The document provides an overview of the major systems that power a car, including the engine, fuel system, exhaust system, cooling system, drivetrain, suspension, electrical system, body, brakes, and heating/AC system. It describes the key components of each system, such as pistons, crankshaft, and valves in the engine. The summary explains how the engine uses a four-stroke process involving intake, compression, power, and exhaust strokes to combust fuel and turn the crankshaft. It also notes that modern cars use liquid cooling systems to regulate engine temperature.
2. Welcome to Car Basics! Here you will embark on great adventure i.e. learning all about the basics of the major system that power your car. Introduction
14. Your average car engine will have 4,6 or 8 pistons. You can think of piston as similar to âplungersâ moving up and down within their cylinders. On the top side of the piston is the combustion chamber, where fuel and air are mixed together before being ignited. On the other side of the piston is the crankcase, which is full of oil. Your air and fuel are kept separate from the oil by âO-Ringâ style rubber seals 1.Piston
15. 2. Crankshaft The crankshaft is connected to piston by a rod. As the piston moves up and down, the crankshaft rotates and converts the up and the down motion into rotatory motion. In other words, it helps turn the wheels.3. Valvetrain The valvetrain is made up of valves, rocker arms, pushrods, lifters and the cam shaft. The job of the valvetrain is to let the air and fuel in and out of the engine at the appropriate time. This is accomplished by synchronizing the cam shaft to the crankshaft with a belt or a chain.
16.
17. The average car today uses what is known as a â4-strokeâ or â4 cycleâ engine. What this means is that there are four separate events that happen in your engine as it runs: Intake stroke Compression stroke Power stroke Exhaust stroke How it all works
18. 1. Intake strokeAn intake valve is opened by the camshaft, and the piston moves down inside the cylinder creating a vacuum which sucks air and fuel into the combustion chamber.
19. 2. Compression stroke The intake valve closes as the piston moves up the cylinder. This creates a seal that allows the air and fuel to be compressed.
20. 3. Power stroke As the piston nears the top of the cylinder, the spark plug fires and ignites the compressed air and fuel. The force of ignition drives the piston back down into the cylinder again, turning the crankshaft..
21. 4. Exhaust strokeOnce the piston reaches the bottom of the cylinder again, the exhaust valves opens. Leftover air and gas are sent out to the exhaust system.
22. If any part of your fuel system breaks down, your engine will not. Therefore it is very important to keep your fuel system well-maintained and address any problem that come up soon as possible. Letâs look at the parts: Fuel tank Fuel pump Fuel filter Fuel injectors (newer cars) Carbonator (older cars) Your Carâs Fuel System
23.
24. 1. Fuel Tank Pretty self-explanatory! The fuel tank is where your carâs fuel is stored. Inside the tank is a sending unit which tells your gas gauge how much fuel is left in the tank.2. Fuel Pump On newer model cars, the fuel pump is usually installed inside the fuel tank. On older model cars, the fuel pump may be attached to the engine or on the frame rail between the tank and engine.3. Fuel Filter Fuel filters may be located before or after the fuel pump (and in some cars, there are two fuel filters â one before the pump, and one after). Intake valves tend to get clogged and fuel filters serve to clean this build up out of the gasoline.
25. 4. Fuel Injectors Fuel injection is used in the majority foreign and domestic cars produced after 1986. The fuel injector is a small, electric valve. The opening and closing of this valve is controlled by a computer.5. Carburetor On older model cars, a carburetor is used to help mix air and fuel. Itâs a very inefficient process , and carburetors are notorious for breaking down. This is why most manufactures switched to fuel injection.
26. Your exhaust system carries away the gasses created by engine combustion. The whole system consist of five components: Exhausted Manifold Oxygen Sensor Catalytic Converter Muffler Exhaust Pipe Your Carâs Exhaust System
27.
28. 1. Exhaust Manifold The exhaust manifold attaches to the cylinder head, taking the exhaust from each piston, and routing it through one pipe.2. Oxygen Sensor A component of fuel-injection system, the oxygen sensor monitors the level of oxygen present in the exhaust and makes adjustment to fuel input in order to maximize fuel economy. An oxygen sensor is usually mounted near the exhaust manifold.
29. 3.Catalytic Converter The catalytic converter acts somewhat like a filter in that itâs job is to convert harmful byproducts of the process into less harmful ones. Namely, carbon monoxide and hydrocarbons are converted to water vapor and carbon dioxide. Your catalytic converter should be located between your exhaust manifold and muffler.4.Muffler The muffler âmufflesâ the sound of your engineâs combustion and exhaust process. Sound is reduced by âbouncingâ the exhaust against internal baffles to reduce its energy.5.Exhaust Pipe Once your gas has turned to vapor within the exhaust system, it is carried out of your car through the exhaust pipe.
30.
31. As you can imagine, your carâs engine gets super hot while running. Normal operating temperature for the average fuel burning engine is around 2,000 degrees Fahrenheit, but temperatures may go up as high as 4,000 degrees F. during the combustion process. A cooling system is necessary for a couple of reason: To prevent temperature high enough to melt engine parts. To stabilize engine temperature at the most efficient level regardless of environmental conditions. While some heat is carried away by the exhaust system. Itâs not enough to protect the pistons and cylinders. Your Carâs Engine-Cooling System
32. Most automobiles use what is known as a âliquid-coolingâ system. In other words, a liquid âcoolantâ is circulated to absorb and carry away heat from the engine.This liquid is then sent o the radiator, where it is âre-cooledâ again and sent back out for another pass through the engine.Letâs look at the parts involved in the cooling system:1. Hoses2. Fan Belt3. Radiator4. Water Pump
33.
34. 1. HosesHoses are used to carry the liquid coolant.2. Fan Belt A Fan belt is used to drive the water pump, which circulates the coolant through the system.3. Radiator The radiator cools your coolant.4. Water Pump The water pump, which is driven by your engine via fan belt, is responsible for pushing the coolant to circulate
35. The drive train (also sometimes referred to as the âpower pointâ) serves two functions: Drive power from the engine to the drive wheel. Vary the amount of torque. We use the expression âdrive wheelâ to refer to the actual âdriven wheelsâ of a vehicle. For instance, an automobile with 2-wheel drive is designed to power 2 drive wheels (either the two front wheels or the back wheels), while the remaining wheels on the vehicle roll out but do not actually power the car forward. There are two sets of gears in the drive train: Transmission Differential Your carâs Drive Train
36. TransmissionThe transmission is used to adjust gear ratio. This is similar to (but more complex than) the gear-switching of a bicycle. Automotive transmission require multiple ratio gearboxes to maintain the same engine RPMâs at different speeds.Differential The differential is used to help the wheels turn at different speeds.Now , we can break the transmission down even further because there are 2 types of transmission you are probably familiar with:1.. Manual 2. Automatic.
37.
38. Manual Transmission Manual transmission usually have 4 or 5 speeds. Most use manual clutches, but there are a few models out there that actually use an electric clutch with a manual stick shift. Manual transmissions require the driver to shift the gears.Automatic Transmissions Automatic transmissions typically use 3 âforwardâ gears. Each gear is intended to balance speed and torque for the current driving conditions (starting, acceleration, driving up hill, etc). In automatic transmissions, though, is that the gear-shifting process is controlled by oil pressure. A âshift valveâ, controlled by oil pressure, is employed to shift the gears to meet the immediate driving conditions. Your AXLE may be located at the either the front or the rear depending on whether you have front or rear wheel drive. Power from the engine is delivered to the axle by DRIVESHAFT.
42. Torsion springs Also include in the suspension system: shocks, struts and sway bars. Your Carâs Suspension System
43.
44.
45.
46. The electrical system in todayâs cars are complex, and there are dozens of things that can go wrong at any times with the major devices as well as auxiliary devices such as radios, chargers, defrosters, power windows and so on. The Big Three things that you need to pay attention to are: The Battery The Starter Motor The Alternator Your Carâs Electrical System
47.
48. The Battery Your battery stores power to start your car, as well as run all the secondary devices like radios and clocks.The starter Motor The starter motor is a DC solenoid used to start the carâs engine.The Alternator The alternator manages current to keep your car charged while running (it is powered by the engine), and to restore charge to the battery.
49. In old days, car bodyâs were almost entirely metal. These days, however, most car bodies are composite of fiberglass and plastic around a metal frame. Common body problem may include: Rust â In this case, weâre talking about rust from the inside out. This is a bigger problem with older model cars. Accidents â Repairs can get pricey on newer model cars due to their construction. A metal bumper, for example, can be âbangedâ back into some cases. Plastic bumpers, however, usually have to be replaced in full. Paint â UV rays from the sun can damage paint over time. Scratches and dings from rocks, hail or other debris can create chips in the paint leading to further deterioration. Your Carâs Body
50. If you have a newer model car or truck, it is likely that you have disc brakes on all braking wheels, rather than drums. Older models braking system typically employ disc brakes on the front wheels and drum brakes on the back wheels. Why disk brakes? Disc brakes are lighter and perform better than drums in terms of wear and tear. This is because the disc brakes are gripped on either side by the brake pads, similar to the brakes on a cycle. The wear form the heat and friction is distributed evenly. Your Carâs Brakes System
51.
52. A standard brake system consist of 4 main components:1.. Disc and or drums and rotors2. Friction pads3. Master cylinder and brake cylinders4. Brake Fluid The master cylinder connects to your brake pedal via a âpush rodâ. This push rod is then connected to each brakes cylinder by steel brake lines and the rubber hoses that carry the hydraulic brake fluid. Pressure applied to the brake pedal activates the master cylinder pistons which pump brake fluid through the system.
53.
54. The first thing to note is that your heating and AC system is designed to: Add heat to the inside environment, or Remove heat from the inside environment In other words, the cooling of your AC is not achieved by âcreating coldâ, but by removing heat and moisture from the air until the desired temperature is achieved. Your Carâs Heat and AC
55.
56. Your Carâs heating and AC system consist of the following:1. Heater core or âsecondaryâ radiator2. Compressor3. Evaporator4. Condenser5. Fan6. Hoses 7. Liquid refrigerant (Freon, usually R-12 or R-134)In order to heat your car, the system circulates air around the heater core then return it back into the interior of the vehicle. Simple enough, right?The AC system is more elaborate. It starts with the evaporator, which receivesthe air pulled from the interior of the car via a fan. Meanwhile, your compressor is moving refrigerant through a condenser and back to the evaporator.In other words, your AC removes heat from the air by removing the water vapor it on a continual basis as it circulates through the system and back into car.
57.
58. Oil lubricates the moving parts of your engine, protecting them from the wear of friction and high temperatures. What is important here , though, is nit any of the parts of the system but itself. The biggest thing you can do to extend the life of your vehicle is to have the oil changed on regular basis. Most manufactures recommend you get an oil changed every 2 to 3 months or every 2,000 to 3,000 miles. It is vitally important that you use the correct grade and viscosity of oil for your driving conditions. Very cold driving conditions require a thinner viscosity ( the thinner the oil, the faster it heats up) while very hot conditions may require multi-grade or higher viscosity oil Your Carâs Oil
59.
60. Car Basics for Beginners. Everything Youâve Always Wanted to Ask Your Mechanic.Retrieved January 26, 2010, from http://automobile.for-beginners-only.com Reference
61. Prepared by: Utkarsh Kushwah B-Tech (Automotive Design) 2009-13 University of Petroleum & Energy Studies
