SlideShare ist ein Scribd-Unternehmen logo
1 von 36
Downloaden Sie, um offline zu lesen
ATA Number ATA Chapter name
ATA 71 POWER PLANT
ATA 72 ENGINE CONSTRUCTION
ATA 73 FUEL AND CONTROL
ATA 74 IGNITION
ATA 75 AIR SYSTEM
ATA 76 CONTROLS
ATA 77 INDICATING
ATA 78 THRUST REVERSER
ATA 79 OIL SYSTEM
ATA 80 STARTING
ENGINE ATA CHAPTERS
Engine Specification
EPR
Engine Thrust
EGT Limit [margin]
SFC
Engine Weight
Power Plant Weight
Fan diameter
T Flat (ISA + 15 )
By-Pass ratio [1:5]
CPR
Number of rotors , speeds
[N1, N2,…]
Speed limits [N1,N2,N3]
Thrust setting parameter [
EPR , N1 ]
Mechanical standards/
arrangements
Gearbox location [ core/fan
mounted]
Direction of rotation
Engine Performance
Engine Performance
Engine Performance
Engine Performance
Engine Performance
Engine Performance
Aircraft Engine
The cowls enclose the periphery of the engine so as to form the engine nacelle, underneath the aircraft wings.
The nacelle is the aerodynamic structure around the basic engine and has several purposes:
- To smooth the airflow around and into the engine, in order to decrease drag and give better engine
performance.
- To prevent damage to the external surface of the engine.
- To give extra strength to the engine structure.
- To make connections for air, fluids and electricity.
- To enable access to the engine, or direct access to some engine equipment
Power Plant
Air Inlet Cowl
 The air inlet cowl is at the forward section of the nacelle
Attached on its rear flange to the engine fan case.
Provides a smooth airflow into the engine during all aircraft operational sequences
Prevents ice formation at the front of the power plant.
Has an anti-ice inlet duct, an interphone connector and jack and also houses the Temp. sensor.
 The fan cowl doors
Are manually opened, or closed, and can be held open for engine maintenance purposes.
Each fan cowl door contains three hoist points and two telescopic hold-open rods which support the doors in the open
position.
There are two hold-open positions, 20° and 55°. The 20° position allows access to the lower part of the fan compartment
for maintenance of accessory gearbox components (IDG, hydraulic pump, fuel module, oil system).
The 55° maximum open position allows access to all equipment located in the fan compartment.
One cowl door provides direct access to the starter valve, and the other provides direct access to the oil tank.
Have three hook type latches on the right hand door which mate with adjustable eye bolts on the left hand door.
Index pins provide door positioning at each latch.
The latch handle closing pressure is adjusted with the fan cowl doors closed.
Fan Cowl
 The thrust reverser
Is located between the engine fan cowls and the exhaust nozzle, and comprises two cowls.
Each cowl is hinged at the top to the pylon and latched to the other along the bottom centerline.
In the stow position, the thrust reverser assembly forms the passage for fan secondary airflow to be discharged overboard.
In the deploy position (reverse thrust mode), four hydraulically actuated pivoting doors redirect the secondary airflow forward and provide
a braking effect to reduce the aircraft stopping distance.
Designed for ground operation only.
A hydraulically actuated cowl opening system allows each thrust reverser cowl to be opened independently
 The mechanical structure includes:
- An outer cowl, which forms the fan discharge flow outer contour.
- An inner cowl, which forms the fan flow inner contour, and engine outer envelope.
- Pivoting doors going into the fan stream, blocking and redirecting the secondary airflow outward and forward.
 The C-ducts consist of:
- The outer cowl, or fan outer contour, which is part of the mixed flow nacelle design and which, in the stowed position, encloses the pivoting doors.
- Four hinges which attach the cowl to the pylon. These hinges are an integral part of a machined aluminum beam which runs along the upper portion
of the thrust reverser.
- Two hoist points on each outer cowl for removal/ installation maintenance operations.
- Five tension hook latches, which are installed at the bottom of the left hand side outer cowl.
- A “J” flange, at the aft end of the cowl, which mates with the “V” groove of the exhaust nozzle.
- A pressure relief door, located at the bottom, which prevents permanent structural deformation in the event of single bleed duct rupture.
Thrust Reverser Cowl
 The CAN
Collects the cool bypass airflow, the hot core exhaust gases and bleed air flows.
The cool air and hot gases mix and exhaust to atmosphere through a final nozzle.
An interchangeable assembly that has an acoustic outer duct assembly made of graphite/epoxy.
It is held by six aerodynamic metal struts attached to the inner duct assembly.
Is attached directly on to the LP turbine module of the engine.
Common Nozzle
Engine Mounts
Front Mounts
 The engine mounts support the weight of the engine and transmit loads to the aircraft structure through the pylon.
 The front mount
Attached at the top of the intermediate case.
The engine front mount transmits engine thrust, side and vertical loads to the aircraft pylon.
The thrust and side loads are transmitted from the intermediate case through a split spherical bearing – which is mounted on
the intermediate case - to the cylindrical trunnion.
These loads are now transmitted through the main attachment bracket to the aircraft pylon.
The vertical loads are transmitted from the intermediate case through the vertical load links to the vertical load support beam.
They are then transmitted through the front horizontal trunnion to the main attachment bracket to the aircraft pylon.
The main attachment bracket is in two halves to give more than one route for the thrust and side loads.
If there is a failure of a primary component that affects the vertical loading the engine would drop and the fail safe catcher
link would contact the rear trunnion (on the main attachment bracket) and support the vertical loads.
Engine Mounts
Rear Mounts
 The rear mount
Is attached at the top of the exhaust case.
The engine rear mount transmits engine torque loads, vertical loads and side loads to the aircraft pylon.
Aircraft Engine
Engine Construction
Air Intake
Air Intake Design Requirements
 The air intake should be able to.:
Admit the maximum amount of air.
Diffuser :
Deliver the air to compressor with max Mach no. = 0.5 Mach
Produce little aerodynamics drag.
Reduce level of noise by engine.
 The main causes of losses are generally the result of:-
poor sheet metal work, e.g. bad riveting,
Dents, scores and scratches,
Misalignment due to incorrect assembly.
Take care, the intake is a very important part.
 Inlet cone:
Streaming for air.
Anti-ice [ vibration – Hot air ].
Eagle eye : Scare birds.
Engine Construction
Compressor
Function
o Increase the air mass flow
o Improve combustion characteristics
o Increase the efficiency of operating cycle
o Increase the thrust produced by engine
o Improve fuel economy
o Assist in the provision of a small and compact engine.
Principle
o Rotating parts :Increase velocity [add kinetic energy to air].
o Static parts [diffusion]: reduce velocity & convert kinetic energy to pressure energy.
Components
Rotor
Blades
Drum or Disk (Drum = more than one Disk)
Shaft
Stator
Vanes
Casing
Seal Attachment of rotor blades
Solid root
Fir tree root
Dovetail root (Axial root - Radial root)
Radial (Centrifugal) Devices
– Can not handle as high mass flow
– Less efficient than axial device
– Short length
– Robust
– Less Parts
Axial Devices
– High mass flow
– High efficiency
– Stackable (multi-staging)
– More parts
– More complex
TWO PRIMARY TYPES OF COMPRESSORS
Twisted blade design
Root speed (vf) = Π Dr N
As diameter increase, angle of attack increase, so rotation speed increase.
Tip speed (vf) = Π Dt N/60
Root speed (vf) = Π Dt N/60
SO blades are made twisted,
To fast speed recovery so prevent stall
Stall & Surge:
Compressor Surge [ result from stall ] occurs when the inlet flow reduces than certain limit, which leads to flow reversal.
Compressor stall [ start at blades ] occurs when the pressure at down stream of compressor is greater than the compressor discharge pressure which leads
to no discharge from compressor.
Causes:
Surge induced by inlet air flow distortion ( high cross wind, sharp, uncoordinated aircraft maneuvers, intake problem ).
Shear/Side Wind : cause changes in inlet air mass.
FOD [Foreign object damage].
Sudden acceleration and sudden deceleration.
Excessive increase in combustion chamber pressure caused by
rapid opening of the throttle particularly at low engine RPM.
Indications :
Unexpected loss of thrust.
Abnormal engine noises and vibrations.
Un-commanded variations in engine RPM.
Rapid increase in EGT.
In extreme cases the reversal of airflow can result in the ejection of exhaust gasses out of the air intake.
Transient conditions: ( At which surge occur )
1. Rapid acceleration
2. Rapid deceleration
3. Starting [similar to Rapid acceleration ]
Rapid acceleration
Thrust lever ↑
↑ Fuel
↑ HPT blade speed
↑ HPC blade speed
↑ Angle of attack α
↑ air speed
HPC Surge (Front Stages)
Rapid deceleration
Thrust lever ↓
↓ Fuel
↓ HPT blade speed
HPC output air mass same as it
HPT takes only accepted air mass
relative to rotation speed
Back pressure due to rest of air mass
HPC Surge ( Rear Stages)
Function:
o Separate two rolling elements.
o Minimize friction loss.
Bearings reduce friction by providing smooth metal balls or rollers, and a smooth inner and outer metal surface for the balls to roll against.
These balls or rollers "bear" the load, allowing the device to spin smoothly.
Bearing loads
o Radial load (weight load)
o Axial load [thrust load]
Roller bearing
• Large contact area so hold heavy radial loads.
• High load carrying capacity
• Allow thermal expansion
• Mostly used at hot section (shaft end )
Ball bearing (Thrust Bearing)
• Can handle both radial and thrust loads.
• Lower load carrying capacity, higher speed.
• Mostly used at cold section (shaft start) :
o Do not allow thermal expansion
o Location bearing : to prevent shaft and fan from moving forward
OIL SYSTEM
Bearing
Seals
The prime purpose is to prevent leakage at a joint, or it may also help to prevent the ingress of foreign matter into system.
O-ring Seal
• Work under pressure.
• Usage one time only.
Labyrinth Seal
• Most common
• Use shock theory
• High oil consumption
Carbon Seal
• Very sensitive to pressure and temperature.
• Usually used in bearing oil seal.
Brush Seal
Hydraulic Seal
Screw back Seal
Troubleshooting
• Higher than normal oil consumption.
• Higher breather air pressure.
• Dirty inefficient compressor
• Distorted or burnet nozzle guide vanes or turbines.
• Higher fuel consumption.
• Higher than normal turbine gas temperature.
• A decrease in engine performance.
The bearing sump philosophy
• 1st room to prevent oil spillage on other part.
• 2nd room to prevent oil leakage from oil seal due to high oil pressure.
• Also cooling oil, and maintain 1st room pressure within limits.
• Vent (breather air): to eject air enter 1st room through oil seal.
• Restrictor : installed on vent to equalize 1st and 2nd rooms pressure.
• Inspection from drain :
o High pressure oil seal leakage.
o Low pressure air seal leakage.
The bearing sump
Engine Construction
Combustion Chamber
Function
• Complete combustion
• Contain flame
• Convert air and fuel mix to hot gases
• Combustion chamber walls coating
• Complete burning to prevent back fire
Components
• Outer case
• Outer liner
• diffuse
• Inner liner – around inner case
• Inner case – around shaft
Operation
• 18% Primary air
o 10% Enters at the snout (mixed with fuel to start ignition –
direct mix through swirling)
o 8% Enters the primary zone through the walls of the
combustion chamber (contain flame – more mixing )
• 10% Secondary air – turbo flow -
o Provide cooling air on either side of the liner.
o Complete combustion and increase vortex –turbulence to prevent flame
propagation and improve combustion.
• 72% Tertiary air
• Dilution: Provide cooling air on either side of the liner.
• Prevent flame propagation .
Cane-Annular Design
• Lighter weight
• Flame out recovery by interconnection
• Residual fuel drain to prevent choke at starting .
• Residual fuel drain operate by pressure valve depend on C.C pressure.
Cane Design
Thicker structure
x Longer structure
Annular Design
• inner and outer case,
• Inner and outer liner
• One C.C
• Short structure
Annular Design
• SAC : Single Annular Combustion
o One flame outlet – nozzle-
• DAC : Dual Annular Combustion
o Two flame outlet – nozzle
Near C.C liner short life liner
Low emission
Better combustion
Ignition
• More than one igniter on C.C to alternately operate.
• Igniter only work at starting Intel steady state flame condition.
Incomplete combustion result :
due to ineffective swirl, fuel particles stake at turbine blades making hot spots.
At starting hot spots burn and increase blade temperature which lead to remove coating above blades.
Notes
• Combustion chamber shape like diffuser -flame stability - to
lower speed of air coming from compressor to prevent flame off.
• C.C. Pressure reduced due to turbulence inside .
• CDP compressor discharge pressure PB burner pressure .
• Pressure of C.C. change at transient condition.
• Highest thermal stress at takeoff.
• 1:15 optimum combustion efficiency
• Actual combustion efficiency [45:1 130:1 ]
Engine Construction
Turbine
Function
The turbine converts most of the heat and kinetic energy generated by combustion section into mechanical work using expansion.
Types by number of spools
• Single Spool Turbine
• Twin Spool Turbine
• Triple Spool Turbine
Design
Casing shape like diffuser :
to contain flow expansion And to take same power from flow.
because power reduced due to flow expansion.
So larger blade will make same flow mass
push blades to take same power.
Area between vanes shape as nozzle:
To reduce flow pressure & temperature
and increase velocity.
In one word : Flow Expansion
Components
NGV’s
• Turbine nozzle guide vane
• Function : to increase the velocity of the gas stream
and direct it at the optimum angle of attack on to the turbine blades.
• Flow Temp, Pressure ↓ Velocity ↑
Blades
• Blade (fir tree root)
To allow thermal expansion and rigidity
• Blade (twisted)
To stabilize flow velocity with diameter variation
• No drum – no welding – in turbine :
Disks fixed using bolts.
• Blade tip:
o Easy to broke by F.O.D to protect case.
o Anti-corrosion surface.
• Material [ Mono crystal – Ceramic ]
Shroud
Protect case via clearance [ 8% 3.5% losses ]
Sealing to prevent flow leakage
Cold to perfectly close at blades
Segment : group of vanes
Impulse type
A stator vane and rotor blade arrangement whereby the vanes form convergent ducts and
the blades form straight ducts. The rotor is then turned by impulse as gases impinge
on the blades.
o [ Rotor → Power ]
o Usually used in LPT
Reaction type
Produces rotation by the aerodynamic action of the air as it accelerates between the
blades.
The reaction to the force generated by the accelerated air causes the turbine to rotate.
o [ Rotor → Nozzle → Expansionpower ]
Impulse/Reaction type
A stator vane and rotor blade arrangement whereby :
the base area is an impulse - low flow velocity -
the tip is a reaction design - high flow velocity – to reduce it
Turbine Types
Engine Construction
Exhaust system
Functions
•Accelerate hot gases to increase thrust. [Diffuser shape]
• Clear exhaust gases to prevent back pressure.
Components
1. Exhaust Nozzle
[ Flow acceleration & expansion ]
2. Propelling nozzle
[ Secondary Flow streaming guiding ]
3. Exhaust cone (plug)
- Stop turbulence
- primary Flow streaming guiding
- Protect disks and bearing
Duct Types
Mixed flow design
Reduce Noise
Duct Types
Non mixed flow design
Problems
•Drag on inner surface
•Noisy
Aircraft Engine
Fuel & Control
EEC
DADC
TMC
COCKPIT
DISPLAY
ENGINE
TLA
To
Po
POWER
SOURCE
To
Po
PLA
METERED FUEL
FLOW SIGNAL
TORQUE
MOTOR
DRIVE
FAIL/FAIXED
SLONIOD
METERING
VALVE
FEEDBACK
ENGINE
SPEED
FCU
Computing Section Metering Section
CDP
LIMITER
Speed
Controller
3D CAM
Main
Filter
Regulating
Valve
FMU
FFT
Shut off
valve
CDP
CDP
N2
SPEED
CIT
To , Po
Trim
Adj
Cut off switch
Servo
Filter
Servo
Supply
Operate
(sensor/valves)
Cooling
Lubricant
Low
Pressure
Pump
Fuel Heater
&
Filter
High
Pressure
Pump
Return to
HPP
Fault
Monitor
Fuel & Control
Low Pressure Pump
Fuel Heater
High Pressure Pump
Fuel Control Unit
Fuel Flow Transmitter
Fuel Cooled Cooler
Flow Divider
Fuel Nozzle
Ensures an adequate 'head of pressure' at the inlet to the pump
preventing cavitations of the pump during normal operation.
Ensures that any ice particles are removed from the fuel before the fuel reaches the Fuel Control Unit (FCU).
Hot air for heating the fuel is drawn from the engine compressor.
Connected with the LPP by a shaft have a weak point to shear in case of pump failure to protect the G.B
Meters and supplies the correct amount of fuel to the engine burners depending upon throttle
position and the various environmental conditions
Indicates to the flight deck crew the amount of fuel flowing from the fuel control unit to the engine.
Although part of the fuel system has a primary function to cool the oil from the engine lubricating
system. The cold fuel cools the oil and at the same time the oil heats the fuel.
Directs the fuel flow to either the primary or the secondary fuel nozzles.
The function of the nozzle is to inject fuel into the combustor chamber in a highly atomized form,
which aids the combustion of the fuel
Externally mounted, Internally mounted
Variable Disp. Piston type
Constant Disp. With relief valve
SIMPLEX : only a single manifold supply is
required
Duplex : is usually associated with a dual flow
manifold, which receives both secondary and
primary fuel flow.
Thrust Management
Computer
Fault monitor
Fuel Control Unit
Electronic Engine
Control Computer
Metered Fuel
Although not part of the fuel metering system, it allows the flight crew to select a thrust setting in
flight, i.e., climb, cruise, take-off, etc.
It also displays, on the flight deck, the maximum engine speed for a given thrust setting
Stores fault information from the electronic engine control unit.
Meters and computes the fuel flow to the engine, a hydro mechanical computer.
Controls the engine speed to suit the pressure and temperature conditions of the day.
The fuel from the FCU to the aircraft is fuel which has been metered to enable the engine to
produce the correct amount of thrust for a given condition and throttle lever position.
Fuel & Control
Electronic Engine
Control
Digital Air Data
Computer
The primary purpose of an electronic engine control system is to reduce the pilot's work load by
computing, displaying and maintaining the selected engine settings as a function of external
sensors and selected flight modes.
The primary source of pressure and temperature sensing. This information is passed to the thrust
management and the electronic the primary source of pressure and temperature sensing. This
information is passed to the thrust management and the electronic engine control computers.
Aircraft Engine
IGNITION
The ignition sequence is cancelled when the
starter cycle is
cancelled.
to provide a very high voltage to jump a wide
igniter plug spark gap, and also, a high
intensity spark. The
high energy capacitor type ignition system has
been fitted to
gas turbine engines since it provides both a
high voltage and
an exceptionally hot spark over the area of the
spark gap.
Thus the chances of igniting the fuel/air
mixture are assured
at reasonably high altitudes.
Aircraft Engine
Function
• Stability Bleed : stall and surge prevention devices
o VSV Variable Stator Vane (MODULATED)
o Usage : to stop stall –angle of attack change or m - occur in first stages in HPC when rapid acceleration condition applied.
o Operation : actuator controlled via EEC – after sensing temp and pressure.
o Always Synchronized with VBV .
o Failsafe : fully open
o Worth case : take off fully opened Surge
o Hydraulically or pneumatically operated – using fuel
• Easy to get rid of it, if any problem happened because there is a lot of fuel.
• To prevent stress on oil maintain oil viscosity
• To let EEC fully control Valves
• To reduce interfaces between airplane and engine
o Electrically controlled
o VBV Variable Bleed Valve ( )
o Usage : to stop surge if air accumulation occur between LPC & HPC when rapid deceleration condition applied via ventilation.
o Operation : master valve controlled via EEC, slave valves follow .
o Hydraulically or pneumatically operated – using fuel- .
o Electrically controlled.
o Failsafe : fully open
o Worth case : STUCK OPEN EGT ↑ Powerless Surge
o SBV Surge Bleed Valve ( )
o Usage : to stop surge if air accumulation occur in rear HPC stages via ventilation.
o Operation : fully open or fully closed .
o Pneumatically operated – using fuel- .
o Spring loaded
o Failsafe : fully open
• Service Bleed
o Sealing
Oil sump
o Cooling
• Turbine Blades & Vanes
• HPT Shroud Cooling | Outside/Inside
• LPT Case Cooling
Low loads @ cruise Low temp Turbine blades High tip clearance
Cold air @case Case shrink lower clearance
o ACC Active Clearance Control
o TCC Turbine Case Cooling
Engine Core | Hot air from turbine compressor blade
cooling[heating] compressor blades stretching lower clearance
Rigging
o Only for VSV, VBV.
o To check valve condition at fully open/close selection.
o Recover EGT margin due to valve not fully closed.
Air System
Cooling
o Inlet guide vane: internal cooling.
o HPT: internal cooling.
o LPT: external cooling.
Aircraft Engine
Function
• Lubrication
• Cooling
Oil System
Main components
• Hot Tank (because it’s before cooler )
Function:
o Store oil
o Provide continuous oil supply
Material :
o Aluminum alloy
o Stainless steel
o Composite material
Components:
o Deaerator (separate AIR from oil)
o Breather (separate OIL from air)
o Pump
o Oil filter
o Oil cooler
o Chip detector
• Types : master Chip detector + slaves Chip detector
• On scavenge line after user and before pump
• Heat management ( to control oil temp. )
o ACOC AOHE Air Cold Oil Cooler
o FCOC FOHE Fuel Cold Oil Cooler
• Supply line
• Scavenge line and pumps ( recalculate oil)
• Pressure relive valve
• Chip detector
• Breather -vent- (separate OIL from air)
• Deaerator (separate AIR from oil)
• ΔP Switch : Pressure relive valve/over pressure detector
Design wise
Oil can leak into fuel because it’s higher pressure, why?
o oil properties can’t effect fuel
o oil can burn with fuel
Aircraft oil different from cars oil, why?
o In aircraft : running condition easier – no metal to metal friction
o In cars : metal to metal friction – harder running condition
Oil Service
Aircraft engine oil change only if:
o Store engine
o Contamination
o Manufacture order
Aircraft engine oil level check:
After 10 min exactly – not more than 30 min – after engine shutdown?
To allow level of oil settle down in the tank after deaeration

Weitere ähnliche Inhalte

Was ist angesagt?

Aircraft Gas Turbine Engines
Aircraft Gas Turbine EnginesAircraft Gas Turbine Engines
Aircraft Gas Turbine EnginesZafar Jami
 
Hands on experience with aircraft major components on aircraft and to identif...
Hands on experience with aircraft major components on aircraft and to identif...Hands on experience with aircraft major components on aircraft and to identif...
Hands on experience with aircraft major components on aircraft and to identif...Mayank Gupta
 
Aerodynamic design of aeroplane
Aerodynamic design of aeroplaneAerodynamic design of aeroplane
Aerodynamic design of aeroplaneTanveer Hussain
 
Aircraft and engine fuel system and engine lubrication system
Aircraft  and engine fuel system and engine lubrication systemAircraft  and engine fuel system and engine lubrication system
Aircraft and engine fuel system and engine lubrication systemSanjay Singh
 
Aircraft landing gear system
Aircraft landing gear systemAircraft landing gear system
Aircraft landing gear systemKrishikesh Singh
 
Aircraft Systems - Chapter 06
Aircraft Systems - Chapter 06Aircraft Systems - Chapter 06
Aircraft Systems - Chapter 06junio_oliveira
 
Aircraft mechanical cable control system
Aircraft mechanical cable control systemAircraft mechanical cable control system
Aircraft mechanical cable control systemraj_sevak
 
Aircraft Maintenance practices introduction
Aircraft Maintenance practices introduction Aircraft Maintenance practices introduction
Aircraft Maintenance practices introduction Gaurav Garv
 
Aircraft cabin pressurization system
Aircraft  cabin pressurization systemAircraft  cabin pressurization system
Aircraft cabin pressurization systemShrinivas Kale
 
Classification of Aircraft power plants_Aircraft Propulsion
Classification of Aircraft power plants_Aircraft Propulsion Classification of Aircraft power plants_Aircraft Propulsion
Classification of Aircraft power plants_Aircraft Propulsion Suthan Rajendran
 
Basic Aerodynamics Ii Stability Large
Basic Aerodynamics Ii Stability   LargeBasic Aerodynamics Ii Stability   Large
Basic Aerodynamics Ii Stability Largelccmechanics
 
EASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICS
EASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICSEASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICS
EASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICSsoulstalker
 
Aircraft fuel system
Aircraft fuel systemAircraft fuel system
Aircraft fuel systemamineshinobie
 
Aircraft Systems and Instruments
Aircraft Systems and InstrumentsAircraft Systems and Instruments
Aircraft Systems and InstrumentsVarun Karthikeyan
 
Fixed wing aircrafts power point presentation
Fixed wing aircrafts power point presentationFixed wing aircrafts power point presentation
Fixed wing aircrafts power point presentationSamaleswari Prasad Mallik
 
EASA PART-66 MODULE 8.2 : AERODYNAMICS
EASA PART-66 MODULE 8.2 : AERODYNAMICSEASA PART-66 MODULE 8.2 : AERODYNAMICS
EASA PART-66 MODULE 8.2 : AERODYNAMICSsoulstalker
 

Was ist angesagt? (20)

Aircraft Gas Turbine Engines
Aircraft Gas Turbine EnginesAircraft Gas Turbine Engines
Aircraft Gas Turbine Engines
 
Hands on experience with aircraft major components on aircraft and to identif...
Hands on experience with aircraft major components on aircraft and to identif...Hands on experience with aircraft major components on aircraft and to identif...
Hands on experience with aircraft major components on aircraft and to identif...
 
Aerodynamic design of aeroplane
Aerodynamic design of aeroplaneAerodynamic design of aeroplane
Aerodynamic design of aeroplane
 
Aircraft basics
Aircraft basicsAircraft basics
Aircraft basics
 
Aircraft and engine fuel system and engine lubrication system
Aircraft  and engine fuel system and engine lubrication systemAircraft  and engine fuel system and engine lubrication system
Aircraft and engine fuel system and engine lubrication system
 
Aircraft landing gear system
Aircraft landing gear systemAircraft landing gear system
Aircraft landing gear system
 
Aircraft Systems - Chapter 06
Aircraft Systems - Chapter 06Aircraft Systems - Chapter 06
Aircraft Systems - Chapter 06
 
Aircraft mechanical cable control system
Aircraft mechanical cable control systemAircraft mechanical cable control system
Aircraft mechanical cable control system
 
Aircraft Maintenance practices introduction
Aircraft Maintenance practices introduction Aircraft Maintenance practices introduction
Aircraft Maintenance practices introduction
 
Aircraft cabin pressurization system
Aircraft  cabin pressurization systemAircraft  cabin pressurization system
Aircraft cabin pressurization system
 
Basic aircraft control system
Basic aircraft control systemBasic aircraft control system
Basic aircraft control system
 
Classification of Aircraft power plants_Aircraft Propulsion
Classification of Aircraft power plants_Aircraft Propulsion Classification of Aircraft power plants_Aircraft Propulsion
Classification of Aircraft power plants_Aircraft Propulsion
 
Basic Aerodynamics Ii Stability Large
Basic Aerodynamics Ii Stability   LargeBasic Aerodynamics Ii Stability   Large
Basic Aerodynamics Ii Stability Large
 
EASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICS
EASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICSEASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICS
EASA PART-66 MODULE 8.4 : FLIGHT STABILITY AND DYNAMICS
 
Theory of flight final
Theory of flight finalTheory of flight final
Theory of flight final
 
Aircraft fuel system
Aircraft fuel systemAircraft fuel system
Aircraft fuel system
 
Aircraft ctrl systems
Aircraft ctrl systemsAircraft ctrl systems
Aircraft ctrl systems
 
Aircraft Systems and Instruments
Aircraft Systems and InstrumentsAircraft Systems and Instruments
Aircraft Systems and Instruments
 
Fixed wing aircrafts power point presentation
Fixed wing aircrafts power point presentationFixed wing aircrafts power point presentation
Fixed wing aircrafts power point presentation
 
EASA PART-66 MODULE 8.2 : AERODYNAMICS
EASA PART-66 MODULE 8.2 : AERODYNAMICSEASA PART-66 MODULE 8.2 : AERODYNAMICS
EASA PART-66 MODULE 8.2 : AERODYNAMICS
 

Andere mochten auch

Aircraft Engine part1
Aircraft Engine part1Aircraft Engine part1
Aircraft Engine part1Omar Osama
 
Avp 3 Aircraft Engines
Avp 3   Aircraft Engines Avp 3   Aircraft Engines
Avp 3 Aircraft Engines oldcramo2009
 
best ppt on jet engines
best ppt on jet enginesbest ppt on jet engines
best ppt on jet enginesDeepak Kumar
 
Aircraft propulsion (5)
Aircraft propulsion (5)Aircraft propulsion (5)
Aircraft propulsion (5)Priyank Peter
 
Types of jet propulsion engine
Types of jet propulsion engineTypes of jet propulsion engine
Types of jet propulsion engineMal Mai
 
PROJECT_GAS_TURBINE_ENGINE
PROJECT_GAS_TURBINE_ENGINEPROJECT_GAS_TURBINE_ENGINE
PROJECT_GAS_TURBINE_ENGINEDevendra Hembade
 
Piston Engines: Cooling
Piston Engines: CoolingPiston Engines: Cooling
Piston Engines: CoolingJess Peters
 
JET ENGINE PPT BY SANDEEP YADAV
JET ENGINE PPT BY SANDEEP YADAVJET ENGINE PPT BY SANDEEP YADAV
JET ENGINE PPT BY SANDEEP YADAVSANDEEP YADAV
 
Turbine engine 1
Turbine engine 1Turbine engine 1
Turbine engine 1Zaib Amjad
 
turbine engine intake
 turbine engine intake turbine engine intake
turbine engine intakeradhebharvad
 
Gas turbine and Jet Propulsion
Gas turbine and Jet PropulsionGas turbine and Jet Propulsion
Gas turbine and Jet PropulsionChinmay Paranjpe
 
LANDING GEAR FOR AIRCRAFT
LANDING GEAR FOR AIRCRAFTLANDING GEAR FOR AIRCRAFT
LANDING GEAR FOR AIRCRAFTBai Haqi
 
IAEA 2nd Aircraft Engine World China Summit 101812
IAEA  2nd Aircraft Engine World China Summit 101812IAEA  2nd Aircraft Engine World China Summit 101812
IAEA 2nd Aircraft Engine World China Summit 101812rezaeiho
 
Finite element analysis of engine mounting bracket by considering pretension ...
Finite element analysis of engine mounting bracket by considering pretension ...Finite element analysis of engine mounting bracket by considering pretension ...
Finite element analysis of engine mounting bracket by considering pretension ...eSAT Journals
 
How Engine Mount Affect The Engine
How Engine Mount Affect The EngineHow Engine Mount Affect The Engine
How Engine Mount Affect The EngineHarmony Motor Works
 

Andere mochten auch (20)

Aircraft Engine part1
Aircraft Engine part1Aircraft Engine part1
Aircraft Engine part1
 
Avp 3 Aircraft Engines
Avp 3   Aircraft Engines Avp 3   Aircraft Engines
Avp 3 Aircraft Engines
 
best ppt on jet engines
best ppt on jet enginesbest ppt on jet engines
best ppt on jet engines
 
V2500 lbm issue 01
V2500 lbm issue 01 V2500 lbm issue 01
V2500 lbm issue 01
 
Aircraft propulsion (5)
Aircraft propulsion (5)Aircraft propulsion (5)
Aircraft propulsion (5)
 
Types of jet propulsion engine
Types of jet propulsion engineTypes of jet propulsion engine
Types of jet propulsion engine
 
Jet engines
Jet enginesJet engines
Jet engines
 
PROJECT_GAS_TURBINE_ENGINE
PROJECT_GAS_TURBINE_ENGINEPROJECT_GAS_TURBINE_ENGINE
PROJECT_GAS_TURBINE_ENGINE
 
Piston Engines: Cooling
Piston Engines: CoolingPiston Engines: Cooling
Piston Engines: Cooling
 
Landing gear
Landing gearLanding gear
Landing gear
 
JET ENGINE PPT BY SANDEEP YADAV
JET ENGINE PPT BY SANDEEP YADAVJET ENGINE PPT BY SANDEEP YADAV
JET ENGINE PPT BY SANDEEP YADAV
 
Turbine engine 1
Turbine engine 1Turbine engine 1
Turbine engine 1
 
JET ENGINE BASIC
JET ENGINE BASICJET ENGINE BASIC
JET ENGINE BASIC
 
turbine engine intake
 turbine engine intake turbine engine intake
turbine engine intake
 
Gas turbine and Jet Propulsion
Gas turbine and Jet PropulsionGas turbine and Jet Propulsion
Gas turbine and Jet Propulsion
 
LANDING GEAR FOR AIRCRAFT
LANDING GEAR FOR AIRCRAFTLANDING GEAR FOR AIRCRAFT
LANDING GEAR FOR AIRCRAFT
 
IAEA 2nd Aircraft Engine World China Summit 101812
IAEA  2nd Aircraft Engine World China Summit 101812IAEA  2nd Aircraft Engine World China Summit 101812
IAEA 2nd Aircraft Engine World China Summit 101812
 
Finite element analysis of engine mounting bracket by considering pretension ...
Finite element analysis of engine mounting bracket by considering pretension ...Finite element analysis of engine mounting bracket by considering pretension ...
Finite element analysis of engine mounting bracket by considering pretension ...
 
ADS-B presentation
ADS-B presentationADS-B presentation
ADS-B presentation
 
How Engine Mount Affect The Engine
How Engine Mount Affect The EngineHow Engine Mount Affect The Engine
How Engine Mount Affect The Engine
 

Ähnlich wie Aircraft Engine

Diesel enginecomponents
Diesel enginecomponentsDiesel enginecomponents
Diesel enginecomponentsKrishna Gali
 
Internal Combustion Engines - Variable valve lift
Internal Combustion Engines - Variable valve liftInternal Combustion Engines - Variable valve lift
Internal Combustion Engines - Variable valve liftRa'uf Tailony
 
4 stroke cycle engine operations
4 stroke cycle engine operations4 stroke cycle engine operations
4 stroke cycle engine operationsreymartyvette_0611
 
Lec 7 ME-439 ICE Lec -7_Turbocharging.pptx
Lec 7 ME-439 ICE Lec -7_Turbocharging.pptxLec 7 ME-439 ICE Lec -7_Turbocharging.pptx
Lec 7 ME-439 ICE Lec -7_Turbocharging.pptxabdurrafaykhokhars
 
SI_Engines is an engine which converts chemical energy of fuel to mechanical...
SI_Engines is an engine which converts chemical energy of  fuel to mechanical...SI_Engines is an engine which converts chemical energy of  fuel to mechanical...
SI_Engines is an engine which converts chemical energy of fuel to mechanical...RahitaMalik
 
SI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxx
SI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxxSI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxx
SI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxxGanesharjunS
 
Si engines.ppt naphis
Si engines.ppt naphisSi engines.ppt naphis
Si engines.ppt naphisnaphis ahamad
 
Si engines.ppt naphis converted
Si engines.ppt naphis convertedSi engines.ppt naphis converted
Si engines.ppt naphis convertednaphis ahamad
 
siengines-200109095607 (1).pptx
siengines-200109095607 (1).pptxsiengines-200109095607 (1).pptx
siengines-200109095607 (1).pptxVirrrr1
 
chaptrno-140114211033-phpapp02.pptx
chaptrno-140114211033-phpapp02.pptxchaptrno-140114211033-phpapp02.pptx
chaptrno-140114211033-phpapp02.pptxprabhakarjha82
 
Deg presentation
Deg presentationDeg presentation
Deg presentationasif.rajput
 
VCR ENGINE PROJECT PART 2
VCR ENGINE PROJECT PART 2VCR ENGINE PROJECT PART 2
VCR ENGINE PROJECT PART 2MILAN HAZRA
 

Ähnlich wie Aircraft Engine (20)

Diesel enginecomponents
Diesel enginecomponentsDiesel enginecomponents
Diesel enginecomponents
 
Lesson6 diesel enginecomponents
Lesson6 diesel enginecomponentsLesson6 diesel enginecomponents
Lesson6 diesel enginecomponents
 
Internal Combustion Engines - Variable valve lift
Internal Combustion Engines - Variable valve liftInternal Combustion Engines - Variable valve lift
Internal Combustion Engines - Variable valve lift
 
AEROSPACE
AEROSPACEAEROSPACE
AEROSPACE
 
4 stroke cycle engine operations
4 stroke cycle engine operations4 stroke cycle engine operations
4 stroke cycle engine operations
 
Lec 7 ME-439 ICE Lec -7_Turbocharging.pptx
Lec 7 ME-439 ICE Lec -7_Turbocharging.pptxLec 7 ME-439 ICE Lec -7_Turbocharging.pptx
Lec 7 ME-439 ICE Lec -7_Turbocharging.pptx
 
AUTOMOBILE ENGINEERING.pptx
AUTOMOBILE ENGINEERING.pptxAUTOMOBILE ENGINEERING.pptx
AUTOMOBILE ENGINEERING.pptx
 
SI_Engines is an engine which converts chemical energy of fuel to mechanical...
SI_Engines is an engine which converts chemical energy of  fuel to mechanical...SI_Engines is an engine which converts chemical energy of  fuel to mechanical...
SI_Engines is an engine which converts chemical energy of fuel to mechanical...
 
SI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxx
SI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxxSI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxx
SI_ENhc8tc6ff6c6c66f5c5c5GINES.PPTCTC I I xtxxx
 
Unit i
Unit iUnit i
Unit i
 
Si engines.ppt naphis
Si engines.ppt naphisSi engines.ppt naphis
Si engines.ppt naphis
 
I c engine
I c engine I c engine
I c engine
 
Si engines.ppt naphis converted
Si engines.ppt naphis convertedSi engines.ppt naphis converted
Si engines.ppt naphis converted
 
siengines-200109095607 (1).pptx
siengines-200109095607 (1).pptxsiengines-200109095607 (1).pptx
siengines-200109095607 (1).pptx
 
Ch06
Ch06Ch06
Ch06
 
chaptrno-140114211033-phpapp02.pptx
chaptrno-140114211033-phpapp02.pptxchaptrno-140114211033-phpapp02.pptx
chaptrno-140114211033-phpapp02.pptx
 
4 stroke cycle engine operations
4 stroke cycle engine operations4 stroke cycle engine operations
4 stroke cycle engine operations
 
Deg presentation
Deg presentationDeg presentation
Deg presentation
 
VCR ENGINE PROJECT PART 2
VCR ENGINE PROJECT PART 2VCR ENGINE PROJECT PART 2
VCR ENGINE PROJECT PART 2
 
Heat Engine
Heat Engine Heat Engine
Heat Engine
 

Kürzlich hochgeladen

Philosophy of Education and Educational Philosophy
Philosophy of Education  and Educational PhilosophyPhilosophy of Education  and Educational Philosophy
Philosophy of Education and Educational PhilosophyShuvankar Madhu
 
Prescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptxPrescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptxraviapr7
 
HED Office Sohayok Exam Question Solution 2023.pdf
HED Office Sohayok Exam Question Solution 2023.pdfHED Office Sohayok Exam Question Solution 2023.pdf
HED Office Sohayok Exam Question Solution 2023.pdfMohonDas
 
Presentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a ParagraphPresentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a ParagraphNetziValdelomar1
 
Quality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICEQuality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICESayali Powar
 
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptxClinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptxraviapr7
 
AUDIENCE THEORY -- FANDOM -- JENKINS.pptx
AUDIENCE THEORY -- FANDOM -- JENKINS.pptxAUDIENCE THEORY -- FANDOM -- JENKINS.pptx
AUDIENCE THEORY -- FANDOM -- JENKINS.pptxiammrhaywood
 
The basics of sentences session 10pptx.pptx
The basics of sentences session 10pptx.pptxThe basics of sentences session 10pptx.pptx
The basics of sentences session 10pptx.pptxheathfieldcps1
 
How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17Celine George
 
How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17Celine George
 
Diploma in Nursing Admission Test Question Solution 2023.pdf
Diploma in Nursing Admission Test Question Solution 2023.pdfDiploma in Nursing Admission Test Question Solution 2023.pdf
Diploma in Nursing Admission Test Question Solution 2023.pdfMohonDas
 
How to Make a Field read-only in Odoo 17
How to Make a Field read-only in Odoo 17How to Make a Field read-only in Odoo 17
How to Make a Field read-only in Odoo 17Celine George
 
In - Vivo and In - Vitro Correlation.pptx
In - Vivo and In - Vitro Correlation.pptxIn - Vivo and In - Vitro Correlation.pptx
In - Vivo and In - Vitro Correlation.pptxAditiChauhan701637
 
UKCGE Parental Leave Discussion March 2024
UKCGE Parental Leave Discussion March 2024UKCGE Parental Leave Discussion March 2024
UKCGE Parental Leave Discussion March 2024UKCGE
 
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptxPractical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptxKatherine Villaluna
 
5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...CaraSkikne1
 
CAULIFLOWER BREEDING 1 Parmar pptx
CAULIFLOWER BREEDING 1 Parmar pptxCAULIFLOWER BREEDING 1 Parmar pptx
CAULIFLOWER BREEDING 1 Parmar pptxSaurabhParmar42
 
Education and training program in the hospital APR.pptx
Education and training program in the hospital APR.pptxEducation and training program in the hospital APR.pptx
Education and training program in the hospital APR.pptxraviapr7
 
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptxSandy Millin
 

Kürzlich hochgeladen (20)

Prelims of Kant get Marx 2.0: a general politics quiz
Prelims of Kant get Marx 2.0: a general politics quizPrelims of Kant get Marx 2.0: a general politics quiz
Prelims of Kant get Marx 2.0: a general politics quiz
 
Philosophy of Education and Educational Philosophy
Philosophy of Education  and Educational PhilosophyPhilosophy of Education  and Educational Philosophy
Philosophy of Education and Educational Philosophy
 
Prescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptxPrescribed medication order and communication skills.pptx
Prescribed medication order and communication skills.pptx
 
HED Office Sohayok Exam Question Solution 2023.pdf
HED Office Sohayok Exam Question Solution 2023.pdfHED Office Sohayok Exam Question Solution 2023.pdf
HED Office Sohayok Exam Question Solution 2023.pdf
 
Presentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a ParagraphPresentation on the Basics of Writing. Writing a Paragraph
Presentation on the Basics of Writing. Writing a Paragraph
 
Quality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICEQuality Assurance_GOOD LABORATORY PRACTICE
Quality Assurance_GOOD LABORATORY PRACTICE
 
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptxClinical Pharmacy  Introduction to Clinical Pharmacy, Concept of clinical pptx
Clinical Pharmacy Introduction to Clinical Pharmacy, Concept of clinical pptx
 
AUDIENCE THEORY -- FANDOM -- JENKINS.pptx
AUDIENCE THEORY -- FANDOM -- JENKINS.pptxAUDIENCE THEORY -- FANDOM -- JENKINS.pptx
AUDIENCE THEORY -- FANDOM -- JENKINS.pptx
 
The basics of sentences session 10pptx.pptx
The basics of sentences session 10pptx.pptxThe basics of sentences session 10pptx.pptx
The basics of sentences session 10pptx.pptx
 
How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17How to Show Error_Warning Messages in Odoo 17
How to Show Error_Warning Messages in Odoo 17
 
How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17How to Add Existing Field in One2Many Tree View in Odoo 17
How to Add Existing Field in One2Many Tree View in Odoo 17
 
Diploma in Nursing Admission Test Question Solution 2023.pdf
Diploma in Nursing Admission Test Question Solution 2023.pdfDiploma in Nursing Admission Test Question Solution 2023.pdf
Diploma in Nursing Admission Test Question Solution 2023.pdf
 
How to Make a Field read-only in Odoo 17
How to Make a Field read-only in Odoo 17How to Make a Field read-only in Odoo 17
How to Make a Field read-only in Odoo 17
 
In - Vivo and In - Vitro Correlation.pptx
In - Vivo and In - Vitro Correlation.pptxIn - Vivo and In - Vitro Correlation.pptx
In - Vivo and In - Vitro Correlation.pptx
 
UKCGE Parental Leave Discussion March 2024
UKCGE Parental Leave Discussion March 2024UKCGE Parental Leave Discussion March 2024
UKCGE Parental Leave Discussion March 2024
 
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptxPractical Research 1: Lesson 8 Writing the Thesis Statement.pptx
Practical Research 1: Lesson 8 Writing the Thesis Statement.pptx
 
5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...5 charts on South Africa as a source country for international student recrui...
5 charts on South Africa as a source country for international student recrui...
 
CAULIFLOWER BREEDING 1 Parmar pptx
CAULIFLOWER BREEDING 1 Parmar pptxCAULIFLOWER BREEDING 1 Parmar pptx
CAULIFLOWER BREEDING 1 Parmar pptx
 
Education and training program in the hospital APR.pptx
Education and training program in the hospital APR.pptxEducation and training program in the hospital APR.pptx
Education and training program in the hospital APR.pptx
 
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
2024.03.23 What do successful readers do - Sandy Millin for PARK.pptx
 

Aircraft Engine

  • 1. ATA Number ATA Chapter name ATA 71 POWER PLANT ATA 72 ENGINE CONSTRUCTION ATA 73 FUEL AND CONTROL ATA 74 IGNITION ATA 75 AIR SYSTEM ATA 76 CONTROLS ATA 77 INDICATING ATA 78 THRUST REVERSER ATA 79 OIL SYSTEM ATA 80 STARTING ENGINE ATA CHAPTERS
  • 2. Engine Specification EPR Engine Thrust EGT Limit [margin] SFC Engine Weight Power Plant Weight Fan diameter T Flat (ISA + 15 ) By-Pass ratio [1:5] CPR Number of rotors , speeds [N1, N2,…] Speed limits [N1,N2,N3] Thrust setting parameter [ EPR , N1 ] Mechanical standards/ arrangements Gearbox location [ core/fan mounted] Direction of rotation
  • 10. The cowls enclose the periphery of the engine so as to form the engine nacelle, underneath the aircraft wings. The nacelle is the aerodynamic structure around the basic engine and has several purposes: - To smooth the airflow around and into the engine, in order to decrease drag and give better engine performance. - To prevent damage to the external surface of the engine. - To give extra strength to the engine structure. - To make connections for air, fluids and electricity. - To enable access to the engine, or direct access to some engine equipment Power Plant
  • 11. Air Inlet Cowl  The air inlet cowl is at the forward section of the nacelle Attached on its rear flange to the engine fan case. Provides a smooth airflow into the engine during all aircraft operational sequences Prevents ice formation at the front of the power plant. Has an anti-ice inlet duct, an interphone connector and jack and also houses the Temp. sensor.
  • 12.  The fan cowl doors Are manually opened, or closed, and can be held open for engine maintenance purposes. Each fan cowl door contains three hoist points and two telescopic hold-open rods which support the doors in the open position. There are two hold-open positions, 20° and 55°. The 20° position allows access to the lower part of the fan compartment for maintenance of accessory gearbox components (IDG, hydraulic pump, fuel module, oil system). The 55° maximum open position allows access to all equipment located in the fan compartment. One cowl door provides direct access to the starter valve, and the other provides direct access to the oil tank. Have three hook type latches on the right hand door which mate with adjustable eye bolts on the left hand door. Index pins provide door positioning at each latch. The latch handle closing pressure is adjusted with the fan cowl doors closed. Fan Cowl
  • 13.  The thrust reverser Is located between the engine fan cowls and the exhaust nozzle, and comprises two cowls. Each cowl is hinged at the top to the pylon and latched to the other along the bottom centerline. In the stow position, the thrust reverser assembly forms the passage for fan secondary airflow to be discharged overboard. In the deploy position (reverse thrust mode), four hydraulically actuated pivoting doors redirect the secondary airflow forward and provide a braking effect to reduce the aircraft stopping distance. Designed for ground operation only. A hydraulically actuated cowl opening system allows each thrust reverser cowl to be opened independently  The mechanical structure includes: - An outer cowl, which forms the fan discharge flow outer contour. - An inner cowl, which forms the fan flow inner contour, and engine outer envelope. - Pivoting doors going into the fan stream, blocking and redirecting the secondary airflow outward and forward.  The C-ducts consist of: - The outer cowl, or fan outer contour, which is part of the mixed flow nacelle design and which, in the stowed position, encloses the pivoting doors. - Four hinges which attach the cowl to the pylon. These hinges are an integral part of a machined aluminum beam which runs along the upper portion of the thrust reverser. - Two hoist points on each outer cowl for removal/ installation maintenance operations. - Five tension hook latches, which are installed at the bottom of the left hand side outer cowl. - A “J” flange, at the aft end of the cowl, which mates with the “V” groove of the exhaust nozzle. - A pressure relief door, located at the bottom, which prevents permanent structural deformation in the event of single bleed duct rupture. Thrust Reverser Cowl
  • 14.  The CAN Collects the cool bypass airflow, the hot core exhaust gases and bleed air flows. The cool air and hot gases mix and exhaust to atmosphere through a final nozzle. An interchangeable assembly that has an acoustic outer duct assembly made of graphite/epoxy. It is held by six aerodynamic metal struts attached to the inner duct assembly. Is attached directly on to the LP turbine module of the engine. Common Nozzle
  • 15. Engine Mounts Front Mounts  The engine mounts support the weight of the engine and transmit loads to the aircraft structure through the pylon.  The front mount Attached at the top of the intermediate case. The engine front mount transmits engine thrust, side and vertical loads to the aircraft pylon. The thrust and side loads are transmitted from the intermediate case through a split spherical bearing – which is mounted on the intermediate case - to the cylindrical trunnion. These loads are now transmitted through the main attachment bracket to the aircraft pylon. The vertical loads are transmitted from the intermediate case through the vertical load links to the vertical load support beam. They are then transmitted through the front horizontal trunnion to the main attachment bracket to the aircraft pylon. The main attachment bracket is in two halves to give more than one route for the thrust and side loads. If there is a failure of a primary component that affects the vertical loading the engine would drop and the fail safe catcher link would contact the rear trunnion (on the main attachment bracket) and support the vertical loads.
  • 16. Engine Mounts Rear Mounts  The rear mount Is attached at the top of the exhaust case. The engine rear mount transmits engine torque loads, vertical loads and side loads to the aircraft pylon.
  • 18. Engine Construction Air Intake Air Intake Design Requirements  The air intake should be able to.: Admit the maximum amount of air. Diffuser : Deliver the air to compressor with max Mach no. = 0.5 Mach Produce little aerodynamics drag. Reduce level of noise by engine.  The main causes of losses are generally the result of:- poor sheet metal work, e.g. bad riveting, Dents, scores and scratches, Misalignment due to incorrect assembly. Take care, the intake is a very important part.  Inlet cone: Streaming for air. Anti-ice [ vibration – Hot air ]. Eagle eye : Scare birds.
  • 19. Engine Construction Compressor Function o Increase the air mass flow o Improve combustion characteristics o Increase the efficiency of operating cycle o Increase the thrust produced by engine o Improve fuel economy o Assist in the provision of a small and compact engine. Principle o Rotating parts :Increase velocity [add kinetic energy to air]. o Static parts [diffusion]: reduce velocity & convert kinetic energy to pressure energy. Components Rotor Blades Drum or Disk (Drum = more than one Disk) Shaft Stator Vanes Casing Seal Attachment of rotor blades Solid root Fir tree root Dovetail root (Axial root - Radial root) Radial (Centrifugal) Devices – Can not handle as high mass flow – Less efficient than axial device – Short length – Robust – Less Parts Axial Devices – High mass flow – High efficiency – Stackable (multi-staging) – More parts – More complex TWO PRIMARY TYPES OF COMPRESSORS Twisted blade design Root speed (vf) = Π Dr N As diameter increase, angle of attack increase, so rotation speed increase. Tip speed (vf) = Π Dt N/60 Root speed (vf) = Π Dt N/60 SO blades are made twisted, To fast speed recovery so prevent stall
  • 20. Stall & Surge: Compressor Surge [ result from stall ] occurs when the inlet flow reduces than certain limit, which leads to flow reversal. Compressor stall [ start at blades ] occurs when the pressure at down stream of compressor is greater than the compressor discharge pressure which leads to no discharge from compressor. Causes: Surge induced by inlet air flow distortion ( high cross wind, sharp, uncoordinated aircraft maneuvers, intake problem ). Shear/Side Wind : cause changes in inlet air mass. FOD [Foreign object damage]. Sudden acceleration and sudden deceleration. Excessive increase in combustion chamber pressure caused by rapid opening of the throttle particularly at low engine RPM. Indications : Unexpected loss of thrust. Abnormal engine noises and vibrations. Un-commanded variations in engine RPM. Rapid increase in EGT. In extreme cases the reversal of airflow can result in the ejection of exhaust gasses out of the air intake. Transient conditions: ( At which surge occur ) 1. Rapid acceleration 2. Rapid deceleration 3. Starting [similar to Rapid acceleration ] Rapid acceleration Thrust lever ↑ ↑ Fuel ↑ HPT blade speed ↑ HPC blade speed ↑ Angle of attack α ↑ air speed HPC Surge (Front Stages) Rapid deceleration Thrust lever ↓ ↓ Fuel ↓ HPT blade speed HPC output air mass same as it HPT takes only accepted air mass relative to rotation speed Back pressure due to rest of air mass HPC Surge ( Rear Stages)
  • 21. Function: o Separate two rolling elements. o Minimize friction loss. Bearings reduce friction by providing smooth metal balls or rollers, and a smooth inner and outer metal surface for the balls to roll against. These balls or rollers "bear" the load, allowing the device to spin smoothly. Bearing loads o Radial load (weight load) o Axial load [thrust load] Roller bearing • Large contact area so hold heavy radial loads. • High load carrying capacity • Allow thermal expansion • Mostly used at hot section (shaft end ) Ball bearing (Thrust Bearing) • Can handle both radial and thrust loads. • Lower load carrying capacity, higher speed. • Mostly used at cold section (shaft start) : o Do not allow thermal expansion o Location bearing : to prevent shaft and fan from moving forward OIL SYSTEM Bearing
  • 22. Seals The prime purpose is to prevent leakage at a joint, or it may also help to prevent the ingress of foreign matter into system. O-ring Seal • Work under pressure. • Usage one time only. Labyrinth Seal • Most common • Use shock theory • High oil consumption Carbon Seal • Very sensitive to pressure and temperature. • Usually used in bearing oil seal. Brush Seal Hydraulic Seal Screw back Seal Troubleshooting • Higher than normal oil consumption. • Higher breather air pressure. • Dirty inefficient compressor • Distorted or burnet nozzle guide vanes or turbines. • Higher fuel consumption. • Higher than normal turbine gas temperature. • A decrease in engine performance.
  • 23. The bearing sump philosophy • 1st room to prevent oil spillage on other part. • 2nd room to prevent oil leakage from oil seal due to high oil pressure. • Also cooling oil, and maintain 1st room pressure within limits. • Vent (breather air): to eject air enter 1st room through oil seal. • Restrictor : installed on vent to equalize 1st and 2nd rooms pressure. • Inspection from drain : o High pressure oil seal leakage. o Low pressure air seal leakage. The bearing sump
  • 24. Engine Construction Combustion Chamber Function • Complete combustion • Contain flame • Convert air and fuel mix to hot gases • Combustion chamber walls coating • Complete burning to prevent back fire Components • Outer case • Outer liner • diffuse • Inner liner – around inner case • Inner case – around shaft Operation • 18% Primary air o 10% Enters at the snout (mixed with fuel to start ignition – direct mix through swirling) o 8% Enters the primary zone through the walls of the combustion chamber (contain flame – more mixing ) • 10% Secondary air – turbo flow - o Provide cooling air on either side of the liner. o Complete combustion and increase vortex –turbulence to prevent flame propagation and improve combustion. • 72% Tertiary air • Dilution: Provide cooling air on either side of the liner. • Prevent flame propagation . Cane-Annular Design • Lighter weight • Flame out recovery by interconnection • Residual fuel drain to prevent choke at starting . • Residual fuel drain operate by pressure valve depend on C.C pressure. Cane Design Thicker structure x Longer structure Annular Design • inner and outer case, • Inner and outer liner • One C.C • Short structure Annular Design • SAC : Single Annular Combustion o One flame outlet – nozzle- • DAC : Dual Annular Combustion o Two flame outlet – nozzle Near C.C liner short life liner Low emission Better combustion Ignition • More than one igniter on C.C to alternately operate. • Igniter only work at starting Intel steady state flame condition. Incomplete combustion result : due to ineffective swirl, fuel particles stake at turbine blades making hot spots. At starting hot spots burn and increase blade temperature which lead to remove coating above blades. Notes • Combustion chamber shape like diffuser -flame stability - to lower speed of air coming from compressor to prevent flame off. • C.C. Pressure reduced due to turbulence inside . • CDP compressor discharge pressure PB burner pressure . • Pressure of C.C. change at transient condition. • Highest thermal stress at takeoff. • 1:15 optimum combustion efficiency • Actual combustion efficiency [45:1 130:1 ]
  • 25. Engine Construction Turbine Function The turbine converts most of the heat and kinetic energy generated by combustion section into mechanical work using expansion. Types by number of spools • Single Spool Turbine • Twin Spool Turbine • Triple Spool Turbine Design Casing shape like diffuser : to contain flow expansion And to take same power from flow. because power reduced due to flow expansion. So larger blade will make same flow mass push blades to take same power. Area between vanes shape as nozzle: To reduce flow pressure & temperature and increase velocity. In one word : Flow Expansion Components NGV’s • Turbine nozzle guide vane • Function : to increase the velocity of the gas stream and direct it at the optimum angle of attack on to the turbine blades. • Flow Temp, Pressure ↓ Velocity ↑ Blades • Blade (fir tree root) To allow thermal expansion and rigidity • Blade (twisted) To stabilize flow velocity with diameter variation • No drum – no welding – in turbine : Disks fixed using bolts. • Blade tip: o Easy to broke by F.O.D to protect case. o Anti-corrosion surface. • Material [ Mono crystal – Ceramic ] Shroud Protect case via clearance [ 8% 3.5% losses ] Sealing to prevent flow leakage Cold to perfectly close at blades Segment : group of vanes Impulse type A stator vane and rotor blade arrangement whereby the vanes form convergent ducts and the blades form straight ducts. The rotor is then turned by impulse as gases impinge on the blades. o [ Rotor → Power ] o Usually used in LPT Reaction type Produces rotation by the aerodynamic action of the air as it accelerates between the blades. The reaction to the force generated by the accelerated air causes the turbine to rotate. o [ Rotor → Nozzle → Expansionpower ] Impulse/Reaction type A stator vane and rotor blade arrangement whereby : the base area is an impulse - low flow velocity - the tip is a reaction design - high flow velocity – to reduce it Turbine Types
  • 26. Engine Construction Exhaust system Functions •Accelerate hot gases to increase thrust. [Diffuser shape] • Clear exhaust gases to prevent back pressure. Components 1. Exhaust Nozzle [ Flow acceleration & expansion ] 2. Propelling nozzle [ Secondary Flow streaming guiding ] 3. Exhaust cone (plug) - Stop turbulence - primary Flow streaming guiding - Protect disks and bearing Duct Types Mixed flow design Reduce Noise Duct Types Non mixed flow design Problems •Drag on inner surface •Noisy
  • 28. Fuel & Control EEC DADC TMC COCKPIT DISPLAY ENGINE TLA To Po POWER SOURCE To Po PLA METERED FUEL FLOW SIGNAL TORQUE MOTOR DRIVE FAIL/FAIXED SLONIOD METERING VALVE FEEDBACK ENGINE SPEED FCU Computing Section Metering Section CDP LIMITER Speed Controller 3D CAM Main Filter Regulating Valve FMU FFT Shut off valve CDP CDP N2 SPEED CIT To , Po Trim Adj Cut off switch Servo Filter Servo Supply Operate (sensor/valves) Cooling Lubricant Low Pressure Pump Fuel Heater & Filter High Pressure Pump Return to HPP Fault Monitor
  • 29. Fuel & Control Low Pressure Pump Fuel Heater High Pressure Pump Fuel Control Unit Fuel Flow Transmitter Fuel Cooled Cooler Flow Divider Fuel Nozzle Ensures an adequate 'head of pressure' at the inlet to the pump preventing cavitations of the pump during normal operation. Ensures that any ice particles are removed from the fuel before the fuel reaches the Fuel Control Unit (FCU). Hot air for heating the fuel is drawn from the engine compressor. Connected with the LPP by a shaft have a weak point to shear in case of pump failure to protect the G.B Meters and supplies the correct amount of fuel to the engine burners depending upon throttle position and the various environmental conditions Indicates to the flight deck crew the amount of fuel flowing from the fuel control unit to the engine. Although part of the fuel system has a primary function to cool the oil from the engine lubricating system. The cold fuel cools the oil and at the same time the oil heats the fuel. Directs the fuel flow to either the primary or the secondary fuel nozzles. The function of the nozzle is to inject fuel into the combustor chamber in a highly atomized form, which aids the combustion of the fuel Externally mounted, Internally mounted Variable Disp. Piston type Constant Disp. With relief valve SIMPLEX : only a single manifold supply is required Duplex : is usually associated with a dual flow manifold, which receives both secondary and primary fuel flow.
  • 30. Thrust Management Computer Fault monitor Fuel Control Unit Electronic Engine Control Computer Metered Fuel Although not part of the fuel metering system, it allows the flight crew to select a thrust setting in flight, i.e., climb, cruise, take-off, etc. It also displays, on the flight deck, the maximum engine speed for a given thrust setting Stores fault information from the electronic engine control unit. Meters and computes the fuel flow to the engine, a hydro mechanical computer. Controls the engine speed to suit the pressure and temperature conditions of the day. The fuel from the FCU to the aircraft is fuel which has been metered to enable the engine to produce the correct amount of thrust for a given condition and throttle lever position. Fuel & Control Electronic Engine Control Digital Air Data Computer The primary purpose of an electronic engine control system is to reduce the pilot's work load by computing, displaying and maintaining the selected engine settings as a function of external sensors and selected flight modes. The primary source of pressure and temperature sensing. This information is passed to the thrust management and the electronic the primary source of pressure and temperature sensing. This information is passed to the thrust management and the electronic engine control computers.
  • 32. IGNITION The ignition sequence is cancelled when the starter cycle is cancelled. to provide a very high voltage to jump a wide igniter plug spark gap, and also, a high intensity spark. The high energy capacitor type ignition system has been fitted to gas turbine engines since it provides both a high voltage and an exceptionally hot spark over the area of the spark gap. Thus the chances of igniting the fuel/air mixture are assured at reasonably high altitudes.
  • 34. Function • Stability Bleed : stall and surge prevention devices o VSV Variable Stator Vane (MODULATED) o Usage : to stop stall –angle of attack change or m - occur in first stages in HPC when rapid acceleration condition applied. o Operation : actuator controlled via EEC – after sensing temp and pressure. o Always Synchronized with VBV . o Failsafe : fully open o Worth case : take off fully opened Surge o Hydraulically or pneumatically operated – using fuel • Easy to get rid of it, if any problem happened because there is a lot of fuel. • To prevent stress on oil maintain oil viscosity • To let EEC fully control Valves • To reduce interfaces between airplane and engine o Electrically controlled o VBV Variable Bleed Valve ( ) o Usage : to stop surge if air accumulation occur between LPC & HPC when rapid deceleration condition applied via ventilation. o Operation : master valve controlled via EEC, slave valves follow . o Hydraulically or pneumatically operated – using fuel- . o Electrically controlled. o Failsafe : fully open o Worth case : STUCK OPEN EGT ↑ Powerless Surge o SBV Surge Bleed Valve ( ) o Usage : to stop surge if air accumulation occur in rear HPC stages via ventilation. o Operation : fully open or fully closed . o Pneumatically operated – using fuel- . o Spring loaded o Failsafe : fully open • Service Bleed o Sealing Oil sump o Cooling • Turbine Blades & Vanes • HPT Shroud Cooling | Outside/Inside • LPT Case Cooling Low loads @ cruise Low temp Turbine blades High tip clearance Cold air @case Case shrink lower clearance o ACC Active Clearance Control o TCC Turbine Case Cooling Engine Core | Hot air from turbine compressor blade cooling[heating] compressor blades stretching lower clearance Rigging o Only for VSV, VBV. o To check valve condition at fully open/close selection. o Recover EGT margin due to valve not fully closed. Air System Cooling o Inlet guide vane: internal cooling. o HPT: internal cooling. o LPT: external cooling.
  • 36. Function • Lubrication • Cooling Oil System Main components • Hot Tank (because it’s before cooler ) Function: o Store oil o Provide continuous oil supply Material : o Aluminum alloy o Stainless steel o Composite material Components: o Deaerator (separate AIR from oil) o Breather (separate OIL from air) o Pump o Oil filter o Oil cooler o Chip detector • Types : master Chip detector + slaves Chip detector • On scavenge line after user and before pump • Heat management ( to control oil temp. ) o ACOC AOHE Air Cold Oil Cooler o FCOC FOHE Fuel Cold Oil Cooler • Supply line • Scavenge line and pumps ( recalculate oil) • Pressure relive valve • Chip detector • Breather -vent- (separate OIL from air) • Deaerator (separate AIR from oil) • ΔP Switch : Pressure relive valve/over pressure detector Design wise Oil can leak into fuel because it’s higher pressure, why? o oil properties can’t effect fuel o oil can burn with fuel Aircraft oil different from cars oil, why? o In aircraft : running condition easier – no metal to metal friction o In cars : metal to metal friction – harder running condition Oil Service Aircraft engine oil change only if: o Store engine o Contamination o Manufacture order Aircraft engine oil level check: After 10 min exactly – not more than 30 min – after engine shutdown? To allow level of oil settle down in the tank after deaeration