2. What we can overhaul in Alloa:
• Submersible pumps & motors, including full
performance test
• Multistage high speed cartridge pumps
• Multistage through bolt pumps
• Multistage vertical pumps
• Horizontal split casing pumps
• All types of valves, including function test
• Actuators, including function test
• Hydro Electric Turbines and Valves
3. Sectors that we support:
• Oil & Gas
• Nuclear
• Conventional Power
• Defence
• Water treatment
• Petro chemical
• Waste water
4. High speed Multi-stage pumps
4TRILLIUM Flow Technologies
What do in house to achieve a smooth running pump for you:
Here in our Alloa Works in Scotland we have a workshop called the High Integrity Pump Cell. In
which we have a team of specialists who are highly trained in these types of units. They follow
this tried and tested methodology, working to Customer approved Quality Plans:
• Initial condition assessment
• Total dissassembly, on our bespoke specially designed rigs
• Calcium (soft) blasting, to remove surface corrosion, scale & magnetite deposits
• 100% dimensional survey
• 100% running clearance survey
• Surface finish survey
• PMI examination
• NDT examination
• Electrical & Mechanical run out tests
When the unit is ready to be assembled, we then call on our in house machine shop to perform the following
steps:
• Skimming of pump rotating element
• Dynamic balancing (full rotating element with an average mass of 750kgs), balancing to a balance grade
of G1 (18ton capacity)
• Vertical bored (3’, 4’, 5’, 10’ & 24’) to ensure stationary component centre line and machining are
concentric and accurate
Once everything has been machined and thoroughly cleaned & inspected, the components are returned to
our High Integrity Pump Cell for final checks and assembly by our team of specialists. Where they work to
another Quality Plan to ensure the unit is assembled to the highest Quality standards.
5. Submersible Motors & Pumps
5TRILLIUM Flow Technologies
Submersible Motors & Pumps:
Based on the same overhaul methodology as The High
Integrity Pump Cell, we can totally strip down,
overhaul, manufacture spares, balance, assemble and
performance test submersible motors and pumps.
Full re-cores and rewinds to original specifications is
an ability that we are very proud of.
The Motors can be subjected to the following tests:
• Megger,
• Flash,
• Resistance,
• Temperature measurement
• No load & full performance tests to BSEN60034.
The performance tests are carried out to replicate site
conditions and can be witnessed remotely through our
online test portal.
We also, hold overhauled motors and pumps to be
called off within 24 hours, should the need arise to
fully support our customers.
6. Valves & Actuators
6TRILLIUM Flow Technologies
Valve & Actuator Workshop.
On site we have a dedicated valve and actuator workshop, in which we
overhaul the following:
• Safety valves
• Isolation valves
• Control valves
• Pneumatic, electrical & hydraulic actuators
• Torsion bar hysteresis
We can test our overhauled valves on our bespoke test rig, operating
to pressures up to 10,000 p.s.i. and with the addition of our actuator
test rig we offer a full flow control solution to our customers.
7. Test Facility
7TRILLIUM Flow Technologies
During 2020 we are undertaking a major upgrade of our existing
in House Test Facility. The main well has a depth of 10m, and
can hold 550m ³ of test medium.
• Test beds – surface mounted & wet well
• Cooling package to absorb 1,250kW
• Equipment lifting up to 72 tonnes
• 50 Hertz from LV to 11Kv (5,000kVA)
• 60 Hertz from LV up to 6.6kV (1,500kVA)
• Variable speed drive <2MW
• Up to 10,150m³/hr 37,000GPM
• Up to 40bar (higher test pressures by arrangement)
• Up to 4,250kW / 5,700BHP
In House testing removes risk to the end user!
8. Machine Shop
8TRILLIUM Flow Technologies
On site we have the following machines, all operated by
highly trained, experienced & dedicated machine men:
• Horizontal Bore Mills, 2 off
• Radial Arm Drills
• Vertical Boring m/c’s 3’, 4’, 5’, 10’ & 24’
• Conventional Lathes, 5 off
• CNC Lathe’s, Borer and Milling m/c’s
• Balancing m/c’s, 2 off
• Surface grinder
• In 2020 we are installing a new 5 axis CNC Lathe
All machining work is placed in our scheduling /
planning tool to ensure key required for dates are met.
We also have the full support from our Quality
Department, who look after m/c servicing, measuring
gauge certification, operator up skilling and inspection
of finished components.
9. Coatings Department
9TRILLIUM Flow Technologies
Within our coatings department, we have
the following capabilities:
• Calcium blasting
• Shot blasting, both with 20’ and 40’ booths
• Spray booths
• Coatings testing
• Various component build up techniques
• Bespoke fully ventilated paint kitchen
• Full dedicated Bay for any coatings work
• Over 60 years experience working each day
on your components
Our coatings systems combine engineering and
coating expertise to provide efficiency upgrades
to most pump and valve internals.
10. Spares Supply
10TRILLIUM Flow Technologies
Spares supplied from the people who use them.
Taking another risk out of the process, we have extensive knowledge of
pump, motor and valve spares. We can identify prior to manufacture that
form, fit & function is correct
Within Alloa we have our spares supply team, who work closely with our
Contracts Engineers, Quality Department & Machine Shop to fulfil our
customers spares needs.
We can manufacture from new and also procure from the market. Our
global supply chain is vetted regularly and performance is monitored
constantly to ensure the components are manufactured correctly to the
most stringent QA standards.
Supplied spares can be used in overhauls or to replenish our customers
stock holding.
11. 11
Reverse Engineering
TRILLIUM Flow Technologies
Technologies and Software - Continual Improvement
- Trillium have invested heavily in advanced technology and software and have implemented DMS
controls to improve efficiency and greater control over process.
- During 2019 & 2020 Trillium Directors have approved a six figure CAPEX spend on APS technology
encompassing:
- 2 x Portable Romer Metrology Arm’s with integrated laser scanners
- Artec Leo – Wireless Laser Scanner
- 2 x Niton - PMI Guns
- Geomagic Design X licenses – Reverse Engineering Software
- Geomagic Control X licenses – Inspection Software
12. 12
Reverse Engineering
2 Data Acquisition
All critical component information identified, captured and recorded
1 ENG-IMS-FA17 Request Form
Project details, equipment details, serial numbers, site details, duty
details, operational issues, work scope required.
3 Data Review and Approval DMS
Review of all data acquisition to ensure compliance with process.
Suitably qualified/experienced engineer review. Upload to DMS with
reference to project, equipment and other unique identifiers.
Electronic sign off by qualified/experienced engineer.
4 Model and Manufacturing Information
Review ENG-IMS-FA17 request for work scope requirements and
product background. Develop model and required manufacturing
information utilizing relevant design standards.
5 Design Verification
Suitably experienced engineer reviews and approve designs. Utilize
standards, experience and CFD/FEA software to verify compliance
and performance.
6 Manufacture Component
Multidiscipline team review enquiry and create necessary QP.
Manufacture components using QP and generated design
information. Inspect component and collate QA documentation (LTRP
or other) to ensure compliance with customer order.
Stages of Reverse Engineering Process
TRILLIUM Flow Technologies
Data Acquisition
Design and
Manufacture
14. Quality
14TRILLIUM Flow Technologies
Trillium Flow Services UK Ltd, operates an integrated management system which is independently assessed by LRQA for
compliance to:
• ISO9001:2015
• ISO14001:2015
• ISO45001:2018
Our IT systems have been independently checked for compliance
to the Cyber Essentials Scheme.
We are registered with FPAL/Achilles.
We utilise Q-Pulse to manage:
• Documents
• Incidents and Occurrences
• CA/PA
• Calibration
• Audits
15. Additional services from Alloa:
Key services include:
• Asset Management contracts
• Stock Management/Inventory control
• Engineering & technical solutions
• Upgrading and re-rating of equipment
• Re-engineering & spare parts
• Customer training
• Field service support, installation & commissioning
• Large scale project management for Hydro and Nuclear
• Supply of new rotating equipment, submersible motors
and valves