosion are avoided
• Fan is located at ground so more safe
• Vibration and noise are less as mechanical equipments are
set on a solid foundation.
Disadvantages :
• Possibility of recirculation of hot humid exhaust air
coming out from the top of the tower
• Fan size is limited to 4 meters
• Possibility of ice formation on fan blades in cold weather
50Ajaypalsinh Barad

51. Induced Draught Cooling Tower (Counter) :
51Ajaypalsinh Barad

52. Induced Draught Cooling Tower (Counter) :
52Ajaypalsinh Barad

53. Induced Draught Cooling Tower (Cross) :
53Ajaypalsinh Barad

54. Induced Draught Cooling Tower :
Advantages:
• Coldest water comes in contact with the driest air and
the warmest water comes in contact with the most air.
• The recirculation of hot humid air is not a major
problem.
• Larger fan size can be used.
• Lower first cost due to the reduced pump capacity
• Capable of cooling through a wide range.
54Ajaypalsinh Barad

55. Induced Draught Cooling Tower :
Disadvantages:
• Not economical up to the capacity of 15000 liters of
water per minute.
• Higher power motor is required to drive the fan
compared to forced draught.
• Maintenance cost is high.
• Fan bearings need to be cooled.
55Ajaypalsinh Barad

56. Cooling Ponds :
• The cooling pond is one of the simplest method of
cooling the condenser water. This method is less
efficient than cooling tower.
• Types of cooling ponds:
1. Natural and Directed flow cooling pond
2. Single deck and Double deck cooling pond
3. Open and Louvre fence cooling pond.
56Ajaypalsinh Barad

57. Cooling Ponds :
Natural flow cooling pond
57Ajaypalsinh Barad

58. Cooling Ponds :
Directed flow cooling pond
58Ajaypalsinh Barad

59. Cooling Ponds :
Single deck cooling pond
59Ajaypalsinh Barad

60. Cooling Ponds :
Double deck cooling pond
60Ajaypalsinh Barad

61. Cooling Ponds :
Single deck cooling pond
61Ajaypalsinh Barad

62. Cooling Ponds :
• Spray pond with Louvre fence
62Ajaypalsinh Barad

63. Cooling Ponds :
Advantages:
• Initial cost is less
• Simple in design and arrangement
Disadvantages:
• Requires large area for cooling.
63Ajaypalsinh Barad