Gyptone edge d1 installation manual

Design and technique
Product description
Gyptone edge D1 is a pre-painted, de-
mountable suspended acoustic ceiling,
mounted in a concealed grid system (T-24).
Gyptone ceilings can be used for many
applications, like schools, offices and com-
mercial settings. Gyptone edge D1 is fully
demountable and gives good opportuni-
ties for inspection in the cavity above the
ceiling. Gyptone edge D1 is available with
perforated and non- perforated surfaces.
Thickness is 12,5 mm and the format
600 x 600 mm.
Plenum height
Min and max plenum heights with T-grid
system can be found on page 5.
Surfaces
Gyptone ceiling tiles with edge D1 is paint-
ed from the factory. The color used is white
(NCS0500) with a gloss value of 5-9 accord-
ing to ISO 2813. Further painting is to be
done with a shorthaired paint roller as
spray painting will impair the acoustic
performance.
Grid system
Gyptone edge D1 is installed on a Quick-
Lock T-24 grid system. The system is sus-
pended and should be installed with
suitable hangers. Gyptone edge D1 must
be installed according to this installation
manual as well as the general specifica-
tion of the project.
Fire resistance
A2-s1, d0.
Load
The max point load for each tile, with a
deflection of max 2 mm is 1 kg. If higher
load is needed the installations needs
to be fixed to the slab above with dedi-
cated suspensions. Max point load for the
grid is 0,5 kg. Max load equally spread on
the main beams is 2 kg/m for T24 grid
system.
Stability
Gyptone edge D1 is to be installed and
used in rooms with relative humidity not
permanently exceeding 70% or tempera-
tures exceeding 45 degrees Celsius.
Weight
Non perforated Gyptone edge D1 = 9 kg/m²
Perforated Gyptone edge D1 = 8 kg/m²
Cleaning
Can be cleaned with a damp cloth. Do not
use detergents. Always use clean gloves
when installing Gyptone edge D1.
Maintenance
If damages on edges or surfaces occurs,
It is recommended to replace the
damaged tile.
Gyptone edge D1™ system
Installation manual
GyprocA/Sisnottobeheldresponsibleforanytypographicalerrorsandreservestherighttochangerangeandproducttechnologywithoutpriornotice.

Gyptone edge D1 – Installation manual 2
The placement of the wall angle is marked with a bubble level/
chalk line and mounted with a flat headed screw suitable for
the wall per max. 300 mm. The first screw should be no more
than 50 mm from a corner. The wall angles should not be
shorter than 300 mm. Cut the wall angles in close mitre at the
corner joints. If the wall is uneven, mount a thin wooden list
behind the wall angle.
Hangers for the main beam are placed in rows per 600 mm.
The first main beam 200 - 600 mm from the wall. First hanger
in main beam max 100 mm from the wall. Other hangers per
max 1200 mm. See illustration on page 4. The hook of the
hanger must be squeezed together with a pair of nippers.
Installation of T-grid system
We recommend reading the manual thoroughly prior to installing the ceiling
When mounting the cross tees, always place the hook in the
right side of the slot seen from the mounting side. Cross tees
are mounted at each 1200 mm, see illustration on page 4. The
cross tee is placed by the first hanger. The length of the cross
tee closest to the wall is adjusted. The grid system is adjusted
to the accurate height. Every 5th main beam and all cross tees
against the wall, are fixed to the wall with wall brackets.
At the longitudinal assembly of the main beams the couplings
should be pushed together until they click. Adjust the hangers
to ensure all main beams are in level with the wall angle. The
main beam should not be rested on the wall angle, but placed
approx. 15 mm over the wall angle.
300 mm
A B
DC
15 mm
Distance between profiles

Mounting of Gyptone edge D1 ceiling tiles
GYPTONE
GYPTONE
When mounting the Gyptone tiles, use cotton gloves. The tiles
are lifted perpendicular into the grid system. The J-profile is
slid over the edge of the main beam, and the tile is placed
in position with the Z-profile resting on the opposite main
beam. Slide/push the tiles in place in the direction of the main
beam. Be careful not to damage the tiles. Mounting of tiles
should always be started from the center of the room. All
installations should be completed before mounting the tiles.
Adjusting the frieze tiles against the wall: The front of the tile
is marked. The Z and J profile on the back is shortened with
a hacksaw or similar. Turn the tile and cut the tile cardboard.
Frieze tiles should not be cut with an undersize of more than
max 5 mm.
E
Gyptone edge D1 installed in concealed T-24 grid system.
H
F
When mounting the friezes against the wall, place 2 wall
springs per tile. The short side of the spring is squeezed
between the wall angle and the wall.
G
J-profile
Z-profile

Mounting of T-grid system and Gyptone edge D1 tiles
Dimensions T24 grid system
Estimated consumption installation of suspended grid system
Grid system
Product Term T24 Length mm cc mm Usage/m²
1 Main beam 4810181 3000 600 1.67 m
2 Cross tee D1 4849111 600 1200 0.83 m
3 Wall angle 4133301 3000 24x24 Measurement
4 Adjustable hanger - - 1200 1.39 pcs
5 Wall spring 4133301 3000 24x24 3.3 pcs per m wall angle
2415
38
Max.
100 mm
Max.
1200 mm
Min.
200 mm
600 mm
Min.
200 mm
1
2
4
5
3
Main beam
L: T-24 3600 mm
Wall angle
L: 3000 mm
Cross tee D1
L: 600 mm
cc 1200 mm
1
2
3
Adjustable hangers
for lengths between
90-1500 mm
5
Wall spring4
19
24
24
1512
25
5
15
38
19
24
24
1512
25
5
15
38
19
24
24
1512
25
5
2415
38 38
19
24
24
1512
25
5
15
38
19
24
24
1512
25
5
NB! Gyptone cross tee must always be used.
Cross tees should always be placed next to a
hanger.

The height is measured without any Gyptone tiles and with-
out attachment to the slap above the ceiling. The distance is
from the top of the hanger to the bottom of the grid system.
T-grid system with adjustable hangers
Min.100mm
To ensure easy mounting of the tiles in the grid system,
the distance between the lower surface of the grid and the
above element of building should be min 100 mm.
Gyptone edge D1, suspension of
grid system
Gyptone edge D1, frieze solutions
Mounting of T-grid system and Gyptone edge D1 ceiling tiles
T24 Adjustable 9-12 Min. height 100 mm Max. height 130 mm
Max. 300 mm. Max. 300 mm.
25
5
5
7 8
10
11
4
2
9
11
7 7
6 4
2
1
2
3
4
5
6
7
8
9
10
11
24 mm main beam 4810181,
c/c distance 600 mm.
24 mm cross tee D14149111,
Adjustable hanger,
Gyptone ceiling tile edge D1.
Wall angle GK-C, fixed to wall
every 300 mm.
Main beam GK 1.
Adjusted main beam GK-1,
Connecting bracket GK 21.
Hanger GK 26-25, c/c distance
900 mm.
Gyproc Kortplank, GKP 13
(recessed edge from factory).
Gyproc screw QS 25.
Learn more on
www.gyptone.com
1
2
3
4
5
6
7
24 mm main beam 4810181,
c/c distance 600 mm. (every 5th
main beam is fixed to the wall).
24 mm cross tee D1 4149111,
Adjustable hanger
Gyptone tiles edge D1.
Corner profile H 50/50, fixed to
wall every 400 mm, use screws
with pan-head.
15,5 mm fitted plasterboard
GFKP 15 (Recessed edge from
factory) (Jointing supporters
with steel base plate and
filters/screw).
Gyproc screw QS 25.
Learn more on
www.gyptone.com
1
1
6
3
3

Min. 24 mm
Installation of light fitting in Gyptone D1 ceiling – detail
Installation of light fitting in Gyptone D1 ceiling
Installation of light fitting in Gyptone D1 ceiling.
Installation of light fitting in Gyptone D1 ceiling
Installation of light fitting in Gyptone D1 ceiling – detail.
Min. 24 mm
Min. 24 mm
Min. 24 mm

Gyptone Edge D1 – Installation manual 7
Gyptone edge D1 – Good advice
Corners with wall angle
Butt joint Mitre joint Overlap joint
How to handle the tile boxes on site
Placing the first hanger and cross tee Max. 1 kg load per tile
Placing the wall springs Use the appropriate cross tees
Gyptone D1
Gyptone D1
Gyptone D1
Gyptone D1
Max. 2 mm air
Max. 100 mm.
Main beam is
raised 15 mm
above the wall
angle
GyptoneD1
GyptoneD1

Gyptone Edge D1 – Installation manual 8
Gyproc A/S
Hareskovvej 12
DK-4400 Kalundborg
Ph: +45 59 57 03 30
e-mail: info@gyproc.com
www.gyptone.com
ISO and OHSAS
Gyproc A/S has a quality management system, which is
certified by BVQI Denmark A/A according to the demands
in ISO 9001, 14001 and OHSAS 18001
Humidity in the room should not
exceed 70% during installation or
usage
Fix wall angles to the wall with a
max of 300 mm distance between
the screws
Hangers should be at every
1200 mm. First hanger should be
max. 100 mm from the wall
Main beams are placed with a cc
distance of 600 mm and cross tees
with a cc distance of 1200 mm.
Cross tees should always be placed
next to a hanger
Main beams and cross tees against
the wall should be held 15 mm
above the wall angle
Always use the specified D1 cross
tees for mounting Gyptone D1
ceilings
All cross tees against the wall should
be fixed to the wall
Use 2 wall springs per tile facing the
wall
Gyptone edge D1 tiles have a max
load capacity of 1kg
Checklist for mounting of T-grid system and Gyptone edge D1 ceiling tiles

Gyptone edge d1 installation manual

Empfohlen

Empfohlen

Weitere ähnliche Inhalte

Was ist angesagt?

Was ist angesagt? (9)

Andere mochten auch

Andere mochten auch (12)

Ähnlich wie Gyptone edge d1 installation manual

Ähnlich wie Gyptone edge d1 installation manual (20)

Kürzlich hochgeladen

Kürzlich hochgeladen (20)

Gyptone edge d1 installation manual