Micro Electronic Pill Seminar Report

Seminar Report 1
Government Polytechnic College, Neyyattinkara Electronic & Communication
SEMINAR REPORT
ON
MICROELECTRONIC PILL
Done By
SAJAN C K
DIPLOMA IN ELECTRONICS AND COMMUNICATION
DEPARTMENT OF ELECTRONICS AND COMMUNICATION
GOVERNMENT POLYTECHNIC COLLEGE
NEYYATTINKARA
2017

Seminar Report 2
SEMINAR REPORT
ON
MICROELECTRONIC PILL
Done By
SAJAN C K
DIPLOMA IN ELECTRONICS AND COMMUNICATION
NEYYATTINKARA
2017

Seminar Report 3
NEYYATTINKARA
2017
Certificate
This is to certify that this seminar report is a bonafide record of the work done by SAJAN
C K under our guidance towards the partial fulfillment of the requirement for the award
of Diploma in Electronics and Communication Engineering of the Department of
Technical Education, Kerala during the year 2017
Guided By, Sri. Sulficar A
Sri. Aravind Sekhar R HOD
Lecturer Electronics and communication

Seminar Report 4
ACKNOWLEDGEMENT
I take this opportunity to express our sincere gratitude and profound obligation to Sri.
Sulficar A, Head Of Department of Electronics and Communication Engineering, Government
polytechnic College Neyyattinkara.
I also wish to express my gratitude to Sri. Aravind Sekhar R, Sri. Pavitrakumar G, Smt.
Reeya George, Smt. Divya C for their help and encouragement done throughout this work.
Last but not the least, I am extremely grateful to all our friends without whose timely aid,
could not have completed the work successfully.
SAJAN C K
(Reg.no: 14200163)

Seminar Report 5
ABSTRACT
The invention of transistor enabled the first use of radiometry capsules, which used simple
circuits for the internal study of the gastrointestinal (GI) tract. They couldn’t be used as they
could transmit only from a single channel and also due to the size of the components. They also
suffered from poor reliability, low sensitivity and short lifetimes of the devices. This led to the
application of single-channel telemetry capsules for the detection of disease and abnormalities in
the GI tract where restricted area prevented the use of traditional endoscopy.
They were later modified as they had they disadvantage of using laboratory type sensors
such as the glass pH electrodes, resistance thermometers, etc. They were also of very large size.
The later modification is similar to the above instrument but is smaller in size due to the
application of existing semiconductor fabrication technologies. These technologies led to the
formation of “MICROELECTRONIC PILL”.
Microelectronic pill is basically a multichannel sensor used for remote biomedical
measurements using micro technology. This is used for the real-time measurement parameters
such as temperature, pH, conductivity and dissolved oxygen. The sensors are fabricated using
electron beam and photolithographic pattern integration and were controlled by an application
specific integrated circuit (ASIC).

Seminar Report 6
CONTENT
INTRODUCTION………….……………………………………...…......8
MODULE – 1
MICROELECTRONIC PILL DESIGN AND FABRICATION…….…11
1.1 SENSORS ………………………………………………………11
1.2 CONTROL CHIP……………………………………………….16
1.3 RADIO TRANSMITTER ……………………………………...18
1.4 CAPSULE………………………….........................................19
 MODULE – II
INTERNAL VIEW & PILL CAMERA PLATFORM OF CAPSULE..22
2.1 INTERNAL VIEW OF THE CAPSULE……………………....22
2.2 PILL CAMERA PLATFORM COMPONENT………………..24
 MODULE - III
PERFORMANCE OF MICROELECTRONIC PILL..………............29
3.1 TEMPERATURE CHANNEL PERFORMANCE…………….29
3.2 PH CHANNEL PERFORMANCE……………………………31
3.3 OXYGEN SENSOR PERFORMANCE……………………….33
3.4 CONDUCTIVITY SENSOR PERFORMANCE……………...33
3.5 CONTROL CHIP………………………………………………34
3.6 TRANSMISSION FREQUENCY……………………………..34
3.7 DUAL CHANNEL WIRELESS SIGNAL TRANSMISSION..34

Seminar Report 7
 MODULE – IV
ADVANTAGES & DISADVANTAGES……………………………35
4.1 ADVANTAGES………………………………………………..35
4.2 DISADVANTAGES……………………………………………36
4.3 APPLICATIONS……………………………………………….37
4.4 FUTURE SCOPE…………………………………………….....38
 CONCLUSIONS………………………………………….……….40
 REFERENCE………………………………………………...……41

Seminar Report 8
INTRODUCTION
The invention of the transistor enabled the first radiotelemetrycapsules, which utilized
simple circuits forin vivo telemetric studies of the gastro intestinal (GI) tract [1].
These units could only transmit from a single sensor channel, and were difficult to assemble due
to the use of discrete components [2]. The measurement parameters consisted ofeither
temperature, pH or pressure, and the first attemptsof conducting real-time noninvasive
physiological measurementssuffered from poor reliability, low sensitivity, and shortlifetimes of
the devices. The first successful pH gut profiles were achieved in 1972 [3], with subsequent
improvements insensitivity and lifetime. Single-channel radiotelemetrycapsules have since been
applied for the detection of diseaseand abnormalities in the GI tract [4] where restricted
accessprevents the use of traditional endoscopy.
Most radiotelemetry capsules utilize laboratory type sensorssuch as glass pH electrodes,
resistance thermometers, or moving inductive coils as pressure transducers [5]. The
relativelylarge size of these sensors limits the functional complexityof the pill for a given size of
capsule. Adapting existingsemiconductor fabrication technologies to sensor development has
enabled the production of highly functional unitsfor data collection, while the exploitation of
integrated circuitryfor sensor control, signal conditioning, and wireless transmission has
extended the concept of single-channel radiotelemetryto remote distributed sensing from
microelectronicpills.
Our current research on sensor integration and onboard data processing has, therefore,
focused on the development of microsystemscapable of performing simultaneous
multiparameterphysiological analysis. The technology has a range of applicationsin the detection
of disease and abnormalities in medicalresearch. The overall aim has been to deliver enhanced
functionality,reduced size and power consumption, through systemlevelintegration on a common
integrated circuit platform comprising sensors, analog and digital signal processing, and
signaltransmission.

Seminar Report 9
Fig 1.1A Microelectronic pill
In this report, we present a novel analytical microsystemwhich incorporates a four-channel
microsensor array forreal-time determination of temperature, pH, conductivity andoxygen. The
sensors were fabricated using electron beam andphotolithographic pattern integration, and were
controlledby an application specific integrated circuit (ASIC), whichsampled the data with 10-bit
resolution prior to communicationoff chip as a single interleaved data stream. An integrated
radiotransmitter sends the signal to a local receiver (base station),prior to data acquisition on a
computer. Real-time wireless datatransmission is presented from a model in vitro
experimentalsetup, for the first time.Details of the sensors are provided in more detail later,
butincluded: a silicon diode to measure the body core temperature,while also compensating for
temperature induced signal changes in the other sensors; an ion-selective field effect
transistor,ISFET, [6] to measure pH; a pair of direct contact goldelectrodes to measure
conductivity; and a three-electrode electrochemicalcell, to detect the level of dissolved oxygen in
solution.

Seminar Report 10
All of these measurements will, in the future, beused to perform in vivo physiological
analysis of the GI-tract.For example, temperature sensors will not only be used to
measurechanges in the body core temperature, but may also identifylocal changes associated
with tissue inflammation and ulcers.Likewise, the pH sensor may be used for the determination
of the presence of pathological conditions associated withabnormal pH levels, particularly those
associated with pancreaticdisease and hypertension, inflammatory bowel disease, theactivity of
fermenting bacteria, the level of acid excretion, refluxto the oesophagus, and the effect of GI
specific drugs ontarget organs. The conductivity sensor will be used to monitor the contents of
the GI tract by measuring water and salt absorption,bile secretion and the breakdown of organic
componentsinto charged colloids. Finally, the oxygen sensor will measurethe oxygen gradient
from the proximal to the distal GI tract. Thiswill, in future enable a variety of syndromes to be
investigatedincluding the growth of aerobic bacteria or bacterial infectionconcomitant with low
oxygen tension [7], as well as the role ofoxygen in the formation of radicals causing cellular
injury andpathophysiological conditions (inflammation and gastric ulceration).
The implementation of a generic oxygen sensor will alsoenable the development of first
generation enzyme linked amperometricbiosensors, thus greatly extending the range of future
applications to include, e.g., glucose and lactate sensing, as wellas immune-sensing protocols.

Seminar Report 11
MODULE – I
MICROELECTRONIC PILL DESIGN AND FABRICATION
1.1 SENSORS
The sensors were fabricated on two silicon chips located at the front end of the capsule.
Chip 1 [Fig. 1(a), (c), (e)] comprises the silicon diode temperature sensor, the pH ISFET sensor
and a two electrode conductivity sensor. Chip 2 [Fig. 1(b), (d), (f)] comprises the oxygen sensor
and an optional nickel-chromium (NiCr) resistance thermometer. The silicon platform of Chip 1
was based on a research product from Ecole Superieure D’Ingenieurs en Electrotechnique et
Electronique (ESIEE, France) with predefined n-channels in the p-type bulk silicon forming the
basis for the diode and the ISFET. A total of 542 of such devices were batch fabricated onto a
single 4-in wafer. In contrast, Chip 2 was batch fabricated as a 9X9 array on a 380- m-thick
single crystalline 3n silicon wafer with<100> lattice orientation, precoated with 300 nm Si3N4,
silicon nitride, (Edinburgh Microfabrication Facility, U.K.). One wafer yielded 80, 5X5mm2
sensors (the center of the wafer was used for alignment markers).
1.1.1 SENSOR CHIP 1
An array of 4X2 combined temperatureand pH sensor platforms were cut from the wafer
and attachedon to a 100- m-thick glass cover slip using S1818 photoresist(Microposit, U.K.)
cured on a hotplate. The cover slipacted as temporary carrier to assist handling of the device
duringthe first level of lithography (Level 1) when the electric connectiontracks, the electrodes
and the bonding pads were defined.The pattern was defined in S1818 resist by
photolithographyprior to thermal evaporation of 200 nm gold (including an adhesionlayer of 15
nm titanium and 15 nm palladium). An additionallayer of gold (40 nm) was sputtered to improve
the adhesionof the electroplated silver used in the reference electrode. Liftoff in acetone detached

Seminar Report 12
the chip array from thecover slip. Individual sensors were then diced prior to their re-
attachmentin pairs on a 100- m-thick cover slip by epoxy resin.
Fig 2.1-The microelectronic sensors
2.1(a) schematic diagram of Chip 1, measuring 4.75X5 mm2, comprising the pH (ISFET) sensor
(1), the 5X10-4 mm2 dual electrode conductivity sensor (3) and the silicon diode temperature
sensor (4);
2.1(b) schematic diagram of Chip 2, measuring5X5 mm2 , comprising the electrochemical
oxygen sensor (2) and a NiCr resistance thermometer (5). Once integrated in the pill, the area
exposed to the external environment is illustrated by the 3-mm-diameter circle

Seminar Report 13
2.1(c)Photomicrograph of sensor Chip 1
2.1(d) Sensor chip 2. The bonding pads (6), which provide electrical contact to the external
electronic control circuit.
2.1(e) Close up of the pH sensor consisting of the integrated 3X10-2 mm Ag/AgCl reference
electrode (7), a 500-µm-diameter and 50–µm-deep, 10-nL, electrolyte chamber (8) defined in
polyimide, and the 15X600 µm floating gate (9) of the ISFET sensor
2.1(f)The oxygen sensor is likewise embedded in an electrolyte chamber (8). The three-electrode
electrochemical cell comprises the 1X10-1 mm counter electrode (10), a microelectrode array of

Seminar Report 14
57X10 µm diameter (4.5X103 mm2 ) working electrodes (11) defined in 500-nm-thick PECVD
Si3N4 , and an integrated 1.5x10-2 mm Ag/AgCl reference electrode (12).
In Fig. 1(c) the left-hand-side (LHS) unit comprised the diode, while the right-hand-side
(RHS) unit comprised the ISFET. The 15x600 µm (LxW) floating gate of the ISFET was pre-
covered with a 50-nm-thick proton sensitive layer of Si3N4 for pH detection.
Photo curable polyimide (Arch Chemicals, Belgium) defined the 10-nL electrolyte
chamber for the pH sensor (above the gate) and the open reservoir above the conductivity sensor
(Level 2).
The silver chloride reference electrode (3x10-2 mm2) wasfabricated during Levels 3 to 5,
inclusive. The glass cover slip, to which the chips were attached, was cut down to the size ofthe
4.75x5 mm2 footprint (still acting as a supporting base) prior to attachment on a custom-made
chip carrier used for electroplating. Silver (5 µm) was deposited on the gold electrode defined at
by chronopotentiometry (300 nA, 600 s) after removing residual polyimide in an barrel asher
(Electrotech, U.K.) for 2 min. The electroplating solution consisted of 0.2 M, 3MKI and 0.5M.
Changing the electrolyte solution to 0.1 M KCl at Level 4 allowed for the electroplated silver to
be oxidized to AgCl by chronopoteniometry (300 nA, 300 s). The chip was then removed from
the chip carrier prior to injection of the internal 1 M KCl reference electrolyte required for the
Ag AgCl reference electrode (Level 5). The electrolyte was retained in a 0.2% gel matrix of
calcium alginate [8].
The chip was finally clamped by a 1-mm-thick stainless-steel clamp separated by a 0.8- m-
thick sheet of Viton fluoroelastomer (James Walker, U.K.). The rubber sheet provided a uniform
pressure distribution in addition to forming a seal between the sensors and capsule.

Seminar Report 15
1.1.2 SENSOR CHIP 2
The level 1 pattern (electric tracks,bonding pads, and electrodes) was defined in 0.9 m
UV3 resist (Shipley, U.K.) by electron beam lithography. A layer of 200 nm gold (including an
adhesion layer of 15 nm titaniumand 15 nm palladium) was deposited by thermal evaporation.
The fabrication process was repeated (Level 2) to define the 5- m-wide and 11-mm-long
NiCr resistance thermometer made from a 100-nm-thick layer of NiCr (30- resistance). Level 3
defined the 500-nm-thick layer of thermal evaporated silver used to fabricate the reference
electrode. An additional sacrificial layer of titanium (20 nm) protected the silver from oxidation
in subsequent fabrication levels. The surface area of the reference electrode was mm, whereas
the counter electrode made of gold had an area of mm .Level 4 defined the microelectrode array
of the working electrode, comprising 57 circular gold electrodes, each 10 m in diameter, with an
inter-electrode spacing of 25 m and a combined area of 4.5x10-3mm2. Such an array promotes
electrode polarization and reduces response time by enhancing transport to the electrode surface
[9]. The whole wafer was covered with 500 nm plasma-enhanced chemical vapor deposited
(PECVD) Si3N4. The pads, counter, reference, and the microelectrode array of the working
electrode was exposed using an etching mask of S1818 photoresist prior to dry etching with
C2F6. The chips were then diced from the wafer and attached to separate 100- m-thick cover slips
by epoxy resin to assist handling. The electrolyte chamber was defined in 50- m-thick polyimide
at Level 5. Residual polyimide was removed in an O2barrel asher(2 min), prior to removal of the
sacrificial titanium layer at Level 6 in a diluted HF solution (HF to RO water, 1:26) for 15 s. The
short exposure to HF prevented damage to the PECVD layer.
Thermally evaporated silver was oxidized to Ag AgCl (50% of film thickness) by
chronopotentiometry (120 nA, 300 s) atLevel 7 in the presence of KCl, prior to injection of the
internal reference electrolyte at Level 8. A 5.5 mm2 sheet of oxygen permeable teflon was cut out
from a 12.5- m-thick film and attached to the chip at Level 9 with epoxy resin prior to
immobilization by the aid of a stainless steel clamp.

Seminar Report 16
1.2 CONTROL CHIP
The ASIC was a control unit that connected together the external components of the
microsystem (Fig. 2). It was fabricated as a 22.5 mm2 silicon die using a 3-V, 2-poly, 3-metal
0.6- µm.CMOS process by Austria Microsystems (AMS) via the Europractice initiative.
Fig 2.2: Photograph of the 4.75x4.75 mm2application specific integrated Circuit control
chip

Seminar Report 17
2.2(a)The associated explanatory diagram
2.2(b)Schematic of IC control chip of the architecture
2.2(c) Illustrating the interface to external, MUX(four-channel multiplexer), ADC, DAC and
OSC(32-kHz oscillator).
It is a novel mixed signal design that contains an analog signal conditioning module
operating the sensors, a 10-bit analog-to-digital (ADC) and digital-to-analog (DAC) converters,
and a digital data processing module. An RC relaxation oscillator (OSC) provides the clock
signal.
The analog module was based on the AMS OP05B operationalamplifier, which offered a
combination of both a powersavingscheme (sleep mode) and a compact integrated circuit design.
The temperature circuitry biased the diode at constant current, so that a change in temperature
would reflect a corresponding change in the diode voltage. The pH ISFET sensor was biased as a
simple source and drain follower at constant current with the drain-source voltage changing with
the threshold voltage and pH. The conductivity circuit operated at direct current measuring the
resistance across the electrode pair as an inverse function of solution conductivity. An
incorporated potentiostatcircuit operated the amperometric oxygen sensor with a 10-bit DAC
controlling the working electrode potential with respect to the reference. The analog signals had
a full-scale dynamic range of 2.8 V (with respect to a 3.1-V supply rail) with the resolution
determined by the ADC. The analog signals were sequenced through a multiplexer prior to being
digitized by the ADC. The bandwidth for each channel was limited by the sampling interval of
0.2 ms.
The digital data processing module conditioned the digitized signals through the use of a
serial bitstream data compression algorithm, which decided when transmission was required by
comparing the most recent sample with the previous sampled data. This technique minimizes the

Seminar Report 18
transmission length, and is particularly effective when the measuring environment is at
quiescent, a condition encountered in many applications [10].
The entire design was constructed with a focus on low powerconsumption and immunity
from noise interference. The digital module was deliberately clocked at 32 kHz and employed a
sleep mode to conserve power from the analog module. Separate on-chip power supply trees and
pad-ring segments were used for the analog and digital electronics sections in order to discourage
noise propagation and interference.
1.3 RADIO TRANSMITTER
The radio transmitterwas assembled prior to integration in the capsule using discrete
surface mount components on a singlesided printed circuit board (PCB). The footprint of the
standard transmitter measured 8x5x3 mm including the integrated coil (magnetic) antenna. It was
designed to operate at a transmission frequency of 40.01 MHz at 20 C generating a signal of 10
kHz bandwidth. A second crystal stabilized transmitter was also used. This second unit was
similar to the free running standard transmitter, apart from having a larger footprint of 10x5x3
mm, and a transmission frequency limited to 20.08 MHz at 20 C, due to the crystal used. Pills
incorporating the standard transmitter were denoted Type I, whereas the pills incorporating the
crystal stabilized unit were denoted Type II. The transmission range was measured as being 1
meter and the modulation scheme frequency shift keying (FSK), with a data rate of 1 kbs-1.

Seminar Report 19
1.4 CAPSULE
The microelectronic pill consisted of a machined biocompatible (noncytotoxic), chemically
resistant polyether-terketone (PEEK) capsule (Victrex, U.K.) and a PCB chip carrier acting as a
common platform for attachment of the sensors, ASIC, transmitter and the batteries. The
fabricated sensors were each attached by wire bonding to a custom made chip carriermade from a
10-pin, 0.5-mm pitch polyimide ribbon connector.
The ribbon connector was, in turn, connected to an industrial standard 10-pin flat cable
plug (FCP) socket (Radio Spares, U.K.) attached to the PCB chip carrier of the microelectronic
pill, to facilitate rapid replacement of the sensors when required. The PCB chip carrier was made
from two standard 1.6-mm-thick fiber glass boards attached back to back by epoxy resin which
maximized the distance between the two sensor chips. The sensor chips were connected to both
sides of the PCB by separate FCP sockets, with sensor Chip 1 facing the top face, with Chip 2
facing down. Thus, the oxygen sensor on Chip 2 had to be connected to the top face by three
200- m copper leads soldered on to the board. The transmitter was integrated in the PCB which
also incorporated the power supply rails, the connection points to the sensors, as well as the
transmitter and the ASIC and the supporting slots for the capsule in which the chip carrier was
located.
The ASIC was attached with double-sided copper conductingtape (Agar Scientific, U.K.) prior to
wire-bonding to the powersupply rails, the sensor inputs, and the transmitter (a process which
entailed the connection of 64 bonding pads). The unit was powered by two standard 1.55-V
SR44 silver oxide cells with a capacity of 175 mAh. The batteries were serial connected and
attached to a custom made 3-pin, 1.27-mm pitch plugby electrical conducting epoxy
(Chemtronics, Kennesaw, GA).
The connection to the matching socket on the PCB carrier provided a three point power
supply to the circuit comprising a negative supply rail ( 1.55 V), virtual ground (0 V), and a
positive supply rail (1.55 V). The battery packwas easily replaced during the experimental
procedures.

Seminar Report 20
Fig2.3Schematic diagram (top) of the remote mobile analytical microsystem comprising the
electronic pill.

Seminar Report 21
In the figure, the prototype is 16x55 mm, weights 13.5 g.The Type I unit consist of the
microelectronic sensors at the front enclosed by the metal clamp and rubber seal (1) which
provide a 3-mm-diameter access channel to the sensors (2). The front section of the capsule,
physically machinedfrom solid PEEK, is illustrated (3) with the rear section removed to
illustratethe internal design. The front and rear section of the capsule is joined by a screw
connection sealed off by a Viton-rubber O-ring (4). The ASIC control chip (5) is integrated on
the common PCB chip carrier (6) which incorporates the discrete component radio transmitter
(7), and the silver oxide battery cells (8).
The battery is connected on the reverse side of the PCB (9). The Type II unit is identical to
the Type I with exception of an incorporated crystal stabilized radio transmitter (10) for
improved temperature stability.
The capsule was machined as two separate screw-fitting compartments.The PCB chip
carrier was attached to the front sectionof the capsule (Fig. 3). The sensor chips were exposed to
the ambient environment through access ports and were sealed by two sets of stainless steel
clamps incorporating a 0.8-m thick sheet of Viton fluoroelastomer seal. A 3-mm-diameter access
channel in the center of each of the steel clamps (incl. the seal), exposed the sensing regions of
the chips. The rear section of the capsule was attached to the front section by a 13-mm screw
connection incorporating a Viton rubber O-ring (James Walker, U.K.). The seals rendered the
capsule water proof, as well as making it easy to maintain (e.g., during sensor and
batteryreplacement). The complete prototype was 16x55 mm and weighted 13.5 g including the
batteries. A smaller pill suitable for physiological in vivo trials (10x30 mm) is currently being
developed from the prototype.

Seminar Report 22
MODULE – II
INTERNAL VIEW & PILL CAMERA PLATFORM OF CAPSULE
2.1 INTERNALVIEW OF THE CAPSULE
The figure shows the internal view of the pill camera. It has 8 parts:

Seminar Report 23
1. Optical Dome.
2. Lens Holder.
3. Lens.
4. Illuminating LEDs.
5. CMOS Image Sensor.
6. Battery.
7. ASIC Transmitter.
8. Antenna.
 OPTICAL DOME
It is the front part of the capsule and it is bullet shaped. Optical dome is the light
receiving window of the capsule and it is a non- conductor material. It prevent the filtration of
digestive fluids inside the capsule.
 LENS HOLDER
This accommodates the lens. Lenses are tightly fixed in the capsule to avoid dislocation
of lens.
 LENS
It is the integral component of pill camera. This lens is placed behind the Optical Dome.
The light through window falls on the lens.
 ILLUMINATING LEDs
Illuminating LEDs illuminate an object. Non reflection coating id placed on the light
receiving window to pr event the reflection. Light irradiated from the LED s pass through the
light receiving window.

Seminar Report 24
 CMOS IMAGE SENSOR
It have 140 degree field of view and detect object as small as 0.1mm. Ithave high precise.
 BATTERY
Battery used in the pill camera is bullet shaped and two in number and silver oxide
primary batteries are used. It is disposable and harmless material.
 ASIC TRANSMITTER
It is application specific integrated circuit and is placed behind the batteries. Two
transmitting electrodes are connected to this transmitter and these electrodes are electrically
isolated
 ANTENNA
Parylene coated on to polyethylene or polypropylene antennas are used. Antenna received
data from transmitter and then send to data recorder.
2.2 PILL CAMERA PLATFORM COMPONENTS
In order for the images obtained and transmitted by the capsule endoscope to be useful,
they must be received and recorded for study. Patients undergoing capsule endoscopy bear an
antenna array consisting of leads that are connected by wires to the recording unit, worn in
standard locations over the abdomen, as dictated by a template for lead placement.The antenna
array is very similar in concept and practice to the multiple leads that must be affixed to the chest
of patients undergoing standard lead electrocardiography. The antenna array and battery pack
cam be worn under regular clothing. The recording device to which the leads are attached is
capable of recording the thousands of images transmitted by the capsule and received by the

Seminar Report 25
antenna array. Ambulary (non-vigorous) patient movement does not interfere with image
acquisition and recording. A typical capsule endoscopy examination takes approximately 7
hours.
Mainly there are 5 platform components:
i. Pill cam Capsule -SB or ESO.
ii. Sensor Array Belt.
iii. Data Recorder.
iv. Real Time Viewer.
v. Work Station and Rapid Software.
 PILL CAM CAPSULE
SB ESO
Approved by Food and Drug
Administration.
Approved b y Food and Drug
Administration.
For small bowel. For esophagus.
Standard lighting control. Automatic Lighting Control
One side imaging.
Two sided imaging.
Two images per second.
14 Images per Second
50,000 images in 8 hours. 2,600 images in 20 minutes.

Seminar Report 26
Several wires are attached to the abdomen like ECG leads to obtain images by radio
frequency. These wires are connected to a light weight data recorder worn on a belt. Sensor
arrays are used to calculate and indicate the position of capsule in the body. A patient receiver
belt around his or her waist over clothing. A belt is applied around the waist and holds a
recording device and a batter y pack. Sensors are incorporated within the belt. Parts of sensor
array are sensor pads, data cable, battery charging, and receiver bag.
To remove the Sensor Array from your abdomen, do not pull the leads off the Sensor Arr
ay! Peel off each adhesive sleeve starting with the non adhesive tab without removing the sensor
from the adhesive sleeve. Place the Sensor Array with the rest of the equipment.
 DATA RECORDER
Data recorder is a small portable recording device placed in the recorder pouch,
attached to the sensor belt. It has light weight (470 gm). Data recorder receives and records
signals transmitted by the camera to an array of sensors placed on the patients body. It is of the
size of walkman and it receives and stores 5000 to 6000 JPEG images on a 9 GB hard drive.
Images takes several hours to download through several connection.
The Date Recorder stores the images of your examination. Handle the Date Recorder,
Recorder Belt, Sensor Array and Battery Pack carefully. Do not expose them to shock, vibration
or direct sunlight, which may result in loss of infor mation. Return all of the equipment as soon
as possible.

Seminar Report 27
 REAL TIME VIEWER
It is a handheld device and it enables real-time viewing. It contains rapid reader
software and colour LCD monitor. It test the proper functioning before procedures and
confirms location of capsule.
 WORKSTATION AND RAPID SOFTWARE
Rapid workstation per forms the function of reporting and processing of images and data.
I mage data from the data recorder is downloaded to a computer equipped with software called
rapid application software. I t helps to convert images in to a movie and allows the doctor to
view the colour 3D images.
Once the patient has completed the endoscopy examination, the antenna array and image
recording device are returned to the health care provider. The recording device is then attached to
a specially modified computer wor kstation, and the entire examination is downloaded in to the
computer, where it becomes available to the physician as a digital video. The workstation
software allows the viewer to watch the video at varying rates of speed, to view it in both

Seminar Report 28
forward and rever se directions, and to capture and label individual frames as well as br ief video
clips. I mages showing normal anatomy of pathologic findings can be closely examined in full
colour.
A recent addition to the software package is a feature that allows some degree of
localisation of the capsule within the abdomen and correlation to the video images. Another new
addition to the software package automatically highlights capsule images that correlates with the
existence of suspected blood or red areas.
Review and analysis using Microview and workstation

Seminar Report 29
MODULE – III
PERFORMANCE OF MICROELECTRONIC PILL
The power consumption of the microelectronic pill with the transmitter, ASIC and the
sensors connected was calculated to 12.1 mW, corresponding to the measured current
consumption of 3.9 mA at 3.1-V supply voltage. The ASIC and sensors consumed 5.3 mW,
corresponding to 1.7 mA of current, whereas the free running radio transmitter (Type I)
consumed 6.8 mW (corresponding to 2.2 mA of current) with the crystal stabilized unit (Type II)
consuming 2.1 mA. Two SR44 batteries used provided an operating time of more than 40 h for
the microsystem.
3.1 TEMPERATURE CHANNEL PERFORMANCE
The linear sensitivity was measured over a temperature range from 0 C to 70 C and found
to be 15.4 mVºC-1. This amplified signal response was from the analog circuit, which was later
implemented in the ASIC. The sensor [Fig. 4(a)], once integrated in the pill, gave a linear
regression of 11.9 bitsºC-1(f(T0c) = 11.9(T0C) – 42.7, R2 = 0.99), with a resolution limited by the
noise band of 0.4ºC [Fig. 4(b)]. The diode was forward biased with a constant current (15 A)
with the n-channel clamped to ground, while the p-channel was floating.
Since the bias current supply circuit was clamped to the negative voltage rail, any change
in the supply voltage potential would cause the temperature channel to drift. Thus, bench test
measurementsconducted on the temperature sensor revealed thatthe output signal changed by
1.45 mV per mV change in supply voltage ( f(mV) = -1.45 (mV) + 2584, R2 = 0.99) with f(mV)
expressed in millivolts, corresponding to a drift of -21 mVh-1 in the pill from a supply voltage
change of -14.5 mVh-1 .

Seminar Report 30
Fig 4.1 Temperature sensor
4.1(a). Temperature recording over a range from 9.1 C to 47.9 C, represented by digital data
points
4.1(b). High-resolution plot ofa temperature change from 49.8ºC to 48.7ºC

Seminar Report 31
3.2 pH CHANNEL PERFORMANCE
The linear characteristics from pH 1 to 13 corresponded to a sensitivity of -41.7mV pH-1
unit at 23ºC, which is in agreement with literature values [6] although the response was lower
than the Nernstian characteristics found in standard glass pH electrodes (-59.2 mV pH-1 unit).
The pH ISFET sensor operated in a constant current mode (15 µA), with the drain voltage
clamped to the positive supply rail, and the source voltage floating with the gate potential. The
Ag AgCl reference electrode, representing the potential in which the floating gate was referred
to, was connected to ground. The sensor performance, once integrated in the pill [Fig. 5(a)],
corresponded to 14.85 bits pH-1 which gave a resolution of 0.07 pH per datapoint. The calibrated
response from the pH sensor conformed to a linear regression (f(pH) = -14.85(pH) + 588, R2 =
0.98), although the sensor exhibited a larger responsivityin alkaline solutions. The sensor lifetime
of 20 h was limited by the Ag/AgCl reference electrode made from electroplated silver. The pH
sensor exhibited a signal drift of -6 mV h-1.(0.14 pH), of which -2.5 mV h-1 was estimated to be
due to the dissolution of AgCl from the reference electrode. The temperature sensitivity of the
pH-sensor was measured as 16.8 mVºC-1 . Changing the pH of the solution at 40ºC from pH 6.8
to pH 2.3 and pH 11.6 demonstrated that the two channels were completely independent of each
other and that there was no signal interference from the temperature channel [Fig. 4.2(b)].

Seminar Report 32
Fig 4.2 pH SENSOR
4.2(a) pH recording in the range of pH 2 to 13, represented by digital datapoints
4.2(b) dynamic recording of temperature (1) and pH (2) usinga direct communication link

Seminar Report 33
3.3 OXYGEN SENSOR PERFORMANCE
The electrodes were first characterized using the model redox compound FMCA, showing
that the oxygen sensor behaved with classic microelectrode characteristics [9]. The reduction
potential of water was subsequently measured at 800 mV (Versus the integrated Ag AgCl) by
recording the steady-state current in oxygen-depleted PBS, thereby excluding any interfering
species. In order to calibrate the sensor, a three point calibration was performed (at saturated
oxygen, and with oxygen removed by the injection of Na2S2O3 to a final concentration of 1 M).
The steady state signal from the oxygen saturated solution was recorded at a constant
working electrode potential of -700 mV (versus Ag AgCl), which was below the reduction
potential for water. This generated a full-scale signal of 65 nA corresponding 8.2 mg O2 L-1 . The
injection Na2S2O3 of into the PBS after 90 s provided the zero point calibration. This fall in the
reduction current provided corroborative evidence that dissolved oxygen was being recorded, by
returning the signal back to the baseline level once all available oxygen was consumed. A third,
intermediate point was generated through the addition of 0.01M Na2S2O3. The resulting
calibration graph conformed to a linear regression (f(MgO2) = 7.9(MgO2), R2 = 0.99) with
expressed in nanoamperes. The sensitivity of the sensor was 7.9 nA mg-1 O2, with the resolution
of 0.4 mg L-1 limited by noise or background drift. The lifetime of the integrated Ag/AgCl
reference electrode, madefrom thermal evaporated silver, was found to be to 45 h, with
anaverage voltage drift of -1.3 mV h-1 due to the dissolution ofthe AgCl during operation. Both
measurements of FMCA and oxygen redox behavior indicated a stable Ag AgCl reference.
3.4 CONDUCTIVITY SENSOR PERFORMANCE
The prototype circuit exhibited a logarithmic performance from 0.05 to 10 mS/cm which
conformed to a first-order regression analysis (f(mS/cm)= 165 ln (mS/cm) + 850), R2=0.99) with
f(mS/cm) expressed in millivolts. The sensor saturated at conductivities above 10 mS/cm due to
the capacitive effect of the electric double layer, a phenomena commonly observed in
conductimetric sensor systems [12].

Seminar Report 34
3.5 CONTROL CHIP
The background noise from the ASIC corresponded to a constantlevel of 3-mV peak-to-
peak, which is equivalent to oneleast significant bit (LSB) of the ADC. Since the second LSB
were required to provide an adequate noise margin, the 10-bit ADC was anticipated to have an
effective resolution of 8 bits.
3.6 TRANSMISSION FREQUENCY
Frequency stabilized units were essential to prevent the transmission drifting out of range,
particularly if the pill was subjectto a temperature change during operation. The standard Type I
transmitter exhibited a negative linear frequency change from 39.17 MHz at 1 C to 38.98 MHz at
49 C. The transmitter’s signal magnitude was not affected with the pill immersed in the different
electrolyte solutions or RO water, compared to the pill surrounded by air only. Tests were also
conducted with the pill immersed in the large polypropylene beaker filled with 2000 mL of PBS
without the signal quality being compromised. The electromagnetic noise baseline was measured
to 78 dB of S/N in the 20 MHz band of the crystal stabilized transmitter.
3.7 DUAL CHANNEL WIRELESS SIGNAL TRANSMISSION
Dual channel wireless signal transmission was recorded fromboth the pH and temperature
channels at 23ºC, with the pill immersed in a PBS solution of changing pH. The signal from the
pH channel exhibited an initial offset of 0.2 pH above the real value at pH 7.3. In practice, the
pH sensor was found to exhibit a positive pH offset as the solution became more acidic, and a
negative pH offset as the solution became more alkaline. The response time of the pH sensor was
measured to 10 s. The temperature channel was unaffected by the pH change, confirming the
absence of crosstalk between the two channels in Fig. 4.2(b).

Seminar Report 35
MODULE – IV
ADVANTAGES & DISADVANTAGES
4.1 ADVANTAGES
 It is being beneficially used for disease detection & abnormalities in human body.
Therefore it is also called as MAGIC PILL OFR HEALTH CARE.
 Painless, no side effects.
 Accurate, precise (view of 150 degree).
 High quality images.
 Harmless material.
 Simple procedure.
 High sensitivity and specificity.
 Avoids risk in sedation.
 Efficient than X-ray CT-scan, normal endoscopy.
 Micro Electronic Pill utilizes a PROGRAMMABLE STANDBY MODE; So power
consumption is very less.
 It has very small size; hence it is very easy for practical usage.
 Very long life of the cells (40 hours), Less Power, Current & Voltage requirement (12.1
mW, 3.9 mA, 3.1 V).
 Less transmission length & hence has zero noise interference.

Seminar Report 36
4.2 DISADVANTAGES
 Gastrointestinal obstructions prevent the free flow of capsule.
 Patients with pacemakers, pregnant women face difficulties.
 It is very expensive and not reusable.
 Capsule endoscopy does not replace standard diagnostic endoscopy.
 It is not a replacement for any existing GI imaging technique, generally
performed after a standard endoscopy and colonoscopy.
 It cannot be controlled once it has been ingested, cannot be stopped or steered to
collect close-up details.
 It cannot be used to take biopsies, apply therapy or mark abnormalities for surgery.
 It cannot perform ultrasound & impedance tomography. Tomography is imaging by
sections or sectioning, through the use of any kind of penetrating wave.
 Cannot detection abnormalities.
 Cannot perform radiation treatment associated with cancer & chronic inflammation.
 Micro Electronic Pill are expensive & are not available in many countries.
 Still its size is not digestible to small babies.

Seminar Report 37
4.3APPLICATIONS
 It is used to detect ulcers
 Biggest impact in the medical industry.
 Nano robots perform delicate surgeries.
 Pill cam ESO can detect esophageal diseases, gastrointestinal reflex diseases,
barreff’s esophagus.
 It is used to diagnose Malabsorption
 Pill cam SB can detect Crohn’s disease, small bowel tumours, small
bowel injury, celiac disease, ulcerative colitis etc.

Seminar Report 38
4.4 FUTURE SCOPE
It seems likely that capsule endoscopy will become increasingly effective in diagnostic
gastrointestinal endoscopy. This will be attractive to patients especially for cancer or varices
detection because capsule endoscopy is painless and is likely to have a higher take up rate
compared to conventional colonoscopy and gastroscopy. Double imager capsules with increased
frame rates have been used to image the esophagus for Barrett’s and esophageal varices. The
image quality is not bad but needs to be improved if it is to become a realistic substitute for
flexible upper and lower gastrointestinal endoscopy. An increase in the framerate, angle of view,
depth of field, image numbers, duration of the procedure and improvements in illumination seem
likely. Colonic, esophageal and gastric capsules will improve in quality, eroding the supremacy
of flexible endoscopy, and become embedded into screening programs. Therapeutic capsules will
emerge with brushing, cytology, fluid aspiration, biopsy and drug deliver y capabilities.
Electrocautery may also become possible. Diagnostic capsules will integrate
physiological measurements with imaging and optical biopsy, and immunologic cancer
recognition. Remote control movement will improve with the use of magnets and/or electro
stimulation and perhaps electromechanical methods. External wireless commands will influence
capsule diagnosis and therapy and will increasingly entail the use of real-time imaging. However,
it should be noted that speculations about the future of technology in any detail are almost
always wrong.
The development of the capsule endoscopy was made possible by miniaturization of
digital chip camera technology, especially CMOS chip technology. The continued reduction in
size, increases in pixel numbers and improvements in imaging with the two rival technologies-
CCD and CMOS is likely to change the nature of endoscopy. The current differences ar e
becoming blurred and hybrids are emerging.The main pr essure is to reduce the component size,
which will release space that could be used for other capsule functions such as biopsy,
coagulation or therapy. New engineering methods for constructing tiny moving parts, miniature
actuators and even motors into capsule endoscopes are being developed.

Seminar Report 39
Although semiconductor lasers that are small enough to swallow are available, the nature of lasers which
have typical inefficiencies of 100-1000 per cent makes the idea of a remote laser in a capsule capable of
stopping bleeding or cutting out a tumour seems to be something of a pipe dream at present, because of
power requirements
The construction of an electrosurgical generator small enough to swallow and powered
by small batteries is conceivable but currently difficult because of the limitations imposed by the
internal resistance of the batteries. It may be possible to store power in small capacitors for
endosurgical use, and the size to capacity ratio of some capacitor s has recently been reduced by
the use of tantalum. Small motors are currently available to move components such as biopsy
devices but need radio- controlled activators.
One limitation to therapeutic capsule endoscopy is the low mass of the capsule endoscope
(3.7 g). A force exerted on tissue for example by biopsy forceps may push the capsule away from
the tissue. Opening small biopsy forceps to grasp tissue and pull it free will require different
solutions to those used at flexible endoscopy-the push force exerted during conventional biopsy
is typically about 100 g and the force to pull tissue free is about 400 g.
Future diagnostic developments are likely to include capsule gastroscopy, attachment to
the gut wall, ultrasound imaging, biopsy and cytology, propulsion methods and therapy including
tissue coagulation. Narrow band imaging and immunologically or chemically targeted optical
recognition of malignancy are currently being explored by two different groups supported by the
European Union as FP6 projects: -the VECTOR and NEMO projects. These acronyms stand for:
VECTOR = Versatile Endoscopic Capsule for gastrointestinal Tumour Recognition and therapy
and NEMO = Nano-based capsule-Endoscopy with Molecular Imaging and Optical biopsy.
The reason because of doctors rely more on camera pill than other types of endoscope is
because the former has the ability of taking pictures of small intestine which is not possible from
the other types of tests.

Seminar Report 40
CONCLUSION
Wireless capsule endoscopy represents a significant technical breakthrough for the
investigation of the small bowel, especially in light of the shortcomings of other available
techniques to image this region. Capsule endoscopy has the potential for use in a wide range of
patients with a variety of illnesses. At present, capsule endoscopy seems best suited to patients
with gastrointestinal bleeding of unclear etiology who have had non-diagnostic traditional testing
and whom the distal small bowel(beyond reach of a push enetroscope) needs to be visualised.
The ability of the capsule to detect small lesions that could cause recurrent bleeding(eg.
tumours, ulcers) seems ideally suited for this particular role. Although a wide variety of
indications for capsule endoscopy are being investigated, other uses for the device should be
considered experimental at this time and should be performed in the context of clinical trials.
Care must be taken in patient selection, and the images obtained must be interpreted
approximately and not over read that is, not all abnormal findings encountered are the source of
patient’s problem. Still, in the proper context, capsule endoscopy can provide valuable
information and assist in the management of patients with difficult –to- diagnose small bowel
disease.
In this study capsule endoscopy was superior to push enteroscopy in the diagnosis of
recurrent bleeding in patients who had a negative gastroscopy and colonoscopy. It was safe and
well tolerated Wireless capsule endoscopy represents a significant technical breakthrough
for the investigation of the small bowel, especially in light of the shortcomings of other available
techniques to image this region. The capsule endoscopy seems best suited to patients with
gastrointestinal bleeding of unclearetiology who have had nondiagnostic traditional testing and in
whom the distal small bowel(beyond reach of a push enteroscope) needs to be visualized

Seminar Report 41
REFERENCES
[1] S. Mackay and B. Jacobson, “Endoradiosonde,” Nature, vol. 179, pp. 1239–1240, 1957.
[2] H. S.Wolff, “The radio pill,” New Scientist, vol. 12, pp. 419–421, 1961.
[3] S. J. Meldrum, B. W. Watson, H. C. Riddle, R. L. Bown, and G. E. Sladen, “pH profile of gut
as measured by radiotelemetry capsule,” Br. Med. J., vol. 2, pp. 104–106, 1972.
[4] S. S. Kadirkamanathan, E.Yazaki, D. F. Evans, C. C. Hepworth, F. Gong, and C. P. Swain,
“An ambulant porcine model of acid reflux used to evaluate endoscopic gastroplasty,” Gut, vol.
44, no. 6, pp. 782–788, June 1999.
[5] S. Mackay, “Radio telemetering from within the body,” Science, vol. 134, pp. 1196–1202,
1961.
[6] C. Cane, I. Gracia, and A. Merlos, “Microtechnologies for pH ISFET chemical sensors,”
Microelectr. J., vol. 28, no. 4, pp. 389–405, May 1997.
[7] L. E. Bermudez, M. Petrofsky, and J. Goodman, “Exposure to low oxygen tension and
increased osmolarity enhance the ability of Myobacteriumavium to enter intertestinal epithelial
(HT-29) cells,” Infect. Immun., vol. 65, no. 9, pp. 3768–3773, Sep. 1997.
[8] H. Suzuki, N. Kojima, A. Sugama, F. Takei, and K. Ikegami, “Disposable oxygen electrodes
fabricated by semiconductor techniques and their applications to biosensors,” Sens. Actuators B,
vol. 1, no. 1–6, pp. 528–532, Jan. 1990.
[9] M. E. Sandison, N. Anicet, A. Glidle, and J. M. Cooper, “Optimization of the geometry and
porosity of microelectrode arrays for sensor design,” Anal. Chem., vol. 74, no. 22, pp. 5717–
5725, Oct. 2002.
[10] L.Wang, T. B. Tang, E. A. Johannessen, A. Astaras, A. F. Murray, J. M. Cooper, S. P.
Beaumont, and D. R. S. Cumming, “An integrated sensor microsystem for industrial and
biomedical applications,” in Proc. IEEE Instrumentation Measurement Technology Conf., vol. 2,
Anchorage, AK, 2002, pp. 1717–1720.
[11] R. M. C. Dawson, D. C. Elliott, W. H. Elliott, and K. M. Jones, Data for Biochemical
Research, 3rd ed. Oxford, U.K.: Clarendon, 1986, pp. 1–580.
[12] H. Morgan and N. Green, AC Electrokinesis: Colloids and Nanoparticles. Baldock, U.K.:
Research Studies Press Ltd, 2003, pp. 1–324.

Micro Electronic Pill Seminar Report

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Was ist angesagt?

Was ist angesagt? (20)

Ähnlich wie Micro Electronic Pill Seminar Report

Ähnlich wie Micro Electronic Pill Seminar Report (20)

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

Micro Electronic Pill Seminar Report