Hart Protocol Introduction

HART Protocol Introduction
ICP DAS USA, Inc.
sales@icpdas-usa.com
1-310-517-9888 x105
www.icpdas-usa.com
Making Data Acquisition Easy
HART Introduction| 6/17/15

HART IntroductionHART (Highway Addressable Remote Transducer) :
The HART protocol was developed in the mid-1980s by Rosemount Inc.
for use with smart measuring instruments. The registered trademark and all
rights in the protocol were transferred to the HART Communication
Foundation (HCF). The protocol remains open and free for all to use without
royalties.
Features：
 Communicates at 1200 bps.
 Support 4-20mA analog signal (primary measured value) and
digital signal (device information).
 Support point-to-point or multi-drop network. (Max. 15 devices)
 Support 2 wire (Bus Powered) or 4 wire (device ).
 HART is a master/slave protocol (up to two masters).
 HART Instrument with intrinsically safe explosion-proof.

Comm. Structure (1/2)
Peer-to-Peer mode (analog/digital)

HART Wiring (Peer to Peer)

Comm. Structure (2/2)
Multi-drop mode (digital)

HART Wiring (Multi-drop)

Type Model Module Function State
Converter
I-7567 USB to HART Release
I-7570 RS-232/422/485 to HART Release
I-7547 Ethernet to HART Release
HRT-228 HART to AO (4 ch.) 2015/Q4
Gateway
HRT-710 Modbus(RTU/ASCII) to HART Release
HRT-711 Modbus/TCP to HART Release
GW-7557 PROFIBUS DP to HART Release
HRT-710-S Modbus(RTU/ASCII) to
HART Slave
2016/Q1
HRT-711-S Modbus/TCP to HART Slave 2016/Q1
I/O Module
I-87H17W HART Analog Input (8 ch.) Release
I-87H24W HART Analog Output (8 ch.) 2016/Q1
ICP DAS HART Products
HART Products

I-7567 (1/3)
Features：
 Support USB1.1 or USB2.0
 No external power supply (by USB)
 Support point-to-point / multi-drop
 Support firmware update via USB
 Selectable 250Ω load resistor
 Support HART Short/Long frame
 Support HART Burst mode
 Provide PWR / Tx / Rx LED
 Built-in Watchdog
Click here to learn more

I-7567 (2/3)
Application Structure

I-7567 (3/3)
HC_Tool:
1. Auto scan all HART devices and
show the HART device information.
2. Provide HART Universal and
Common-Practice command for
configuration of HART devices easily.
3. Data logging for HART comm.

I-7570 (1/3)
Features：
 Provide RS-232/422/485 Interface
 Support firmware update via RS-232

I-7570 (2/3)

I-7570 (3/3)
HC_Tool:

I-7547 (1/3)
Features：
 Support Ethernet Interface with
VxComm technique.
 Support firmware update via Ethernet
 Provide four HART channels
 Provide PWR / TxRx LED

I-7547 (2/3)

I-7547 (3/3)
HC_Tool:

FDT / DTM Support

HART OPC Server Support

HRT-710 (1/3)
Features：
Support Modbus RTU/ASCII
 Provide RS-232/422/485 Interface
Support on-line replacement of HART
devices (FW_v1.5)

HART-710 (2/3)

HART-710 (3/3)
HG_Tool :
1. Auto scan all HART devices
and show the device information.
2. Provide module configuration
and HART communication
easily and quickly.
3. Modbus Address Mapping
Table Configuration.
4. Provide the diagnostic info. of
HRT-710 and HART device.
5. Provide “Load/Save” module
configuration file to apply to
other HRT-710 quickly.

HRT-710 Application

HRT-710 FAQ
1. How to integrate HART device information to SCADA or HMI ?
(1) Refer to the ”Q01”, “Q02” and “ Q03” of HRT-710 FAQ.
(http://www.icpdas.com/products/Remote_IO/can_bus/faqs.htm#HART)
2. How to update the firmware of HRT-710 ?
(1) Refer to the ”Q04” of HRT-710 FAQ.

HRT-711 (1/3)
Features：
Support Modbus TCP
 Provide Ethernet Interface
 Provide LED indicators
Support on-line replacement of HART

HART-711 (2/3)

HART-711 (3/3)
easily and quickly.
3. Modbus Address Mapping
Table Configuration.
4. Provide the diagnostic info. of
HRT-711 and HART device.
configuration file to apply to
other HRT-711 quickly.
HRT-711 Utility

Modbus to HART Software Integration

GW-7557 (1/2)
Features：
 Support PROFIBUS DP-V0
 Auto Detect PROFIBUS Baudrate
 Support PROFIBUS Max. Baud 12Mbps
 Max Output / Input Length 240 Bytes
 Provide four HART channels
 Support two HART master
 Provide PWR / RUN / ERR LED

GW-7557 (2/2)

GW-7557 (3/3)
PH_Tool :
easily and quickly.
3. Provide PROFIBUS parameter
setting info.
configuration file to apply to other
GW-7557 quickly.

I-87H17W (1/2)
Features：
 Support WinPAC / ViewPAC /
XPAC and I-87Kn / RU-87Pn /
USB-87Pn / ET-87Pn series.
 Provide 8 HART channels.
 Support current measurement
and HART communication.
 Support point-to-point only.
 Support 2 or 4 wire HART device.
 Open wire detection for every ch.
 Built-in Dual Watchdog
 Support DCON protocol and utility
 Provide PWR and Ch. LED

I-87H17W (2/2)

I-87H24W (1/2)
Features：
 Support WinPAC / ViewPAC /
XPAC and I-87Kn / RU-87Pn /
USB-87Pn / ET-87Pn series.
 Provide 4 HART channels.
 Support current output
and HART communication.
 Support point-to-point only.
 Support 2 or 4 wire HART device.
 Open wire detection for every ch.
 Built-in Dual Watchdog
 Support DCON protocol and utility
 Provide PWR and Ch. LED

I-87H24W (2/2)

HART I/O Application
Gas Pipeline Pressure Monitor System

ICP DAS HART Application

HART Resource
1. ICP DAS USA HART Products:
http://www.icpdas-usa.com/hart_gateways.html
2. HART Official Website:
http://www.hartcomm.org/index.html

Questions?
• Please ask any questions you may have.
• Contact us:
Tel: +1 (310) 517-9888 +1 888-971-9888
Website: www.icpdas-usa.com
Email: sales@icpdas-usa.com
Follow ICP DAS USA On:
Earthquake Monitoring System| Maria Lemone | 4/3/15

Hart Protocol Introduction

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Was ist angesagt?

Was ist angesagt? (20)

Andere mochten auch

Andere mochten auch (16)

Ähnlich wie Hart Protocol Introduction

Ähnlich wie Hart Protocol Introduction (20)

Mehr von ICP DAS USA, Inc.

Mehr von ICP DAS USA, Inc. (20)

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

Hart Protocol Introduction