Soft x3000 operation manual configuration guide. Part replacement is risky. Before the operation, you must estimate whether the risk can
be controlled with some technical protection measures without powering off the
equipment. If so, you can carry out the replacement; if not, contact the regional office of
Huawei immediately for technical support.After taking corresponding protection measures, you can carry out the replacement
operations by following the procedures stipulated in this manual, for example, pulling
out a board, inserting a board, or setting dual-inline package (DIP) switches of a board.
To make sure the security, only professionals who have been trained can replace the
parts which can be replaced only when the back door of the cabinet is open, because
the power distribution box and service frames are with -48V power terminals.
Notes on Equipment Security
Do not pull out two or more than two UPWRs in one frame simultaneously; otherwise,
the running UPWRs in the frame will be overloaded or even burnt.
Never insert UPWRs of different types into the same frame. The UPWR has two types:
a and b. If the UPWRs of different types are inserted in one frame, the current supplied
by various UPWRs is not even, and the UPWR supplying more current will be
overloaded or even burnt.
Complete the replacement of a fan box within five minutes; otherwise, the security and
normal operation of the corresponding service frame will be greatly affected.
The Most Attractive Pune Call Girls Manchar 8250192130 Will You Miss This Cha...
Soft x3000 operation manual configuration guide
1. Chapter 1 Overview of Configuration Guide 1-1.................................................
1.1 General Configuration Procedure 1-1...........................................................
1.1.1 Overview of General Configuration Procedure 1-1..............................
1.1.2 Configuring Base Data 1-2...................................................................
1.1.3 Configuring Interconnection Data 1-3..................................................
1.1.4 Configuring Service or Application Service 1-3....................................
1.2 Database Operations 1-4.............................................................................
1.2.1 Introduction to Database Operations 1-4.............................................
1.2.2 Format Conversion 1-6........................................................................
1.2.3 Online Setting 1-7................................................................................
1.2.4 CRC Check 1-8....................................................................................
1.2.5 Data Transmission 1-10.........................................................................
1.2.6 Database Backup 1-12...........................................................................
1.2.7 Script Configuration 1-14.......................................................................
1.2.8 Batch File Execution 1-17......................................................................
1.2.9 BAM Database Browse 1-18..................................................................
1.3 Notes on Data Configuration 1-19..................................................................
1.3.1 Rules for Setting MML Command Parameters 1-19..............................
1.3.2 Effect of Maximum Number of Tuples on Data Configuration 1-20........
1.3.3 Effect of Software Parameters on Data Configuration 1-21...................
Chapter 2 Configuring Equipment Information 2-1............................................
2.1 Related Concepts 2-1...................................................................................
2.1.1 Device Numbering 2-1.........................................................................
2.1.2 Module Numbering 2-4.........................................................................
2.1.3 Central Database Function 2-4............................................................
2.1.4 Protocol Dispatch Ability 2-5................................................................
2.2 Configuring Equipment Data 2-6..................................................................
2.2.1 Overview 2-6........................................................................................
2.2.2 Adding Shelf 2-9...................................................................................
2.2.3 Adding Frame 2-10................................................................................
2.2.4 Adding Board 2-10.................................................................................
2.2.5 Adding FE Port Configuration 2-12........................................................
2.2.6 Adding CDB Function 2-13....................................................................
2.2.7 Setting Dispatch Ability (Optional) 2-15.................................................
2.3 Configuring E1 Port and Clock Data 2-16......................................................
2.3.1 Overview 2-16........................................................................................
2.3.2 Adding EPII and CKII Board Data 2-17..................................................
2.3.3 Adding EPII E1 configuration 2-17.........................................................
2.3.4 Adding Board Clock Reference Source (Optional) 2-18........................
2. 2.3.5 Setting CKII Clock Configuration 2-19...................................................
2.3.6 Setting Clock Reference Source of EPII (Optional) 2-20.......................
Chapter 3 Configuring Office Data 3-1.................................................................
3.1 Related Concepts 3-1...................................................................................
3.1.1 Local Office Information 3-1.................................................................
3.1.2 Call Source and DN Set 3-1.................................................................
3.2 Configuring Office Data 3-3..........................................................................
3.2.1 Overview 3-3........................................................................................
3.2.2 Setting Local Office Information 3-6.....................................................
3.2.3 Adding Local Office Signaling Point Code (Optional) 3-11....................
3.2.4 Modifying Local Office Assistant Code (Optional) 3-12..........................
3.2.5 Adding Country or Region Code (Optional) 3-14...................................
3.2.6 Adding National Area Code (Optional) 3-14...........................................
3.2.7 Adding Toll Prefix Description (Optional) 3-15.......................................
3.2.8 Adding Local DN Set 3-16......................................................................
3.2.9 Adding Call Source Code 3-17...............................................................
3.2.10 Adding Subscriber Number Segment 3-22..........................................
3.2.11 Setting Daylight Saving Time (Optional) 3-23......................................
Chapter 4 Configuring Charging Data 4-1...........................................................
4.1 Related Concepts 4-1...................................................................................
4.1.1 Charging Concepts 4-1........................................................................
4.1.2 Charging Case and Charging Source Code 4-5..................................
4.1.3 Charging Method 4-6...........................................................................
4.1.4 Trunk Charging 4-9..............................................................................
4.2 Configuring Basic Charging Data 4-9...........................................................
4.2.1 Overview 4-9........................................................................................
4.2.2 Adding Date Category (Optional) 4-12...................................................
4.2.3 Modifying Week Category (Optional) 4-13.............................................
4.2.4 Adding Charging Case Analysis 4-14....................................................
4.2.5 Modifying Charging Mode 4-18..............................................................
4.2.6 Adding Intra-office Group Charging 4-20...............................................
4.2.7 Adding Charging Case Index 4-21.........................................................
4.2.8 Adding Called Group Charging 4-23......................................................
4.2.9 Adding Supplementary Service Charging 4-24......................................
4.3 Configuring Addition Fee Data 4-25...............................................................
4.3.1 Overview 4-25........................................................................................
4.3.2 Adding Additional Fee Charging Mode (Optional) 4-26.........................
4.3.3 Modifying Additional Fee Charging Mode 4-27......................................
4.4 Configuring CRG Charging Data 4-29............................................................
3. 4.4.1 Overview 4-29........................................................................................
4.4.2 Configuring Related ISUP Adaptation Data 4-30...................................
4.4.3 Modifying Fixed Software Parameter 4-30.............................................
4.4.4 Adding Tariff Indicator (Optional) 4-31...................................................
4.4.5 Adding Time Indicator (Optional) 4-32...................................................
4.4.6 Adding Charging Band 4-34...................................................................
4.4.7 Adding Charging Case Analysis 4-36....................................................
4.4.8 Adding Charging Case Index 4-36.........................................................
4.5 Other Charging-related Configurations 4-36..................................................
4.5.1 Modifying Charging Number 4-36..........................................................
4.5.2 Modifying Meter Tariff Rate 4-37............................................................
4.5.3 Checking Charging Configuration (Charging Emulation) 4-37...............
4.5.4 Adding Conversation Duration Control 4-38..........................................
4.5.5 Adding Charging Pulse Control 4-40......................................................
4.5.6 Adding Charging Case Change 4-42.....................................................
4.5.7 Adding charging band number change 4-43..........................................
4.5.8 Adding Caller Charge Failure Processing 4-45......................................
4.5.9 Adding Callee Charge Failure Processing 4-47.....................................
Chapter 5 Configuring MG Data 5-1.....................................................................
5.1 Related Concepts 5-1...................................................................................
5.1.1 Types of Media Gateways 5-1.............................................................
5.1.2 Media Stream Codec Mode 5-2...........................................................
5.1.3 Gateway Registration Mode 5-4...........................................................
5.2 Configuring Gateway Data 5-5.....................................................................
5.2.1 Overview 5-5........................................................................................
5.2.2 Setting MGCP Protocol Parameter (Optional) 5-8...............................
5.2.3 Setting Diffie-Hellman Authentication P Parameter (Optional) 5-9......
5.2.4 Adding Termination ID Layer Configuration (Optional) 5-10..................
5.2.5 Adding Media Gateway 5-12..................................................................
5.2.6 Adding a Multimedia Device 5-22..........................................................
5.2.7 Adding a Batch of Multimedia Devices 5-24..........................................
5.3 Configuring VIG Data 5-25.............................................................................
5.3.1 Overview 5-25........................................................................................
5.3.2 Adding VIG 5-27.....................................................................................
5.3.3 Adding VIG H.245 Link 5-28..................................................................
5.3.4 Adding VIG Gateway Capabilities 5-30..................................................
Chapter 6 Configuring MRS Data 6-1...................................................................
6.1 Related Concepts 6-1...................................................................................
6.1.1 MRS 6-1...............................................................................................
4. 6.1.2 MRS Networking Mode 6-2..................................................................
6.1.3 MRS Voice Categories 6-4...................................................................
6.1.4 Voice File Description 6-5....................................................................
6.2 Configuring Embedded MRS Data 6-7.........................................................
6.2.1 Overview 6-7........................................................................................
6.2.2 Adding MRCA Board 6-10......................................................................
6.2.3 Adding MRC Configuration 6-11............................................................
6.2.4 Adding MRP Configuration 6-12............................................................
6.2.5 Adding MRC Voice File 6-15..................................................................
6.2.6 Adding Mapping Relation between Tone ID and Voice File
(Optional) 6-16................................................................................................
6.2.7 Adding Language Zone (Optional) 6-17.................................................
6.2.8 Adding Tone ID Configuration (Optional) 6-18.......................................
6.2.9 Adding Mapping Relation between Release Cause Value and
Tone ID (Optional) 6-20..................................................................................
6.3 Configuring External MRS Data 6-22.............................................................
6.3.1 Overview 6-22........................................................................................
6.3.2 Adding MRS Gateway 6-24....................................................................
6.3.3 Adding MRS Route (Only for MRS6000) 6-25.......................................
6.3.4 Adding Mapping between Tone ID and Tone File (Optional) 6-25.........
6.3.5 Adding Language Zone (Optional) 6-26.................................................
6.3.6 Adding Tone ID Configuration (Optional) 6-27.......................................
6.3.7 Adding Mapping between Cause Value and Tone ID (Optional) 6-29...
Chapter 7 Configuring Protocol Data 7-1............................................................
7.1 Related Concepts 7-1...................................................................................
7.1.1 SIP 7-1.................................................................................................
7.1.2 H.323 7-2.............................................................................................
7.2 Configuring SIP Data 7-4..............................................................................
7.2.1 Overview 7-4........................................................................................
7.2.2 Setting SIP Global Configuration 7-5...................................................
7.2.3 Setting SIP Local Port 7-7....................................................................
7.3 Configuring H.323 Data 7-8..........................................................................
7.3.1 Overview 7-8........................................................................................
7.3.2 Adding H.323 System Information 7-9.................................................
7.3.3 Adding H.323 Application Information 7-10............................................
7.4 Configuring STUN Data 7-11..........................................................................
7.4.1 Overview 7-11........................................................................................
7.4.2 Adding STUN Protocol Dispatch 7-12....................................................
7.4.3 Setting Dispatch Ability 7-12..................................................................
Chapter 8 Configuring Signaling Data 8-1...........................................................
5. 8.1 Related Concepts 8-2...................................................................................
8.1.1 SIGTRAN 8-2.......................................................................................
8.1.2 SS7 8-4................................................................................................
8.1.3 V5 Interface Protocol 8-7.....................................................................
8.1.4 DSS1 8-9..............................................................................................
8.1.5 Mask 8-9..............................................................................................
8.2 Configuring M2UA Data 8-11.........................................................................
8.2.1 Overview 8-11........................................................................................
8.2.2 Adding Embedded Signaling Gateway 8-13..........................................
8.2.3 Adding M2UA Linkset 8-14....................................................................
8.2.4 Adding M2UA Link 8-15.........................................................................
8.3 Configuring M3UA Data 8-18.........................................................................
8.3.1 Overview 8-18........................................................................................
8.3.2 Adding M3UA Local Entity 8-20.............................................................
8.3.3 Adding M3UA Destination Entity 8-22....................................................
8.3.4 Adding M3UA Additional Destination Service (Optional) 8-25...............
8.3.5 Adding M3UA Link Set 8-26...................................................................
8.3.6 Adding M3UA Link 8-28.........................................................................
8.3.7 Adding M3UA Route 8-31......................................................................
8.4 Configuring V5UA Data 8-32..........................................................................
8.4.1 Overview 8-32........................................................................................
8.4.2 Adding Embedded Signaling Gateway 8-34..........................................
8.4.3 Adding V5UA Link Set 8-35...................................................................
8.4.4 Adding V5UA Link 8-36..........................................................................
8.5 Configuring IUA Data 8-39.............................................................................
8.5.1 Overview 8-39........................................................................................
8.5.2 Adding Embedded Signaling Gateway 8-41..........................................
8.5.3 Adding IUA Link Set 8-42.......................................................................
8.5.4 Adding IUA Link 8-43.............................................................................
8.6 Configuring MTP Data 8-46............................................................................
8.6.1 Overview 8-46........................................................................................
8.6.2 Adding MTP Destination Signaling Point 8-48.......................................
8.6.3 Adding MTP Link Set 8-50.....................................................................
8.6.4 Adding MTP Link 8-52............................................................................
8.6.5 Adding MTP Route 8-56.........................................................................
8.7 Configuring SCCP Data 8-57.........................................................................
8.7.1 Overview 8-57........................................................................................
8.7.2 Adding SCCP Destination Signaling Point 8-59.....................................
8.7.3 Adding SCCP Subsystem 8-61..............................................................
8.7.4 Adding SCCP New Global Title (Optional) 8-63.....................................
8.7.5 Adding SCCP Global Title (Optional) 8-64.............................................
6. 8.8 Configuring V5 Interface Data 8-66................................................................
8.8.1 Overview 8-66........................................................................................
8.8.2 Adding V5 Interface 8-69.......................................................................
8.8.3 Adding V5 Variant (Optional) 8-72.........................................................
8.9 Configuring PRA Link Data 8-74....................................................................
8.9.1 Overview 8-74........................................................................................
8.9.2 Adding PRA Link 8-76............................................................................
Chapter 9 Configuring Routing Data 9-1.............................................................
9.1 Related Concepts 9-1...................................................................................
9.1.1 Office Direction, Sub-route and Route 9-1...........................................
9.1.2 Route Selection Source Code and Route Selection Code 9-2.............
9.1.3 Route Analysis Process 9-2.................................................................
9.1.4 Hierarchical Route Networking in NGN 9-4..........................................
9.2 Configuring Routing Data 9-6.......................................................................
9.2.1 Overview 9-6........................................................................................
9.2.2 Adding Office Direction 9-9..................................................................
9.2.3 Adding Sub-Route 9-13..........................................................................
9.2.4 Adding Route 9-14.................................................................................
9.2.5 Adding Time Index (Optional) 9-17........................................................
9.2.6 Adding Route Analysis 9-19...................................................................
9.3 Configuring Location Server Data 9-21..........................................................
9.3.1 Overview 9-21........................................................................................
9.3.2 Adding Location Server 9-22..................................................................
9.3.3 Setting Location Server Agent 9-23.......................................................
9.3.4 Activating Location Server Link 9-25......................................................
Chapter 10 Configuring Trunk Data 10-1...............................................................
10.1 Related Concepts 10-2.................................................................................
10.1.1 SIP Trunk 10-2.....................................................................................
10.1.2 H.323 Trunk 10-3.................................................................................
10.1.3 No. 7 Trunk 10-6..................................................................................
10.1.4 R2 Trunk 10-6......................................................................................
10.1.5 PRA Trunk 10-10...................................................................................
10.1.6 AT0 Trunk 10-10....................................................................................
10.1.7 V5 Trunk 10-11......................................................................................
10.2 Configuring SIP Trunk Data 10-12.................................................................
10.2.1 Overview 10-12......................................................................................
10.2.2 Adding SIP Trunk Group 10-13..............................................................
10.3 Configuring H.323 Trunk Data 10-19..............................................................
10.3.1 Overview 10-19......................................................................................
7. 10.3.2 Adding Virtual IP List (Optional) 10-21...................................................
10.3.3 Adding H.323 Trunk Group 10-22..........................................................
10.4 Configuring No. 7 Trunk Data 10-27...............................................................
10.4.1 Overview 10-27......................................................................................
10.4.2 Add Carrier Access Code (optional) 10-29............................................
10.4.3 Adding Carrier Selection Code (optional) 10-30....................................
10.4.4 Add Originating Network ID (optional) 10-31.........................................
10.4.5 Adding No. 7 Trunk Group 10-32...........................................................
10.4.6 Adding No. 7 Trunk Circuit 10-49...........................................................
10.4.7 Adding PCM Port (Optional) 10-51........................................................
10.5 Configuring R2 Trunk Data 10-52...................................................................
10.5.1 Overview 10-52......................................................................................
10.5.2 Adding R2 Incoming Caller Category Conversion (Optional) 10-55.......
10.5.3 Adding R2 Outgoing Caller Category Conversion (Optional) 10-56.......
10.5.4 Adding CAS Signaling Configuration 10-57...........................................
10.5.5 Adding R2 Trunk Group 10-58...............................................................
10.5.6 Adding R2 Trunk Circuit 10-73...............................................................
10.5.7 Adding R2 Trunk Group Tandem (Optional) 10-76................................
10.5.8 Adding R2 Trunk Group Caller Number Segment (Optional) 10-78.......
10.6 Configuring PRA Trunk Data 10-79................................................................
10.6.1 Overview 10-79......................................................................................
10.6.2 Adding PRA Trunk Group 10-81............................................................
10.6.3 Adding PCM Port (Optional) 10-86........................................................
10.6.4 Adding PRA Trunk Circuit 10-87............................................................
10.7 Configuring AT0 Trunk Data 10-89.................................................................
10.7.1 Overview 10-89......................................................................................
10.7.2 Adding AT0 Trunk Group 10-90.............................................................
10.7.3 Adding AT0 Trunk Circuit 10-94.............................................................
10.8 Configuring V5 Trunk Data 10-95...................................................................
10.8.1 Overview 10-95......................................................................................
10.8.2 Adding V5 Trunk Group 10-97...............................................................
10.8.3 Adding V5 Trunk Circuit 10-98...............................................................
10.9 Configuring Trunk Group Bearer Data 10-100.................................................
10.9.1 Overview 10-100......................................................................................
10.9.2 Adding TOS Changing Index (Optional) 10-101......................................
10.9.3 Adding Trunk Group Bearer 10-102.........................................................
10.9.4 Adding Trunk Group Bearer Index 10-105...............................................
10.10 Other Commands 10-106...............................................................................
10.10.1 Adding Trunk Group Append Configuration 10-106...............................
10.10.2 Adding Caller Category Transform Index 10-109...................................
10.10.3 Adding Internal Caller Category Transform 10-110...............................
8. Chapter 11 Configuring Number Analysis Data 11-1............................................
11.1 Related Concepts 11-1.................................................................................
11.1.1 Call Prefix 11-1.....................................................................................
11.1.2 Digit Map 11-2......................................................................................
11.1.3 Number Change 11-4...........................................................................
11.1.4 Sequence of Number Analysis 11-7.....................................................
11.2 Configuring Number Analysis Data 11-7......................................................
11.2.1 Overview 11-7......................................................................................
11.2.2 Modifying Local DN Set (Optional) 11-11...............................................
11.2.3 Adding Called Number Analysis 11-12..................................................
11.3 Other Commands 11-21.................................................................................
11.3.1 Setting Prefix Priority (Optional) 11-21...................................................
11.3.2 Setting Release Control Mode 11-22.....................................................
11.3.3 Adding Cause Code Conversion (Optional) 11-24.................................
11.3.4 Adding Preselection Access Code Index (Optional) 11-25....................
11.3.5 Adding Number Change (Optional) 11-27..............................................
11.3.6 Adding Special Called Number Change (Optional) 11-29......................
11.3.7 Adding Caller Number Analysis (Optional) 11-31..................................
11.3.8 Adding Call Prefix Processing (Optional) 11-34.....................................
11.3.9 Adding Call Failure Processing (Optional) 11-37...................................
11.3.10 Adding Auxiliary Signaling (Optional) 11-40.........................................
Chapter 12 Configuring Subscriber Data 12-1......................................................
12.1 Related Concepts 12-1.................................................................................
12.1.1 Subscriber Terminal Category 12-1.....................................................
12.1.2 Identification of Subscriber Line Physical Port 12-2.............................
12.1.3 ISDN Subscriber-Network Interface 12-4.............................................
12.2 Configuring Ordinary Subscriber Data 12-6.................................................
12.2.1 Overview 12-6......................................................................................
12.2.2 Adding a Voice Subscriber 12-9...........................................................
12.2.3 Adding a Batch of Voice Subscribers 12-20...........................................
12.2.4 Adding a Multimedia Subscriber 12-22..................................................
12.2.5 Adding a Batch of Multimedia Subscribers 12-24..................................
12.2.6 Adding a Wide Area Centrex Subscriber 12-26.....................................
12.2.7 Adding a Batch of Wide Area Centrex Subscribers 12-27.....................
12.3 Configuring ISDN Subscriber Data 12-28.......................................................
12.3.1 Overview 12-28......................................................................................
12.3.2 Adding ISDN Data 12-32........................................................................
12.3.3 Adding a BRA Subscriber 12-33............................................................
12.3.4 Adding a Batch of BRA Subscribers 12-37............................................
9. 12.3.5 Adding a PRA Subscriber 12-40............................................................
12.4 Configuring Other Subscriber Data 12-44......................................................
12.4.1 Adding Multi-Subscriber Number 12-44.................................................
12.4.2 Setting String of Anonymous Card Flag 12-46.......................................
Chapter 13 Configuring Centrex Data 13-1............................................................
13.1 Related Concepts 13-1.................................................................................
13.1.1 Centrex Prefix and Centrex Out-Group Prefix 13-1.............................
13.1.2 IP Console and IP Supermarket 13-2..................................................
13.2 Configuring Centrex Data 13-2.....................................................................
13.2.1 Overview 13-2......................................................................................
13.2.2 Adding Centrex Group 13-6.................................................................
13.2.3 Adding Centrex Intra-Group Prefix 13-10...............................................
13.2.4 Adding Centrex Out-Group Prefix (Optional) 13-14...............................
13.2.5 Adding Centrex Prefix Special Processing (Optional) 13-15..................
13.2.6 Adding Centrex Intra-Group Charging (Optional) 13-19........................
13.2.7 Adding Centrex Out-Group Authority (Optional) 13-20..........................
13.2.8 Adding Centrex Group Abbreviated Dialing (Optional) 13-21................
13.2.9 Adding Centrex Subscriber Status Subscribing (Optional) 13-22..........
13.2.10 Setting Local IP Address for Controlling Console 13-23......................
13.2.11 Adding IP Console 13-24.....................................................................
13.2.12 Adding ISDN Centrex console 13-29...................................................
13.2.13 Modifying Centrex Group (Optional) 13-32..........................................
Chapter 14 Configuring Call Barring Data 14-1.....................................................
14.1 Related Concepts 14-1.................................................................................
14.1.1 Caller Number Discrimination 14-1......................................................
14.1.2 Inter-Group Call Barring and Black and White Lists 14-2....................
14.1.3 Time-Based Call Restriction 14-4........................................................
14.1.4 Other Call Restriction Methods 14-5....................................................
14.1.5 Analysis of Number Restriction 14-5....................................................
14.1.6 Applications of Call Barring Data 14-8.................................................
14.2 Configuring Call Barring Data 14-9...............................................................
14.2.1 Overview 14-9......................................................................................
14.2.2 Modifying Call Source Code 14-11........................................................
14.2.3 Adding Caller Number Discrimination Group 14-13...............................
14.2.4 Adding Trunk Discrimination Group 14-18.............................................
14.2.5 Setting Inter-Group Call Barring Indication 14-19..................................
14.2.6 Adding Called Number Barring Group 14-20.........................................
14.2.7 Adding Call Timingly Restriction Group 14-22.......................................
Chapter 15 Configuring IN Service Data 15-1........................................................
10. 15.1 Related Concepts 15-2.................................................................................
15.1.1 Architecture of Standard IN 15-2..........................................................
15.1.2 Architecture of Local IN 15-4................................................................
15.1.3 IN Charging Principles 15-6.................................................................
15.1.4 Recorded Announcement Message ID 15-7........................................
15.1.5 Naming Conventions for Intelligent Voice Files 15-10...........................
15.2 Configuring IN Charging Data 15-12..............................................................
15.2.1 Overview 15-12......................................................................................
15.2.2 Adding Holiday Tariff Discount (Optional) 15-13....................................
15.2.3 Adding Weekday Tariff Discount (Optional) 15-16.................................
15.2.4 Adding Normal Tariff Discount (Optional) 15-17....................................
15.2.5 Adding Conversation Duration Discount (Optional) 15-18.....................
15.2.6 Adding Charging Class 15-19................................................................
15.2.7 Adding Charging Property (Optional) 15-20...........................................
15.2.8 Adding Charging Rounding (Optional) 15-22.........................................
15.3 Configuring DP Data 15-23............................................................................
15.3.1 Overview 15-23......................................................................................
15.3.2 Setting INAP Protocol Type (Optional) 15-25........................................
15.3.3 Adding Called Number Analysis 15-26..................................................
15.3.4 Adding Access Code 15-28....................................................................
15.3.5 Adding TDP Configuration 15-29...........................................................
15.3.6 Set DP Trigger Configuration (Optional) 15-33......................................
15.3.7 Add Mapping Between Service Key and Event Code
(Optional) 15-34................................................................................................
15.3.8 Adding IN Service Restriction (Optional) 15-35.....................................
15.4 Configuring SCP and SSP Data 15-37...........................................................
15.4.1 Overview 15-37......................................................................................
15.4.2 Adding SCP Physical Address Description 15-39..................................
15.4.3 Adding SSP Physical Address Description 15-41..................................
15.4.4 Adding SCP Configuration 15-44...........................................................
15.4.5 Adding SSP Service Specialized Resource Capability
(Optional) 15-45................................................................................................
15.4.6 Adding SCP Number Mapping (Optional) 15-45....................................
15.5 Configuring SHLR Data 15-47........................................................................
15.5.1 Overview 15-47......................................................................................
15.5.2 Adding SHLR Local Address 15-48.......................................................
15.5.3 Adding SHLR Remote Address 15-50...................................................
15.5.4 Adding SHLR Group 15-51....................................................................
15.5.5 Adding SHLR Configuration 15-52.........................................................
15.5.6 Adding SHLR Service Configuration (Optional) 15-56...........................
15.6 Configuring SSAP Data 15-59........................................................................
11. 15.6.1 Overview 15-59......................................................................................
15.6.2 Adding INAP over IP 15-60....................................................................
15.6.3 Adding Module Dialog Number 15-61....................................................
15.7 Configuring IN Announcement Data 15-62.....................................................
15.7.1 Overview 15-62......................................................................................
15.7.2 Loading IN Voice Files to MRS 15-64....................................................
15.7.3 Adding Language Kind (Optional) 15-64................................................
15.7.4 Adding Language Kind Index 15-66.......................................................
15.7.5 Adding Money Category (Optional) 15-67..............................................
15.7.6 Adding Record Announcement Message ID Conversion
(Optional) 15-68................................................................................................
15.7.7 Adding Mapping between Message ID and Tone ID (Optional) 15-69...
15.8 Special Configuration Commands 15-70........................................................
15.8.1 Adding IN Service Special Signaling 15-70............................................
15.8.2 Adding Caller Description of Local IN Call 15-71...................................
15.8.3 Adding Network Access Code 15-72.....................................................
Chapter 16 Configuring UC Service Data 16-1......................................................
16.1 Related Concepts 16-1.................................................................................
16.1.1 Architecture of UC System 16-1...........................................................
16.1.2 UC Intelligent Calling Routing 16-3......................................................
16.2 Configuring UC Service Data 16-4...............................................................
16.2.1 Overview 16-4......................................................................................
16.2.2 Adding UC Agent Server 16-7..............................................................
16.2.3 Adding UC Application Server 16-9.....................................................
16.2.4 Adding UC Subscriber 16-9.................................................................
16.2.5 Adding Workstation 16-12......................................................................
16.2.6 Adding UC Caller Group (Optional) 16-12.............................................
16.2.7 Adding UC Date Information (Optional) 16-14.......................................
16.2.8 Adding UC Presence Status Data (Optional) 16-15...............................
16.2.9 Setting UC Presence Status Data (Optional) 16-16...............................
16.2.10 Adding UC Profile (Optional) 16-17......................................................
16.2.11 Setting UC Profile (Optional) 16-18......................................................
16.2.12 Adding UC Intelligent Calling Routing (Optional) 16-18.......................
Chapter 17 Configuring Network Management Data 17-1....................................
17.1 Background Knowledge 17-1.......................................................................
17.1.1 Overview to Network Management Instructions 17-1..........................
17.1.2 Purposes of Network Management Instructions 17-1..........................
17.2 Configuring NM Instructions 17-6.................................................................
17.2.1 Adding Originating Destination Code Control 17-6..............................
17.2.2 Adding Outgoing Destination Code Control 17-8.................................
12. 17.2.3 Adding Call Gap Control 17-9..............................................................
17.2.4 Adding Circuit Orient Control 17-11.......................................................
17.2.5 Adding Circuit Reject Control 17-12.......................................................
17.2.6 Adding Direct Route Control 17-13........................................................
17.2.7 Adding Alternative Route Cancellation Control 17-14............................
17.2.8 Adding Temporary Alternative Route Control 17-15..............................
17.2.9 Adding Skip Sub-Route Control 17-17...................................................
17.2.10 Adding Special Record Notification Control 17-18...............................
17.2.11 Adding Trunk Reserved Control 17-20.................................................
17.3 HTR Control Instructions 17-21......................................................................
17.3.1 Adding HTR Description 17-21..............................................................
17.3.2 Setting HTR Switch 17-24......................................................................
17.3.3 Removing HTR Control Table Content 17-24........................................
Chapter 18 Configuring Other Data 18-1...............................................................
18.1 Related Concepts 18-1.................................................................................
18.1.1 Dual-homing 18-1.................................................................................
18.1.2 PBX Service 18-4.................................................................................
18.1.3 Videoconferencing Service 18-5..........................................................
18.1.4 NP Service (Hong Kong) 18-7..............................................................
18.2 Configuring Dual-homing Data 18-8.............................................................
18.2.1 Overview 18-8......................................................................................
18.2.2 Setting Dual-homing Work Mode 18-10.................................................
18.2.3 Adding Dual-homing Heartbeat Configuration 18-12.............................
18.3 Configuring PBX Service Data 18-13.............................................................
18.3.1 Overview 18-13......................................................................................
18.3.2 Adding PBX Group 18-15.......................................................................
18.3.3 Adding PBX Subscriber 18-17...............................................................
18.3.4 Adding PBX Virtual Subscribers 18-18..................................................
18.4 Configuring Videoconferencing Service Data 18-20.......................................
18.4.1 Overview 18-20......................................................................................
18.4.2 Adding MCU Configuration 18-21..........................................................
18.4.3 Adding iDo and SMC 18-23...................................................................
18.4.4 Adding Called Number Analysis 18-24..................................................
18.5 Configuring NP Service Data (Hong Kong) 18-25..........................................
18.5.1 Overview 18-25......................................................................................
18.5.2 Adding NP Server 18-27........................................................................
18.5.3 Adding Connection to NP Server 18-28.................................................
18.5.4 Adding Mapping between Network Number and Telephone
Number (Optional) 18-29..................................................................................
18.6 Configuring RACF Card Number 18-30..........................................................
13. 18.6.1 Overview 18-30......................................................................................
18.6.2 Configuring DP, SCP, and SSP Data 18-30..........................................
18.6.3 Add CSP Service Configuration 18-31...................................................
18.6.4 Adding CSP Service Logic File 18-33....................................................
18.6.5 Activating CSP Service Logic File 18-34................................................
18.6.6 Adding CSP Service Module Configuration 18-34.................................
18.6.7 Adding RACF Number Segment 18-35..................................................
18.6.8 Adding RACF Number 18-36.................................................................
18.7 Configuring Supplementary Service Data 18-36............................................
18.7.1 Modifying Special Tone Configuration 18-36.........................................
18.7.2 Adding Service Processing Configuration 18-37....................................
18.7.3 Modifying Supplementary Service Analysis 18-39.................................
18.7.4 Modifying Supplementary Service Collision Configuration 18-46..........
18.7.5 Modifying Supplementary Service Priority Configuration 18-47.............
18.7.6 Adding Call Forwarding Restriction 18-48..............................................
18.7.7 Adding Call Forwarding Data 18-49.......................................................
18.7.8 Setting MWN Service Configuration 18-50............................................
Appendix A Configuring SNTP Client A-1............................................................
A.1 Overview A-1................................................................................................
A.2 Guide to Data Configuration A-3..................................................................
Appendix B Basic Principles of CRG Charging B-1............................................
B.1 Overview B-1................................................................................................
B.1.1 Basic Concepts B-1..............................................................................
B.1.2 Charging Mode and Charging Process B-2.........................................
B.2 CRG Charging Process B-3.........................................................................
B.2.1 Charging Process of the First Class (CHG/TAC) B-3..........................
B.2.2 Charging Process of the Second Class (CHB/CHP) B-6.....................
B.2.3 Charging Process of the Third Class (CRG) B-9.................................
B.2.4 Special Cases of the CHP/CRG Charging Modes B-10.........................
Appendix C Tone ID C-1.........................................................................................
Appendix D Acronyms and Abbreviations D-1....................................................
15. Huawei Technologies Proprietary
U-SYS SoftX3000 SoftSwitch System
Operation Manual
Volume Configuration Guide
Manual Version T2-011627-20050331-C-3.30
Product Version V300R003
BOM 31161627
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support
and service. Please feel free to contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co., Ltd.,
Bantian, Longgang District, Shenzhen, P. R. China
Postal Code: 518129
Website: http://www.huawei.com
Email: support@huawei.com
17. Huawei Technologies Proprietary
About This Manual
Release Notes
This manual applies to U-SYS SoftX3000 SoftSwitch System V300R003 (hereinafter
referred to as SoftX3000).
Related Manuals
The related manuals are listed in the following table.
Manual Content
U-SYS SoftX3000 SoftSwitch
System Technical
Manual-System Description
It provides an overall introduction to the
SoftX3000, including product features,
applications, and technical specifications.
U-SYS SoftX3000 SoftSwitch
System Technical
Manual-System Principle
It details on the hardware architecture,
component interworking mechanism, and
subsystems of alarm, billing, and clock in the
SoftX3000.
U-SYS SoftX3000 SoftSwitch
System Hardware Description
Manual
It details the features and technical
specifications of the hardware components of
the SoftX3000, including cabinets, frames,
boards, cables, and cabinet internal
components.
U-SYS SoftX3000 SoftSwitch
System Technical
Manual–Services and Features
It covers various services and functions
supported by the SoftX3000, including voice
services, supplementary services, IP Centrex
services, multi-media services, value added
services, dual homing functions, charging
functions, IPTN functions, remote network
access functions, and so on.
U-SYS SoftX3000 SoftSwitch
System Hardware Installation
Manual
It details the installation procedure of the
SoftX3000 hardware components, and matters
needing attention during the installation
process.
U-SYS SoftX3000 SoftSwitch
System Software Installation
Manual
It covers the detailed procedure of installing the
SoftX3000 software, including BAM server,
emergency workstation, and client, focusing on
the key points that might cause installation
failure.
U-SYS SoftX3000 SoftSwitch
System Routine Maintenance
Guide
It guides the maintenance engineers to perform
daily maintenance, monthly maintenance, and
yearly maintenance tasks on the SoftX3000.
18. Huawei Technologies Proprietary
Manual Content
U-SYS SoftX3000 SoftSwitch
System Emergency
Maintenance Manual
It guides the maintenance engineers to perform
recovery operations in the case of emergencies,
such as congestion of global service, AMG, and
TMG, and failure of host and BAM.
U-SYS SoftX3000 SoftSwitch
System Part Replacement Guide
It guides the maintenance engineers on how to
replace hardware components of the
SoftX3000, such as boards, fan frame, LAN
Switch, and hard disk.
U-SYS SoftX3000 SoftSwitch
System Operation
Manual-Configuration Guide
It guides the engineers how to configure various
data in the SoftX3000, including configuration
steps, preparations, database table referencing
relationships, and command parameters.
U-SYS SoftX3000 SoftSwitch
System Operation
Manual-Configuration Examples
It guides the engineers how to configure various
data in the SoftX3000, including networking
example, configuration script, key parameters
and debugging guidance.
U-SYS SoftX3000 SoftSwitch
System Operation
Manual-Performance
Measurement
It guides the engineers how to work on
performance measurement tasks and analyze
measurement results.
U-SYS SoftX3000 SoftSwitch
System Operation Manual-GUI
Guide
It guides the engineers how to use the GUI on
various clients of the SoftX3000, including
operations on menus and navigation tree. In
addition, it introduces the operations on
TableBrowse.
U-SYS SoftX3000 SoftSwitch
System BAM User Manual
It guides the engineers how to install and use
the software related to the BAM, including
remote maintenance software, anti-virus
software, system customized software, and so
on.
U-SYS iGateway Bill User
Manual
It elaborates on the functioning principle of the
iGateway Bill. Also, it teaches you on how to
install, maintain, and operate the product.
Organization
The manual explains how to configure various data in U-SYS SoftX3000 SoftSwitch
System.
Chapter 1 Overview of Configuration Guide is a brief introduction to the data
configuration in SoftX3000, such as general principles for the data configuration, a
general data configuration process, basic operations, and necessary attentions.
Chapter 2 Configuring Equipment Information provides steps for configuring
equipment information of SoftX3000 such as racks, frames, and boards.
19. Huawei Technologies Proprietary
Chapter 3 Configuring Office Data explains how to configure local office data
including signaling point code, country/region code, toll area code, local DN set,
global DN set, and call source.
Chapter 4 Configuring Charging Data teaches how to configure ordinary
charge-related data.
Chapter 5 Configuring MG Data introduces how to configure various media
gateways including integrated access device, access media gateway, trunk media
gateway, universal media gateway, and multimedia gateway.
Chapter 6 Configuring MRS Data provides detailed steps for configuring
resource data regarding an embedded media resource server or a physically
separate media resource server.
Chapter 7 Configuring Protocol Data details how to configure protocol related
data such as Session Initiation Protocol (SIP), H.323, and Simple Traversal of
UDP Through Network Address Translators (STUN).
Chapter 8 Configuring Signaling Data describes in detail how to configure
signaling-related data such as Message Transfer Part 2-User Adaptation Layer
(M2UA), Message Transfer Part 3-User Adaptation Layer (M3UA), V5.2-User
Adaptation Layer (V5UA), ISDN Q.921-User Adaptation Layer (IUA), Message
Transfer Part (MTP), Signaling Connection and Control Part (SCCP), V5 interface,
and Primary Rate Access (PRA).
Chapter 9 Configuring Routing Data provides detailed steps for configuring
static routing data.
Chapter 10 Configuring Trunk Data explains how to configure trunk-related data
such as No. 7 trunk, R2 trunk, SIP trunk, H.323 trunk, V5 trunk, and PRA trunk.
Chapter 11 Configuring Number Analysis Data teaches how to configure call
prefix, number change, release mode, number initial processing, and failure
processing.
Chapter 12 Configuring Subscriber Data covers configuration steps regarding
ordinary subscribers and ISDN subscribers.
Chapter 13 Configuring Centrex Data explains how to configure a Centrex
group, Centrex subscribers, and an IP console.
Chapter 14 Configuring Call Barring Data covers configuration steps regarding
number discrimination, black and white lists, inter-group call barring relationship,
and network management commands.
Chapter 15 Configuring IN Service Data details how to configure Intelligent
Network (IN) service data, such as IN charging data, Detection Point (DP) data,
Service Control Point (SCP) data, Service Switching Point (SSP) data, and
recorded announcements.
Chapter 16 Configuring UC Service Data presents steps for configuring the
Unified Communication (UC) service.
Chapter 17 Configuring Network Management Data details how to configure
NM instructions.
20. Huawei Technologies Proprietary
Chapter 18 Configuring Other Data provides configuration steps regarding
Private Branch Exchange (PBX) service, videoconferencing service and dual
homing data.
Appendix A Configuring SNTP Client presents how to configure Simple
Network Time Protocol (SNTP) client.
Appendix B Basic Principles of CRG Charging elaborates the basic principle
and processing of CRG charging.
Appendix C Tone ID introduces the parameter values and meanings of the signal
tone IDs and supplementary service tone IDs that are supported by SoftX3000.
Appendix D Acronyms and Abbreviations lists frequently used acronyms and
abbreviations as well as their full names in this manual..
Intended Audience
The manual is intended for the following readers:
NGN engineering specialist
NGN operation & maintenance personnel
NGN network planning experts
Conventions
The manual uses the following conventions:
I. General conventions
Convention Description
Arial Normal paragraphs are in Arial.
Boldface Headings are in Boldface.
Courier New Terminal Display is in Courier New.
II. Command conventions
Convention Description
Boldface The keywords of a command line are in Boldface.
italic Command arguments are in italic.
[ ]
Items (keywords or arguments) in square brackets [ ] are
optional.
{ x | y | ... }
Alternative items are grouped in braces and separated by
vertical bars. One is selected.
21. Huawei Technologies Proprietary
Convention Description
[ x | y | ... ]
Optional alternative items are grouped in square brackets
and separated by vertical bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces and separated by
vertical bars. A minimum of one or a maximum of all can be
selected.
[ x | y | ... ] *
Optional alternative items are grouped in square brackets
and separated by vertical bars. Many or none can be
selected.
III. GUI conventions
Convention Description
< >
Button names are inside angle brackets. For example, click
the <OK> button.
[ ]
Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
/
Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
IV. Keyboard operation
Format Description
<Key>
Press the key with the key name inside angle brackets. For
example, <Enter>, <Tab>, <Backspace>, or <A>.
<Key1+Key2>
Press the keys concurrently. For example, <Ctrl+Alt+A>
means the three keys should be pressed concurrently.
<Key1, Key2>
Press the keys in turn. For example, <Alt, A> means the
two keys should be pressed in turn.
V. Mouse operation
Action Description
Click
Press the left button or right button quickly (left button by
default).
Double Click Press the left button twice continuously and quickly.
Drag
Press and hold the left button and drag it to a certain
position.
22. Huawei Technologies Proprietary
VI. Symbols
Eye-catching symbols are also used in the manual to highlight the points worthy of
special attention during the operation. They are defined as follows:
Caution, Warning, Danger: Means reader be extremely careful during the
operation.
Note, Comment, Tip, Knowhow, Thought: Means a complementary description
23. Operation Manual - Configuration Guide
U-SYS SoftX3000 SoftSwitch System Table of Contents
Huawei Technologies Proprietary
i
Table of Contents
Chapter 1 Overview of Configuration Guide .............................................................................. 1-1
1.1 General Configuration Procedure...................................................................................... 1-1
1.1.1 Overview of General Configuration Procedure ....................................................... 1-1
1.1.2 Configuring Base Data............................................................................................ 1-2
1.1.3 Configuring Interconnection Data............................................................................ 1-3
1.1.4 Configuring Service or Application Service............................................................. 1-3
1.2 Database Operations......................................................................................................... 1-4
1.2.1 Introduction to Database Operations ...................................................................... 1-4
1.2.2 Format Conversion.................................................................................................. 1-6
1.2.3 Online Setting.......................................................................................................... 1-7
1.2.4 CRC Check ............................................................................................................. 1-8
1.2.5 Data Transmission ................................................................................................ 1-10
1.2.6 Database Backup.................................................................................................. 1-12
1.2.7 Script Configuration............................................................................................... 1-14
1.2.8 Batch File Execution ............................................................................................. 1-17
1.2.9 BAM Database Browse......................................................................................... 1-18
1.3 Notes on Data Configuration ........................................................................................... 1-19
1.3.1 Rules for Setting MML Command Parameters ..................................................... 1-19
1.3.2 Effect of Maximum Number of Tuples on Data Configuration .............................. 1-20
1.3.3 Effect of Software Parameters on Data Configuration.......................................... 1-21
Chapter 2 Configuring Equipment Information.......................................................................... 2-1
2.1 Related Concepts .............................................................................................................. 2-1
2.1.1 Device Numbering................................................................................................... 2-1
2.1.2 Module Numbering.................................................................................................. 2-4
2.1.3 Central Database Function ..................................................................................... 2-4
2.1.4 Protocol Dispatch Ability ......................................................................................... 2-5
2.2 Configuring Equipment Data.............................................................................................. 2-6
2.2.1 Overview ................................................................................................................. 2-6
2.2.2 Adding Shelf............................................................................................................ 2-9
2.2.3 Adding Frame........................................................................................................ 2-10
2.2.4 Adding Board......................................................................................................... 2-10
2.2.5 Adding FE Port Configuration ............................................................................... 2-12
2.2.6 Adding CDB Function............................................................................................ 2-13
2.2.7 Setting Dispatch Ability (Optional)......................................................................... 2-15
2.3 Configuring E1 Port and Clock Data................................................................................ 2-16
2.3.1 Overview ............................................................................................................... 2-16
2.3.2 Adding EPII and CKII Board Data......................................................................... 2-17
24. Operation Manual - Configuration Guide
U-SYS SoftX3000 SoftSwitch System Table of Contents
Huawei Technologies Proprietary
ii
2.3.3 Adding EPII E1 configuration ................................................................................ 2-17
2.3.4 Adding Board Clock Reference Source (Optional) ............................................... 2-18
2.3.5 Setting CKII Clock Configuration........................................................................... 2-19
2.3.6 Setting Clock Reference Source of EPII (Optional) .............................................. 2-20
Chapter 3 Configuring Office Data .............................................................................................. 3-1
3.1 Related Concepts .............................................................................................................. 3-1
3.1.1 Local Office Information .......................................................................................... 3-1
3.1.2 Call Source and DN Set.......................................................................................... 3-1
3.2 Configuring Office Data ..................................................................................................... 3-3
3.2.1 Overview ................................................................................................................. 3-3
3.2.2 Setting Local Office Information.............................................................................. 3-6
3.2.3 Adding Local Office Signaling Point Code (Optional) ........................................... 3-11
3.2.4 Modifying Local Office Assistant Code (Optional)................................................. 3-12
3.2.5 Adding Country or Region Code (Optional) .......................................................... 3-14
3.2.6 Adding National Area Code (Optional).................................................................. 3-14
3.2.7 Adding Toll Prefix Description (Optional) .............................................................. 3-15
3.2.8 Adding Local DN Set............................................................................................. 3-16
3.2.9 Adding Call Source Code...................................................................................... 3-17
3.2.10 Adding Subscriber Number Segment ................................................................. 3-22
3.2.11 Setting Daylight Saving Time (Optional)............................................................. 3-23
Chapter 4 Configuring Charging Data......................................................................................... 4-1
4.1 Related Concepts .............................................................................................................. 4-1
4.1.1 Charging Concepts ................................................................................................. 4-1
4.1.2 Charging Case and Charging Source Code ........................................................... 4-5
4.1.3 Charging Method..................................................................................................... 4-6
4.1.4 Trunk Charging........................................................................................................ 4-9
4.2 Configuring Basic Charging Data ...................................................................................... 4-9
4.2.1 Overview ................................................................................................................. 4-9
4.2.2 Adding Date Category (Optional).......................................................................... 4-12
4.2.3 Modifying Week Category (Optional) .................................................................... 4-13
4.2.4 Adding Charging Case Analysis............................................................................ 4-14
4.2.5 Modifying Charging Mode ..................................................................................... 4-18
4.2.6 Adding Intra-office Group Charging ...................................................................... 4-20
4.2.7 Adding Charging Case Index ................................................................................ 4-21
4.2.8 Adding Called Group Charging ............................................................................. 4-23
4.2.9 Adding Supplementary Service Charging............................................................. 4-24
4.3 Configuring Addition Fee Data......................................................................................... 4-25
4.3.1 Overview ............................................................................................................... 4-25
4.3.2 Adding Additional Fee Charging Mode (Optional) ................................................ 4-26
4.3.3 Modifying Additional Fee Charging Mode............................................................. 4-27
4.4 Configuring CRG Charging Data ..................................................................................... 4-29
4.4.1 Overview ............................................................................................................... 4-29