The Stabilization of Polypropylene and TPO: An Overview

1
© 2012 BotkinChemie
THE STABILIZATION OF POLYPROPYLENE & TPO:
AN OVERVIEW
James H. Botkin
dba BotkinChemie, Portland, ME USA
jim@botkinchemie.com
Abstract
The degradation and stabilization of polypropylene and TPO are reviewed. Polypropylene-based
materials degrade when exposed to heat or light by an oxidative process in which scission of the polymer
chains predominates. This eventually leads to a number of undesirable effects that compromise the useful
life of the polymer. Oxidation can take place during melt processing operations, at elevated temperatures
during end use, or from exposure to ultraviolet light (i.e. in sunlight).
Stabilizer additives have been developed that are very effective for improving the stability of
polypropylene and TPO to oxidative degradation. Most of these products act by chemically disrupting
the oxidation process through the scavenging of free radical and peroxide intermediates. Examples of
commonly used stabilizer additives include hindered phenols, phosphites and phosphonites, thioethers,
hydroxylamines, hindered amine light stabilizers (HALS), benzoates, and UV absorbers. The mechanism
of action of each type of stabilizer is reviewed and examples of commercial products are provided.
Degradation during melt processing results in melt flow shifts and discoloration. Combinations of
hindered phenols and phosphites represent the state of the art for the stabilization of polypropylene and
TPO under these conditions. Systems incorporating partially-hindered phenols (e.g. AO-4) and/or high
performance phosphites (e.g. P-2, P-3), or phosphonites (e.g. P-4) provide the highest level of
performance in terms of melt stability.
Long-term thermal exposure of a part during end use can result in the deterioration of mechanical
properties as well as discoloration. Systems based on combinations of hindered phenols and either
thioethers or HALS (especially HALS-5) can significantly extend the useful life of polypropylene and
TPO under these conditions. Systems based on HALS-5 in combination with hindered phenols are most
appropriate for use in applications where light stability is also required in the end use application.
Degradation induced by exposure to sunlight results in changes in appearance and the loss of mechanical
properties. Systems based on HALS are the state of the art for the light stabilization of polypropylene and
TPO. In cases where higher performance is needed, improvements can often be achieved by using
synergistic combinations of HALS with other additives such as benzoates, ultraviolet absorbers, and some
phenolic antioxidants (especially AO-2).
Stabilizer additives can sometimes give rise to unexpected, undesired effects such as blooming,
automotive fogging, warehouse discoloration (gas fading), and interactions with automotive coatings.
Guidelines are provided to avoid these problems though the proper selection of the additives.

2
Introduction
Polyolefin-based materials such as polypropylene and TPO are widely used in automotive components
due to their excellent balance of physical properties, ease of processing, recyclability, and good cost-
performance. These materials must be properly stabilized in order to survive melt processing operations
as well as to meet the weatherability and long-term thermal stability requirements of automotive
applications. This is normally accomplished using additives such as antioxidants and light stabilizers.
The range of available stabilizer additives is huge and formulating with them can be challenging. This
paper provides an overview of some of the more common stabilization additives used in polypropylene
and TPO, with an emphasis on products useful in thick-section automotive applications. Specific topics
to be covered include the oxidative degradation of polyolefins, descriptions of stabilizer additives and
their functions and mechanisms of action, test methods, and basic formulation guidelines to meet
performance requirements and avoid common problems.
Oxidative Degradation of Polyolefins
When organic materials such as polyolefins are exposed to conditions such as heat, ultraviolet light, or
mechanical stress in the presence of atmospheric oxygen, free radicals are formed which initiate the
oxidation process. The basic chemistry of oxidation has been known for over sixty years.[1] This
process is characterized by initiation (equation 1), propagation (equations 2 & 3), chain branching
(equation 4), and termination (equation 5) steps:[2]
Initiation: •!" PHP (1)
Propagation: •!!"+• OOPOP 2 (2)
•+!!"!+•!! POHOPHPOOP (3)
Chain Branching: OHOPOHOP h
•+•!"" #"!! $/%
(4)
Termination: 22 OPOOPOOP +!!!"•!! (5)
The alkoxy radical derived from the polypropylene hydroperoxide (in equation 4) readily undergoes
fragmentation to give chain scission (equation 6). This is consistent with studies showing chain scission
dominates over cross-linking in the oxidation of polypropylene.[2,3]
CH2
C
O
CH2
CH3
CH2
O
CH3
CH2
.
+ . (6)
Oxidation of polypropylene and TPO can take place during high temperature melt processing operations,
during end use at elevated temperatures (e.g. in under-the-hood applications), or during exposure to
sunlight. The damaging effects of oxidation manifest themselves somewhat differently depending on the
conditions, but in all cases the changes that take place can compromise the useful properties of the
material and limit the lifetime of the part.
Introduction to Stabilizer Additives
Stabilizer additives function in large part by chemical disruption of the oxidation process. By reaction of
stabilizers and/or their transformation products with the free radicals and hydroperoxides formed in the
initiation and propagation steps (equations 1-3), oxidation can be inhibited or retarded and the useful life
of a part can be significantly extended. These protective additives are characterized by their chemistry

3
(e.g. hindered phenols, phosphites) and/or function (e.g. radical scavengers, peroxide decomposers, UV
absorbers). Some common families of stabilizer additives used in polypropylene and TPO include:
• Hindered phenols,
• Phosphites and phosphonites,
• Thioethers,
• Hydroxylamines,
• Hindered amine light stabilizers (HALS),
• Benzoates, and
• Ultraviolet (UV) absorbers.
Different families of additives are reactive with different intermediates in the oxidation process (e.g. free
radicals vs. hydroperoxides), present different levels of reactivity (e.g. at different temperatures), and
have different degrees of stability during exposure to environmental conditions such as high temperatures
or UV light. As a result of their inherent reactivity and stability, some additives function primarily as
melt processing stabilizers at high temperatures, some as thermal stabilizers but at lower temperatures
(i.e. in the solid state), and still others as light stabilizers.
It is also well known that in order to provide the most effective protection against oxidation it is
beneficial to combine additives acting by different mechanisms, i.e. by attacking the oxidation process at
multiple steps. These combinations often exhibit a level of performance far superior to that of their
individual components used alone.
Polymers and parts produced from them can be oxidized under a wide range of conditions encountered in
their manufacturing and end use. Combinations of additives (often referred to as systems) are usually
needed to provide effective protection.
A summary of the function of different families of stabilizer additives is presented in Table 1. In the
following sections, each class will be presented in greater detail and test methods and general formulation
guidelines will be provided along with illustrative examples.
Table 1. Protective Effects of Stabilizer Additives.
Stabilizer Class Reactivity
High Temperature
Melt Processing
Heat Stability
(Solid Phase)
UV / Light
Stability
Hindered phenols POO .
  
Phosphites POOH 
Thioethers POOH 
Hydroxylamines POO .
/ POOH 
HALS P .
/ POO .
 
Benzoates POO .
  
UV absorbers hν 
 Primary effect
 Secondary effect
Hindered Phenols
Hindered phenol antioxidants are highly effective to prevent oxidation in polyolefins both during
processing in the melt and during long-term heat aging in the solid phase. These additives also have an
influence on the light stability of polypropylene and TPO.
Examples of some commonly used commercial hindered phenols are shown in the Appendix. These
include “fully hindered” (ortho di-tert-butyl substituted as in AO-1, AO-2, and AO-3) and “partially
hindered” (ortho methyl-tert-butyl substituted as in AO-4 and AO-5) types.

4
Hindered phenols function by reaction with peroxy radicals (formed in step (2) of the oxidation process)
to give hydroperoxides (Scheme 1), thus terminating the oxidation chains.[4] The resonance stabilized
phenoxy radical formed in this process is generally of sufficient stability not to reinitiate the oxidation
process by abstraction of hydrogen from the polymer, although this can be an issue with more reactive
unhindered phenols. Combinations of hindered phenols with peroxide decomposers (e.g. phosphites or
thioethers) are widely employed and often provide enhanced protection during melt processing or long-
term heat aging.
+ POO^ + POOH
^ ^
^
OH
R
O
R
O
R
O
R
O
^
R
O
^
R
Scheme 1. Scavenging of Peroxy Radicals by Hindered Phenols
and Resonance Stabilization in Hindered Phenoxy Radicals.
Phosphites & Phosphonites
Phosphites and phosphonites are used as melt processing stabilizers in polyolefins, usually in
combinations with hindered phenols or hydroxylamines. These additives function as hydroperoxide
decomposers (Scheme 2).[5] They are most effective at the high temperatures encountered in melt
processing operations but much less so in the solid phase at lower temperatures.
Examples of commercial phosphite stabilizers are provided in the Appendix. Phosphite P-1 is a general-
purpose product very widely used in polypropylene and TPO. The “high performance phosphites” (P-2
and P-3) and the phosphonite P-4 are more reactive and tend to be used in applications employing high
temperature and/or high shear processing conditions.
As esters of phosphorous acid, all phosphites are subject to hydrolysis and this can lead to problems such
as black specks and equipment corrosion. When using phosphites it is important to minimize exposure of
the product to moisture, keeping containers tightly sealed when not in use. The high performance
phosphites P-2 and P-3 and the phosphonite P-4 tend to be more moisture sensitive than the general-
purpose product P-1.
Thioethers
Thioether antioxidants are used to improve the long-term thermal stability of polypropylene and TPO in
the solid phase. Like phosphites, thioethers function as hydroperoxide decomposers (Scheme 2),[6] but
tend to be more reactive at lower temperatures (<160o
C). Combinations of thioethers with hindered
phenols are particularly effective.
Examples of commercial thioether stabilizers are given in the Appendix. Thioether TS-1 is a low-cost,
general-purpose product that is widely used in polypropylene and TPO applications. TS-2 is a higher
performance product with lower volatility, excellent compatibility, and a higher sulfur content that may
be more suitable for use in demanding applications.

5
+ POOH
+ POOH
+ POH
+ POH
RO P OR
OR
RO P
O
OR
OR
R
S
R R
S
R
O
Scheme 2. Scavenging of Hydroperoxides by Phosphites and Thioethers.
Antagonistic interactions between thioethers and HALS are known, the effect of which is to compromise
the light stabilization performance of the HALS. This effect appears to result from an interaction between
the basic HALS and acidic transformation products of the thioether.[7] While it has been suggested that
this effect may be overcome through the use of specific acid neutralizers,[8] combinations of thioethers
and HALS are not typically recommended for the stabilization of polypropylene and TPO.
Hydroxylamines
Hydroxylamine antioxidants are used as non-discoloring melt processing stabilizers in polyolefins. It has
been postulated that these additives function both as peroxy radical scavengers and peroxide
decomposers.[2] While excellent melt processing stabilizers, hydroxylamines are not effective to prevent
oxidation in the solid phase and must be used in combination with either a hindered amine light stabilizer
(HALS) or a hindered phenol.[9,10]
Examples of hydroxylamine stabilizers are given in the Appendix. Note that the amine oxide H-3, while
not a hydroxylamine, rearranges to form an active hydroxylamine via a Cope Rearrangement during melt
processing at high temperatures.
Hindered Amine Light Stabilizers (HALS)
The development and commercialization of HALS in the 1970’s revolutionized the light stabilization of
polyolefins. The development of these highly effective light stabilizers has been critical to the successful
use of polypropylene and TPO in weatherable applications. HALS also contribute to the thermal
oxidative stability of polyolefins in the solid phase, especially at lower temperatures (<120o
C).
Examples of commercial hindered amines are given in the Appendix. By varying attributes such as the
molecular weight, linking groups between the active piperidine moieties, and substitution on the
piperidine nitrogen atom, products with a range of stabilization activities and secondary properties
(physical form, basicity, volatility, solubility, etc.) are obtained. HALS are conveniently classified as
low- to medium-molecular weight (HALS-1 through HALS-3) or high molecular weight types (HALS-4
and HALS-5). While HALS of all molecular weights are effective as light stabilizers, only the medium
and high molecular weight types are effective to improve thermal oxidative stability.
It has been long recognized that hindered amines and their transformation products (i.e. nitroxyl radicals
and iminoether or “NOR” derivatives) are capable of stabilizing polyolefins through multiple mechanisms
involving the scavenging of free radical and peroxide intermediates in the oxidation process.[11,12] An
important feature differentiating hindered amines from other classes of stabilizers is their ability to act by
a regenerative mechanism, which was first proposed by Denisov and coworkers (Scheme 3).[13] While
the exact nature of this regenerative mechanism is still subject to debate,[14] it is generally accepted that a
single hindered amine is capable of deactivating multiple oxidation chains.[12] However, evidence also
exists that the regeneration mechanism is less efficient in polypropylene than in other polyolefins.[14]

6
N
H
N
O
N
OP
P
P-O-OP-O-O-P
.
.
.
Scheme 3. The “Denisov Cycle” Mechanism Proposed for Hindered Amine Light Stabilizers.
Benzoates
The use of derivatives of 3,5-di-tert-butyl-4-hydroxybenzoic acid (B-1, B-2; Appendix) as light stabilizers
for polyolefins predates that of hindered amines. Like other hindered phenols, the benzoates inhibit the
oxidative degradation process by scavenging free radicals.[15] However, compared to conventional
hindered phenols, benzoates are characterized by a higher level of inherent light stability. These products
also contribute to the thermal oxidative stability of polyolefins, both in the melt and at lower temperatures
in the solid phase. Note that benzoates are sometimes erroneously referred to as “UV absorbers”, although
they do not absorb at wavelengths longer than about 300 nm.
The photochemistry of benzoates needs to be considered when selecting the most appropriate product for
use in a particular application. B-1 is well known to undergo a Photo-Fries rearrangement on exposure to
light (Scheme 4),[15] giving a 2-hydroxybenzophenone derivative which is an effective UV absorber but
also absorbs visible light and can be discoloring. The rearrangement can be inhibited to some degree and
the amount of discoloration reduced by using B-1 in combination with an ultraviolet absorber.
O
O
OH
OH
O O
H
h!
Scheme 4. Photo-Fries Rearrangement of Benzoate Light Stabilizer B-1.
Ultraviolet Absorbers
Ultraviolet (UV) absorbers act largely by shielding the interior of the part from damaging UV radiation.
Before the advent of hindered amines, light stabilization was accomplished with systems based on UV

7
absorbers in combination with other additives such as benzoates. Today UV absorbers are sometimes
used in combination with HALS and other additives for the stabilization of polypropylene and TPO.
They are also used in polyolefin packaging applications to protect the package content from the effects of
UV radiation.
All of the compounds of this class share several general characteristics:
1. Strong UV absorption, especially in the 290 nm to 350 nm range which is very damaging to
organic materials, and
2. Excited states formed upon UV absorption relax to the ground state extremely rapidly
(picosecond time frame) and efficiently via radiation-less processes, which imparts high
efficiency and excellent photostability.
Chemical classes of UV absorbers suitable for use in polyolefins include 2-hydroxybenzophenones (e.g.
UVA-1), 2-(2-hydroxyphenyl)-2H-benzotriazoles (e.g. UVA-2, UVA-3), and tris-aryl-o-hydroxyphenyl-
s-triazines (e.g. UVA-4). Chemical structures of representative UV absorbers are given in the Appendix.
Stabilizers in Action: Examples and Formulation Guidelines
Melt Processing Stabilization
Oxidative degradation can take place during melt processing operations associated with resin
manufacturing and compounding operations as well as during the fabrication of finished parts. The
degree of degradation is influenced by factors such as the processing temperature, residence time, shear,
and concentration of oxygen. Melt processing stability is particularly critical in high temperature or high
shear processing operations. It is also important for processes that generate large amounts of production
scrap that must be recycled, such as sheet extrusion and thermoforming. In such operations, it is to be
expected that a significant fraction of the polymer will be subjected to multiple heat histories in which
degradation can occur.
Changes in molecular weight resulting from oxidation can affect the melt viscosity (and hence processing
characteristics) and also the mechanical properties of the polymer. Chain scission processes tend to
dominate in polypropylene during degradation in the melt, and thus the molecular weight tends to
decrease after processing. Along with these changes, oxidative degradation during processing also results
in the formation of defects (such as hydroperoxides) that can negatively affect the long-term thermal
stability and the light stability of parts during their end use.
Maintaining stable color after melt processing is also important to polymer producers and processors. As
a consequence of oxidation processes taking place during melt processing, hindered phenolic antioxidants
are oxidized to highly colored products such as quinones that cause a visible discoloration of the
polymer.[16] Other additives may either inhibit or accelerate the discoloration process. In particular,
strongly basic additives such as hindered amine light stabilizers (HALS) can increase the discoloration
associated with oxidation products of hindered phenols.
The melt processing stability of polypropylene is often assessed in the laboratory using multiple pass
extrusion experiments, in which changes in the melt flow index (MFI) and color of the polymer are
measured as a function of the number of extrusion passes.[2]
The MFI of the polymer is defined as the mass of polymer, in grams, flowing in ten minutes through a
capillary of a specific diameter and length by a pressure applied via a specified weight at a specified
temperature. The method is described in the ASTM D1238 standard. For polypropylene, testing is
conducted at 230o
C using a 2.16 kg weight. MFI is regarded as an indirect measure of molecular weight,
with higher values corresponding to lower molecular weights. MFI is also inversely proportional to
viscosity of the melt at the conditions of the test. Mechanical properties are also affected by the
molecular weight of the polymer. All other things being equal, polypropylene resins of lower MFI

8
(higher molecular weight) tend to have higher mechanical strength than resins of higher MFI (lower
molecular weight). In multiple pass extrusion experiments in polypropylene, the MFI tends to increase
with each extrusion pass as a result of oxidative degradation. Smaller increases in MFI after multiple pass
extrusion are indicative of better processing stability.
In laboratory experiments, the color of a test specimen is measured on polymer pellets or molded plaques
using a spectrophotometer and is expressed as a point on a three-dimensional color space. In natural (un-
pigmented test specimens), color is often expressed as Yellowness Index (YI), which is defined in the
ASTM E313 (for translucent or opaque samples) or ASTM D1925 standards (for transparent samples).
Higher YI values are associated with a greater perceived yellowness to the naked eye. Smaller increases
in YI after multiple pass extrusion are suggestive of better processing stability.
Combinations of hindered phenols and phosphites represent the state-of-the-art for the melt processing
stabilization of polypropylene and TPO. Systems based on combinations of AO-1 and P-1 (usually at a
1:1 or 1:2 ratio) are among the most widely used, and as shown in Figure 1 give excellent MFI stability
under typical processing conditions.
Figure 1. Melt Stabilization of PP Homopolymer.
Multiple Pass Extrusion, 260o
C melt temperature.
All formulations contain 0.1% calcium stearate. Data from Reference [17]
In processes for which a higher levels of processing stability are needed, combinations of a partially-
hindered phenol such as AO-4 with P-1 can provide improved melt stability (Figure 2).[18]
Alternatively, this objective can also be met through the use of AO-1 in combination with a high
performance phosphite such as P-2, P-3, or the phosphonite P-4 (Figure 3). Systems based on high
performance phosphites also provide reduced discoloration in some cases, which appears to be dependent
on the particular resin grade used.

9
C melt temperature.
C melt temperature.
Systems based on hydroxylamine stabilizers alone or in combination with other additives also provide
excellent MFI stability, often with less discoloration than conventional systems based on combinations of
hindered phenols and phosphites.[9,10]

10
Long-Term Thermal Stabilization
Polypropylene and TPO are exposed to the elevated temperatures during many end use applications. The
susceptibility to oxidation is dependent on factors such as the temperature, the thickness of the part, and
the processing history. Long-term thermal stability is particularly important in under-the-hood
applications, interior trim components, and also in some exterior parts near the engine compartment.
Oxidation of polypropylene takes place readily at elevated temperatures and results in undesirable effects
such as a deterioration of mechanical properties and discoloration. In laboratory tests, the long-term
thermal stability of a material is generally assessed by heating test specimens in a circulating air oven and
measuring changes in appearance or mechanical properties as a function of exposure time. The thermal
degradation of polypropylene at higher heat aging temperatures (~150o
C) is often characterized by a very
sudden onset, and often the onset of degradation can be determined by visual examination. In these cases
the formation of discolored areas on the test specimen or crumbling can be taken as the time to failure. At
lower temperatures (<140o
C), thermal oxidative stability is more often assessed by measurement of
tensile properties.
Systems based on hindered phenols alone or in combination with other additives represent the state of the
art for the long-term thermal stabilization of polypropylene and TPO. The high molecular weight
hindered phenol AO-1 tends to outperform other products when used without a synergist (Figure 4).[2]
Combinations of hindered phenols and thioethers (e.g. TS-1 and TS-2) usually provide superior
performance as compared to hindered phenols used alone.[2] It has been reported that the synergy is
particularly pronounced in the case of partially hindered phenols such as AO-5 (Figure 5).[19]
Figure 4. Long Term Thermal Stabilization of PP Homopolymer.
Heat aging at 149o
C, compression molding, thickness 1 mm.

11
Figure 5. Long Term Thermal Stabilization of PP Homopolymer.
Heat aging at 160o
C, compression molding, thickness 1 mm.
It should be noted that systems based on thioethers are not appropriate for use in combination with HALS
for light stabilized applications due to interactions between the components. In these cases alternative
systems based on combinations of HALS and phenolic antioxidants can be employed (Figure 6).
Figure 6. Long-Term Thermal Stabilization of PP Homopolymer.
Compression molding, thickness 2 mm.
All formulations contain 0.05% AO-1 + 0.1% P-1 + 0.05% calcium stearate.
Data from Reference [2]

12
High molecular weight HALS are known contribute to the thermal oxidative stability of
polypropylene,[2] particularly at lower temperatures (<120o
C, Figure 6). However, at higher
temperatures antagonistic interactions between HALS and phenolic antioxidants (especially AO-1) are
observed with some HALS (e.g. HALS-4). As a result of such interactions, the long-term thermal
stability of the HALS/AO combination may in some cases be lower than when the AO is used alone. The
tertiary amine HALS-5 is particularly noteworthy in terms of its strong contribution to long-term heat
stability as well as its lack of interaction with phenolic antioxidants (Figures 6 & 7). Systems based on
combinations of hindered phenols (especially AO-1 or AO-3) with HALS-5 are ideal for applications in
which both long-term thermal stability and light stability are required. Systems based on HALS-5 also
provide excellent long-term thermal stability in talc-filled substrates and in formulations containing
carbon black, in some cases outperforming conventional systems based on hindered phenols in
combination with thioethers.
Figure 7. Long-Term Thermal Stabilization of PP Homopolymer.
Injection molding, thickness 1.6 mm.
All formulations contain 0.1% AO-3 + 0.1% P-1 + 0.2% HALS-1 + 0.1% calcium stearate.
Data provided courtesy of Sabo S.p.A. and used with permission.
Light Stabilization
Exposure of PP and TPO parts to ultraviolet radiation (naturally present in sunlight) initiates degradation
through a photo-oxidative process. In polypropylene this process takes place predominately in the
amorphous phase of the polymer due to the higher solubility of oxygen there as compared to the
crystalline phase. Degradation as a function of depth has been studied.[3] In unstabilized polypropylene,
oxidation takes place most rapidly at the surface of the part. In stabilized polymers, the extent of
oxidation is much reduced but is still observed even deep within the part (> 1 mm below the surface).
Photo-oxidation of the polymer is accompanied by an increase in crystallinity due to a process known as
chemi-crystallization.[20] When chain scission takes place during photo-oxidation, polymer chains in the
amorphous phase are freed from some of their entanglements and can achieve sufficient mobility to
crystallize. It is not clear whether crystallization takes place by formation of new crystals or by addition
to existing ones. In any case, chemi-crystallization results in the formation of voids that manifest as
surface micro-cracks. These eventually grow large enough to be seen with the naked eye. The increased
roughness of the cracked surface also scatters light, which in turn results in a loss of gloss (and

13
subsequently chalking) and changes in the perceived color of the part, particularly in pigmented materials.
Formation of surface cracks is also a key factor in the embrittlement of polypropylene.
The resistance of a material to the effects of weathering is typically determined by measuring changes in
the appearance or mechanical properties of a test specimen resulting from natural or accelerated
weathering. Changes in appearance are most often assessed using instrumentation such as a
spectrophotometer or a gloss-meter. In some cases changes can be assessed visually (e.g. onset of
chalking) or microscopically (e.g. the formation of micro-cracks). Alternatively the weatherability of a
material can be assessed by measuring changes in a mechanical property such as elongation at break,
tensile strength, or impact strength as a function of exposure time.
Natural outdoor weathering is a slow process, even when conducted in tropical or desert climates with
relatively high solar irradiance and temperature. Accelerated weathering devices (often referred to as
weatherometers or WOM) have been developed to provide results more quickly. These devices provide
faster results than natural weathering because they can be operated continuously (i.e. samples can be
exposed for 24 hours per day rather than only during daylight hours) and also because the lamps used as
radiation sources provide more intense radiation than natural sunlight. They also have the advantage that
the total amount of radiation received by the sample can be carefully controlled and accurately measured.
The most widely used weatherometers today utilize xenon-arc lamps as the radiation source, which when
properly filtered produce a spectrum of radiation that is comparable to that of natural sunlight albeit more
intense. Accelerated weathering methods utilizing xenon-arc weatherometers are described and specified
in industry standards such as SAE J2412 (for automotive interior trim components), SAE J2527 (for
automotive exterior materials), ISO 4892, and ASTM G155.
Systems based on hindered amine light stabilizers (HALS), alone or in combination with other additives
(especially benzoates and UV absorbers) represent the state of the art for the light stabilization of
polypropylene and TPO.[21]
The effects of molecular weight on HALS diffusion in polyolefin matrices are well documented, as well
as the importance of diffusion in the stabilization of polypropylene.[22-24] Since the regenerative
mechanism of HALS is less efficient in polypropylene than in other polyolefins,[14] over the lifetime of a
part deactivation of the stabilizer can occur, especially near the surface. In thick section parts containing
low molecular weight HALS (HALS-1, HALS-2), the stabilizer content at or near the surface can be
replenished by diffusion of the additives from the deeper layers of the part. Replenishment is also
possible for medium molecular weight HALS (HALS-3), albeit at a slower rate. For high molecular
weight polymeric HALS diffusion is usually negligible and there is no replenishment mechanism. Thus
the low- to medium-molecular weight HALS tend to give better protection in thick section polypropylene
and TPO applications than high molecular weight HALS. However, for thin-section applications like
fibers and films the replenishment mechanism is less important and high molecular weight HALS
(HALS-4 and HALS-5) are favored due to their resistance to migration and loss by volatilization.
Combinations of hindered amines are well known in the art and are widely used.[25] In thick-section
polypropylene applications, combinations of the low-molecular weight HALS-1 and the high-molecular
weight HALS-4 have been shown to provide somewhat better performance than would be expected based
on the performance of the individual components (Figure 8). Systems based on the high molecular
weight HALS-5 are especially useful for the stabilization of mineral-filled substrates (Figure 9), and as
previously mentioned also provide excellent long-term thermal stability.
The use of systems based on HALS alone (e.g. HALS-1 or HALS-2 alone, or their combinations with
HALS-4 or HALS-5) is often sufficient to provide adequate weatherability to polypropylene and TPO.
However, for some applications such as automotive exterior materials, further improvements in
weatherability may be required. In these cases the performance of HALS can be enhanced by use in
combination with other additives such as benzoates and UV absorbers.[21]

14
Figure 8. Light Stabilization of Polypropylene Homopolymer.
Outdoor weathering in Florida, injection molding, 2 mm thickness
* Failure defined as < 50% retention of impact strength.
Figure 9. Light Stabilization of Calcium Carbonate Filled Polypropylene Homopolymer.
Accelerated weathering, xenon arc weather-o-meter, 0.35 W/m2
(340 nm)
Injection molding, thickness 2 mm
25% CaCO3, 1% TiO2, base stabilization 0.033% AO-1 + 0.067% P-1
Data provided courtesy of Sabo S.p.A. and used with permission.

15
The synergy between benzoates and HALS in the stabilization of polypropylene has been known for some
time.[26-28] As shown in Figure 10, the combination of HALS-2 with B-2 clearly gives better light
stability than HALS-2 used alone. Synergistic behavior is also known for combinations of other HALS
with either B-1 or B-2. The synergistic performance suggests that the benzoates may be more effective
scavengers of certain types of free radicals involved in the degradation process than are HALS.
Figure 10. Light Stabilization of Black Reactor TPO.
Accelerated weathering, xenon arc weather-o-meter, SAE J1885 (auto exterior cycle).
It has also been reported that like benzoates, the conventional hindered phenol AO-2 exhibits a synergy
with HALS,[29,30] unlike the similar antioxidant AO-1 (Figures 11 & 12). This effect is not surprising
given that an early mechanistic study found AO-2 to provide performance comparable to the benzoate B-
2 for the stabilization of polypropylene films.[15] The positive effect for AO-2 as compared to AO-1 is
possibly linked to the ability of the lower molecular weight AO-2 to migrate to layers near the surface
where photo-degradation is occurring.[29-31]
Systems based on combinations of HALS with UV absorbers are also sometimes used for the stabilization
of polypropylene and TPO. Because the screening effect of UV absorbers is directly dependent on the
path length, they provide little or no protection at or near the surface of a part, where the path length is
very short. However, for the deeper layers (> 1 mm below the surface) of thick section parts, all of the
UV radiation can be blocked with incorporation of ~0.1% UV absorber and photo-degradation in these
deeper layers is effectively prevented. This effect may serve to improve retention of mechanical
properties after exposure. As illustrated in Figure 13, the combinations of HALS and UV absorbers
provide some improvement in physical property retention in polypropylene after exposure but no
improvement in surface protection (exposure time to cracking) as compared to HALS used alone.
UV absorbers can also improve surface protection indirectly if other stabilizers are able to migrate from
the protected deeper layers to the layers closer to the surface in which photodegradation is taking
place.[31]

16
Figure 11. Light Stabilization of Polypropylene
Homopolymer. Effect of Phenolic Antioxidant.
Accelerated weathering (carbon arc).
Figure 12. Light Stabilization of Pigmented (Dark-
Gray) High Impact Propylene/Ethylene
Copolymer (14% Ethylene).
Effect of Phenolic Antioxidant.
Accelerated weathering (xenon arc, ASTM G26).
Injection Molding, 3.2 mm thickness.
Figure 13. Light Stabilization of PP Homopolymer: Effect of UV Absorbers.
Accelerated weathering (Ultra-Vitalux lamps), injection molding, 1 mm thickness.
* Failure defined as < 50% retention of tensile strength.
> >

17
Other formulation components such as pigments can also perform the function of blocking the penetration
of UV radiation. In this situation the UV absorbers would not be expected to be effective as light
stabilizer synergists. Generally the benefits of using a UV absorber are most prominent in natural and
lightly pigmented parts. However, in the case of some organic pigments with limited lightfastness the use
of UV absorbers as part of the formulation can be beneficial.[9] Here the UV absorber may be acting to
improve the lightfastness of the organic pigments by quenching of their excited states or by another
unknown mechanism.
Synergistic combinations of HALS, benzoates, and UV absorbers have also been reported.[33,34] To
understand the reason for this three-component synergy, one has to consider that benzoates (unlike
HALS) do absorb short-wavelength UV radiation (λ < 300 nm) and are vulnerable to photo-degradation
themselves. Since the incorporation of a UV absorber into the formulation prevents photo-degradation at
the deeper levels of the part, low molecular weight additives such as B-1, B-2, and AO-2 are able to
migrate from these protected deeper layers to layers closer to the surface in which photo-degradation is
taking place.[31]
Common Problems Associated with Stabilizer Additives
While the use of stabilizer additives is essential to protect polypropylene and TPO during processing and
end-use, they can give rise to unanticipated problems during part manufacturing or end use. Potential
pitfalls include problems associated with migration (such as blooming and fogging), unexpected
discoloration (warehouse discoloration or gas fading), and interactions with automotive coatings.
Through proper selection of the additives, these problems can largely be avoided.
Blooming and Fogging
Excessive migration of additives is associated with problems such as blooming and fogging. Blooming
(or exudation) of additives on part surfaces can be a problem after storage, and sometimes during end use.
Low molecular weight additives can migrate to the surface of part where they crystallize as a separate
phase, forming the powdery or chalky deposit on the surface commonly referred to as bloom.[35]
Additives present in these surface deposits can often be identified using FT-IR spectroscopy.
In particular, the problem of blooming is known to be associated with the low molecular weight HALS-
1,[28,36] which is thought to be due to its high diffusivity and relatively low solubility in polyolefin
substrates. Besides being unsightly, exudates containing HALS-1 can present a safety concern due to its
known skin irritation and sensitization effects. This problem can be easily eliminated by substitution of a
more soluble low molecular weight HALS such as HALS-2.
Fogging is the condensation of volatile materials on the windshield, which originate from interior
components. The tendency of plastic additives to contribute to this phenomenon is related to both the
inherent volatility of the additive and its compatibility with the polymer matrix. The fogging behavior of
plastics is assessed using standard test methods such as SAE J1756 in which polymer pellets are heated
and volatile components collected on a cooled cover plate. HALS-1 has been found to be associated with
automotive fogging.[36] As in the case of blooming, it is expected that this problem can be reduced by
substitution of a more compatible low molecular weight HALS such as HALS-2 or a non-migratory high
molecular weight HALS.
Warehouse Discoloration or Gas Fading
Oxidation products formed from hindered phenols can produce discoloration in plastic parts.[16] For
example, a pink or yellowish discoloration is sometimes observed when parts are exposed to nitrogen
oxides (NOx, formed during combustion of natural gas) during storage, which is referred to as “gas-

18
fading” or “warehouse discoloration”.[9] This phenomenon is a particular problem in natural or light-
colored parts, and appears most frequently in the winter due to the use of natural gas heaters and less
efficient ventilation. The problem can also be aggravated by the presence of HALS in the formulation,
especially secondary amine types such as HALS-1, HALS-2, and HALS-4.
The resistance of a material to this type of discoloration is typically assessed by exposing parts to
controlled levels of NOx in an atmospheric fume chamber operated according to a test method such as
AATCC 23. Color change in the parts is measured using a spectrophotometer as a function of exposure
time.
Hindered phenols AO-1 and AO-2 are particularly prone to this problem, but as shown in Figure 14, other
products can be substituted (AO-3, AO-4) that are non-discoloring under these conditions.[18] The
partially hindered phenol AO-5 has also been reported to have excellent resistance to gas fade
discoloration.[37] Processing stabilizer systems based on hydroxylamines are also inherently non-
discoloring and can be used when long-term thermal stability requirements are modest.
Figure 14. Gas Fade Discoloration in LLDPE.
All formulations contain 0.15% HALS
Coating Adhesion
Many HALS are strongly basic, and this can lead to undesired interactions with acid-catalyzed thermoset
acrylic automotive coatings used on TPO exterior parts.[9,36,38]. These interactions lead to effects such
as incomplete cure of the coating and reduced adhesion between the coating and the plastic substrate. The
interaction of low molecular weight, basic HALS (especially HALS-1, and possibly HALS-2 as well) can
be particularly problematic.
The effects of HALS on coating adhesion are assessed by tests on painted plastic panels containing
HALS. Abrasion tests on the painted panels (e.g. Taber Scuff, GM 9911P) give an indication of effects
on coating cure, while tape peel tests (with or without crosshatch scoring of test specimens) are used to
investigate adhesion between the substrate and coating.
For paintable applications, systems based on high molecular weight HALS in combination with non-basic
NOR HALS have been developed and give good results.[9,38] Alternatively, systems based on

19
combinations of benzoates with high molecular weight HALS (especially HALS-5) would also be
expected to be non-interacting and also to provide excellent weatherability performance.
Conclusions
Polypropylene degrades when exposed to heat or light by an oxidative mechanism in which chain scission
predominates. Oxidative degradation leads to a number of undesirable effects that compromise the useful
life of the polymer.
Stabilizer additives are very effective for improving the stability of polypropylene and TPO to heat and/or
light induced degradation. Most of these products act by scavenging the radical and peroxide
intermediates in the oxidation process. Examples of commonly used stabilizer additives include hindered
phenols, phosphites and phosphonites, thioethers, hydroxylamines, hindered amine light stabilizers
(HALS), benzoates, and UV absorbers.
Degradation during melt processing results in melt flow shifts and discoloration. Combinations of
hindered phenols and phosphites represent the state of the art for the stabilization of polypropylene and
TPO under these conditions. Systems incorporating partially-hindered phenols (e.g. AO-4) and/or high
performance phosphites (e.g. P-2, P-3, P-4) provide the highest level of performance in terms of melt
stability.
Exposure to heat during end use in the solid phase eventually results in a loss of useful mechanical
properties as well as discoloration. Systems based on combinations of hindered phenols and either
thioethers or HALS (especially HALS-5) can significantly extend the useful life of polypropylene and
TPO under these conditions. Systems based on HALS-5 in combination with hindered phenols are most
suitable for use in applications where light stability is also required.
Light-induced degradation results in changes in appearance and a loss of mechanical properties. Systems
based on HALS represent the state of the art for the light stabilization of polypropylene and TPO. When
higher performance is needed, improvements can often be achieved by using synergistic combinations of
HALS with other additives such as benzoates, ultraviolet absorbers, and some phenolic antioxidants
(especially AO-2).
Stabilizer additives can sometimes give rise to unexpected, undesired effects such as blooming,
automotive fogging, warehouse discoloration (gas fading), and interactions with automotive coatings.
Through the proper selection of additives, these problems can largely be avoided.
References
1. Bolland, J., & Gee, G., Trans. Faraday Soc., 1946, 42, 236-243.
2. Schwarzenbach, K. et al., in “Plastics Additives Handbook”, 5th ed., H. Zweifel, Ed., Hanser
Publishers, Munich, 2001, Ch. 1.
3. White, J., Shyichuk, A., Turton, T., Syrotynska, I., Poly. Deg. and Stab., 2006, 91, 1755-1760.
4. Pospisil, J., in Developments in Polymer Stabilisation, G. Scott, Ed., Elsevier, 1979, Vol. 1, Ch. 1.
5. Denney, D., Goodyear, W., Goldstein, B., J. Am. Chem. Soc., 1960, 82, 1393-1395.
6. Armstrong, C., Husbands, M., Scott, G., Eur. Poly. J., 1979, 15, 241-248.
7. Kikkawa, K., Poly. Deg. and Stab., 1987, 18, 237-245.
8. Yagi, M., Nishina, T., Sugibuchi, K., U.S. Patent No. 5,081,170, January 14, 1992.

20
9. Botkin, J., Solera, P., “Stabilizer Selection Guidelines for Automotive TPO Applications”, presented
at the Society of Plastics Engineers Global Automotive TPO Conference, Dearborn, MI, October
2001.
10. Botkin, J., Stadler, U., U.S. Patent No. 7,291,669 B2, November 6, 2007.
11. Klemchuk, P. P., Gande, M. E., Poly. Deg. and Stab., 1988, 22, 241-74.
12. Allen, N. S., Chirinis-Padron, A., Henman, T. J., Poly. Deg. and Stab. 1985, 13, 31-76.
13. Shilov, Yu. B., Battalova, R. M., Denisov, E. T., Doklady Akademii Nauk, SSSR, 1972, 207, 388.
14. Gryn’ova, G., Ingold, K., Coote, M., J. Am. Chem. Soc., Articles ASAP (As Soon As Publishable),
Publication Date (Web): April 11, 2012 (Article), DOI: 10.1021/ja3006379.
15. Allen, N., Parkinson, A., Loffelman, F., Susi, P., Poly. Deg. and Stab., 1983, 5, 241-266.
16. Klemchuk, P., Horng, P.-L., Poly. Deg. and Stab., 1991, 34, 333-346.
17. Gugumus, F., in “Plastics Additives”, 3th
ed., Gachter, R., Muller, H., Eds., Hanser Publishers,
Munich, 1990, Ch. 1.
18. Vulic, I., Vitarelli, G., Zenner, J., Macromol. Symp., 2001, 176, 1-15.
19. Yachigo, S., Sasaki, M., Kojima, F., Poly. Deg. and Stab., 1992, 35, 105-113.
20. White, J., Rabello, M., Polymer, 1997, 38, 6379-6387.
21. Botkin, J., “Light Stabilization of Polypropylene: An Independent Perspective,” presented at the
Society of Plastics Engineers International Polyolefins Conference, Houston, TX, February 2007.
22. Malik, J., Hrvik, A., Tomova, E., Poly. Deg. and Stab., 1992, 35, 61-66.
23. Gugumus, F., Poly. Deg. and Stab., 1999, 66, 133-147.
24. Tobita, E., Fukushima, M., Funamizu, T., Zingde, G., Goman, P., “Effect of HALS on Stabilization
of Filled and Pigmented Polypropylene”, presented at the SPE Global Automotive TPO Conference,
Dearborn, Michigan, October 2003.
25. Gugumus, F., Poly. Deg. and Stab., 2002, 75, 295-308.
26. Mathis, R., U.S. Patent No. 4,035,323, July 12, 1977.
27. Nagasaki, H., Yachigo, S., Takata, T., Yamamoto, H., Takahashi, Y., U.S. Patent No. 4,985,479,
January 15, 1991.
28. Davis, L., Zenner, J., Stretanski, J., “Extending the Useful Lifetime of Pigmented PP and TPO”, SPE
International Polyolefins Conference 2006, Houston, March 2006.
29. Kikkawa, K., Poly. Deg. and Stab., 1995, 49, 135-143.
30. Gijsman, P., Sampers, J., Bunge, W., Vaassen, J., U.S. Patent Application publication 2005/0085574
A1, April 21, 2005.
31. Shlyapintokh, V., Pure and Appl. Chem., 1983, 55, 1661-1668.
32. Disteldorf, J., Haage, H.-J., Libera, H., U.S. Patent No. 4,986,932, January 22, 1991.
33. Yamamoto, M., Shimada, M., Yamazaki, S., Kanai, T., Sei, K., U.S. Patent No. 4,467,061, August
21, 1984.
34. Stretanski, J., Sanders, B., U.S. Patent No. 6,843,939, January 18, 2005.
35. Calvert, P., Billingham, M., J. Appl. Poly. Sci., 1979, 24, 357-370.

21
36. Goldstein, S., Coughlin, G., “Recent Advances in UV Stabilization Systems for Automotive TPO’s”,
presented at the SPE Automotive TPO Global Conference, Sterling Heights, Michigan, October 2007.
37. Yachigo, S., Sasaki, M., Ishii, T., Tanaka, S., Poly. Deg. and Stab., 1992, 37, 99-106.
38. Lau, E., Edge, D., U.S. Patent No. 5,733,956, March 31, 1998.

22
Appendix: Some Commercially Available Stabilizer Additives
Chemical Structure CASRN
AO-1
O
OO
O
O
O
O
OH
OH
OH
OH
O
6683-19-8
AO-2
OH
O
O
C18
H37
2082-79-3
AO-3
N
N
N
OH
OH
OH
O
OO
27626-62-6

23
AO-4
N
N
N
CH2
CH2
CH2
OH
CH3
CH3
O
OH
CH3
CH3
O
OH
CH3CH3
O
40601-76-1
AO-5
OH
O
O
O
O
O
O O
O
CH3
CH3
CH3
CH3
CH3
OH
CH3
90498-90-1
P-1
O
P
O
O
31570-04-4
P-2
O P
O
O
O
O
P O
26741-53-7
P-3
O P
O
O
O
O
P OCH3 CH3
80693-00-1

24
P-4
PP
O
O
O
O
119345-01-6
TS-1
S
O
O C18
H37OH37
C18
O 693-36-7
TS-2
O
O
O
O
S
S
C12
H25
C12
H25
O
O
O
O
S
SH25
C12
H25
C12
29598-76-3
H-1 R
N
OH
R
R = C14-18
143925-92-2
H-2
N
OH
621-07-8
H-3
N
+
R
R
CH3
O R = C14-24
204933-93-7
HALS-1
O
O
O
O N
H
N
H
52829-07-9
HALS-2
R = C11-20
predominantly C16-18N
O
O
R
H
167078-06-0

25
HALS-3
O
O
O
O
N
CH3
N
CH3
OO
N
CH3
O O
N
CH3
91788-83-9
HALS-4
N
N (CH2)6
N
N
N
NN
NH
N
N
(CH2)6 N H
N
H
C8H17
HHHH
n
71878-19-8
70624-18-9
HALS-5
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NBu
Bu
H
N
Bu
N
Bu N
CH3
N
CH3
NCH3
N Bu
N
CH3
N
Bu
N
Bu
N CH3
N
CH3
N
CH3
H
N
Bu
N
CH3
106990-43-6
UVA-1 O OH
O
C8
H17
1843-05-6

26
UVA-2
N
N
N OH
25973-55-1
UVA-3
N
N
N OH
CH3
Cl
3896-11-5
UVA-4
N N
N
OH
O
C8
H17
CH3
CH3
CH3
CH3 2725-22-6
B-1
OH
O
O
4221-80-1
B-2
OH
O
O
C16H33
67845-93-6

The Stabilization of Polypropylene and TPO: An Overview

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Was ist angesagt?

Was ist angesagt? (20)

Ähnlich wie The Stabilization of Polypropylene and TPO: An Overview

Ähnlich wie The Stabilization of Polypropylene and TPO: An Overview (20)

Mehr von Jim Botkin

Mehr von Jim Botkin (9)

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

The Stabilization of Polypropylene and TPO: An Overview