1. SHAPER
• Shaper is Machine tool which produces
flat surfaces in horizontal, vertical or
inclined planes depending upon the
orientation of the cutting tool.
Features:
• Single point cutting tool is used for
machining. Tool is clamped in the tool
post mounted on the ram of the machine.
• The ram reciprocates to and fro, tool cuts
the material in the forward stroke, No
cutting during return stroke.
• Job is held rigidly in a vice.
MP II UNIT 3 SHAPER AND PLANER MECH
1
DEPT KSSEM 2013
2. • PRINCIPLE
• HORIZONTAL SHAPER – PARTS AND SKETCH
• SHAPER MECHANISMS
• OPERTIONS DONE ON SHAPER
• CLASSIFICATION OF SHAPER
• SPECIFICATIONS OF SHAPER
• MACHINING TIME CALCULATIONS
• COMPARISON BETWEEN SHAPER AND PLANER
MP II UNIT 3 SHAPER AND PLANER MECH
2
DEPT KSSEM 2013
3. MP II UNIT 3 SHAPER AND PLANER MECH
3
DEPT KSSEM 2013
4. Forward stroke is the cutting stroke. Return stroke the tool does not cut,
Double stroke= cutting stroke + return stroke
Stroke starts slightly before the work piece (a) and ends after the work piece (b)
Total stroke length = l+a+b
MP II UNIT 3 SHAPER AND PLANER MECH
4
DEPT KSSEM 2013
5. Operations done using a shaper
• Machining Horizontal Surfaces
• Machining Vertical Surfaces
• Machining Angular Surfaces
• Cutting Slots, Grooves & Key ways
• Machining irregular surfaces
• Machining Splines / Cutting Gears
MP II UNIT 3 SHAPER AND PLANER MECH
5
DEPT KSSEM 2013
6. MP II UNIT 3 SHAPER AND PLANER MECH
6
DEPT KSSEM 2013
7. MP II UNIT 3 SHAPER AND PLANER MECH
7
DEPT KSSEM 2013
8. Main parts of a shaping machine
1. BASE 5. CROSS RAIL
2. COLUMN 6. SADDLE
3. RAM 7. TOOL HEAD
4. TABLE 8. CLAPPER BOX
MP II UNIT 3 SHAPER AND PLANER MECH
8
DEPT KSSEM 2013
9. PARTS OF SHAPER
BASE made of cast iron. Provides
support for other parts of
machine.
COLUMN- box type casting
mounted vertically on top of
base.
• It has 2 guide ways. One
vertical guideway in the front
over which a cross slide moves
up and down.
• 2nd horizontal guide ways on
top over which ram reciprocate.
• The reciprocating mechanism is
housed inside the column
MP II UNIT 3 SHAPER AND PLANER MECH
9
DEPT KSSEM 2013
10. MP II UNIT 3 SHAPER AND PLANER MECH
10
DEPT KSSEM 2013
11. PARTS OF SHAPER TOOL HEAD fitted on the face of
CROSS RAIL IT IS MOUNTED ram. Holds the tool rigidly.
ON THE F RONT VERTICAL • Provide vertical and angular feeds
GUIDE WAYS. for the tool
• THE TABLE CAN BE • Tool head can be positioned at
LOWERED OR RAISED BY
any angle
ADJUSTING THE CROSS RAIL
TABLE- mounted on a saddle which
is located above the cross rail. Top
and and sides are accurately
machined and have T slots.
RAM- supports tool head on its front.
It reciprocates on accurately
machined guideways on top of
column
MP II UNIT 3 SHAPER AND PLANER MECH
11
DEPT KSSEM 2013
12. MP II UNIT 3 SHAPER AND PLANER MECH
12
DEPT KSSEM 2013
13. Classification of shapers
1 Position of ram travel
• Horizontal Shaper- Ram holding the cutting tool moves In
horizontal plane
• Vertical Shaper-The cutting tool moves in vertical plane
• Traveling head Shaper-Cutting tool reciprocates & moves cross
wise simultaneously
2 Acc. to Cutting Stroke action
a) Push Type Shaper- Standard Shaper.
• Metal is removed when the ram moves away from column
• Most common type used in practice
• Unless otherwise specified, the term shaper refers to Push type Shaper
b) Draw Type Shaper
• Metal is removed when the tool is drawn towards the column
• Allows heavier cuts to be made
• Less vibration during cutting
MP II UNIT 3 SHAPER AND PLANER MECH
13
DEPT KSSEM 2013
14. 3 Acc. to Driving Mechanism:
a) Crank type - Driving mechanism is by crank & gear
b) Geared type - Driven by Rack & Pinion mechanism
c) Hydraulic Shaper - Driven by oil pressure developed by a pump, which is run
by an electric motor
4 Acc. to the Table Design:
a) Standard shaper- Work Table can be moved
1.Vertically & 2. Horizontally
b) Universal Shaper- Table can be moved
1. Horizontally 2. Vertically 3. Swivelled & 4. Tilted
This is mostly used in Tool Rooms
Q HOW ARE SHAPERS CLASSIFIED? EXPLAIN BRIEFLY QUICK RETURN
MECHANISM USED IN SHAPER
MP II UNIT 3 SHAPER AND PLANER MECH
14
DEPT KSSEM 2013
15. SHAPER
MP II UNIT 3 SHAPER AND PLANER MECH
15
DEPT KSSEM 2013
16. Specifications of Shaping Machine
• Max.length of Stroke of Ram
• Type of Drive
• Power input
• Floor Space required
• Weight of the Machine
• Cutting to Return Stroke ratio
• Feed
MP II UNIT 3 SHAPER AND PLANER MECH
16
DEPT KSSEM 2013
17. SHAPER
MP II UNIT 3 SHAPER AND PLANER MECH
17
DEPT KSSEM 2013
18. MP II UNIT 3 SHAPER AND PLANER MECH
18
DEPT KSSEM 2013
19. MP II UNIT 3 SHAPER AND PLANER MECH
19
DEPT KSSEM 2013
20. MP II UNIT 3 SHAPER AND PLANER MECH
20
DEPT KSSEM 2013
21. MP II UNIT 3 SHAPER AND PLANER MECH
21
DEPT KSSEM 2013
22. SHAPING OPERATIONS
1
Machining of horizontal surface
The work surface is held securely on the table
and tool is fixed in the tool head with
minimum overhang, as shown in figure. The
table with fixed work piece is raised close to
the tool; the length and position of the stroke
are adjusted. The stroke length is about 20mm
longer than the work and stroke is adjusted
such that the tool starts about 10-15 mm
before work piece and continues about 10 mm
after the end of cut.
2
Work piece is mounted on the table and the
surface to be machined is set parallel to stroke
axis. A side cutting tool is fitted in the tool head
as shown in figure. The length of stroke is
adjusted as described in section 5.1. The cutting
feed is given by rotating the down feed screw
by hand (0.25 -0.50 mm)
MP II UNIT 3 SHAPER AND PLANER MECH
22
DEPT KSSEM 2013