A 0.521 v fast lock in adpll for supporting dynamic voltage and frequency scaling

ONLINE IEEE PROJECTS IeeeXpert.com
BUY THIS PROJECT FOR 2000 RS –IeeeXpert.com
Mobile: +91-9566492473/+91-9042092473| WhatsApp: 09566492473
Email: contact@ieeexpert.com | Locations: Pondicherry/Chennai
Delivering Projects all over India | 100% Output Satisfaction (or) Get Money back
A 0.52/1 V Fast Lock-in ADPLL for Supporting
Dynamic Voltage and Frequency Scaling
Abstract:
In energy-efficient processing platforms, such as wearable sensors and implantable medical
devices, dynamic voltage and frequency scaling allows optimizing the energy efficiency under
various modes of operation. The clock generator used in these platforms should be capable of
achieving a faster settling time and has a wider operating voltage range. In this brief, a fast lock-
in all-digital phase-locked loop (ADPLL) with two operation modes (0.52/1 V) is presented. The
proposed ADPLL can quickly compute the desired digitally controlled oscillator control code
with high accuracy. Therefore, the proposed ADPLL can achieve a fast setting time with
frequency errors <5% within four clock cycles. The proposed ADPLL is implemented using a
standard performance 90-nm CMOS process. The output frequency of the ADPLL ranges from
60 to 600 MHz at 1 V, and from 30 to 120 MHz at 0.52 V. The proposed architecture of this
paper analysis the logic size, area and power consumption using Xilinx 14.2.
Enhancement of the project:
Existing System:
For smart sensing applications, low cost and low power consumption are important. Hence, all-
digital PLLs (ADPLLs) are more suitable than analog PLLs, because voltage control schemes
face several design challenges in advanced CMOS process at low supply voltages; further, the
frequency range for smart sensing applications( < 100MHz) can be easily covered by ADPLLs
without necessitating forward body-biased or bulk-driven techniques.
In current ADPLL architectures, the binary search algorithm, gear-shifting mechanism, and
modified bang–bang algorithm have been proposed for reducing the lock-in time. However,
several tens of reference clock cycles are still required to achieve lock-in. A DCO control code

Mobile: +91-9566492473/+91-9042092473| WhatsApp: 09566492473
estimating algorithm has been proposed. However, the proposed algorithm requires the DCO
resolution. A frequency estimation algorithm that employs the period ratio between the reference
clock and the DCO output clock to compute the desired DCO control code for generating the
target frequency within two cycles has been proposed. However, the period ratio computed by
the frequency counter is an integer number. Therefore, to reduce the frequency error induced by
quantization for the period ratio calculation, the multiplication ratio of the ADPLL needs to be
maintained at >45.
Disadvantages:
 power consumption is high
Proposed System:
Fig. 1 shows the block diagram of the proposed ADPLL. The ADPLL is composed of a phase
and frequency detector (PFD), an ADPLL controller, a digital loop filter, a cyclic time-to-digital
converter (TDC)-embedded DCO, a frequency finder, and a frequency divider.

Mobile: +91-9566492473/+91-9042092473| WhatsApp: 09566492473
Fig. 1. Block diagram of the proposed ADPLL.
The proposed cyclic TDC-embedded DCO uses an interpolatorbased fine-tuning stage [18] to
maintain a monotonic response between the DCO control code and the output frequency under
process, voltage, and temperature (PVT) variations. In addition, the proposed cyclic TDC-
embedded DCO can compute the period ratio between the reference clock (REF_CLK) and the
DCO output clock (OUT_CLK) as a fixed-point number to reduce the quantization error in the
frequency estimation algorithm.
CIRCUIT IMPLEMENTATION
Fig. 2. Proposed cyclic-TDC-embedded DCO.
Fig. 2 shows the circuit diagram of the proposed cyclic TDC-embedded DCO, which is
composed of a coarse-tuning stage, a fine-tuning stage, and an embedded cyclic TDC for
computing the period ratios (Rmax and Rmin). The coarse-tuning stage of the DCO consists of
64 coarse-tuning delay cells (CDCs), and the coarse-tuning step is the delay time of two NAND
gates. The cyclic TDC is composed of 65 pulse-latch DFFs at the output node of the NAND

Mobile: +91-9566492473/+91-9042092473| WhatsApp: 09566492473
gates, a cyclic counter, and a TDC encoder. The TDC resolution is equal to the delay time of two
NAND gates or the coarse-tuning resolution of the DCO. The DCO_Decoder decodes the binary
11-bit DCO_code[10:0] into the coarse-tuning and fine-tuning thermometer codes. The
TDC_Encoder encodes the 65-bit thermometer code sampled by the pulse-latch DFFs into a 7-bit
TDC fractional number (TDC_Frac[6:0]) and the cyclic counter outputs a 9-bit TDC integer
number (TDC_Int[8:0]).
The fine-tuning stage of the DCO [18] is composed of two parallelly connected tristate buffer
arrays operating as an interpolator. By adjusting the number of turned-ON tristate buffers in the
arrays, the resolution of the fine-tuning stage can be enhanced to 1/32 that of the coarse-tuning
step. The proposed ADPLL uses a cyclic TDC-embedded DCO to compute the fixed-point
values of Rmax and Rmin for calculating the target DCO control code (init_code).
Advantages:
 Reduce the power consumption
Software implementation:
 Modelsim
 Xilinx ISE

A 0.521 v fast lock in adpll for supporting dynamic voltage and frequency scaling

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

Empfohlen

Empfohlen (20)

A 0.521 v fast lock in adpll for supporting dynamic voltage and frequency scaling