2. STERN TUBE
A stern tube is a hollow tube that runs through
the bottom of the ship from the main engine to
the propeller. The ship’s tail shaft or propeller
shaft, which transfers power from the main
engine, runs inside the stern tube and connects
to the propeller.
In addition, the stern tube is the only piece that
connects propellers to the ship. Propellers can
weigh thousands of pounds, meaning a stern
tube needs to be sturdy enough to support the
propeller’s weight. So, it is designed and
manufactured with enough precision to keep
water from leaking into the ship’s stern.
3. The stern tube of a ship has a peculiar shape and arrangement
for carrying the propeller shaft. As the shape of the ship is
streamlined at the aft end, there is very little space to
accommodate the propeller shaft arrangement. The stern tube is
situated at the aft peak of the ship’s hull and the propeller shaft
arrangement is also situated at the same level. The forward end
of the stern tube is supported by the aft peak bulk head and the
aft end of the stern tube gets its support from the stern frame of
the ship. Throughout the length, the shaft is supported by
specially designed brackets and narrow floors inside the stern
tube.
3
5. Water Lubricated Stern tubes
The stern tube is normally constructed of cast iron slightly larger at the
forward end to ease removal. The forward end is flanged and bolted to a
doubler-plate stiffened aft peak bulkhead. The forward end is supplied with
a stuffing box and gland, the after end with a bearing comprising lignum
vitae staves or similar, and is dove tailed into a brass bush. The wood is
machined and cut on end grain. i.e. The staves in the lower bearing area
are cut and fitted in such away that the end grain is vertical to facilitate
better life and staves at the top part are cut with grain in the axial direction
for economy. The bearing can be lined with Lignum Vitae , rubber
composition (cutlass rubber) or an approved plastic material (Certain
plastics possess good bearing properties being inert and very tolerant of
slow speed boundary lubrication conditions. Cresylic resin bonded
asbestos such as Railco WA80H give good results in condition of heavy
water contamination in the lubricating oil of almost 100%).
For water lubricated bearing not less than 4 x the diameter of the steel
shaft. If the bearing is over 380mm diameter forced water lubrication must
be used, a circulating pump or other source with a water flow indicator.
The shaft is withdrawn for examination every 3 years.
5
8. Bearing placement on a stern tube:
To function properly, a ship’s tail shaft must be lubricated.
Typically, ships have lubricating systems consisting of
header tanks positioned between six to nine feet above the
water line to create pressure that allows the lubricant to
flow into the tube.
Because lubrication is so vital to a ship’s ability to generate
thrust, it’s important that nothing reduces its effectiveness.
Naturally, water is thinner than the lubricant, so sealing the
connection between the stern tube and the propeller is
essential. This is accomplished by using stern tube
bearings.
8
10. Stern tube bearings serve two main functions:
1. To properly connect the propeller to the ship
2. To keep water from leaking into the stern tube (and lubricant
from leaking out)
There are three types of stern tube bearing arrangements
that are used to accomplish these goals:
1. Stuffing boxes, which uses packing material to seal the area
2. Lip seals, which are connected to the tail shaft to prevent
lubricant or water from passing through the shaft
3. Radial face seals, which are supported with specially fitted
springs around the shaft, aft bulkheads and near the back end
of the stern tube
10
11. Modern Water tolerant oil lubricated stern Tube:
With the increase in size of VLCC's shipping companies required a
stern tube bearing capable of operating with high degrees of water
contamination. The alloys in white metal tend to oxidize and the
clearance is removed leading to seizure. In addition as shaft revs
reduced in search of improved propeller efficiency the hydrodynamic
forces available become limited for oil film generation.
For this reason Railco WA80H bearings where developed. These
contained a phenolic resin impregnated asbestos yarn. The next
generation contained non-asbestos material. This material tended to be
tainted due a series of overheating problems. (later found due to the
combination of stiff high power transfer shafts and flexible hull design).
The modern material is called Stern Safe and comprises an inner
bearing surface with an over wound outer layer. This has greater
tolerance to overheating and reduced swell in the event of water
contamination. The latter allows for reduced running clearance and
thereby greater control of the shaft position reducing oil loss, seal
damage and water ingress.
A wear gauge is incorporated into the bearing as our temperature
sensors. 11
12. Oil lubricated Bearings
Unlike for the water lubricated stern tube a shaft liner is unnecessary.
Generally a small one is fitted in way of the aft seal bolted on to the
propeller boss. In this way it excludes sea water contact with the main
shaft and provides an easily replaceable rubbing surface for the seal.
Lined with white metal are to have a bearing length so as not to exceed a
bearing pressure from the weight of the shaft and propeller of 5 kg/cm2.
The limitations of a bearing are the load it can withstand without metal
cracking or squeezing out and the temperature it can withstand without
melting. Length of bearing not less than 2 X D in any case. Cast iron and
bronze bearings must have a bearing length not less than 4D. Lubrication
system must be capable of maintaining oil tightness despite varying
temperature. Gravity tanks fitted with low level alarms, Usual for aft peak to
be filled with water to provide cooling low suction valve to be fitted to be
locked shut.
Wear down for the white metal should not exceed 2mm to avoid
hammering out and the period for inspection is 6 years. A highly resilient
reinforced plastic may be used in place of the white metal. It is claimed to
have greater load carrying capacity, high resistance to fatigue and shock
loading, with good lubrication properties. Ceramic liners can also be used.12
14. This system depends upon Hydrostatic lubrication stern
tube oil charge remaining in stern tube until pressure test is
carried put to ensure that oil supply line is not blocked. This
is done by manipulation of valves at header tank and
operation of pump which slightly over pressurises stern
tube. Oil returning to tank indicating clear oil lines. Top half
of white metal bearing is usually machined to give a left
hand and right hand helix, this gives a small pumping
pressure forward to aft to provide lubrication and to assist
in maintaining oil tightness of the oil seals.
14
15. Oil lubricated bearings
If outboard seal leaks, the following steps are to be taken:
1. Fresh water in gravity tank to emulsify and coagulate it,
oil pumped around system to seal and lubricated.
2. Recharge with high viscosity oil
3. Disconnect oil supply line and reconnect to 45 gallon
drum which is supported by block and tackle in order to
give a variable head. By raising and lowering the drum
the oil pressure in the system can be made to match the
water pressure from outside (taking into account the
difference in gravities.
15
16. When large propellers are fitted the heavy overhanging weight
greatly increases the load at the after end of the stern tube
breaking down the hydrostatic lubrication causing metal to metal
contact and seizure towards the aft end of bearing. To obviate
this it is usual to angle the shaft downwards for about 8mm over
100m length thus attempting to ensure than the weight of the
bearing is taken on the full length of the bearing. It is good
practice to leave the oil tank open to the stern tube when in port
with machinery stopped, this prevents sea water leaking into the
system. However, water has been known to contaminate
lubricating oil systems causing rusting of tail shaft particularly
when shaft is stopped for periods long enough for water to settle
in bottom of bearing. Fit only water separator i,e, a coalescer or
cyclonic or osmosis system.
In ships with large changes in draught it is usual to fit two gravity
tanks. The upper tank is used when fully loaded or there is water
leaking in. 16
17. Water based oil replacements:
Available are water based stern tube lubricants having the
advantages of oil but with a more eco-friendly face. These
lubricants must have an adequate viscosity, resistance to
sea water contamination as well as biodegradability.
They typically have a water content greater than 90% and
are highly soluble. Friction is reduced in comparison to
equivalent mineral oil/white metal bearing.
Other benefits include increased heat transfer rates and
better protection against galvanic corrosion of dissimilar
metals found in the shaft/prop arrangement. The fluid has
no measurable flash point.
17
25. When large propellers are fitted the heavy overhanging weight
greatly increases the load at the after end of the stern tube
breaking down the hydrostatic lubrication causing metal to metal
contact and seizure towards the aft end of bearing. To obviate
this it is usual to angle the shaft downwards for about 8mm over
100m length thus attempting to ensure than the weight of the
bearing is taken on the full length of the bearing. It is good
practice to leave the oil tank open to the stern tube when in port
with machinery stopped, this prevents sea water leaking into the
system. However, water has been known to contaminate
lubricating oil systems causing rusting of tail shaft particularly
when shaft is stopped for periods long enough for water to settle
in bottom of bearing. Fit only water seperator I,e, a coalescer or
cyclonic or osmosis system.
In ships with large changes in draught it is usual to fit two gravity
tanks. The upper tank is used when fully loaded or there is water
leaking in.
25
26. Water based oil replacements:
Available are water based sterntube lubricants having the
advantages of oil but with a more eco-friendly face. These
lubricants must have an adequate viscosity, resistance to
sea water contamination as well as biodegradability. They
typically have a water content greater than 90% and are
highly soluble. Friction is reduced in comparison to
equivalent mineral oil/white metal bearing.
Other benefits include increased heat transfer rates and
better protection against galvanic corrosion of dissimilar
metals found in the shaft/prop arrangement.The fluid has
no measurable flash point.
26
30. If outboard seal leaks, the following steps are to be
taken:
1. Fresh water in gravity tank to emulsify and
coagulate it, oil pumped around system to seal and
lubricated.
2. Recharge with high viscosity oil
3. disconnect oil supply line and reconnect to 45
gallon drum which is supported by block and tackle
in order to give a variable head.
4. By raising and lowering the drum the oil
pressure in the system can be made to match the
water pressure from outside (taking into account
the difference in gravities.
30
33. Split type stern tube (Ross-turnbull)
Main advantage of this system is that tail end shaft, stern tube
bearing and tapped bolts can be inspected without dry docking.
System allows stern tube to be drawn into the vessel for
inspection The bottom half bearing is supported on chocks which
in turn rest on two ford and aft machined surfaces within stern
tube boss, these chocks govern the height of shafting. A
detachable arch is attached to the lower bearing and carries the
outboard oil seal, the face of which comes into contact with a
seal seat which is fastened to and rotates with tail shaft flange.
The top half of the bearing module makes a seal on the face of
the arch and a seal along the horizontal joint on the bearing. The
bearing is held in place vertically by 4 x 50 tonne pilgrim type
jacks, these jacks also hold the two half bearings together.
Lateral positioning is by 4 x 30tonne pilgrim type jacks, two each
side.
A running track is arranged above the bearing for easy removal
of top half . A rolled race skid is provided so that the bottom half
can be transported. 33
34. Removal-The hydro mechanical seal is actuated making a seal on the
ford face of the propeller and locked mechanically in position. The
space is then drained of water.
Top half of bearing can then be removed by taking out the top vertical
jacks and using the lifting jack to allow the top half to be brought
inboard on the running track. These jacks are now fitted under the
lower half bearing to raise bearing and shaft sufficient to allow the
chocks to be removed.
The jacks are then lowered until the propeller rest on the propeller rest
built into the stern frame. Further lowering allows the bearing to move
away from the shaft until bearing is resting on roller skids. The lower
half bearing complete with oil seal can then be removed into the vessel
for examination.
Reversing the procedure enables the bearing to be replaced
Odd facts-Anti vibration locking gear fitted to jack nuts. As with a CPP
it is usual to fit a flange mounted propeller eliminating taper and keyway
with there associated problems. The tap bolts securing propeller to tail
shaft flange can be removed one at a time, crack detected and returned
to their working position.
34
36. simplex seal
A very common arrangement for oil lubricated stern tube bearings. A
simplex seal arrangement is fitted to both inner and outer ends.
The replaceable chrome liner prevents damage to the prop shaft which
would be expensive to repair.
Not shown is a rope guard bolted to the hull which prevents material from
being 'wound' into the gap and damaging the seal. Rope cutters may be
fitted with a fixed blade attached to the hull and a moving blade to the
propeller.
Oil pressure is fed to the area between the two opposite facing seals.
This pressure is governed by the draught of the vessel and is often
supplied via tanks situated at set heights. This pressure balances the sea
water pressure on the seal and prevents sea water ingress, by opening
the correct tank the pressure exerted by the oil is insufficient to cause oil
to leakage out.
Stern tube seals with oil lubrication have tended to use rubber rings
increasingly. Viton with additives has been shown to be more effective
than nitrile butadiene rubber for seal rings
36
37. Stresses in tail shafts:
Due to the considerable weight of the propeller, the tail
shaft is subject to a bending stress. There are however
other stresses which are likely to be encountered. There is
a torsional stress due to the propeller resistance and the
engine turning moment, and a compressive stress due to
the prop thrust. All these stresses coupled with the fact that
the shaft may be in contact with highly corrosive sea water
makes the likelihood of corrosion attack highly probable.
37
38. Examining a tail shaft and stern tube:
1. Before the periodic inspection the bearing weardown
should be measured.
2. After shaft removed given thorough examination.
3. On water lubricated shafts the integrity of the fit of the
bronze liner should be checked by tapping with a
hammer along its length listening for hollow noise
indicating a separation.
4. Measure wear of shaft.
5. Examine key way for cracks especially the nut thread
area.
6. Replace rubber rings.
38
39. Establishing Shaft Centre line
A telescope with cross wire is set up at the shaft centre line on the foreword
end of the engine room. A plain cross wire target is established at the aft end
on the same axis. With both in use the centre of the engine room and the
centre of the shaft on the aft peak bulkhead can be marked prior to hole cutting
for the stern tube. The required centre of the aperture in the stern frame boss
can then be found by the line of sight using a crosswire in an adjustable spider.
Replacement of the crosswire with a plug with a centre gives a location for a
divider to be used for marking off the boss for boring.
Telescope and the cross wire system can be used to check up the accuracy of
the boring operation, installation of the stern tube and siting of the shaft
bearings.
39
41. Coupling relationship method:
The rest of the intermediate shafting is dropped into
position on lower half bearings and using tail end flange as
a standard they are lined up . This is done by using feelers
between the faces of adjoining flanges, wedging the lower
half bearings until faces are parallel with a 1/10mm gap
between. A parallel block is used around the periphery of
the flanges. The intermediate bearings are chocked up by
cast iron chocks about 50mm thick and bolted down.
Couplings are continually rechecked. The thrust block is
now aligned coupling to coupling and secured.
41
43. At the for'd end of the engine room a light box emitting light through a
pin hole is fixed from the design height of the crankshaft.
Using the sighting gear in stern frame boss with solid piece fitted. The
stern frame boss is marked off for boring . The solid piece is then
exchanged for a sighting piece.
A second sighting gear with sighting piece is fitted to the bore hole in
the aft peak bulkhead. This is adjusted until the light source can be
seen through the boss and aft peak bulkhead sighting pieces. The
sighting piece is replaced by the fixed piece and the bulkhead may be
machined. The stern tube is scribed out and the p.c.d. of the bolts
which will support the stern tube flange marked off. A similar procedure
us repeated for other bulkheads. When boring out is completed the
stern tube is hauled into position, wood packing being fitted under the
flange before bolting up at the aft peak bulkhead, the external stern
tube nut is screwed up hard making a rigid connection at the after end.
The tail end shaft is now fitted into the stern tube, the flange of the tail
end shaft is now the standard by which the remaining line shafting will
be aligned.
43
44. The trailing block (or towing block), of fitted, sometimes an
ordinary plummer block is fitted (bearing material all round)
is mow fitted around tail end shaft using feelers and
wedging, chocked and bolted sown. The bearing acts also
as an auxiliary thrust with a large clearance so that there is
no possibility of it taking over from the main thrust under
normal conditions other wise the towing block would shear.
This takes the form of a split brass ring fitted to the for'd
end of the towing block which allows the tail end shaft to be
disconnected from the intermediate shaft and hence rotate
freely whilst the ship is under extended towing . The after
face of the connecting flange then rides against this brass
ring.
44
46. Optical sight line method
This method uses a micro alignment telescope which
generates a sight line between an illuminated reflective
target at one end of the shafting and the telescope
mounted at the other end. The sight line is generated at a
uniform height above the shaft vertically above the
centreline of the shaft. A movable scale or target is
employed on the intermediate shaft at bearing support
points to measure distance from shaft to the sight line. The
reflective target and movable scale consists of a magnetic
'v'-block fitted with transverse inclinometer and vertical
stand with micrometer and scale.
46
49. Shaft alignment
Taut wire method (Pilgrims wire)
Taut wire method (Pilgrims wire)
Consists of steel wire anchored above shaft at one end of system
and led over a pulley with suspended weight at the other end.
The height of the pulley and fixed anchorage are adjusted so that
they are the same distance above the shaft and are positioned
vertically over the shaft centre line. A microstaff is employed to
measure the differences in height at bearing support points
between shafts and wire, an allowance being made for wire sag.
A master inclinometer is employed to monitor ships movement
during the aligning process.
Laser system
Similar to optical arrangement except that a laser housing generates a
collimated red laser beam above the shaft which is detected by a centring
detector at the other end of the shafting. A moving scale detector is used at
intermediate bearing position.
49
52. Bearing load method
Top cover off and horizontal alignment checked by
measuring the side clearances of the shaft within the
bearings. By using the system shown the shaft is carefully
jacked up and a graph plotted. Initially a curve will be
plotted as the ships structure stress relieves itself from the
weight of the shafting, shaft still sitting on bearing material.
When curve assumes a straight line shaft has left bearing
and in order to avoid damaging the shaft only sufficient
plots will be taken to establish the slope of the straight line.
The slope of the line for each bearing is put into a computer
program which establishes the shaft system characteristic.
52
55. Main engine alignment
Bedplate and crankshaft now landed on hardwood blocks in
approximately the position, slightly lower than true. It is now
raised and jacked into position by lining the mating couplings on
thrust and crankshaft. Cast iron chock thickness now measured,
a small allowance being made to allow for individual fitting after
machining. As each chock fitted its corresponding stud bolt is
screwed through to engine seating and secured top to bottom.
Checks made to ensure that shaft alignment is maintained,
interference fit coupling bolts fitted and nuts screwed up. It
should be understood that the lining up of the shaft will only be
true for one set of conditions such as on the building stocks or
floating in a light condition. During service with variable loading
some hogging and sagging takes place but there is sufficient
flexibility in the shaft system to take care of this variation. Any
bearing which runs chronically hot is almost certainly due to bad
initial alignment.
55
59. Main engine alignment
Bedplate and crankshaft now landed on hardwood blocks in
approximately the position, slightly lower than true. It is now
raised and jacked into position by lining the mating couplings on
thrust and crankshaft. Cast iron chock thickness now measured,
a small allowance being made to allow for individual fitting after
machining. As each chock fitted its corresponding stud bolt is
screwed through to engine seating and secured top to bottom.
Checks made to ensure that shaft alignment is maintained,
interference fit coupling bolts fitted and nuts screwed up. It
should be understood that the lining up of the shaft will only be
true for one set of conditions such as on the building stocks or
floating in a light condition. During service with variable loading
some hogging and sagging takes place but there is sufficient
flexibility in the shaft system to take care of this variation. Any
bearing which runs chronically hot is almost certainly due to bad
initial alignment.
59
65. KEYS AND KEYWAYS
There are approximately 100 reported cases per year of
partial or total tail shaft failure and 200 reported cases of
lost props. Causes of this are quoted as inadequate force
fit between prop and tailshaft causing loss of peripheral grip
which allows prop to move and make contact with key. This
causes excessive dynamic load to fall on key and shaft
adjacent to keyway. This causes incipient cracks (small
and superficial ) which usually begin at high stress
concentration areas i.e. around the leading edge of the
keyway
These fatigue failures may be corrosion N.B. Temperature
variations in sea water can alter the force fits
65
67. Tailshaft keys and keyways
Abrupt changes of shape of section cause stress
concentrations to build up due to interruption of the stress
flow lines.
This build up in stress causes cracks to develop and
supports crack propagation. With this in mind it can be
seen that shapes or sections which may be subject to
great stresses; should be well rounded or gradually
tapered off to give smooth stress flow.
67
68. Round end keys used and the keyway in prop boss and
cone of the tailshaft are to be provided with a smooth fillet
at bottom of keyways, fillet radius at least 0.0125 of shaft
diameter at top of cone. Sharp edges at top of keyway to
be removed. Two screw pins secure key in keyway and the
for'd pin should be at least 1/3 of key length from for'd end.
Pin holes should have a depth not exceeding pin diameter.
Hole edges bevelled.
68
69. Stresses in tail shafts
Due to the considerable weight of the propeller, the tail shaft is
subject to a bending stress. There are however other stresses which
are likely to be encountered. There is a torsional stress due to the
propeller resistance and the engine turning moment, and a
compressive stress due to the prop thrust. All these stresses coupled
with the fact that the shaft may be in contact with highly corrosive
sea water makes the likelihood of corrosion attack highly probable.
Examining a tail shaft and stern tube
1. Before the periodic inspection the bearing wear down should be
measured.
2. After shaft removed given thorough examination.
3. On water lubricated shafts the integrity of the fit of the bronze liner
should be checked by tapping with a hammer along its length
listening for hollow noise indicating a separation.
4. Measure wear of shaft.
5. Examine key way for cracks especially the nut thread area.
6. Replace rubber rings 69
70. Shaft Bearings
The intermediate shafting if supported in plain or tilting pad
bearings, has an after most bearing which is lined top and
bottom. Roller bearings are installed in some vessels.
Plain and tilting pad bearings
The shaft supported in a plain journal bearing, will as it
rotates, carry oil to its underside and develop a film of
pressure. The pressure build up is related to speed of rotation.
Thus oil delivered as the shaft turns at normal speed, will
separate shaft and bearing, so preventing metal to metal
contact. Pressure generated in the oil film, is effective over
about one third of the bearing area because of oil loss at the
bearing ends and peripherally. Load is supported and
transmitted to the journal, by the area where the film is
generated. The remaining two thirds area does not carry load70
71. Plain and tilting pad bearings (cont’d)
Replacement of the ineffective side portions of the journal
by pads capable of carrying load will considerably increase
its capacity. Tilting pads based on those developed by
Mitchell for thrust blocks are used for the purpose. Each
pad tilts as oil is delivered to it so that a wedge or oil is
formed. The three pressure wedges give a larger total
support area than that obtained with a plain bearing. The tilt
of the pads automatically adjusts to suit load, speed and oil
viscosity. The wedge of oil gives a greater separation
between shaft and bearing than does the oil film in a plain
journal. The enhanced load capacity of a tilting pad design
permits the use of shorter length or less bearings.
71
73. SKF (Muff) coupling
Outside dia's at end of
outer muff measured
before fitting After
fitted, dia's should be
approx. 0.5mm greater
Restraining devices
must be fitted to
prevent the muffs
separating too quickly
73
76. This is fitted to
ships, the purpose
of which is to
prevent the shaft
from slipping out of
the stern tube if the
muff coupling
should fail. Its
purpose is not to
transmit torque.
Emergency astern arrangement
76
77. Coupling bolts
Elongation of a bar produces a related reduction in cross sectional area.
- A bar with the same elastic properties in all directions will have a constant
relationship between axial strain and lateral strain. This is termed the Poissons
Ratio and given by the symbol n.
- A bolt when tightened similarly causes a loss in area and diameter. In a
clearance hole this is not a problem. With a fitted bolt however, the positive
contact or 'fit' between the accurately machined bolt and reamed hole would be
affected.
-Shaft coupling bolts are tightened to force the faces of the flange together so
the friction between the faces will provide some proportion of the drive.
However, fitted bolt shanks are also designed to take a proportion of the drive. A
clearance bolt could provide the first requirement but not the second. A fitted
bolt when tightened and subject to reduction in cross section would also fail on
the second count and probably be damaged by fretting.
- A tapered bolt may be used instead of a conventional coupling bolt to obtain a
good fit and required tightening.
77
78. Coupling bolts
Parallel shank fitted bolts
have Interference fit in holes so that in the event of loss of frictional grip
between flanges then each bolt will take on equal share of the shear stress due
to torque transmission.
Parallel bolts become slack after one or two refits. Therefore taper shank bolts
have been used. An alternative is the sleeved coupling bolts.
The fit of the bolt is achieved by the tensioning of the taper shank bolt. Should
wear occur in the sleeve then this can be renewed, reusing the rest of the
assembly
78
80. Hydraulically fitted bolts
The pilgrim or margrip hydraulic bolt uses the principal
embodied by Poisson ratio to provide a calculated and definite
fitting force between bolt and hole Center load rod fitted into
hollow coupling bolt and hydraulic head fitted.
- High pressure oil pumped into head pushing down, seal,
piston and rod .This action stretches the bolt ( within its elastic
limit ) and reduces its diameter sufficiently for a sliding fit into
the hole.
- Fluid pressure is released allowing bolt to expand and tightly
grip within the hole with a radial grip of about 2.36 Kg/mm2.
-Simultaneous longitudinal contraction of the bolt having
already fitted the nut hand tight, exerts considerable
compressive force which is about 2 1/2 x greater than that
which can be achieved by normal torque tightening.
- Hydraulic head and loading rod now removed and a
protective cap and seal screwed back on. 80
82. PILGRIM NUT
Assembly
Propeller bedded to tailshaft and jacked up to usual shop mark. The
Pilgrim nut is then screwed on the shaft with the loading ring against
the prop boss. With the lever operated, high pressure grease gun,
grease is pumped into the inner tube inside the nut at around 600
bar, ( w.p. stamped on nut, not to be exceeded), the prop will be
pushed sufficiently up the taper to give the required frictional grip.
The pressure is then released and the nut is rotated until it is hard
up against the aft face of the prop hub and locked, fair water cone
then fitted.
Removal
After removal of fair water cone and the locking plate, the pilgrim nut
is removed, reversed and together with a loose shock ring is
screwed back onto the shaft. A strong back is fitted and secured
with studs to the prop boss.
Grease is now inserted to the system expanding the inner tube
forcing the loading ring, strongback, withdrawal studs and prop aft.82
83. Advantages:
1. Precise tightening working on a measured
applied load
2. Adequate interference fit
3. no heat used
4. Simple and safe to operate
5. No shock loads applied
6. Considerable saving in man power and time
83
85. Controllable Pitch Propellers
The CPP consists of a flange mounted hub inside which a piston arrangement
is moved fore and aft to rotate the blades by a crank arrangement. The piston
is moved by hydraulic oil applied at high pressure (typically 140 bar) via an Oil
transfer tube (OT tube) This tube has and inner and outer pipe through which
Ahead and astern oil passes. The tube is ported at either end to allow oil flow
and segregated by seals.
Oil is transferred to the tube via ports on the shaft circumference over which is
mounted the OT box. This sits on the shaft on bearings and is prevented from
rotation my a peg. The inner bore of the box is separated into three sections.
The ahead and astern and also an oil drain which is also attached to the
hydraulic oil header to ensure that positive pressure exists in the hub and
prevents oil or air ingress
The OT tube is rigidly attached to the piston, as the piston moves fore and aft
so the entire length of the tube is moved in the same way. A feedback
mechanism is attached to the tube, this also allows for checking of blade pitch
position from within the engineroom.
85
86. Controllable Pitch Propellers
Advantages
1. Allow greater maneuverability
2. Allow engines to operate at optimum revs
3. Allow use of PTO alternators
4. Removes need for reversing engines
5. Reduced size of Air Start Compressors and receivers
6. Improves propulsion efficiency at lower loads
Disadvantages
1. Greater initial cost
2. Increased complexity and maintenance requirements
3. Increase stern tube loading due to increase weight of assembly, the stern
tube bearing diameter is larger to accept the larger diameter shaft
required to allow room for OT tube
4. Lower propulsive efficiency at maximum continuous rating
5. Prop shaft must be removed outboard requiring rudder to be removed for
all prop maintenance.
6. Increased risk of pollution due to leak seals
86
87. SHAFT BEARINGS
The intermediate shafting if supported in plain or tilting pad
bearings, has an after most bearing which is lined top and
bottom. Roller bearings are installed in many vessels.
Plain and tilting pad bearings
The shaft supported in a plain journal bearing, will as it
rotates, carry oil to its underside and develop a film of
pressure. The pressure build up is related to speed of
rotation. Thus oil delivered as the shaft turns at normal
speed, will separate shaft and bearing, so preventing metal
to metal contact. Pressure generated in the oil film, is
effective over about one third of the bearing area because
of oil loss at the bearing ends and peripherally. Load is
supported and transmitted to the journal, by the area where
the film is generated. The remaining two thirds area does
not carry load. 87
88. Plain and tilting pad bearings (cont’d)
Replacement of the ineffective side portions of the journal
by pads capable of carrying load will considerably increase
its capacity. Tilting pads based on those developed by
Mitchell for thrust blocks are used for the purpose. Each
pad tilts as oil is delivered to it so that a wedge or oil is
formed. The three pressure wedges give a larger total
support area than that obtained with a plain bearing. The tilt
of the pads automatically adjusts to suit load, speed and oil
viscosity. The wedge of oil gives a greater separation
between shaft and bearing than does the oil film in a plain
journal. The enhanced load capacity of a tilting pad design
permits the use of shorter length or less bearings.
88
89. Any bearing instability, regardless of its nature is called 'oil whip'.
Bearing instability falls into two types:
i. Half frequency whirl
ii. Resonant whip
The most effective bearing to prevent oil whip and dampen shaft
vibration is the tilting and multiple shoe bearing.
Oil film operates at a lower temperature than a comparable full sleeved
bearing.
Tilting pad bearings are in common use on steam turbines, high speed
reduction gears, centrifugal compressors and line shafting.
89
91. Split Shaft bearings
Inner Ring
Rotating inner ring is in two halves with a scarf or diagonal joint so
that the tendency of the joint to open due to the weight of the shaft
is reduced when the joint is at bottom centre. The scarf also allows
more progressive transition of the roller over the joint reducing noise
and vibration
Cage And
rollers
The cage and rollers are in a matched pair with a diagonal split
Pedestal
Cap
Clamps the splt cartridge. The joint is spherical allowing upto 2 1/2'
of swivel without effect.
Split
cartrdige
Is located by dowels and holds the outer ring in position. radial
socket screw attach the outer ring securely to the split cartridge
Clamping
ring
This rotating ring secures the split inner ring assembly and is joined
by socket head screws
91
92. Split Shaft bearings (cont’d)
Clearance exists between the inner ring and thesplit
cartridge. This allows movement of the shaft between
thrust pads during ahead and astern movements. This also
allows for thermal expansion of the shaft.
Plane white metal bearings offer a relatively high frictional
resistance to rolling but are cheap and not subject to
brinelling or corrosion.
Roller bearings are expensive but offer little resistance to
rolling. However, they are susceptible to brinelling when
stationary.
The above design removes the major disadvantage of
assembling the bearing onto the shaft which would
normally require shaft removal.
92
93. SECURING PROPELLERS
HYDRAULIC FLOATING OF PROPELLERS:
Used for keyless propellers, ensures the correct
interference fit using measured oil pressures for expanding
the boss and hydraulic jacks or a Pilgrim nut for pushing it
up or down the tailshaft taper. No heavy slogging required
and low shock loads are applied, quick and safe.
A disadvantage is loss of bearing area due to oil grooves
which means that propeller must be longer or greater in
Dia to give sufficient area to transmit the torque.
94. - To remove, nut just slackened back.
- Oil injection applied to expand the boss which allows
propeller to move off the taper.
Another disadvantage of wet fitting over dry fitting is that
wet boss expansion stress I s 30% greater than dry fitted
which means that boss must be thicker.
94
96. Usually fitted on large diameter shafting. Usually
hydraulically floated and keyless. Difficult to bed large
props to taper, easier to bed sleeve. Also each time a prop
is refitted, prop bore becomes larger, this is accentuated in
large bore dia props. Hence, after a few refits the prop
moves to far up the shaft, more economical to replace the
sleeve than the whole prop.
96
97. Pearlitic cast iron used to mate with forged mild
steel shaft because this combination offers the
greatest resistance to fretting which can be caused
by prop excited vibration
Molecular fretting can occur internally, generally
from the center outward due to molecular rubbing
together. Surface fretting occurs at the surface due
to two items moving over each other due to
vibration.When fitting or removing, heat not to be
used since it may effect the mechanical properties
of the resin. Wedging or withdrawal systems
should not be used since this would cause
shearing of the araldite.
97
98. Traditional method:
Shaft turned to top centre, i.e. when key is on top,
convenient for key way inspection and prop slinging. Shaft
locked, and prop nut just slacked.
Coupling bolts at tail end flange removed, if lignum vitae
bearing- stuffing bearing removed and tailed flange shored
up against aft peak bulkhead.
Secured lifting gear to propeller, then wedge off prop using
box wedges between stern tube nut and ford face of prop.
If tail end and bronze liner are to be inspected then it must
be brought inboard which requires the removal of one or
two lengths of intermediate shafting.
98
99. Bolted
Controllable pitch propellers require a hollow prop shaft for the
oil and feed back tubes to pass through. non of the above
methods are suited to this.
Instead the propeller is bolted to a flange, the other end of the
propshaft must therefore be parallel to allow removal from the
stern bearing.
The prop shaft is attached to the intermediate shaft by a 'muff'
coupling. Once the bolts have been tightened they are secured
by tack welding locking bars across the heads. 99