Water purifier GWPDAURUM40000.pdf

AQUAGUARD®
AURA
AURA
Product installation should be done only by a trained Eureka Forbes Service Technician only.
1. Input water must be tested for Total Dissolved Solids (TDS) and Total Hardness
- Install the product in a dry ventilated place. Keep it away from direct sunlight, heating devices or areas below 10oC.
- The purifier should be placed in area which is free of ants/insects/other pests.
- Ensure that the input tap water temperature is in the range of 10o - 40oC.Avoid installation to a hot water tap as it can damage the filters.
2. The input water pressure to your water purifier should be within the recommended range (refer variant specific technical specifications table). If
the input water pressure is more than specified, installation of a PRV (Pressure Regulating Valve)** is mandatory. If the input water pressure is
less than specified, installation of an external booster pump** is recommended.
3. Ensure that the filters are flushed thoroughly and independently for 3-5 minutes to remove fine particles present in the filter, before the installation
of the unit.
4. After installation, run the purifier for 5-10 minutes and drain the water.
Input water quality usage limitations:
1. If the input water iron content is more than that prescribed in the technical specifications, use of an iron remover** is recommended as a pre-
treatment.
2. If the input water turbidity is more than that prescribed in the technical specifications or comprises colloidal particles, use of a special filter** is
required as a pre-filter.
3. If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer**
is recommended (applicable only for RO variants).
4. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications.
**Available at an extra cost.
PRE-REQUISITES FOR INSTALLATION
TDS modulator is located inside the product. As per factory setting, it comes in fully closed mode. TDS level of output water
can be increased by slowly loosening the spindle of the TDS modulator (anticlockwise). Normally a slight quarter turn is
enough to increase the TDS of the output water. Rotating the spindle in the clockwise direction closes the TDS modulator and
reduces the level of TDS blending.
Please note that the TDS blending, and its adjustment is dependent upon the level of TDS of input water and on the TDS
reduction capacity of the RO membrane. TDS adjustment should be done by the authorized Eureka Forbes technician only.
MTDS REGULATOR (Taste adjuster) OPERATING PROCEDURE
THE PROCESS OF PURIFICATION (For UV+UF Variant)
Stage Treatment Materials Benefits
1 Sediment Filter
Multi-layered Polypropylene spun cartridge
over the carbon block
Removes fine suspended particles such as dust, dirt mud and sand from water.
2 Chemi-BlockTM
Dust-free Bacteriostatic Activated Carbon
Block
Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odor from the
water.
3 Mineral Guard™
Micro Controller-based Electronic Impulse
Producer
Prevents the deposition of dissolved minerals like Ca and Mg on the Quartz Tube of UV
chamber, thus, enhancing the availability of minerals in water.
4 Ultra Filtration UF hollow fibre
Capillary tube type membrane-based technology that imparts crystal clear clarity to
drinking water, in addition to making the water safe from bacteriological contamination.
5 UV e-boilingTM Germicidal UV Lamp
UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and
protozoa, thereby, making it safe to drink.
6
Active CopperTM
with Zinc Booster
Cartridge*
A patented bacteriostatic taste enhancer with
double goodness of Active Copper™ and
Zinc Technology
Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory
properties that help to support healthy metabolism. It also helps to provide the body with
energy and is much needed for growth and development. Zinc also has a major role in the
immune system. The activated carbon removes organic components and polishes the
water, giving it a sparkling look, making it pure and great to taste.
*Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification
(Acceptable limit)
TECHNICAL SPECIFICATIONS*
# Parameter Specification
1 Model AG AURA UV+UF
PRODUCT SPECIFICATION
1 Dimension (W X D X H) 316 mm X 251 mm X 462 mm
2 Net Weight 5.3 KG (Approx.)
3 Purification Technology UV+UF
4 Tank Capacity 7 Litres (approx.)
5 Standard Purification supplied Combination Cartridge(sed. + Chemi-filter),
Mineral Guard™, UF Filter, UV e-boilingTM,
Active Copper™ with Zinc Booster
Cartridge,
ELECTRICAL SPECIFICATIONS
1 Power Rating 22 Watts
2 Power Supply Input 230V AC,50Hz
3 Operating Voltage Range 150 VAC to 280 VAC, 50 Hz
4 UV Lamp Life 8,000 burning hours (as per UV lamp manufacturer
spec.)
RECOMMENDED INPUT WATER PARAMETERS
1 Input Water Pressure Range** 0.3 to 2.0 kg/cm²
2 Iron Content (Max.) 0.1 mg/L
3 Chlorine Content (Max.) 0.2 mg/L
4 Input Water Turbidity (Max.) 5 NTU
5 Total Dissolved Solids (TDS)
(max.)
Up to 200 mg/L
*Technical Specifications are subject to change without prior notice.
Note: The performance data presented in the table is applicable under standard
laboratory conditions#. Actual performance may vary depending on the input water
quality, water pressure and condition of filters.
**If the pressure is higher than the maximum specified, use of a pressure reducing
valve is mandatory. If the pressure is lower than the minimum specified, use of a
Booster pump is recommended.
The above accessories are available with our company at an additional cost.
The purification cartridges are designed for a safe life of 1 year or 6000 liters# from the
date of installation whichever is earlier. Post the safe life, for your complete
protection, the machine shuts down the purification process.
Performance data sheets are available with Eureka Forbes Technical Documentation
Centre.
Warranty void if the product is not installed as per recommendations.
#Standard Test Conditions:
Feed Water Quality: TDS Max: 200 mg/litres with NaCl Pressure: 1.0 kg/cm2,
Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron:
below 0.1 mg/litres. Depending on the input water quality (variations in the standard
test conditions) the filter might need a replacement even before the purifier gives
you an alert.
#Actual performance may vary based on the input water conditions - TDS, Pressure,
Temperature & pH. Standard test Condition are valid for online water supply
installation.
Stage Treatment Materials Benefits
1 i-Filter™
Multi-layered Polypropylene Roving Wound
Cartridge Removes fine suspended particles such as dust, dirt mud and sand from water.
2 Chemi-Block™
Dust-free Bacteriostatic Activated Carbon
Block Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour from the
water.
3 Mineral Guard™
Micro Controller-based Electronic Impulse
Producer
Prevents the deposition of dissolved minerals like Ca and Mg on the Quartz Tube of UV
chamber, thus, enhancing the availability of minerals in water.
4
Membrane Life
Enhancer***
Special Anti-scalant Media
Prevents scaling of dissolved salts on the surface of the membrane, thereby, enhancing the
membrane life and performance.
5
Reverse Osmosis
Membrane
Thin Film Composite (TFC) Reverse Osmosis
Membrane
Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury.
Eliminates micro-organisms like bacteria, viruses, protozoa and cysts.
6 UV e-boilingTM Germicidal UV Lamp
UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and
protozoa, thereby, making it safe to drink.
7
Active CopperTM
with Zinc Booster
Cartridge*
A patented bacteriostatic taste enhancer with
double goodness of Active Copper™ and
Zinc Technology
Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory
properties that help to support healthy metabolism. It also helps to provide the body with
energy and is much needed for growth and development. Zinc also has a major role in the
immune system. The activated carbon removes organic components and polishes the
water, giving it a sparkling look, making it pure and great to taste.
*Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification
(Acceptable limit)
8 TDS Regulator Manual taste adjusting system Adjusts the TDS of purified water to provide healthy water always.
***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L).
Available at extra cost.
THE PROCESS OF PURIFICATION (For RO+UV+MTDS Variant)
TECHNICAL SPECIFICATIONS*
# Parameter Specification
1 Model AG AURA RO+UV+MTDS
PRODUCT SPECIFICATION
1 Dimension (W X D X H) 316 mm X 251 mm X 462 mm
2 Net Weight 6.6 kg (Approx.)
3 Purification Technology RO+UV+MTDS
4 Tank Capacity 7 Litres (approx.)
5 Standard Purification supplied i-Filter™, Chemi-BlockTM, Mineral
Guard™, Reverse Osmosis Cartridge,
UV e-boilingTM, Active Copper™ with
Zinc Booster Cartridge, TDS Regulator
ELECTRICAL SPECIFICATIONS
1 Power Rating 45 Watts
2 Power Supply Input 230V AC,50Hz
3 Operating Voltage Range 150 VAC to 280 VAC, 50 Hz
4 UV Lamp Life 5,000 burning hours (as per UV lamp
manufacturer spec.)
RECOMMENDED INPUT WATER PARAMETERS
1 Input Water Pressure Range** 0.3 to 3.0 kg/cm²
2 Iron Content (Max.) 0.1 mg/L
3 Chlorine Content (Max.) 0.2 mg/L
4 Input Water Turbidity (Max.) 5 NTU
5 Total Dissolved Solids (TDS) (max.) Up to 2,000 mg/L++
6 Total Hardness (max.) 600 mg/L
*Technical Specifications are subject to change without prior notice.
Note: The performance data presented in the table is applicable under standard
laboratory conditions#. Actual performance may vary depending on the input water
quality, water pressure and condition of filters.
**If the pressure is higher than the maximum specified, use of a pressure reducing valve
is mandatory.
++If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more
than 300 ppm (mg/L), use of a Membrane life enhancer is recommended.
The above accessories are available with our company at an additional cost.
The purification cartridges are designed for a safe life of 1 year or 6000 liters# from the
date of installation whichever is earlier. Post the safe life, for your complete
protection, the machine shuts down the purification process.
Performance data sheets are available with Eureka Forbes Technical Documentation
Centre.
Warranty void if the product is not installed as per recommendations.
#Standard Test Conditions:
Feed Water Quality: TDS Max: 750 mg/litres with NaCl Pressure: 1.0 kg/cm2,
Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron: below
0.1 mg/litres. Pressure on membrane: 75psi. Product Recovery @ 25%. Depending on
the input water quality (variations in the standard test conditions) the filter might need
a replacement even before the purifier gives you an alert.
#Actual performance may vary based on the input water conditions - TDS, Hardness,
Pressure, Temperature & pH. Standard test Condition are valid for online water supply
installation. In suction mode, the product performance may be lower than the claims.
Stage Treatment Materials Benefits
1 i-Filter™
Multi-layered Polypropylene Roving Wound
Cartridge
Removes fine suspended particles such as dust, dirt mud and sand from water.
2 Chemi-Block™ Dust-free Bacteriostatic Activated Carbon Block Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour from the water.
3 Mineral Guard™
Micro Controller-based Electronic Impulse
Producer
Prevents the deposition of dissolved minerals like Ca and Mg on the Quartz Tube of UV chamber,
thus, enhancing the availability of minerals in water.
4
Membrane Life
Enhancer***
Special Anti-scalant Media
Prevents scaling of dissolved salts on the surface of the membrane, thereby, enhancing the
membrane life and performance.
5
Reverse Osmosis
Membrane
Thin Film Composite (TFC) Reverse Osmosis
Membrane
Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury. Eliminates
micro-organisms like bacteria, viruses, protozoa and cysts.
6 UV e-boilingTM Germicidal UV Lamp
UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and protozoa,
thereby, making it safe to drink.
7 Ultra Filtration UF hollow fibre
Capillary tube type membrane-based technology that imparts crystal clear clarity to drinking
water, in addition to making the water safe from bacteriological contamination.
8
Active CopperTM
with Zinc Booster
Cartridge*
A patented bacteriostatic taste enhancer with
double goodness of Active Copper™ and Zinc
Technology
Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory properties
that help to support healthy metabolism. It also helps to provide the body with energy and is much
needed for growth and development. Zinc also has a major role in the immune system. The
activated carbon removes organic components and polishes the water, giving it a sparkling look,
making it pure and great to taste.
*Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification
(Acceptable limit)
9 TDS Regulator Manual taste adjusting system Adjusts the TDS of purified water to provide healthy water always.
***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L).
Available at extra cost.
THE PROCESS OF PURIFICATION (For RO+UV+UF+MTDS Variant)
TECHNICAL SPECIFICATIONS*
# Parameter Specification
1 Model AG AURA RO+UV+UF+MTDS
PRODUCT SPECIFICATION
1 Dimension (W X D X H) 316 mm X 251 mm X 462 mm
2 Net Weight 6.6 kg (Approx.)
3 Purification Technology RO+UV+UF+MTDS
4 Tank Capacity 7 Litres (approx.)
5 Standard Purification supplied i-Filter™, Chemi-BlockTM, Mineral
Guard™, Reverse Osmosis Cartridge,
UF Filter, UV e-boilingTM, Active
Copper™ with Zinc Booster
Cartridge, TDS Regulator
ELECTRICAL SPECIFICATIONS
1 Power Rating 45 Watts
2 Power Supply Input 230V AC,50Hz
3 Operating Voltage Range 150 VAC to 280 VAC, 50 Hz
4 UV Lamp Life 5,000 burning hours (as per UV lamp
manufacturer spec.)
RECOMMENDED INPUT WATER PARAMETERS
1 Input Water Pressure Range** 0.3 to 3.0 kg/cm²
2 Iron Content (Max.) 0.1 mg/L
3 Chlorine Content (Max.) 0.2 mg/L
4 Input Water Turbidity (Max.) 5 NTU
5 Total Dissolved Solids (TDS) (max.) Up to 2,000 mg/L++
6 Total Hardness (max.) 600 mg/L
*Technical Specifications are subject to change without prior notice.
Note: The performance data presented in the table is applicable under standard
laboratory conditions#. Actual performance may vary depending on the input water
quality, water pressure and condition of filters.
**If the pressure is higher than the maximum specified, use of a pressure reducing valve
is mandatory.
++If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more
than 300 ppm (mg/L), use of a Membrane life enhancer is recommended.
The above accessories are available with our company at an additional cost.
The purification cartridges are designed for a safe life of 1 year or 6000 liters# from the
date of installation whichever is earlier. Post the safe life, for your complete
protection, the machine shuts down the purification process.
Performance data sheets are available with Eureka Forbes Technical Documentation
Centre.
Warranty void if the product is not installed as per recommendations.
#Standard Test Conditions:
Feed Water Quality: TDS Max: 750 mg/litres with NaCl Pressure: 1.0 kg/cm2,
Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron: below
0.1 mg/litres. Pressure on membrane: 75psi. Product Recovery @ 25%. Depending on
the input water quality (variations in the standard test conditions) the filter might need
a replacement even before the purifier gives you an alert.
#Actual performance may vary based on the input water conditions - TDS, Hardness,
Pressure, Temperature & pH. Standard test Condition are valid for online water supply
installation. In suction mode, the product performance may be lower than the claims.
FUNCTION OF INDICATORS – LED DISPLAY
PARAMETERS LED INDICATION (1RGB) Remarks
Power ON
Red, Blue and Green blinks one after other for 1 sec, Green solid ON for 5
sec
Applicable for RO+UV. ,RO,UV models
Purification process Green Solid ON
Tank icon blinks for 6 seconds in RO+UV. and RO
models.Blinks for 30 seconds in case of UV models
Tank Filling Mode Blue Blinks @0.5sec Applicable for RO+UV. ,RO,UV models
Tank Full Mode Blue Solid ON Applicable for RO+UV. ,RO,UV models
UV Lamp Fault Red Solid ON Applicable only for RO+UV. and UV models
SV fault Red Blinks @0.5 sec Applicable for RO+UV. ,RO,UV models
Pump fault Red Blinks @0.5 sec Applicable only for RO+UV. and RO models
EA error Red Blinks @0.25 sec Applicable for RO+UV. ,RO,UV models
No water/Low water Purple Solid ON Applicable for RO+UV. ,RO,UV models
Pre Alert (30 days prior to EOL) white Blinks for 5 times for every 5 seconds interval
Applicable for RO+UV. ,RO,UV models
Alert (15 days prior to EOL) white Blinks for 5 times for every 2 seconds interval
EOL (At the end of the useful life of cartridges) white Blinks for 5 times for every 0.5 seconds interval
Pre Boot Blue Blinks @0.25sec Applicable for RO+UV. ,RO,UV models
Auto Safe not connected Red Blinks for 2 times for every 1 seconds interval Applicable for RO+UV. ,RO,UV models
Auto safe tampered fault Blue and Green blinks alternately at 0.5 seconds Applicable for RO+UV. ,RO,UV models
Filter Tampered Fault Green and Red blinks alternately @0.5 seconds Applicable for RO+UV. ,RO,UV models
Note: Storage tank of this product must be periodically (at least once in every 30 days) cleaned by a disinfectant.
Disinfection Tablets may be purchased from the company authorised Service Centre. Please follow the disinfection process
strictly as per the instructions as provided in this User Manual.
1. Drain the tank completely.
2. Switch OFF the water purifier from the main power supply.
3. Open the top cover, wipe the inside of the tank with a dry, clean soft cloth.
4. Keep the top cover in place.
5. Switch the power supply ON.
6. Let the storage tank gets filled and then drop one Disinfection Tablet* into the tank.
Caution: Keep the Disinfection Tablets out of the reach of children. Do not eat/consume the tablet.
7. Keep the top cover in place and leave the unit for 30 minutes.
8. After 30 minutes, open the tap and discard this and the first filling water completely. Caution: Do not drink this
water.
9. Now your unit is ready to use. In case you notice any medicinal taste/smell, discard the tank of water fully & let it refill
again.
10. Please ensure that this disinfection process is carried out by the authorised installation person/service technician during
first installation and in every subsequent mandatory servicing of the product.
*Available with Eureka Forbes Service Technician
CLEANING AND DISINFECTION OF WATER STORAGE TANK
• Read attentively and understand the purifier and its functions before use.
• Installation and service must be conducted by authorized person from Eureka Forbes Limited only.
• In case of any damage or incorrect functioning, immediately contact an authorized service center of Eureka Forbes
Limited.
• The flushed out water from the RO system is not suitable for drinking. You can use that water for gardening or to clean
floors (For applicable models only).
• Water storage tank must be periodically (at least once in every 30 days) cleaned using a disinfectant. (For applicable
models only).
• Drain the water from the tank if it hasn’t been used for over 48 hours. We recommend servicing by authorised person from
Eureka Forbes Limited, during prolonged non-usage of your water purifier. Beyond usable life of the filters, it is
recommended to replace with new ones.
• Ensure that the replacement of the consumable cartridges is done by a trained Eureka Forbes technician when end-of-life
filter change indication appears.
• Ensure that the filter cartridges and spares used during service/replacement, are genuine and from EFL only.
TIPS FOR SAFETY AND MAINTENANCE
RECYCLE & REUSE OF FLUSHED OUT WATER (applicable for RO variants only)
Water is a rapidly depleting resource. It is our moral responsibility to ensure that water is recycled as much as possible.
Flushed out water from a RO system is an unavoidable technology limitation. It maintains the performance of the purification process and
the service life of the membrane also. Eureka Forbes has taken utmost care to minimize the water wastage in our RO system without
compromising on the performance of the product.
The water flushed out by your Aquaguard® RO Water Purifier can be collected and used for several purposes.
Watering
plants
Daily household cleaning
tasks like mopping floors,
cleaning bathrooms,
kitchen sinks, etc.
Flushed Water can be used for :
Drinking Washing clothes
Flushed Water cannot be used for :
A QUICK CHECKLIST
Problems Checkpoints Solutions
Water tastes bad 1. Is the tank clean?
2. Have you kept the purified water in
the tank for too long?
3. Is it time to change the filter?
1. Clean the storage tank.
2. Dispose of water and clean the tank.
3. Call an authorised Eureka Forbes Service
Technician.
Less water has been purified 1. Is the tap water valve closed?
2. Is the tap water pressure too low?
3. Filters may be clogged or damaged
1. Open the tap water valve.
2. If so, the amount of purified water will be
reduced.
3. Call an authorised Eureka Forbes Service
Technician.
Water doesn’t flow into the
storage tank
1. Is there water available in the
overhead tank?
2. Is the main water supply tap closed?
3. Not sure what is wrong?
1. Ensure the overhead tank is filled with water.
2. Ensure the tap is open.
3. Call an authorised Eureka Forbes Service
Technician.
Water is leaking 1. Is water coming out of the top of the
purifier?
1. Close the tap water valve, unplug the power
cord, and call an authorised Eureka Forbes
Service Technician.
WARRANTY TERMS & CONDITIONS*
1. The Products are warranted against manufacturing defects for a period of twelve (12) months from the date of original purchase.
2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorized agent adequate opportunity to inspect test and remedy them for
which the Customer will deposit the goods at its own expense, if so, required by the Company with the Company's Office/Service Centre along with the original invoice in the city where
they are sold.
3. The Inspection and Test Report of the company's office/service centre will be final and binding under the warranty for determining defects, repairs / alterations required or carried out or
certifying work of the goods thereafter.
4. Aquaguard® may require initial setting, post-installation, depending on varying water conditions and power supply. In case of any service requirement, post-installation, please contact the
company's service centre.
5. The company or its authorized agent will be entitled to retain any defective part replaced under the warranty.
6. Notwithstanding anything to the contrary contained or implied by this warranty:
a) The company's liability under this warranty shall be limited to the first sale of the goods by the company to the customer and will not apply or extend to any secondary sale of goods by the
customer.
b) The company's liability under this warranty shall be limited only to defects in the goods which occur under the conditions of normal operation of the goods and their proper and prescribed use.
The warranty does not cover or extend to defects which are determined by the company or its authorized agents as occurring or resulting from or attributable to negligence, abuse, misuse,
faulty care, operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods on electrical supply for which they are not designed, or damage
caused by lightening or other electrical disturbances or interruptions, dismantling or re-installation at a different location.
c) The company's liability under this warranty shall remain valid only if the goods are duly installed by the company or its authorized agency at the location specified in the invoice and such
installation is undertaken by the company or its authorized agent or franchisee.
d) Consumable items mentioned in the consumables table are subject to normal wear and tear are not covered by this warranty. Please refer model specific components given in the user manual
under the table “consumable cartridges”.
e) Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the date of installation, on the condition that the input water is as per the standard
test conditions for RO variants (provided in the section “Technical specifications table”), mentioned in the user manual. If the RO membrane gets clogged within warranty period, it will be
cleaned/repaired/replaced free of charge as deemed fit by the company authorized service person/centre after inspection. (At applicable for RO models only.)
f) The customer will have no claim against the company, its employees and its authorized agents or franchisees under or pursuant to this warranty in respect of death or injury to the customer or
any other person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or operation or utilization of the goods otherwise than in accordance
with the user manual or by due to any other cause or circumstances beyond the control of the company.
WARRANTY TERMS & CONDITIONS*
g) The company's liability, under this warranty, shall in no event and under no circumstances exceed the price paid by the customer to the company for the goods stated in the invoice.
General
For the purpose of this warranty, the following expressions shall have the following meanings respectively:
1. The 'Goods' shall mean the goods described in the Order Form.
2. The 'Customer' shall mean the original purchaser of goods from the company.
3. The 'Company' shall mean EUREKA FORBES LIMITED.
4. Aquaguard means and includes Aquaguard® , Aquaguard® Select and Sure from Aquaguard®.
5. 'General Terms & Conditions' shall mean the terms and conditions agreed upon by the customer and the company printed on the Order Form.
6. 'Invoice' shall mean the invoice issued by the company to the customer describing the goods and indicating, inter alia, the total purchase price thereof and name of the customer.
7. 'User Manual shall mean the instructions for Installation, use and maintenance provided through QR code along with Product supplied by the company.
8. EFL reserves the right, in its absolute discretion, to change, alter or discontinue and alter the terms and conditions from time to time without any prior notice.
9. Any disputes are subject to Mumbai Jurisdiction only.
Post-warranty
1. The customer may be offered a yearly Service Contract at the prevailing company rates and terms.
2. In case the customer does not wish to enter the Service Contract, he has the option of calling the company's service centre having his Aquaguard® services on an actual basis, i.e., by paying
the labour cost and spares needed to attend to that service/complaint call at the prevailing company rates. Such service will be rendered by the company in towns/places where the company
has its service centres.
3. If during such servicing it is necessary for the company to replace or repair defective components or parts, the customer shall be required to pay for the same as per the company's prevailing
price list.
4. Eureka Forbes limited reserves the right to offer annual maintenance contract/ensure availability of spares only up to 7 years from the date of invoice.
*Conditions apply.
"Protection" has always been our motto and guiding principle. We care for the environment. We urge you to recycle the packaging material or
take it to the nearest recycling facility rather than dispose it off with the rest of your waste. Your product has been designed to work for many
years, however, should you wish to upgrade or replace your old product, remember to help protect the environment by disposing it off at your
local e-waste disposal center. Should you have any queries, the nearest authorized service center of Eureka Forbes will be able to guide you.
Allow us to become your environment partner; together we can make the world a cleaner place.
ENVIRONMENT PROTECTION:
HEALTH PROTECTTM
For your safety the specially designed and electronically authenticated purification cartridges of Aquaguard® ensure our promise of 'pure &
healthy water or no water' always. In the unlikely usage of a 'non-genuine' purification cartridge that could potentially deliver unsafe water - an
indication light will draw your attention. For your complete protection, it even shuts down the purification process. The purification cartridges
are designed for a safe life of 1 year or 6000 litres# from the date of installation, whichever is earlier. Post the safe life, for your complete
protection, the machine gives you an advance alert, post which it shuts down the purification process.
#Standard Test Conditions. Depending on the input water quality (variations in the standard test conditions) the filter might need a
replacement even before the purifier gives you an alert.
Water purifier GWPDAURUM40000.pdf
1 von 18

Recomendados

Más contenido relacionado

Similar a Water purifier GWPDAURUM40000.pdf

Pureit Classic NXT PIC RO Or RO+UV von
Pureit Classic NXT PIC RO Or RO+UVPureit Classic NXT PIC RO Or RO+UV
Pureit Classic NXT PIC RO Or RO+UVSEONeeraj
42 views8 Folien
Bio-Logic Ultraviolet Water Purifiers von
Bio-Logic Ultraviolet Water PurifiersBio-Logic Ultraviolet Water Purifiers
Bio-Logic Ultraviolet Water PurifiersKelleen Guyer
504 views8 Folien

Similar a Water purifier GWPDAURUM40000.pdf(20)

Pureit Classic NXT PIC RO Or RO+UV von SEONeeraj
Pureit Classic NXT PIC RO Or RO+UVPureit Classic NXT PIC RO Or RO+UV
Pureit Classic NXT PIC RO Or RO+UV
SEONeeraj42 views
Bio-Logic Ultraviolet Water Purifiers von Kelleen Guyer
Bio-Logic Ultraviolet Water PurifiersBio-Logic Ultraviolet Water Purifiers
Bio-Logic Ultraviolet Water Purifiers
Kelleen Guyer504 views
Livpure Envy Pro Plus RO Water Purifier von Wlson Mary
Livpure Envy Pro Plus RO Water PurifierLivpure Envy Pro Plus RO Water Purifier
Livpure Envy Pro Plus RO Water Purifier
Wlson Mary806 views
Livpure Envy Plus RO Water Purifier von Wlson Mary
Livpure Envy Plus RO Water PurifierLivpure Envy Plus RO Water Purifier
Livpure Envy Plus RO Water Purifier
Wlson Mary4.5K views
Livpure Envy Plus RO Water Purifier von Wlson Mary
Livpure Envy Plus RO Water PurifierLivpure Envy Plus RO Water Purifier
Livpure Envy Plus RO Water Purifier
Wlson Mary824 views
LIVPURE WATER PURIFIER BY WAAMIKA.pdf von SEONeeraj
LIVPURE WATER PURIFIER BY WAAMIKA.pdfLIVPURE WATER PURIFIER BY WAAMIKA.pdf
LIVPURE WATER PURIFIER BY WAAMIKA.pdf
SEONeeraj118 views
Pureit Classic Tutorials with Advanced Manual von Tajul Islam
Pureit Classic Tutorials with Advanced Manual Pureit Classic Tutorials with Advanced Manual
Pureit Classic Tutorials with Advanced Manual
Tajul Islam573 views
Pureit classic uv+ g2 - Waamika Enterprises Dehradun von SEONeeraj
Pureit classic uv+ g2 - Waamika Enterprises DehradunPureit classic uv+ g2 - Waamika Enterprises Dehradun
Pureit classic uv+ g2 - Waamika Enterprises Dehradun
SEONeeraj25 views
Aqua FIlter Water Purification and Water FIltration Product Dubai von Aqua Filter
Aqua FIlter Water Purification and Water FIltration Product DubaiAqua FIlter Water Purification and Water FIltration Product Dubai
Aqua FIlter Water Purification and Water FIltration Product Dubai
Aqua Filter874 views
Aqua FIlter Duabi UAE von Aqua Filter
Aqua FIlter Duabi UAEAqua FIlter Duabi UAE
Aqua FIlter Duabi UAE
Aqua Filter234 views
Pureit Classic G2 von SEONeeraj
Pureit Classic G2 Pureit Classic G2
Pureit Classic G2
SEONeeraj87 views
Pureit Classic G2 RO+MF von SEONeeraj
Pureit Classic G2 RO+MF Pureit Classic G2 RO+MF
Pureit Classic G2 RO+MF
SEONeeraj60 views
Pureit Copper Plus Eco Waamika Enterprises Dehradun von SEONeeraj
Pureit Copper Plus Eco Waamika Enterprises DehradunPureit Copper Plus Eco Waamika Enterprises Dehradun
Pureit Copper Plus Eco Waamika Enterprises Dehradun
SEONeeraj157 views

Water purifier GWPDAURUM40000.pdf

  • 2. Product installation should be done only by a trained Eureka Forbes Service Technician only. 1. Input water must be tested for Total Dissolved Solids (TDS) and Total Hardness - Install the product in a dry ventilated place. Keep it away from direct sunlight, heating devices or areas below 10oC. - The purifier should be placed in area which is free of ants/insects/other pests. - Ensure that the input tap water temperature is in the range of 10o - 40oC.Avoid installation to a hot water tap as it can damage the filters. 2. The input water pressure to your water purifier should be within the recommended range (refer variant specific technical specifications table). If the input water pressure is more than specified, installation of a PRV (Pressure Regulating Valve)** is mandatory. If the input water pressure is less than specified, installation of an external booster pump** is recommended. 3. Ensure that the filters are flushed thoroughly and independently for 3-5 minutes to remove fine particles present in the filter, before the installation of the unit. 4. After installation, run the purifier for 5-10 minutes and drain the water. Input water quality usage limitations: 1. If the input water iron content is more than that prescribed in the technical specifications, use of an iron remover** is recommended as a pre- treatment. 2. If the input water turbidity is more than that prescribed in the technical specifications or comprises colloidal particles, use of a special filter** is required as a pre-filter. 3. If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer** is recommended (applicable only for RO variants). 4. Do not install the water purifier if the TDS is more than that prescribed in the technical specifications. **Available at an extra cost. PRE-REQUISITES FOR INSTALLATION
  • 3. TDS modulator is located inside the product. As per factory setting, it comes in fully closed mode. TDS level of output water can be increased by slowly loosening the spindle of the TDS modulator (anticlockwise). Normally a slight quarter turn is enough to increase the TDS of the output water. Rotating the spindle in the clockwise direction closes the TDS modulator and reduces the level of TDS blending. Please note that the TDS blending, and its adjustment is dependent upon the level of TDS of input water and on the TDS reduction capacity of the RO membrane. TDS adjustment should be done by the authorized Eureka Forbes technician only. MTDS REGULATOR (Taste adjuster) OPERATING PROCEDURE
  • 4. THE PROCESS OF PURIFICATION (For UV+UF Variant) Stage Treatment Materials Benefits 1 Sediment Filter Multi-layered Polypropylene spun cartridge over the carbon block Removes fine suspended particles such as dust, dirt mud and sand from water. 2 Chemi-BlockTM Dust-free Bacteriostatic Activated Carbon Block Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odor from the water. 3 Mineral Guard™ Micro Controller-based Electronic Impulse Producer Prevents the deposition of dissolved minerals like Ca and Mg on the Quartz Tube of UV chamber, thus, enhancing the availability of minerals in water. 4 Ultra Filtration UF hollow fibre Capillary tube type membrane-based technology that imparts crystal clear clarity to drinking water, in addition to making the water safe from bacteriological contamination. 5 UV e-boilingTM Germicidal UV Lamp UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and protozoa, thereby, making it safe to drink. 6 Active CopperTM with Zinc Booster Cartridge* A patented bacteriostatic taste enhancer with double goodness of Active Copper™ and Zinc Technology Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory properties that help to support healthy metabolism. It also helps to provide the body with energy and is much needed for growth and development. Zinc also has a major role in the immune system. The activated carbon removes organic components and polishes the water, giving it a sparkling look, making it pure and great to taste. *Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification (Acceptable limit)
  • 5. TECHNICAL SPECIFICATIONS* # Parameter Specification 1 Model AG AURA UV+UF PRODUCT SPECIFICATION 1 Dimension (W X D X H) 316 mm X 251 mm X 462 mm 2 Net Weight 5.3 KG (Approx.) 3 Purification Technology UV+UF 4 Tank Capacity 7 Litres (approx.) 5 Standard Purification supplied Combination Cartridge(sed. + Chemi-filter), Mineral Guard™, UF Filter, UV e-boilingTM, Active Copper™ with Zinc Booster Cartridge, ELECTRICAL SPECIFICATIONS 1 Power Rating 22 Watts 2 Power Supply Input 230V AC,50Hz 3 Operating Voltage Range 150 VAC to 280 VAC, 50 Hz 4 UV Lamp Life 8,000 burning hours (as per UV lamp manufacturer spec.) RECOMMENDED INPUT WATER PARAMETERS 1 Input Water Pressure Range** 0.3 to 2.0 kg/cm² 2 Iron Content (Max.) 0.1 mg/L 3 Chlorine Content (Max.) 0.2 mg/L 4 Input Water Turbidity (Max.) 5 NTU 5 Total Dissolved Solids (TDS) (max.) Up to 200 mg/L *Technical Specifications are subject to change without prior notice. Note: The performance data presented in the table is applicable under standard laboratory conditions#. Actual performance may vary depending on the input water quality, water pressure and condition of filters. **If the pressure is higher than the maximum specified, use of a pressure reducing valve is mandatory. If the pressure is lower than the minimum specified, use of a Booster pump is recommended. The above accessories are available with our company at an additional cost. The purification cartridges are designed for a safe life of 1 year or 6000 liters# from the date of installation whichever is earlier. Post the safe life, for your complete protection, the machine shuts down the purification process. Performance data sheets are available with Eureka Forbes Technical Documentation Centre. Warranty void if the product is not installed as per recommendations. #Standard Test Conditions: Feed Water Quality: TDS Max: 200 mg/litres with NaCl Pressure: 1.0 kg/cm2, Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron: below 0.1 mg/litres. Depending on the input water quality (variations in the standard test conditions) the filter might need a replacement even before the purifier gives you an alert. #Actual performance may vary based on the input water conditions - TDS, Pressure, Temperature & pH. Standard test Condition are valid for online water supply installation.
  • 6. Stage Treatment Materials Benefits 1 i-Filter™ Multi-layered Polypropylene Roving Wound Cartridge Removes fine suspended particles such as dust, dirt mud and sand from water. 2 Chemi-Block™ Dust-free Bacteriostatic Activated Carbon Block Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour from the water. 3 Mineral Guard™ Micro Controller-based Electronic Impulse Producer Prevents the deposition of dissolved minerals like Ca and Mg on the Quartz Tube of UV chamber, thus, enhancing the availability of minerals in water. 4 Membrane Life Enhancer*** Special Anti-scalant Media Prevents scaling of dissolved salts on the surface of the membrane, thereby, enhancing the membrane life and performance. 5 Reverse Osmosis Membrane Thin Film Composite (TFC) Reverse Osmosis Membrane Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury. Eliminates micro-organisms like bacteria, viruses, protozoa and cysts. 6 UV e-boilingTM Germicidal UV Lamp UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and protozoa, thereby, making it safe to drink. 7 Active CopperTM with Zinc Booster Cartridge* A patented bacteriostatic taste enhancer with double goodness of Active Copper™ and Zinc Technology Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory properties that help to support healthy metabolism. It also helps to provide the body with energy and is much needed for growth and development. Zinc also has a major role in the immune system. The activated carbon removes organic components and polishes the water, giving it a sparkling look, making it pure and great to taste. *Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification (Acceptable limit) 8 TDS Regulator Manual taste adjusting system Adjusts the TDS of purified water to provide healthy water always. ***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost. THE PROCESS OF PURIFICATION (For RO+UV+MTDS Variant)
  • 7. TECHNICAL SPECIFICATIONS* # Parameter Specification 1 Model AG AURA RO+UV+MTDS PRODUCT SPECIFICATION 1 Dimension (W X D X H) 316 mm X 251 mm X 462 mm 2 Net Weight 6.6 kg (Approx.) 3 Purification Technology RO+UV+MTDS 4 Tank Capacity 7 Litres (approx.) 5 Standard Purification supplied i-Filter™, Chemi-BlockTM, Mineral Guard™, Reverse Osmosis Cartridge, UV e-boilingTM, Active Copper™ with Zinc Booster Cartridge, TDS Regulator ELECTRICAL SPECIFICATIONS 1 Power Rating 45 Watts 2 Power Supply Input 230V AC,50Hz 3 Operating Voltage Range 150 VAC to 280 VAC, 50 Hz 4 UV Lamp Life 5,000 burning hours (as per UV lamp manufacturer spec.) RECOMMENDED INPUT WATER PARAMETERS 1 Input Water Pressure Range** 0.3 to 3.0 kg/cm² 2 Iron Content (Max.) 0.1 mg/L 3 Chlorine Content (Max.) 0.2 mg/L 4 Input Water Turbidity (Max.) 5 NTU 5 Total Dissolved Solids (TDS) (max.) Up to 2,000 mg/L++ 6 Total Hardness (max.) 600 mg/L *Technical Specifications are subject to change without prior notice. Note: The performance data presented in the table is applicable under standard laboratory conditions#. Actual performance may vary depending on the input water quality, water pressure and condition of filters. **If the pressure is higher than the maximum specified, use of a pressure reducing valve is mandatory. ++If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer is recommended. The above accessories are available with our company at an additional cost. The purification cartridges are designed for a safe life of 1 year or 6000 liters# from the date of installation whichever is earlier. Post the safe life, for your complete protection, the machine shuts down the purification process. Performance data sheets are available with Eureka Forbes Technical Documentation Centre. Warranty void if the product is not installed as per recommendations. #Standard Test Conditions: Feed Water Quality: TDS Max: 750 mg/litres with NaCl Pressure: 1.0 kg/cm2, Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron: below 0.1 mg/litres. Pressure on membrane: 75psi. Product Recovery @ 25%. Depending on the input water quality (variations in the standard test conditions) the filter might need a replacement even before the purifier gives you an alert. #Actual performance may vary based on the input water conditions - TDS, Hardness, Pressure, Temperature & pH. Standard test Condition are valid for online water supply installation. In suction mode, the product performance may be lower than the claims.
  • 8. Stage Treatment Materials Benefits 1 i-Filter™ Multi-layered Polypropylene Roving Wound Cartridge Removes fine suspended particles such as dust, dirt mud and sand from water. 2 Chemi-Block™ Dust-free Bacteriostatic Activated Carbon Block Reduces excess chlorine and organic impurities. Also adsorbs bad taste and odour from the water. 3 Mineral Guard™ Micro Controller-based Electronic Impulse Producer Prevents the deposition of dissolved minerals like Ca and Mg on the Quartz Tube of UV chamber, thus, enhancing the availability of minerals in water. 4 Membrane Life Enhancer*** Special Anti-scalant Media Prevents scaling of dissolved salts on the surface of the membrane, thereby, enhancing the membrane life and performance. 5 Reverse Osmosis Membrane Thin Film Composite (TFC) Reverse Osmosis Membrane Reduces TDS, hardness, pesticides and heavy metals like arsenic, lead and mercury. Eliminates micro-organisms like bacteria, viruses, protozoa and cysts. 6 UV e-boilingTM Germicidal UV Lamp UV disinfects the water by eliminating waterborne disease-causing bacteria, viruses and protozoa, thereby, making it safe to drink. 7 Ultra Filtration UF hollow fibre Capillary tube type membrane-based technology that imparts crystal clear clarity to drinking water, in addition to making the water safe from bacteriological contamination. 8 Active CopperTM with Zinc Booster Cartridge* A patented bacteriostatic taste enhancer with double goodness of Active Copper™ and Zinc Technology Copper and Zinc are known to have antimicrobial, antioxidant, and anti-inflammatory properties that help to support healthy metabolism. It also helps to provide the body with energy and is much needed for growth and development. Zinc also has a major role in the immune system. The activated carbon removes organic components and polishes the water, giving it a sparkling look, making it pure and great to taste. *Copper and Zinc Infusion in adherence to IS 10500:2012 Drinking water specification (Acceptable limit) 9 TDS Regulator Manual taste adjusting system Adjusts the TDS of purified water to provide healthy water always. ***Not a part of the product, Membrane life enhancer is recommended if the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L). Available at extra cost. THE PROCESS OF PURIFICATION (For RO+UV+UF+MTDS Variant)
  • 9. TECHNICAL SPECIFICATIONS* # Parameter Specification 1 Model AG AURA RO+UV+UF+MTDS PRODUCT SPECIFICATION 1 Dimension (W X D X H) 316 mm X 251 mm X 462 mm 2 Net Weight 6.6 kg (Approx.) 3 Purification Technology RO+UV+UF+MTDS 4 Tank Capacity 7 Litres (approx.) 5 Standard Purification supplied i-Filter™, Chemi-BlockTM, Mineral Guard™, Reverse Osmosis Cartridge, UF Filter, UV e-boilingTM, Active Copper™ with Zinc Booster Cartridge, TDS Regulator ELECTRICAL SPECIFICATIONS 1 Power Rating 45 Watts 2 Power Supply Input 230V AC,50Hz 3 Operating Voltage Range 150 VAC to 280 VAC, 50 Hz 4 UV Lamp Life 5,000 burning hours (as per UV lamp manufacturer spec.) RECOMMENDED INPUT WATER PARAMETERS 1 Input Water Pressure Range** 0.3 to 3.0 kg/cm² 2 Iron Content (Max.) 0.1 mg/L 3 Chlorine Content (Max.) 0.2 mg/L 4 Input Water Turbidity (Max.) 5 NTU 5 Total Dissolved Solids (TDS) (max.) Up to 2,000 mg/L++ 6 Total Hardness (max.) 600 mg/L *Technical Specifications are subject to change without prior notice. Note: The performance data presented in the table is applicable under standard laboratory conditions#. Actual performance may vary depending on the input water quality, water pressure and condition of filters. **If the pressure is higher than the maximum specified, use of a pressure reducing valve is mandatory. ++If the input water TDS is more than 1,000 ppm (mg/L) or input water hardness is more than 300 ppm (mg/L), use of a Membrane life enhancer is recommended. The above accessories are available with our company at an additional cost. The purification cartridges are designed for a safe life of 1 year or 6000 liters# from the date of installation whichever is earlier. Post the safe life, for your complete protection, the machine shuts down the purification process. Performance data sheets are available with Eureka Forbes Technical Documentation Centre. Warranty void if the product is not installed as per recommendations. #Standard Test Conditions: Feed Water Quality: TDS Max: 750 mg/litres with NaCl Pressure: 1.0 kg/cm2, Turbidity: Max.1 NTU, Temperature: 25°C, Chlorine: below 0.2 mg/litres, Iron: below 0.1 mg/litres. Pressure on membrane: 75psi. Product Recovery @ 25%. Depending on the input water quality (variations in the standard test conditions) the filter might need a replacement even before the purifier gives you an alert. #Actual performance may vary based on the input water conditions - TDS, Hardness, Pressure, Temperature & pH. Standard test Condition are valid for online water supply installation. In suction mode, the product performance may be lower than the claims.
  • 10. FUNCTION OF INDICATORS – LED DISPLAY PARAMETERS LED INDICATION (1RGB) Remarks Power ON Red, Blue and Green blinks one after other for 1 sec, Green solid ON for 5 sec Applicable for RO+UV. ,RO,UV models Purification process Green Solid ON Tank icon blinks for 6 seconds in RO+UV. and RO models.Blinks for 30 seconds in case of UV models Tank Filling Mode Blue Blinks @0.5sec Applicable for RO+UV. ,RO,UV models Tank Full Mode Blue Solid ON Applicable for RO+UV. ,RO,UV models UV Lamp Fault Red Solid ON Applicable only for RO+UV. and UV models SV fault Red Blinks @0.5 sec Applicable for RO+UV. ,RO,UV models Pump fault Red Blinks @0.5 sec Applicable only for RO+UV. and RO models EA error Red Blinks @0.25 sec Applicable for RO+UV. ,RO,UV models No water/Low water Purple Solid ON Applicable for RO+UV. ,RO,UV models Pre Alert (30 days prior to EOL) white Blinks for 5 times for every 5 seconds interval Applicable for RO+UV. ,RO,UV models Alert (15 days prior to EOL) white Blinks for 5 times for every 2 seconds interval EOL (At the end of the useful life of cartridges) white Blinks for 5 times for every 0.5 seconds interval Pre Boot Blue Blinks @0.25sec Applicable for RO+UV. ,RO,UV models Auto Safe not connected Red Blinks for 2 times for every 1 seconds interval Applicable for RO+UV. ,RO,UV models Auto safe tampered fault Blue and Green blinks alternately at 0.5 seconds Applicable for RO+UV. ,RO,UV models Filter Tampered Fault Green and Red blinks alternately @0.5 seconds Applicable for RO+UV. ,RO,UV models
  • 11. Note: Storage tank of this product must be periodically (at least once in every 30 days) cleaned by a disinfectant. Disinfection Tablets may be purchased from the company authorised Service Centre. Please follow the disinfection process strictly as per the instructions as provided in this User Manual. 1. Drain the tank completely. 2. Switch OFF the water purifier from the main power supply. 3. Open the top cover, wipe the inside of the tank with a dry, clean soft cloth. 4. Keep the top cover in place. 5. Switch the power supply ON. 6. Let the storage tank gets filled and then drop one Disinfection Tablet* into the tank. Caution: Keep the Disinfection Tablets out of the reach of children. Do not eat/consume the tablet. 7. Keep the top cover in place and leave the unit for 30 minutes. 8. After 30 minutes, open the tap and discard this and the first filling water completely. Caution: Do not drink this water. 9. Now your unit is ready to use. In case you notice any medicinal taste/smell, discard the tank of water fully & let it refill again. 10. Please ensure that this disinfection process is carried out by the authorised installation person/service technician during first installation and in every subsequent mandatory servicing of the product. *Available with Eureka Forbes Service Technician CLEANING AND DISINFECTION OF WATER STORAGE TANK
  • 12. • Read attentively and understand the purifier and its functions before use. • Installation and service must be conducted by authorized person from Eureka Forbes Limited only. • In case of any damage or incorrect functioning, immediately contact an authorized service center of Eureka Forbes Limited. • The flushed out water from the RO system is not suitable for drinking. You can use that water for gardening or to clean floors (For applicable models only). • Water storage tank must be periodically (at least once in every 30 days) cleaned using a disinfectant. (For applicable models only). • Drain the water from the tank if it hasn’t been used for over 48 hours. We recommend servicing by authorised person from Eureka Forbes Limited, during prolonged non-usage of your water purifier. Beyond usable life of the filters, it is recommended to replace with new ones. • Ensure that the replacement of the consumable cartridges is done by a trained Eureka Forbes technician when end-of-life filter change indication appears. • Ensure that the filter cartridges and spares used during service/replacement, are genuine and from EFL only. TIPS FOR SAFETY AND MAINTENANCE
  • 13. RECYCLE & REUSE OF FLUSHED OUT WATER (applicable for RO variants only) Water is a rapidly depleting resource. It is our moral responsibility to ensure that water is recycled as much as possible. Flushed out water from a RO system is an unavoidable technology limitation. It maintains the performance of the purification process and the service life of the membrane also. Eureka Forbes has taken utmost care to minimize the water wastage in our RO system without compromising on the performance of the product. The water flushed out by your Aquaguard® RO Water Purifier can be collected and used for several purposes. Watering plants Daily household cleaning tasks like mopping floors, cleaning bathrooms, kitchen sinks, etc. Flushed Water can be used for : Drinking Washing clothes Flushed Water cannot be used for :
  • 14. A QUICK CHECKLIST Problems Checkpoints Solutions Water tastes bad 1. Is the tank clean? 2. Have you kept the purified water in the tank for too long? 3. Is it time to change the filter? 1. Clean the storage tank. 2. Dispose of water and clean the tank. 3. Call an authorised Eureka Forbes Service Technician. Less water has been purified 1. Is the tap water valve closed? 2. Is the tap water pressure too low? 3. Filters may be clogged or damaged 1. Open the tap water valve. 2. If so, the amount of purified water will be reduced. 3. Call an authorised Eureka Forbes Service Technician. Water doesn’t flow into the storage tank 1. Is there water available in the overhead tank? 2. Is the main water supply tap closed? 3. Not sure what is wrong? 1. Ensure the overhead tank is filled with water. 2. Ensure the tap is open. 3. Call an authorised Eureka Forbes Service Technician. Water is leaking 1. Is water coming out of the top of the purifier? 1. Close the tap water valve, unplug the power cord, and call an authorised Eureka Forbes Service Technician.
  • 15. WARRANTY TERMS & CONDITIONS* 1. The Products are warranted against manufacturing defects for a period of twelve (12) months from the date of original purchase. 2. The Customer will notify the Company in writing promptly of any defects noticed and give the Company or its authorized agent adequate opportunity to inspect test and remedy them for which the Customer will deposit the goods at its own expense, if so, required by the Company with the Company's Office/Service Centre along with the original invoice in the city where they are sold. 3. The Inspection and Test Report of the company's office/service centre will be final and binding under the warranty for determining defects, repairs / alterations required or carried out or certifying work of the goods thereafter. 4. Aquaguard® may require initial setting, post-installation, depending on varying water conditions and power supply. In case of any service requirement, post-installation, please contact the company's service centre. 5. The company or its authorized agent will be entitled to retain any defective part replaced under the warranty. 6. Notwithstanding anything to the contrary contained or implied by this warranty: a) The company's liability under this warranty shall be limited to the first sale of the goods by the company to the customer and will not apply or extend to any secondary sale of goods by the customer. b) The company's liability under this warranty shall be limited only to defects in the goods which occur under the conditions of normal operation of the goods and their proper and prescribed use. The warranty does not cover or extend to defects which are determined by the company or its authorized agents as occurring or resulting from or attributable to negligence, abuse, misuse, faulty care, operation or maintenance or repairs, alterations to the goods or any part thereof by others or the use of the goods on electrical supply for which they are not designed, or damage caused by lightening or other electrical disturbances or interruptions, dismantling or re-installation at a different location. c) The company's liability under this warranty shall remain valid only if the goods are duly installed by the company or its authorized agency at the location specified in the invoice and such installation is undertaken by the company or its authorized agent or franchisee. d) Consumable items mentioned in the consumables table are subject to normal wear and tear are not covered by this warranty. Please refer model specific components given in the user manual under the table “consumable cartridges”. e) Reverse Osmosis Membrane warranty is for a period of 1 year (or) 6,000 litres (whichever is earlier) from the date of installation, on the condition that the input water is as per the standard test conditions for RO variants (provided in the section “Technical specifications table”), mentioned in the user manual. If the RO membrane gets clogged within warranty period, it will be cleaned/repaired/replaced free of charge as deemed fit by the company authorized service person/centre after inspection. (At applicable for RO models only.) f) The customer will have no claim against the company, its employees and its authorized agents or franchisees under or pursuant to this warranty in respect of death or injury to the customer or any other person or loss or damage to any property caused by or due to equipment failure, breakdown or accident, fire or operation or utilization of the goods otherwise than in accordance with the user manual or by due to any other cause or circumstances beyond the control of the company.
  • 16. WARRANTY TERMS & CONDITIONS* g) The company's liability, under this warranty, shall in no event and under no circumstances exceed the price paid by the customer to the company for the goods stated in the invoice. General For the purpose of this warranty, the following expressions shall have the following meanings respectively: 1. The 'Goods' shall mean the goods described in the Order Form. 2. The 'Customer' shall mean the original purchaser of goods from the company. 3. The 'Company' shall mean EUREKA FORBES LIMITED. 4. Aquaguard means and includes Aquaguard® , Aquaguard® Select and Sure from Aquaguard®. 5. 'General Terms & Conditions' shall mean the terms and conditions agreed upon by the customer and the company printed on the Order Form. 6. 'Invoice' shall mean the invoice issued by the company to the customer describing the goods and indicating, inter alia, the total purchase price thereof and name of the customer. 7. 'User Manual shall mean the instructions for Installation, use and maintenance provided through QR code along with Product supplied by the company. 8. EFL reserves the right, in its absolute discretion, to change, alter or discontinue and alter the terms and conditions from time to time without any prior notice. 9. Any disputes are subject to Mumbai Jurisdiction only. Post-warranty 1. The customer may be offered a yearly Service Contract at the prevailing company rates and terms. 2. In case the customer does not wish to enter the Service Contract, he has the option of calling the company's service centre having his Aquaguard® services on an actual basis, i.e., by paying the labour cost and spares needed to attend to that service/complaint call at the prevailing company rates. Such service will be rendered by the company in towns/places where the company has its service centres. 3. If during such servicing it is necessary for the company to replace or repair defective components or parts, the customer shall be required to pay for the same as per the company's prevailing price list. 4. Eureka Forbes limited reserves the right to offer annual maintenance contract/ensure availability of spares only up to 7 years from the date of invoice. *Conditions apply.
  • 17. "Protection" has always been our motto and guiding principle. We care for the environment. We urge you to recycle the packaging material or take it to the nearest recycling facility rather than dispose it off with the rest of your waste. Your product has been designed to work for many years, however, should you wish to upgrade or replace your old product, remember to help protect the environment by disposing it off at your local e-waste disposal center. Should you have any queries, the nearest authorized service center of Eureka Forbes will be able to guide you. Allow us to become your environment partner; together we can make the world a cleaner place. ENVIRONMENT PROTECTION: HEALTH PROTECTTM For your safety the specially designed and electronically authenticated purification cartridges of Aquaguard® ensure our promise of 'pure & healthy water or no water' always. In the unlikely usage of a 'non-genuine' purification cartridge that could potentially deliver unsafe water - an indication light will draw your attention. For your complete protection, it even shuts down the purification process. The purification cartridges are designed for a safe life of 1 year or 6000 litres# from the date of installation, whichever is earlier. Post the safe life, for your complete protection, the machine gives you an advance alert, post which it shuts down the purification process. #Standard Test Conditions. Depending on the input water quality (variations in the standard test conditions) the filter might need a replacement even before the purifier gives you an alert.