1. LECTURE-1
 INTRODUCTION TO ACTUATORS
UNIT 2

3. • An actuator is a component of a machine that is
responsible for moving and controlling a
mechanism or system
(OR)
• An actuator is a device that uses a form of power to
convert a control signal into mechanical motion.
09-09-2021
3

4. 09-09-2021
4

5. • An actuator requires a control signal and a source of
energy.
• The control signal is relatively low energy and may be
electric voltage or current, pneumatic or hydraulic
pressure, or even human power.
• Its main energy source may be an electric current,
hydraulic fluid pressure, or pneumatic pressure. When it
receives a control signal, an actuator responds by
converting the source's energy into mechanical motion.
• An actuator is the mechanism by which a control system
acts upon an environment. The control system can be
simple (a fixed mechanical or electronic system), software-
based (e.g. a printer driver, robot control system), a human,
or any other input.[
09-09-2021
5

6. What is an actuator?
> Actuators are devices used to produce action or motion.
>Input(mainly electrical signal , air, fluids)
>Electrical signal can be low power or high power.
> Actuators output can be position or rate i. e. linear
displacement or velocity.
> Actuation can be from few microns to few meters

8. Types of actuators:
>Hydraulic actuator.
>Pneumatic actuator.
>Mechanical actuator.
>Electrical actuator
>Linear actuator: solenoid, Hydraulic/Pneumatic.
>Rotary actuator: motor, Hydraulic/Pneumatic.

9. >A solenoid is a coil wound into a tightly packed helix.
>In physics, the term solenoid refers to a long, thin loop of wire,
and wrapped around a metallic core.
>which produces a magnetic field when an electric current is
passed through it.

10. Application
^Pneumatic valve.
>Car door openers.
Solenoids controlled valves
Single pressure line

11. Hydraulic actuator:
>Hydraulic systems are used to control & transmit power.
>A pump driven by prime mover (electric motor) creates flow of fluid
Types of hydraulic actuator
Linear actuator (hydraulic cylinder)-
>Provides motion in straight line.
>Linear displacement depends on stroke length.
>Usually referred to as cylinders, rams (single acting cylinders) or jacks.
Rotary actuators (Hydraulic motors)-
>Produces continuous rotational motion.
>Pump shaft is rotated to generate flow.
>A motor shaft is caused to rotate by fluid being forced into the driving
chambers.

12. Semi rotary actuators-
>Produces non-continuous rotational motion. >Limited to
less than one revolution (<360°).
>Used to produce oscillatory motions in mechanisms.
Applications
^Hydraulic jack.
^Hydraulic brake.
^Hydraulic ram.
>Used as sensor.
>Close loop velocity controlling.
>Highly precise positioning for heavy loads.

13. Pneumatic actuator
>It convert energy formed by compressed air at high pressure into
ether linear or rotary motion.
>Quickly respond in operation.
CONSTRUCTIONAL FEATURES OF CYLINDER

14. Hydraulic & pneumatic actuators: cylinders
Single acting:
work can be done only in one
direction
Plunger
Piston
Telescopic
Double acting piston
Work is done in both directions
Piston rod on both sides
Tandem
Telescopic
■
10

15. Double acting cylinder with & without cushioning
>Non cushioned cylinders are suitable for full stroke working at slow speed.
>Higher speeds with external cushions.
i
s cushioning & c a l
p ii(On iaalS

16. Rotary hydraulic actuators
Vane rotary actuator:
> Limited angle in both directions.
> Maximum angle always smaller than
360°
> The same torque in both directions.
Parallel
piston
rotary
actuator
Limited angle
rotary actuator
Piston rotary actuator:
Limited angle rotary
actuator
> With rack and gear coupling.
> Here maximum angle may be larger than
360°
12

17. Mechanical actuator
>Mechanical linear actuators typically
operate by conversion of rotary motion
into linear motion.
Types of mechanics
>Screw
>Wheel and axle
>Cam

18. Electrical actuator
>ElectricaNy actuated system are very widely used in control system
Working Principle of motor
Every motor works on the principle that when a current-carrying
conductor is placed in a magnetic field, it experiences a mechanical force.
>There are three types of motor used in control system
>D.C. motor
>A.C. motor
>Stepper motor

19. >A.C. motor
>Stepper motor
A stepper motor is an electromechanical device which converts electrical pulses
into discrete mechanical movements.
>Permanent magnet type
>Variable reluctance type
>Hybrid type

20. Piezoelectric actuators
> Pierre and Jacques Curie discovered the piezoelectric effect in 1880.
>The application of an electric field to a piezoelectric crystal leads to a
physical deformation of the crystal.
> Piezoelectric materials are: Quartz, Ceramics, PZT(lead zirconate
titanade).
^Advantages
>short response time.
>An ability to create high forces.
>A high efficiency and a high mechanical durability.
> Disadvantage
>Have small strains. (0.1-.2%)
>High supply voltage needed.(60-1000V)
> Large hysteresis.(actuator doesn’t go back to exactly where it started).

21. Configuration
> A piezo ceramic crystal is coated with silver on both sides.
> Glued to a brass, nickel alloy, or stainless steel disk.
> Brass:
^Commercial & industrial use.(not subjected to environment
) >Nickel alloy:
>Use where it subjected to environment.
> Stainless steel:
>Uses where it subjected to solvent, corrosive chemical,
Underwater .
>Medical fields.

22. Types of piezoelectric actuators
> Piezoelectric Stack Actuators
^Produce linear motion.
>Linear motor
>Piezoelectric bender actuator

23. Other type of actuator
Heaters - used with temperature sensors And temperature controller
to control the temperature in automated moulding Equipment and in soldering
operation.
Lights - Lights are used on almost all machines to indicate the machine state
and provide feedback to the operator.
>LED > LCD's
>Gas plasma display >CRT
Sirens/Horns - Sirens or horns can be useful for unattended or dangerous
machines to make conditions well known.

24. LECTURE-2
 STEPPER MOTOR
 SERVO MOTOR

25. STEPPER MOTOR

26. INTRODUCTION
A stepper motor or step motor or stepping
motor is a brushless DC electric motor that
divides a full rotation into a number of equal
steps.
The motor's position can then be commanded
to move and hold at one of these steps
without any position sensor for feedback (an
open-loop controller), as long as the motor is
carefully sized to the application in respect to
torque and speed.

27. What is a stepper motor?
The stepper motor is an electromagnetic
device that converts digital pulses into
mechanical shaft rotation.
A servomotor is a rotary actuator or linear
actuator that allows for precise control of
angular or linear position, velocity and
acceleration

28. What is a stepper motor?

29. What is a stepper motor?
Stepper motors are DC motors that move in
discrete steps.
They have multiple coils that are organized in
groups called "phases".
By energizing each phase in sequence, the
motor will rotate, one step at a time.
With a computer controlled stepping you can
achieve very precise positioning and/or speed
control.

30. Why stepper motor is used?
Stepper motors are versatile, brushless,
synchronous motors that are widely used in a
variety of applications.
Because stepper motors can move in
accurate, discrete angular increments (steps)
in reaction to electrical input pulses, they are
ideal for applications that require controlled,
precise movements.

31. How Stepper Motors Work?
 Stepper motors consist of a permanent magnetic
rotating shaft, called the rotor, and electromagnets on
the stationary portion that surrounds the motor, called
the stator.
 Figure illustrates one complete rotation of a stepper
motor.
 At position 1, we can see that the rotor is beginning at
the upper electromagnet, which is currently active (has
voltage applied to it).
 To move the rotor clockwise (CW), the upper
electromagnet is deactivated and the right
electromagnet is activated, causing the rotor to move
90 degrees CW, aligning itself with the active magnet.
 This process is repeated in the same manner at the
south and west electromagnets until we once again
reach the starting position.

34. Types of Stepper Motor
There are three main types of stepper motors:
1. Permanent magnet stepper
2. Variable reluctance stepper
3. Hybrid synchronous stepper

35. Advantages of step motors
 Low cost,
High reliability
High torque at low speeds
A simple, rugged construction that operates in
almost any environment.
Disadvantages of step motors
Low efficiency
No feedback
Limited high speed torque

36. Applications:
Industrial Machines – Stepper motors are
used in automotive gauges and machine
tooling automated production equipment's.
Security – new surveillance products for the
security industry.
Medical – Stepper motors are used inside
medical scanners, samplers, and also found
inside digital dental photography, fluid pumps,
respirators and blood analysis machinery.
Consumer Electronics – Stepper motors in
cameras for automatic digital camera focus
and zoom functions.

37. SERVO MOTOR

38. INTRODUCTION
A servomotor is a rotary actuator or linear
actuator that allows for precise control of
angular or linear position, velocity and
acceleration.
It consists of a suitable motor coupled to a
sensor for position feedback.
It also requires a relatively sophisticated
controller, often a dedicated module designed
specifically for use with servomotors.

39. INTRODUCTION
Servomotors are not a specific class of motor
although the term servomotor is often used to
refer to a motor suitable for use in a closed-
loop control system.
Servomotors are used in applications such as
Robotics
CNC machinery
Automated manufacturing

40. Why we use Servo Motor?
The main reason behind using a servo is that it
provides angular precision, i.e. it will only
rotate as much we want and then stop and
wait for next signal to take further action.
The servo motor is unlike a standard electric
motor which starts turning as when we apply
power to it, and the rotation continues until
we switch off the power.
We cannot control the rotational progress of
electrical motor, but we can only control the
speed of rotation and can turn it ON and OFF.

41. What is Servo Motor?
• Servo motor is a special type of motor which
is automatically operated up to a certain limit
for a given command with the help of error-
sensing feedback to correct the performance.

42. Servo Mechanism
It consists of three parts:
1.Controlled device
2.Output sensor
3.Feedback system

43. WORKING PRINCIPLE OF SERVO MOTORS
 A servo consists of a Motor (DC or AC), a
potentiometer, gear assembly and a controlling circuit.
 First of all we use gear assembly to reduce RPM and to
increase torque of motor.
 Say at initial position of servo motor shaft, the position
of the potentiometer knob is such that there is no
electrical signal generated at the output port of the
potentiometer.
 Now an electrical signal is given to another input
terminal of the error detector amplifier.
 Now difference between these two signals, one comes
from potentiometer and another comes from other
source, will be processed in feedback mechanism and
output will be provided in term of error signal.

44. WORKING PRINCIPLE OF SERVO MOTORS
 This error signal acts as the input for motor and motor
starts rotating.
 Now motor shaft is connected with potentiometer and
as motor rotates so the potentiometer and it will
generate a signal.
 So as the potentiometer’s angular position changes, its
output feedback signal changes.
 After sometime the position of potentiometer reaches
at a position that the output of potentiometer is same
as external signal provided.
 At this condition, there will be no output signal from
the amplifier to the motor input as there is no
difference between external applied signal and the
signal generated at potentiometer, and in this situation
motor stops rotating.

45. TYPES OF SERVO MOTOR
• There are two types of servo motor,
1. AC Servo motor
2. DC Servo motor

46. Advantages:
If a heavy load is placed on the motor, the driver
will increase the current to the motor coil as it
attempts to rotate the motor. Basically, there is
no out-of-step condition.
High-speed operation is possible.
Disadvantages:
Since the servomotor tries to rotate according to
the command pulses, but lags behind, it is not
suitable for precision control of rotation.
Higher cost.
When stopped, the motor’s rotor continues to
move back and forth one pulse, so that it is not
suitable if you need to prevent vibration

47. Applications of Servo Motors
Servomotors are used in applications requiring rapid
variations in speed without the motor getting overheated.
 In Industries they are used in machine tools, packaging, factory
automation, material handling, printing converting, assembly lines,
and many other demanding applications robotics, CNC machinery or
automated manufacturing.
 They are also used in radio controlled airplanes to control the
positioning and movement of elevators.
 They are used in robots because of their smooth switching on and off
and accurate positioning.
 They are also used by aerospace industry to maintain hydraulic fluid in
their hydraulic systems.
 They are used in many radio controlled toys.
 They are used in electronic devices such as DVDs or Blue ray Disc
players to extend or replay the disc trays.
 They are also being used in automobiles to maintain the speed of
vehicles.

48. LECTURE-3
 STEPPER MOTOR
 TYPES OF STEPPER MOTOR
 WORKING PRINCIPLE

49. What is a stepper motor?
The stepper motor is an electromagnetic
device that converts digital pulses into
mechanical shaft rotation.

50. What is a stepper motor?

51. CONSTRUCTION OF STEPPER MOTROR
 Like all electric motors it has stator and rotor. The rotor is the
movable part which has no windings, brushes and a
commutator.
 Usually the rotors are either variable reluctance or permanent
magnet kind.
 The stator is often constructed with multi pole and
multiphase windings, usually of three or four phase windings
wound for a required number of poles decided by desired
angular displacement per input pulse.
 Unlike other motors it operates on a programmed discrete
control pulses that are applied to the stator windings via an
electronic drive.
 The rotation occurs due to the magnetic interaction between
poles of sequentially energized stator winding and poles of
the rotor.

52. CONSTRUCTION OF STEPPER MOTROR

54. Types of Stepper Motor
There are three main types of stepper motors:
1. Permanent magnet stepper
2. Variable reluctance stepper
3. Hybrid synchronous stepper

55. Types of Stepper Motor
1. Permanent magnet motors use a permanent
magnet (PM) in the rotor and operate on the
attraction or repulsion between the rotor PM
and the stator electromagnets.
2. Variable reluctance (VR) motors have a plain
iron rotor and operate based on the principle
that minimum reluctance occurs with minimum
gap, hence the rotor points are attracted toward
the stator magnet poles.
3. Hybrid synchronous are a combination of the
permanent magnet and variable reluctance
types, to maximize power in a small size

56. Types of Stepper Motor

57. 1. PERMANENT MAGNET STEPPER MOTOR
• Often referred to as a “tin can” or “canstock” motor the
permanent magnet step motor is a low cost and low-
resolution type motor with typical step angles of 7.5° to 15°
(48–24steps/revolution).
• PM motors as the name imply have permanent magnets
added to the motor structure. The rotor no longer has teeth
as with the VR motor. Instead, the rotor is magnetized with
alternating north and south poles situated in a straight line
parallel to the rotor shaft.
• These magnetized rotor poles provide an increased magnetic
flux intensity and because of this the PM motor exhibits
improved torque characteristics when compared with the VR
type.

58. 1. PERMANENT MAGNET STEPPER MOTOR

59. 1. PERMANENT MAGNET STEPPER MOTOR

60. 2. VARIABLE RELUCTANCE STEPPER MOTOR
• This type of stepper motor has been around for a
long time. It is probably the easiest to understand
from a structural point of view.
• The figure shows a cross section of a typical Variable
Reluctance stepper motor. This type of motor
consists of a soft iron multi-toothed rotor and a
wound stator.
• When the stator windings are energized with DC
current the poles become magnetized. Rotation
occurs when the rotor teeth are attracted to the
energized stator poles.

61. 2. VARIABLE RELUCTANCE STEPPER MOTOR

62. 2. VARIABLE RELUCTANCE STEPPER MOTOR

63. 3. HYBRID STEPPER MOTOR
• The hybrid stepper motor is more expensive than the PM
stepper motor but provides better performance with respect
to step resolution, torque, and speed. Typical step angles for
the HB stepper motor ranges from 3.6° to 0.9° (100 – 400
steps per revolution).
• The hybrid stepper motor combines the best features of both
the PM and VR type stepper motors. The rotor is multi-
toothed like the VR motor and contains an axially magnetized
concentric magnet around its shaft.
• The teeth on the rotor provide an even better path which
helps guide the magnetic flux to preferred locations in the air
gap. This further increases the detent, holding and dynamic
torque characteristics of the motor when compared with both
the VR and PM types.

64. 3. HYBRID STEPPER MOTOR

65. Advantages of stepper motors
 Low cost,
High reliability
High torque at low speeds
A simple, rugged construction that operates in
almost any environment.
Disadvantages of stepper motors
Low efficiency
No feedback
Limited high speed torque

66. Applications:
Industrial Machines – Stepper motors are
used in automotive gauges and machine
tooling automated production equipment's.
Security – new surveillance products for the
security industry.
Medical – Stepper motors are used inside
medical scanners, samplers, and also found
inside digital dental photography, fluid pumps,
respirators and blood analysis machinery.
Consumer Electronics – Stepper motors in
cameras for automatic digital camera focus
and zoom functions.

67. LECTURE-4
 SERVO MOTOR
 TYPES OF SERVO MOTOR
 WORKING PRINCIPLE

68. What is Servo Motor?
• Servo motor is a special type of motor which
is automatically operated up to a certain limit
for a given command with the help of error-
sensing feedback to correct the performance.

69. What is a stepper motor?
The stepper motor is an electromagnetic
device that converts digital pulses into
mechanical shaft rotation.
A servomotor is a rotary actuator or linear
actuator that allows for precise control of
angular or linear position, velocity and
acceleration

70. TYPES OF SERVO MOTOR
• There are two types of servo motor,
1. AC Servo motor
2. DC Servo motor
• Brushed permanent magnet DC servo motors
are used for simple applications owing to their
cost, efficiency and simplicity. These are best
suited for smaller applications.
• With the advancement of microprocessor and
power transistor, AC servo motors are used
more often due to their high accuracy control.

71. DC SERVO MOTOR
As we know that any electrical motor can be
utilized as servo motor if it is controlled by
servomechanism.
Likewise, if we control a DC motor by means of
servomechanism, it would be referred as DC
servo motor.
There are different types of DC motor, such shunt
wound DC motor, series DC motor, Separately
excited DC motor, permanent magnet DC motor,
Brushless DC motor etc.
Among all mainly separately excited DC motor,
permanent magnet DC motor and brush less DC
motor are used as servo.

72. DC SERVO MOTOR

73. CONSTRUCTION OF DC SERVO MOTOR

74. CONSTRUCTION OF DC SERVO MOTOR
• A DC servo motor consists of a small DC motor,
feedback potentiometer, gearbox, motor drive
electronic circuit and electronic feedback control
loop. It is more or less similar to the normal DC
motor.
• The stator of the motor consists of a cylindrical
frame and the magnet is attached to the inside of
the frame.
• The rotor consists of brush and shaft. A
commutator and a rotor metal supporting frame
are attached to the outside of the shaft and the
armature winding is coiled in the rotor metal
supporting frame.

75. CONSTRUCTION OF DC SERVO MOTOR
• A brush is built with an armature coil that supplies the
current to the commutator. At the back of the shaft, a
detector is built into the rotor in order to detect the
rotation speed.
• With this construction, it is simple to design a
controller using simple circuitry because the torque is
proportional to the amount of current flow through the
armature.
• And also the instantaneous polarity of the control
voltage decides the direction of torque developed by
the motor. Types of DC servo motors include series
motors, shunt control motor, split series motor, and
permanent magnet shunt motor.

76. WORKING OF DC SERVO MOTOR
• The motor which is used as a DC servo motor generally
have a separate DC source in the field of winding &
armature winding.
• The control can be archived either by controlling the
armature current or field current.
• Field control includes some particular advantages over
armature control.
• In the same way armature control includes some
advantages over field control.
• Based on the applications the control should be
applied to the DC servo motor.
• DC servo motor provides very accurate and also fast
respond to start or stop command signals due to the
low armature inductive reactance.
• DC servo motors are used in similar equipment's and
computerized numerically controlled machines.

77. AC SERVO MOTOR
AC servo motors are basically two-phase squirrel
cage induction motors and are used for low
power applications.
Nowadays, three phase squirrel cage induction
motors have been modified such that they can be
used in high power servo systems.
The main difference between a standard split-
phase induction motor and AC motor is that the
squirrel cage rotor of a servo motor has made
with thinner conducting bars, so that the motor
resistance is higher.

78. CONSTRUCTION OF DC SERVO MOTOR
• There are two distinct types of AC motors based
on construction: synchronous and induction.
• Induction motors are constructed of shortened
wire loops on a rotating armature. Voltage is
'induced' in the rotor through electromagnetic
induction. They are rugged, versatile, and can
provide considerable power as well as variable
speed control.
• Synchronous motors are constructed of a wound
rotor where coils of wire are placed in the rotor
slots. These motors are designed to operate at a
specific speed, in step with the rotating magnetic
field.

79. CONSTRUCTION OF DC SERVO MOTOR
INDUCTION MOTORS SYNCHRONOUS MOTORS

80. WORKING OF DC SERVO MOTOR
AC servo motor is an AC motor that includes
encoder is used with controllers for giving
closed loop control and feedback.
This motor can be placed to high accuracy and
also controlled precisely as compulsory for the
applications.
Frequently these motors have higher designs
of tolerance or better bearings and some
simple designs also use higher voltages in
order to accomplish greater torque.

81. DC Servo Motor AC Servo Motor
It delivers high power output Delivers low output of about 0.5 W to 100 W
It has more stability problems It has less stable problems
It requires frequent maintenance due to the
presence of commutator
It requires less maintenance due to the absence
of commutator
It provides high efficiency
The efficiency of AC servo motor is less and is
about 5 to 20%
The life of DC servo motor depends on the life
on brush life
The life of AC servo motor depends on bearing
life
It includes permanent magnet in its construction
The synchronous type AC servo motor uses
permanent magnet while induction type doesn’t
require it.
These motors are used for high power
applications
These motors are used for low power
applications
Difference between the DC and AC Servo Motors