SlideShare ist ein Scribd-Unternehmen logo
1 von 57
Downloaden Sie, um offline zu lesen
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
ACTION: Understand AC/DC Motors and Generators Theory
CONDITIONS: Given a laboratory environment, Labvolt trainers,
regulatory guidance, and applicable personal protective equipment.
STANDARD: Understand AC/DC Motors and Generators Theory In
order to aid the electrical design process.
UNCLASSIFIED
UNCLASSIFIED
• Safety Requirements: None
• Risk Assessment Level: Low
• Environmental Considerations: None
• Evaluation: Students will be evaluated on this
block of instruction during the Electrical Systems
and Design Examination 3. Students must
receive a score of 80 percent or above to receive
a GO.
UNCLASSIFIED
UNCLASSIFIED
LABVOLT Electric Power and Controls- AC/DC Motors and
Generators
UNCLASSIFIED
UNCLASSIFIED
• Fundamentals of Rotating Machines (1-3)
• DC Motors and Generators
• Separately excited DC Motor (2-1)
• Series, shunt, and compound DC motors (2-2)
• Special Characteristics of DC Motors
• The Universal Motor (3-2)
• AC Induction Motors
• Squirrel-cage motors (4-1)
• Single-phase Induction Motors (4-4)
S3D03-5
Lesson Objectives
UNCLASSIFIED
UNCLASSIFIED
Everyone should be familiar with some type of electric motor.
Typical examples include:
• Small DC motors in toys
• Fans
• Car starter motors
• Dryers
• Washers
• Well pumps
• HVAC fans/compressors
These common devices all operate using the same simple principal.
Motors use the reaction of two magnetic fields to create motion.
UNCLASSIFIED
UNCLASSIFIED
This is a simple image of how two magnets can interact and create
motion. If magnet A is turned, magnet B will follow, and vice-versa.
• The reaction of two
magnetic fields
• Attraction results in motion
UNCLASSIFIED
UNCLASSIFIED
Instead of just simply using 2 magnets, one magnet can be replaced
with a coil of wire wrapped around an iron core. The ends of the coil
are connected to a DC power source and results in current flowing
through the coil. This creates a north and south pole on the coil;
thus, creating an electromagnet.
https://www.youtube.com/watch?v=
mdZo_keUoEs
https://www.youtube.com/watch?v=
wzXRFp0DDrU
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
Electromagnets still require some initial motion to start the spinning.
One way to overcome this is to enable some type of directional
current switching.
• Current switching changes
polarity, and will simulate
rotating the magnet
• The operating principle of
all motors is based on
producing the electrical
equivalent to a rotating
magnet
• This avoids manual rotation
UNCLASSIFIED
UNCLASSIFIED
The direction of rotation can be reversed by interchanging currents
I1 and I2 as shown below.
UNCLASSIFIED
UNCLASSIFIED
The Generator Principle
• Based on Faraday’s Law
• Voltage is induced between terminals of a wire loop if the magnetic fluxl
inking the loop varies as a function of time
• The value of the induced voltage is proportional to the rate of change of
magnetic flux.
The induced voltage is given by the following equation
UNCLASSIFIED
UNCLASSIFIED
Example
𝑬 = 𝑵 ∗
Δω
Δ𝒕
𝑬 = 𝟏𝟎𝟎 ∗
𝟎. 𝟎𝟎𝟓 − 𝟎. 𝟎𝟎𝟑
𝟎. 𝟎𝟎𝟏
𝑬 = 𝟐𝟎𝟎𝑽
UNCLASSIFIED
UNCLASSIFIED
Work
A mechanical work is done whenever a force F moves through an
object over distance d, and work is defined by the following
equation:
Work is expressed in joules (J) when the force (F) is in Newtons (N)
and d is in meters (m).
𝑾 = 𝑭 ∗ 𝒅c
UNCLASSIFIED
UNCLASSIFIED
Torque
Now consider that the block is moved over the same distance using
a pulley that has a radius r.
A twisting force must be applied to turn the pully so that the rope
pulls the block with a force F.
The twisting force is known as torque, and defined by the following
equation:
The torque T is expressed in Newton-meters (N∙m) when the force F
and the radius r are expressed in Newtons (N) and in meters (m),
respectively.
T= 𝑭 ∗ 𝒓c
UNCLASSIFIED
UNCLASSIFIED
Torque
At the end of each complete rotation of the pulley, the block has
advanced a distance of 2(pi)r meters (inches), meaning that 2(pi)r*F
joules (pound force-inches) of work has been done. Since torque
equals F*r, the work may be expressed as 2(pi)T joules per
revolution.
T= 𝑭 ∗ 𝒓c
UNCLASSIFIED
UNCLASSIFIED
Power
Power is the rate of doing work, and given by the following equation:
P=
𝑾
𝒕
c
𝑷 𝒊𝒔 𝒕𝒉𝒆 𝒑𝒐𝒘𝒆𝒓 𝒊𝒏 𝒘𝒂𝒕𝒕𝒔 𝑾
W is the work in joules (J)
t is time taken to do the work, in seconds (S)
UNCLASSIFIED
UNCLASSIFIED
Power
Since power is work done per unit of time, the power of a motor
turning at speed n, can be found using the following equation when
torque is expressed in newton-meters
P= 𝟐 ∗ 𝒑𝒊 ∗ 𝑻 ∗ 𝒏 ∗
𝟏
𝟔𝟎
c
P=
𝒏∗𝒕
𝟗.𝟓𝟓
UNCLASSIFIED
UNCLASSIFIED
Motor power, losses, and efficiency
• Torque was earlier defined as a twisting force that causes an
object to rotate.
• In electric motors, this twisting force comes from the interaction
of magnetic fields, and its value is related to the current flowing in
the motor.
• Since the magnetic forces in the rotor of a dc motor are produced
by current flowing in a wire loop, increasing the current will
increase the strength of the magnetic forces.
• The motor will therefore produce more torque, meaning increased
motor power, and it will consume more electric power.
• The prime mover that you have been using is actually a dc motor
and it converts electrical power to mechanical power.
UNCLASSIFIED
UNCLASSIFIED
Motor power, losses, and efficiency
• Electric motor efficiency is expressed as the ratio of its
mechanical output power to its electrical input power, Pm/Pin.
• The mechanical output power of a motor depends on its speed
and torque, and can be determined using one of the following two
formulas, depending on whether torque is expressed in N∙m or
lbf∙in:
P 𝐦 =
𝒏∗𝒕
𝟗.𝟓𝟓
t in N*m P 𝐦 =
𝒏∗𝒕
𝟖𝟒.𝟓𝟏
𝒕 𝒊𝒏 𝒍𝒃𝒔 ∗ 𝒊𝒏
UNCLASSIFIED
UNCLASSIFIED
Motor power, losses, and efficiency
• Efficiency for a motor is usually shown in the form of a graph of
efficiency versus mechanical output power, although a specific
value at the nominal power rating is sometimes given.
• Rotating machine losses come from bearing friction, brush
friction, as well as windage and cooling-fan friction.
• These losses vary somewhat as speed increases from zero to its
nominal value, but remain fairly constant over the normal
operating range between no-load and full-load
UNCLASSIFIED
UNCLASSIFIED
Motor power, losses, and efficiency
UNCLASSIFIED
UNCLASSIFIED
Motor power, losses, and efficiency
• Electrical losses are classed as copper losses, brushes losses,
and iron losses.
• Copper losses (I*I*R) result from the resistance of the wire used in
the machine, are dissipated as heat, and depend on the value of
current in the machine.
• Brushes losses are usually very small, and are due to the contact
resistance of the brush which causes a typical voltage drop
between 0.8 V and 1.3 V.
• Finally, iron losses come from hysteresis and eddy currents in the
machine, and depend on the magnetic flux density, the speed of
rotation or frequency, the kind of steel and the size of the motor.
UNCLASSIFIED
UNCLASSIFIED
Check on Learning
Complete LSA 1 Quiz located
in Blackboard under the H33
Learning Module
UNCLASSIFIED
UNCLASSIFIED
• Motors turn due to an interaction between two magnetic fields
• The basic principle of a DC motor is the creation of a rotating magnet
inside of the mobile portion of the motor known as a ROTOR
• Commutator makes AC
needed for creation of
rotating magnet
• Contact to commutator
and external DC source
made through brushes
• Rotor of DC motor also
known as armature
UNCLASSIFIED
UNCLASSIFIED
• The brushes make contact with
segments A and B of the
commutator and current flows in
wire loop A-B. No current flows in
the other wire loop (C-D). This
creates an electromagnet A-B with
north and south.
• As the rotor continues to rotate
clockwise, a time comes where a
commutation occurs, i.e., the
brushes make contact with
segments C and D instead of
segments A and B. As a result,
current now flows in wire loop C-D
instead of flowing in wire loop A-B.
This creates an electromagnet C-
D with north and south poles.
UNCLASSIFIED
UNCLASSIFIED
• By comparing Figure 2-2b and
Figure 2-2c, you can see that the
magnetic north and south poles
rotate 90° counterclockwise at the
commutation.
• As the rotor continues to rotate
clockwise, the same phenomenon
repeats every 90° angle of
rotation, as shown in Figure 2-3a,
Figure 2-3b, and Figure 2-3c.
UNCLASSIFIED
UNCLASSIFIED
• As the rotor turns, north and south
poles of the electromagnet
oscillate 90 degrees
• N and S poles are stationary, and
do not turn as the rotor turns
• Equivalent to having
electromagnet in the rotor that
rotates as the same speed as the
rotor, but in an opposite direction
• If rotor is placed next to a fixed
permanent magnet stator, opposite
polarity poles attract each other
• Direction of rotation depends on
polarity of applied voltage to
brushes of motor
UNCLASSIFIED
UNCLASSIFIED
• Remember that a change in magnetic flux over a change in time can
induce a voltage on the ends of a coil wire……
• If a wire loop is placed between
two magnets and rotated,
magnetic lines of force are cut
and a voltage “e" is induced in
the loop.
• The polarity of the induced
voltage “e" depends on the
direction in which the wire loop
moves as it cuts the magnetic
lines of force.
• Since the wire loop cuts
magnetic lines of force in both
directions within a full
revolution, the induced voltage
is an ac voltage
UNCLASSIFIED
UNCLASSIFIED
• If a commutator such as that shown in Figure 2-1 is used, it will act as a
rectifier and convert the induced ac voltage into a dc voltage (with
ripple), as shown in Figure 2-6. Direct current will therefore be
produced at the output of the generator. The faster the rotor turns, the
more lines of force that are cut and the higher the output voltage. Also,
the stronger the stator magnet, the more lines of force that are present,
and therefore, the higher the output voltage.
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
UNCLASSIFIED
• Many DC motors use an electromagnet for the stator, such as seen in
the figure below. When the power for the stator electromagnet is
supplied from an external source, it is referred to as separately excited.
• The current flowing in the stator is often referred to as field current.
UNCLASSIFIED
UNCLASSIFIED
• Motor speed and armature voltage are a linear relationship.
• Induced voltage is proportional to motor speed.
• Because of this, DC motors are considered linear voltage-to-speed
converters.
UNCLASSIFIED
UNCLASSIFIED
• Also considered linear current-to-torque converter
• When armature current increases, the
voltage drop Era across the armature
resistor increases, and cannot be
neglected.
• At that point, armature voltage is equal to
the sum of induced voltage and Era.
UNCLASSIFIED
UNCLASSIFIED
Conduct lab 2-1.
UNCLASSIFIED
UNCLASSIFIED
Lab 2-1 Wrap-up
• The speed of the separately-excited dc motor is proportional to
armature voltage applied.
• The torque of a separately-excited dc motor is proportional to
armature current.
• The speed decreases with armature current increases if the
armature voltage is fixed.
• This is due to an increased voltage drop across the armature
resistor.
• Speed vs. voltage and current vs. torque relationships do not
change based off of reversed polarity.
• Also, the direction of rotation is reversed when polarity of
armature voltage is reversed.
• Complete 2-1 quiz on blackboard!!
UNCLASSIFIED
UNCLASSIFIED
• It is possible to change the characteristics of a separately-excited dc
motor by changing the strength of the fixed magnetic field produced by
the stator electromagnet. This can be carried out by changing the
current that flows in the stator electromagnet. This current is usually
referred to as the field current because it is used to produce the fixed
magnetic field in the dc motor.
• A rheostat connected in series with the electromagnet winding can be
used to vary the field current.
UNCLASSIFIED
UNCLASSIFIED
• Electromagnet is a series winding connected in series with armature.
• Speed decreases non-linearly as the torque increases
• Series motors provide strong starting torque
• Wide range of speeds
• Difficult to operate at constant speed as load fluctuates
• MUST NEVER run without load because of speed increase.
UNCLASSIFIED
UNCLASSIFIED
• Electromagnet is a shunt winding connected in parallel with armature.
• Difficult to change the speed by changing armature voltage
• Changes in field current oppose changes to speed
• Only requires a single fixed voltage
• Speed doesn’t vary as load shifts
UNCLASSIFIED
UNCLASSIFIED
• the characteristic of a cumulative
compound motor is a compromise of the
series and shunt motor characteristics.
• It provides the compound motor with a
fairly wide range of operating speed, but
the speed does not vary linearly as the
torque varies.
UNCLASSIFIED
UNCLASSIFIED
Conduct lab 2-2.
UNCLASSIFIED
UNCLASSIFIED
Lab 2-2 Wrap-up• Decreasing field current below its nominal value increases k1 but
decreases K2.
• Allows motor to operate at higher speeds without exceeding
nominal armature voltage.
• Reduces torque without exceeding armature current.
• It is possible to increase field current above rated value for short
periods of time to increase starting torque.
• The speed vs. torque characteristic of a series motor is such that
the speed of a series motor decreases more rapidly than a
separately excited motor as torque increases.
• Series motor- n vs. T in non-linear
• Separately-excited- n vs. T is linear
• Shunt- similar to separately-excited
• Compound- a compromise of both
• Complete 2-2 quiz on blackboard!!
UNCLASSIFIED
UNCLASSIFIED
• Remember that an Armature winding creates a rotating magnetic field
that rotates at the same speed as the motor but in the opposite
direction.
• The poles of the rotor electromagnet remain fixed at 90 degrees to the
stator electromagnet.
• If the polarity of the stator electromagnet or rotor is reversed, the
direction of rotation reverses. Remember Flemings Rule!
UNCLASSIFIED
UNCLASSIFIED
• When the field and armature electromagnet of a DC motor are powered
by the same source, like series and shunt motors, reversing polarity
reverses direction of currents .
• Shunt and series DC motors WILL rotate when connected to an AC
source because both armature and field currents flip-flop together, and
directional torque remains the same.
UNCLASSIFIED
UNCLASSIFIED
• Due to higher impedance in windings due to alternating current, a shunt
winding motor will not provide desired results.
• The shunt winding has a larger number of turns in the coil, and
produces higher impedances.
• Conversely, a series motor winding has very few windings and has a
lower impedance with AC.
• However, when a COMPENSATING winding is added to a series motor
winding, you can achieve greater results.
• These results can be seen using a universal motor with series and
compensating windings.
• Let’s watch some videos!!
UNCLASSIFIED
UNCLASSIFIED
Conduct lab 3-2.
UNCLASSIFIED
UNCLASSIFIED
Lab 3-2 Wrap-up
• DC series motors and universal motors without compensating
windings have similar operations with both AC and DC sources.
• The direction of rotation of these types depends on polarity of
armature and field currents.
• These specific types of motors operate poorly on AC sources
because of higher impedance.
• Universal motors operate much better when a compensating
winding is added to reduce overall impedance.
• Complete 3-2 quiz on blackboard!!
UNCLASSIFIED
UNCLASSIFIED
• Voltage is induced between 2 ends of a wire loop when magnetic flux
varies as a function of time.
• If the ends of the loop are shorted together, current flows in the closed
loop.
• As currents flow through the loops of the conductor ladder, they create
magnetic fields.
• When the magnetic fields interact, a force moves the closed ladder in
the direction of the moving magnet.
UNCLASSIFIED
UNCLASSIFIED
• Because of the pulling force of the magnetic field on the ladder, the
ladder must always move at a slower speed than the moving magnet.
• The greater the difference in speed, the larger variation of flux; thus,
greater magnetic force acting on the ladder.
• When the ladder of an asynchronous induction motor is closed like the
image below, it looks like a squirrel cage; thus, the name squirrel cage
motor.
• It sounded better than hamster wheel,
So smart folks just went with it.
UNCLASSIFIED
UNCLASSIFIED
• The stator of the squirrel-cage motor acts as a rotating electromagnet.
• If it is started with no load, it turns almost the same speed as the
rotating magnetic field (synchronous speed).
• Changing the phase sequence changes direction of rotation.
• Motor line currents increases as mechanical load increases.
• This means squirrel cage motors require more power for heavier
loads.
UNCLASSIFIED
UNCLASSIFIED
• No-load speed is just less than synchronous speed.
• As torque increases, speed decreases.
• Full load torque corresponds to full load speed.
• Too much torque creates instability (breakdown torque)
• When torque is zero (locked rotor torque), the current is very high and
the amount of power consumed is higher than normal operations.
• Squirrel-cage motors draw reactive power from the AC source.
• Under no-load conditions, reactive power is higher than active power.
UNCLASSIFIED
UNCLASSIFIED
• A Three phase squirrel cage induction motor starts and runs close to
normal if only using 2 phases.
• With only one phase connected, there is no rotating magnetic field to
pull the motor and start motion.
• In order to start a single phase induction motor, you must add an
auxiliary winding with a capacitor.
• The result is two currents that are 90 degrees out of phase from one
another, and allowed a rotating magnetic field to get it started.
• These motors typically use a centrifugal switch to isolate the auxiliary
windings once the motor is at a significant speed.
UNCLASSIFIED
UNCLASSIFIED
• In order to start a single phase induction motor, you must add an
auxiliary winding with a capacitor.
• The result is two currents that are 90 degrees out of phase from one
another, and allowed a rotating magnetic field to get it started.
UNCLASSIFIED
UNCLASSIFIED
Conduct lab 4-4.
UNCLASSIFIED
UNCLASSIFIED
Lab 4-4 Wrap-up
• A Three phase squirrel cage induction motor starts and runs close to
normal if only using 2 phases.
• With only one phase connected, there is no rotating magnetic field to
pull the motor and start motion.
• In order to start a single phase induction motor, you must add an
auxiliary winding with a capacitor.
• The result is two currents that are 90 degrees out of phase from one
another, and allowed a rotating magnetic field to get it started.
• These motors typically use a centrifugal switch to isolate the auxiliary
windings once the motor is at a significant speed.
• Complete 4-4 quiz on blackboard!!
UNCLASSIFIED
UNCLASSIFIED
• Fundamentals of Rotating Machines (1-3)
• DC Motors and Generators
• Separately excited DC Motor (2-1)
• Series, shunt, and compound DC motors (2-2)
• Special Characteristics of DC Motors
• The Universal Motor (3-2)
• AC Induction Motors
• Squirrel-cage motors (4-1)
• Single-phase Induction Motors (4-4)
S3D03-57
Summary

Más contenido relacionado

Was ist angesagt? (20)

DC GENERATOR
DC GENERATORDC GENERATOR
DC GENERATOR
 
Dc motors
Dc motorsDc motors
Dc motors
 
AC & DC Generators
AC & DC GeneratorsAC & DC Generators
AC & DC Generators
 
Dc machiness
Dc machinessDc machiness
Dc machiness
 
DC Generator
DC GeneratorDC Generator
DC Generator
 
Dc machine
Dc machineDc machine
Dc machine
 
DC compound motor ppt
DC compound motor pptDC compound motor ppt
DC compound motor ppt
 
Eece 259 dc generator
Eece 259 dc generatorEece 259 dc generator
Eece 259 dc generator
 
Generators [compatibility mode]
Generators [compatibility mode]Generators [compatibility mode]
Generators [compatibility mode]
 
Dc motor
Dc motorDc motor
Dc motor
 
Unit7 dc motors
Unit7 dc motorsUnit7 dc motors
Unit7 dc motors
 
Dc motor prasad 55
Dc motor prasad 55Dc motor prasad 55
Dc motor prasad 55
 
Ac electrical generators
Ac electrical generatorsAc electrical generators
Ac electrical generators
 
Dc machines
Dc machinesDc machines
Dc machines
 
D.c. machine
D.c. machineD.c. machine
D.c. machine
 
Dc machines
Dc machinesDc machines
Dc machines
 
ac generator
ac generatorac generator
ac generator
 
Ppt on DC Generator
Ppt on DC GeneratorPpt on DC Generator
Ppt on DC Generator
 
Working principle of dc motor
Working principle of dc motorWorking principle of dc motor
Working principle of dc motor
 
A.C GENERATOR
A.C GENERATORA.C GENERATOR
A.C GENERATOR
 

Ähnlich wie H33 ac dc motors and generators

Slides of DC Machines with detailed explanation
Slides of DC Machines with detailed explanationSlides of DC Machines with detailed explanation
Slides of DC Machines with detailed explanationOmer292805
 
actuation systems -up.pptx
actuation systems -up.pptxactuation systems -up.pptx
actuation systems -up.pptxJklMahanth
 
L6 Electrical Actuation system
L6 Electrical Actuation systemL6 Electrical Actuation system
L6 Electrical Actuation systemtaruian
 
SIMULATION OF DC SERIES MOTOR CHARACTERISTICS
SIMULATION OF DC SERIES MOTOR CHARACTERISTICS SIMULATION OF DC SERIES MOTOR CHARACTERISTICS
SIMULATION OF DC SERIES MOTOR CHARACTERISTICS sanjay kumar pediredla
 
actuation systems.pdf
actuation systems.pdfactuation systems.pdf
actuation systems.pdfJklMahanth
 
DC MOTORS-UNIT-II.pdf
DC MOTORS-UNIT-II.pdfDC MOTORS-UNIT-II.pdf
DC MOTORS-UNIT-II.pdfKUMARS641064
 
Permanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors pptPermanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors pptsrmrithi
 
CH 4 DC Machines.pptx
CH 4 DC Machines.pptxCH 4 DC Machines.pptx
CH 4 DC Machines.pptxmillion22
 
CH 4 DC Machines - Copy.pptx
CH 4 DC Machines - Copy.pptxCH 4 DC Machines - Copy.pptx
CH 4 DC Machines - Copy.pptxmillion22
 
Electric motors, generators and controls
Electric motors, generators and controlsElectric motors, generators and controls
Electric motors, generators and controlsCraig Kielb
 

Ähnlich wie H33 ac dc motors and generators (20)

Dc machines
Dc machinesDc machines
Dc machines
 
Slides of DC Machines with detailed explanation
Slides of DC Machines with detailed explanationSlides of DC Machines with detailed explanation
Slides of DC Machines with detailed explanation
 
actuation systems -up.pptx
actuation systems -up.pptxactuation systems -up.pptx
actuation systems -up.pptx
 
L6 Electrical Actuation system
L6 Electrical Actuation systemL6 Electrical Actuation system
L6 Electrical Actuation system
 
Electric motors
Electric motorsElectric motors
Electric motors
 
SIMULATION OF DC SERIES MOTOR CHARACTERISTICS
SIMULATION OF DC SERIES MOTOR CHARACTERISTICS SIMULATION OF DC SERIES MOTOR CHARACTERISTICS
SIMULATION OF DC SERIES MOTOR CHARACTERISTICS
 
actuation systems.pdf
actuation systems.pdfactuation systems.pdf
actuation systems.pdf
 
DC MOTORS-UNIT-II.pdf
DC MOTORS-UNIT-II.pdfDC MOTORS-UNIT-II.pdf
DC MOTORS-UNIT-II.pdf
 
Unit 1.pptx
Unit 1.pptxUnit 1.pptx
Unit 1.pptx
 
Permanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors pptPermanent magnet brushless dc motors ppt
Permanent magnet brushless dc motors ppt
 
Unit 5.pptx
Unit 5.pptxUnit 5.pptx
Unit 5.pptx
 
Alternator
AlternatorAlternator
Alternator
 
Drives.pptx
Drives.pptxDrives.pptx
Drives.pptx
 
CH 4 DC Machines.pptx
CH 4 DC Machines.pptxCH 4 DC Machines.pptx
CH 4 DC Machines.pptx
 
CH 4 DC Machines - Copy.pptx
CH 4 DC Machines - Copy.pptxCH 4 DC Machines - Copy.pptx
CH 4 DC Machines - Copy.pptx
 
BEEE machines
BEEE machinesBEEE machines
BEEE machines
 
Chapter 4 dc machine [autosaved]
Chapter 4   dc machine [autosaved]Chapter 4   dc machine [autosaved]
Chapter 4 dc machine [autosaved]
 
Electrical machines 2 AC Machines
Electrical machines 2 AC MachinesElectrical machines 2 AC Machines
Electrical machines 2 AC Machines
 
Chapter 2 latest
Chapter 2 latestChapter 2 latest
Chapter 2 latest
 
Electric motors, generators and controls
Electric motors, generators and controlsElectric motors, generators and controls
Electric motors, generators and controls
 

Mehr von phase3-120A

Power Circuits and Transforers-Unit 6 Labvolt Student Manual
Power Circuits and Transforers-Unit 6 Labvolt Student ManualPower Circuits and Transforers-Unit 6 Labvolt Student Manual
Power Circuits and Transforers-Unit 6 Labvolt Student Manualphase3-120A
 
Power Circuits and Transformers-Unit 4 Labvolt Student Manual
Power Circuits and Transformers-Unit 4 Labvolt Student ManualPower Circuits and Transformers-Unit 4 Labvolt Student Manual
Power Circuits and Transformers-Unit 4 Labvolt Student Manualphase3-120A
 
Power Circuits and Transformers-Unit 2 Labvolt Student Manual
Power Circuits and Transformers-Unit 2 Labvolt Student ManualPower Circuits and Transformers-Unit 2 Labvolt Student Manual
Power Circuits and Transformers-Unit 2 Labvolt Student Manualphase3-120A
 
Power Circuits and Transforers-Unit 9 Labvolt Student Manual
Power Circuits and Transforers-Unit 9 Labvolt Student ManualPower Circuits and Transforers-Unit 9 Labvolt Student Manual
Power Circuits and Transforers-Unit 9 Labvolt Student Manualphase3-120A
 
Power Circuits and Transforers-Unit 8 Labvolt Student Manual
Power Circuits and Transforers-Unit 8 Labvolt Student ManualPower Circuits and Transforers-Unit 8 Labvolt Student Manual
Power Circuits and Transforers-Unit 8 Labvolt Student Manualphase3-120A
 
Power Circuits and Transforers-Unit 7 Labvolt Student Manual
Power Circuits and Transforers-Unit 7 Labvolt Student ManualPower Circuits and Transforers-Unit 7 Labvolt Student Manual
Power Circuits and Transforers-Unit 7 Labvolt Student Manualphase3-120A
 
Power Circuits and Transforers-Unit 5 Labvolt Student Manual
Power Circuits and Transforers-Unit 5 Labvolt Student ManualPower Circuits and Transforers-Unit 5 Labvolt Student Manual
Power Circuits and Transforers-Unit 5 Labvolt Student Manualphase3-120A
 
Power Circuits and Transforers-Unit 1 Labvolt Student Manual
Power Circuits and Transforers-Unit 1 Labvolt Student ManualPower Circuits and Transforers-Unit 1 Labvolt Student Manual
Power Circuits and Transforers-Unit 1 Labvolt Student Manualphase3-120A
 
Power Circuits and Transforers-Unit 3 Labvolt Student Manual
Power Circuits and Transforers-Unit 3 Labvolt Student ManualPower Circuits and Transforers-Unit 3 Labvolt Student Manual
Power Circuits and Transforers-Unit 3 Labvolt Student Manualphase3-120A
 
H21 operational energy
H21 operational energyH21 operational energy
H21 operational energyphase3-120A
 
120A beb PE occupation plans
 120A beb PE occupation plans 120A beb PE occupation plans
120A beb PE occupation plansphase3-120A
 
H07 Power Load Survey
H07 Power Load SurveyH07 Power Load Survey
H07 Power Load Surveyphase3-120A
 
H09 Building Level Design
H09 Building Level DesignH09 Building Level Design
H09 Building Level Designphase3-120A
 
H08 Principles of Power Systems Design
H08 Principles of Power Systems Design H08 Principles of Power Systems Design
H08 Principles of Power Systems Design phase3-120A
 
Civil 3d surface import
Civil 3d surface importCivil 3d surface import
Civil 3d surface importphase3-120A
 
Career maps for da pam 600 3 update
Career maps for da pam 600 3 updateCareer maps for da pam 600 3 update
Career maps for da pam 600 3 updatephase3-120A
 
Fall 2018 engineer branch newsletter
Fall 2018 engineer branch newsletterFall 2018 engineer branch newsletter
Fall 2018 engineer branch newsletterphase3-120A
 
Act career maps (warrant officer) en-us-120 a
Act career maps (warrant officer) en-us-120 aAct career maps (warrant officer) en-us-120 a
Act career maps (warrant officer) en-us-120 aphase3-120A
 
120A- WOBC H05 Electrical safety day 3
120A- WOBC H05 Electrical safety day 3120A- WOBC H05 Electrical safety day 3
120A- WOBC H05 Electrical safety day 3phase3-120A
 
120A- WOBC H05 Electrical safety day 2
120A- WOBC H05 Electrical safety day 2120A- WOBC H05 Electrical safety day 2
120A- WOBC H05 Electrical safety day 2phase3-120A
 

Mehr von phase3-120A (20)

Power Circuits and Transforers-Unit 6 Labvolt Student Manual
Power Circuits and Transforers-Unit 6 Labvolt Student ManualPower Circuits and Transforers-Unit 6 Labvolt Student Manual
Power Circuits and Transforers-Unit 6 Labvolt Student Manual
 
Power Circuits and Transformers-Unit 4 Labvolt Student Manual
Power Circuits and Transformers-Unit 4 Labvolt Student ManualPower Circuits and Transformers-Unit 4 Labvolt Student Manual
Power Circuits and Transformers-Unit 4 Labvolt Student Manual
 
Power Circuits and Transformers-Unit 2 Labvolt Student Manual
Power Circuits and Transformers-Unit 2 Labvolt Student ManualPower Circuits and Transformers-Unit 2 Labvolt Student Manual
Power Circuits and Transformers-Unit 2 Labvolt Student Manual
 
Power Circuits and Transforers-Unit 9 Labvolt Student Manual
Power Circuits and Transforers-Unit 9 Labvolt Student ManualPower Circuits and Transforers-Unit 9 Labvolt Student Manual
Power Circuits and Transforers-Unit 9 Labvolt Student Manual
 
Power Circuits and Transforers-Unit 8 Labvolt Student Manual
Power Circuits and Transforers-Unit 8 Labvolt Student ManualPower Circuits and Transforers-Unit 8 Labvolt Student Manual
Power Circuits and Transforers-Unit 8 Labvolt Student Manual
 
Power Circuits and Transforers-Unit 7 Labvolt Student Manual
Power Circuits and Transforers-Unit 7 Labvolt Student ManualPower Circuits and Transforers-Unit 7 Labvolt Student Manual
Power Circuits and Transforers-Unit 7 Labvolt Student Manual
 
Power Circuits and Transforers-Unit 5 Labvolt Student Manual
Power Circuits and Transforers-Unit 5 Labvolt Student ManualPower Circuits and Transforers-Unit 5 Labvolt Student Manual
Power Circuits and Transforers-Unit 5 Labvolt Student Manual
 
Power Circuits and Transforers-Unit 1 Labvolt Student Manual
Power Circuits and Transforers-Unit 1 Labvolt Student ManualPower Circuits and Transforers-Unit 1 Labvolt Student Manual
Power Circuits and Transforers-Unit 1 Labvolt Student Manual
 
Power Circuits and Transforers-Unit 3 Labvolt Student Manual
Power Circuits and Transforers-Unit 3 Labvolt Student ManualPower Circuits and Transforers-Unit 3 Labvolt Student Manual
Power Circuits and Transforers-Unit 3 Labvolt Student Manual
 
H21 operational energy
H21 operational energyH21 operational energy
H21 operational energy
 
120A beb PE occupation plans
 120A beb PE occupation plans 120A beb PE occupation plans
120A beb PE occupation plans
 
H07 Power Load Survey
H07 Power Load SurveyH07 Power Load Survey
H07 Power Load Survey
 
H09 Building Level Design
H09 Building Level DesignH09 Building Level Design
H09 Building Level Design
 
H08 Principles of Power Systems Design
H08 Principles of Power Systems Design H08 Principles of Power Systems Design
H08 Principles of Power Systems Design
 
Civil 3d surface import
Civil 3d surface importCivil 3d surface import
Civil 3d surface import
 
Career maps for da pam 600 3 update
Career maps for da pam 600 3 updateCareer maps for da pam 600 3 update
Career maps for da pam 600 3 update
 
Fall 2018 engineer branch newsletter
Fall 2018 engineer branch newsletterFall 2018 engineer branch newsletter
Fall 2018 engineer branch newsletter
 
Act career maps (warrant officer) en-us-120 a
Act career maps (warrant officer) en-us-120 aAct career maps (warrant officer) en-us-120 a
Act career maps (warrant officer) en-us-120 a
 
120A- WOBC H05 Electrical safety day 3
120A- WOBC H05 Electrical safety day 3120A- WOBC H05 Electrical safety day 3
120A- WOBC H05 Electrical safety day 3
 
120A- WOBC H05 Electrical safety day 2
120A- WOBC H05 Electrical safety day 2120A- WOBC H05 Electrical safety day 2
120A- WOBC H05 Electrical safety day 2
 

Último

عناصر نباتية PDF.pdf architecture engineering
عناصر نباتية PDF.pdf architecture engineeringعناصر نباتية PDF.pdf architecture engineering
عناصر نباتية PDF.pdf architecture engineeringmennamohamed200y
 
Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...
Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...
Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...J. Agricultural Machinery
 
Final PPT.ppt about human detection and counting
Final PPT.ppt  about human detection and countingFinal PPT.ppt  about human detection and counting
Final PPT.ppt about human detection and countingArbazAhmad25
 
presentation by faizan[1] [Read-Only].pptx
presentation by faizan[1] [Read-Only].pptxpresentation by faizan[1] [Read-Only].pptx
presentation by faizan[1] [Read-Only].pptxkhfaizan534
 
Tekom Netherlands | The evolving landscape of Simplified Technical English b...
Tekom Netherlands | The evolving landscape of Simplified Technical English  b...Tekom Netherlands | The evolving landscape of Simplified Technical English  b...
Tekom Netherlands | The evolving landscape of Simplified Technical English b...Shumin Chen
 
12. Stairs by U Nyi Hla ngae from Myanmar.pdf
12. Stairs by U Nyi Hla ngae from Myanmar.pdf12. Stairs by U Nyi Hla ngae from Myanmar.pdf
12. Stairs by U Nyi Hla ngae from Myanmar.pdftpo482247
 
autonomous_vehicle_working_paper_01072020-_508_compliant.pdf
autonomous_vehicle_working_paper_01072020-_508_compliant.pdfautonomous_vehicle_working_paper_01072020-_508_compliant.pdf
autonomous_vehicle_working_paper_01072020-_508_compliant.pdfPandurangGurakhe
 
Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)
Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)
Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)Mizan Rahman
 
introduction to python, fundamentals and basics
introduction to python, fundamentals and basicsintroduction to python, fundamentals and basics
introduction to python, fundamentals and basicsKNaveenKumarECE
 
Flutter GDE session GDSC ZHCET AMU, aligarh
Flutter GDE session GDSC ZHCET AMU, aligarhFlutter GDE session GDSC ZHCET AMU, aligarh
Flutter GDE session GDSC ZHCET AMU, aligarhjamesbond00714
 
Introduction to Machine Learning Unit-2 Notes for II-II Mechanical Engineering
Introduction to Machine Learning Unit-2 Notes for II-II Mechanical EngineeringIntroduction to Machine Learning Unit-2 Notes for II-II Mechanical Engineering
Introduction to Machine Learning Unit-2 Notes for II-II Mechanical EngineeringC Sai Kiran
 
zomato data mining datasets for quality prefernece and conntrol.pptx
zomato data mining  datasets for quality prefernece and conntrol.pptxzomato data mining  datasets for quality prefernece and conntrol.pptx
zomato data mining datasets for quality prefernece and conntrol.pptxPratikMhatre39
 
Conventional vs Modern method (Philosophies) of Tunneling-re.pptx
Conventional vs Modern method (Philosophies) of Tunneling-re.pptxConventional vs Modern method (Philosophies) of Tunneling-re.pptx
Conventional vs Modern method (Philosophies) of Tunneling-re.pptxSAQIB KHURSHEED WANI
 
Research paper publications: Meaning of Q1 Q2 Q3 Q4 Journal
Research paper publications: Meaning of Q1 Q2 Q3 Q4 JournalResearch paper publications: Meaning of Q1 Q2 Q3 Q4 Journal
Research paper publications: Meaning of Q1 Q2 Q3 Q4 JournalDr. Manjunatha. P
 
A brief about Jeypore Sub-station Presentation
A brief about Jeypore Sub-station PresentationA brief about Jeypore Sub-station Presentation
A brief about Jeypore Sub-station PresentationJeyporess2021
 
Chapter 2 Canal Falls at Mnnit Allahabad .pptx
Chapter 2 Canal Falls at Mnnit Allahabad .pptxChapter 2 Canal Falls at Mnnit Allahabad .pptx
Chapter 2 Canal Falls at Mnnit Allahabad .pptxButcher771
 
The Art of Cloud Native Defense on Kubernetes
The Art of Cloud Native Defense on KubernetesThe Art of Cloud Native Defense on Kubernetes
The Art of Cloud Native Defense on KubernetesJacopo Nardiello
 
Road to GDSC (Become the next GDSC lead)
Road to GDSC (Become the next GDSC lead)Road to GDSC (Become the next GDSC lead)
Road to GDSC (Become the next GDSC lead)GDSCNiT
 

Último (20)

عناصر نباتية PDF.pdf architecture engineering
عناصر نباتية PDF.pdf architecture engineeringعناصر نباتية PDF.pdf architecture engineering
عناصر نباتية PDF.pdf architecture engineering
 
Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...
Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...
Investigating the Efficiency of Drinking Water Treatment Sludge and Iron-Base...
 
Final PPT.ppt about human detection and counting
Final PPT.ppt  about human detection and countingFinal PPT.ppt  about human detection and counting
Final PPT.ppt about human detection and counting
 
presentation by faizan[1] [Read-Only].pptx
presentation by faizan[1] [Read-Only].pptxpresentation by faizan[1] [Read-Only].pptx
presentation by faizan[1] [Read-Only].pptx
 
Tekom Netherlands | The evolving landscape of Simplified Technical English b...
Tekom Netherlands | The evolving landscape of Simplified Technical English  b...Tekom Netherlands | The evolving landscape of Simplified Technical English  b...
Tekom Netherlands | The evolving landscape of Simplified Technical English b...
 
12. Stairs by U Nyi Hla ngae from Myanmar.pdf
12. Stairs by U Nyi Hla ngae from Myanmar.pdf12. Stairs by U Nyi Hla ngae from Myanmar.pdf
12. Stairs by U Nyi Hla ngae from Myanmar.pdf
 
autonomous_vehicle_working_paper_01072020-_508_compliant.pdf
autonomous_vehicle_working_paper_01072020-_508_compliant.pdfautonomous_vehicle_working_paper_01072020-_508_compliant.pdf
autonomous_vehicle_working_paper_01072020-_508_compliant.pdf
 
Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)
Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)
Fabrics Finishing Manual ( Arkey Knit Dyeing Mills Ltd)
 
introduction to python, fundamentals and basics
introduction to python, fundamentals and basicsintroduction to python, fundamentals and basics
introduction to python, fundamentals and basics
 
Flutter GDE session GDSC ZHCET AMU, aligarh
Flutter GDE session GDSC ZHCET AMU, aligarhFlutter GDE session GDSC ZHCET AMU, aligarh
Flutter GDE session GDSC ZHCET AMU, aligarh
 
Introduction to Machine Learning Unit-2 Notes for II-II Mechanical Engineering
Introduction to Machine Learning Unit-2 Notes for II-II Mechanical EngineeringIntroduction to Machine Learning Unit-2 Notes for II-II Mechanical Engineering
Introduction to Machine Learning Unit-2 Notes for II-II Mechanical Engineering
 
zomato data mining datasets for quality prefernece and conntrol.pptx
zomato data mining  datasets for quality prefernece and conntrol.pptxzomato data mining  datasets for quality prefernece and conntrol.pptx
zomato data mining datasets for quality prefernece and conntrol.pptx
 
Conventional vs Modern method (Philosophies) of Tunneling-re.pptx
Conventional vs Modern method (Philosophies) of Tunneling-re.pptxConventional vs Modern method (Philosophies) of Tunneling-re.pptx
Conventional vs Modern method (Philosophies) of Tunneling-re.pptx
 
Research paper publications: Meaning of Q1 Q2 Q3 Q4 Journal
Research paper publications: Meaning of Q1 Q2 Q3 Q4 JournalResearch paper publications: Meaning of Q1 Q2 Q3 Q4 Journal
Research paper publications: Meaning of Q1 Q2 Q3 Q4 Journal
 
A brief about Jeypore Sub-station Presentation
A brief about Jeypore Sub-station PresentationA brief about Jeypore Sub-station Presentation
A brief about Jeypore Sub-station Presentation
 
Chapter 2 Canal Falls at Mnnit Allahabad .pptx
Chapter 2 Canal Falls at Mnnit Allahabad .pptxChapter 2 Canal Falls at Mnnit Allahabad .pptx
Chapter 2 Canal Falls at Mnnit Allahabad .pptx
 
The Art of Cloud Native Defense on Kubernetes
The Art of Cloud Native Defense on KubernetesThe Art of Cloud Native Defense on Kubernetes
The Art of Cloud Native Defense on Kubernetes
 
Hydraulic Loading System - Neometrix Defence
Hydraulic Loading System - Neometrix DefenceHydraulic Loading System - Neometrix Defence
Hydraulic Loading System - Neometrix Defence
 
Road to GDSC (Become the next GDSC lead)
Road to GDSC (Become the next GDSC lead)Road to GDSC (Become the next GDSC lead)
Road to GDSC (Become the next GDSC lead)
 
Caltrans view on recycling of in-place asphalt pavements
Caltrans view on recycling of in-place asphalt pavementsCaltrans view on recycling of in-place asphalt pavements
Caltrans view on recycling of in-place asphalt pavements
 

H33 ac dc motors and generators

  • 2. UNCLASSIFIED UNCLASSIFIED ACTION: Understand AC/DC Motors and Generators Theory CONDITIONS: Given a laboratory environment, Labvolt trainers, regulatory guidance, and applicable personal protective equipment. STANDARD: Understand AC/DC Motors and Generators Theory In order to aid the electrical design process.
  • 3. UNCLASSIFIED UNCLASSIFIED • Safety Requirements: None • Risk Assessment Level: Low • Environmental Considerations: None • Evaluation: Students will be evaluated on this block of instruction during the Electrical Systems and Design Examination 3. Students must receive a score of 80 percent or above to receive a GO.
  • 4. UNCLASSIFIED UNCLASSIFIED LABVOLT Electric Power and Controls- AC/DC Motors and Generators
  • 5. UNCLASSIFIED UNCLASSIFIED • Fundamentals of Rotating Machines (1-3) • DC Motors and Generators • Separately excited DC Motor (2-1) • Series, shunt, and compound DC motors (2-2) • Special Characteristics of DC Motors • The Universal Motor (3-2) • AC Induction Motors • Squirrel-cage motors (4-1) • Single-phase Induction Motors (4-4) S3D03-5 Lesson Objectives
  • 6. UNCLASSIFIED UNCLASSIFIED Everyone should be familiar with some type of electric motor. Typical examples include: • Small DC motors in toys • Fans • Car starter motors • Dryers • Washers • Well pumps • HVAC fans/compressors These common devices all operate using the same simple principal. Motors use the reaction of two magnetic fields to create motion.
  • 7. UNCLASSIFIED UNCLASSIFIED This is a simple image of how two magnets can interact and create motion. If magnet A is turned, magnet B will follow, and vice-versa. • The reaction of two magnetic fields • Attraction results in motion
  • 8. UNCLASSIFIED UNCLASSIFIED Instead of just simply using 2 magnets, one magnet can be replaced with a coil of wire wrapped around an iron core. The ends of the coil are connected to a DC power source and results in current flowing through the coil. This creates a north and south pole on the coil; thus, creating an electromagnet. https://www.youtube.com/watch?v= mdZo_keUoEs https://www.youtube.com/watch?v= wzXRFp0DDrU
  • 11. UNCLASSIFIED UNCLASSIFIED Electromagnets still require some initial motion to start the spinning. One way to overcome this is to enable some type of directional current switching. • Current switching changes polarity, and will simulate rotating the magnet • The operating principle of all motors is based on producing the electrical equivalent to a rotating magnet • This avoids manual rotation
  • 12. UNCLASSIFIED UNCLASSIFIED The direction of rotation can be reversed by interchanging currents I1 and I2 as shown below.
  • 13. UNCLASSIFIED UNCLASSIFIED The Generator Principle • Based on Faraday’s Law • Voltage is induced between terminals of a wire loop if the magnetic fluxl inking the loop varies as a function of time • The value of the induced voltage is proportional to the rate of change of magnetic flux. The induced voltage is given by the following equation
  • 14. UNCLASSIFIED UNCLASSIFIED Example 𝑬 = 𝑵 ∗ Δω Δ𝒕 𝑬 = 𝟏𝟎𝟎 ∗ 𝟎. 𝟎𝟎𝟓 − 𝟎. 𝟎𝟎𝟑 𝟎. 𝟎𝟎𝟏 𝑬 = 𝟐𝟎𝟎𝑽
  • 15. UNCLASSIFIED UNCLASSIFIED Work A mechanical work is done whenever a force F moves through an object over distance d, and work is defined by the following equation: Work is expressed in joules (J) when the force (F) is in Newtons (N) and d is in meters (m). 𝑾 = 𝑭 ∗ 𝒅c
  • 16. UNCLASSIFIED UNCLASSIFIED Torque Now consider that the block is moved over the same distance using a pulley that has a radius r. A twisting force must be applied to turn the pully so that the rope pulls the block with a force F. The twisting force is known as torque, and defined by the following equation: The torque T is expressed in Newton-meters (N∙m) when the force F and the radius r are expressed in Newtons (N) and in meters (m), respectively. T= 𝑭 ∗ 𝒓c
  • 17. UNCLASSIFIED UNCLASSIFIED Torque At the end of each complete rotation of the pulley, the block has advanced a distance of 2(pi)r meters (inches), meaning that 2(pi)r*F joules (pound force-inches) of work has been done. Since torque equals F*r, the work may be expressed as 2(pi)T joules per revolution. T= 𝑭 ∗ 𝒓c
  • 18. UNCLASSIFIED UNCLASSIFIED Power Power is the rate of doing work, and given by the following equation: P= 𝑾 𝒕 c 𝑷 𝒊𝒔 𝒕𝒉𝒆 𝒑𝒐𝒘𝒆𝒓 𝒊𝒏 𝒘𝒂𝒕𝒕𝒔 𝑾 W is the work in joules (J) t is time taken to do the work, in seconds (S)
  • 19. UNCLASSIFIED UNCLASSIFIED Power Since power is work done per unit of time, the power of a motor turning at speed n, can be found using the following equation when torque is expressed in newton-meters P= 𝟐 ∗ 𝒑𝒊 ∗ 𝑻 ∗ 𝒏 ∗ 𝟏 𝟔𝟎 c P= 𝒏∗𝒕 𝟗.𝟓𝟓
  • 20. UNCLASSIFIED UNCLASSIFIED Motor power, losses, and efficiency • Torque was earlier defined as a twisting force that causes an object to rotate. • In electric motors, this twisting force comes from the interaction of magnetic fields, and its value is related to the current flowing in the motor. • Since the magnetic forces in the rotor of a dc motor are produced by current flowing in a wire loop, increasing the current will increase the strength of the magnetic forces. • The motor will therefore produce more torque, meaning increased motor power, and it will consume more electric power. • The prime mover that you have been using is actually a dc motor and it converts electrical power to mechanical power.
  • 21. UNCLASSIFIED UNCLASSIFIED Motor power, losses, and efficiency • Electric motor efficiency is expressed as the ratio of its mechanical output power to its electrical input power, Pm/Pin. • The mechanical output power of a motor depends on its speed and torque, and can be determined using one of the following two formulas, depending on whether torque is expressed in N∙m or lbf∙in: P 𝐦 = 𝒏∗𝒕 𝟗.𝟓𝟓 t in N*m P 𝐦 = 𝒏∗𝒕 𝟖𝟒.𝟓𝟏 𝒕 𝒊𝒏 𝒍𝒃𝒔 ∗ 𝒊𝒏
  • 22. UNCLASSIFIED UNCLASSIFIED Motor power, losses, and efficiency • Efficiency for a motor is usually shown in the form of a graph of efficiency versus mechanical output power, although a specific value at the nominal power rating is sometimes given. • Rotating machine losses come from bearing friction, brush friction, as well as windage and cooling-fan friction. • These losses vary somewhat as speed increases from zero to its nominal value, but remain fairly constant over the normal operating range between no-load and full-load
  • 24. UNCLASSIFIED UNCLASSIFIED Motor power, losses, and efficiency • Electrical losses are classed as copper losses, brushes losses, and iron losses. • Copper losses (I*I*R) result from the resistance of the wire used in the machine, are dissipated as heat, and depend on the value of current in the machine. • Brushes losses are usually very small, and are due to the contact resistance of the brush which causes a typical voltage drop between 0.8 V and 1.3 V. • Finally, iron losses come from hysteresis and eddy currents in the machine, and depend on the magnetic flux density, the speed of rotation or frequency, the kind of steel and the size of the motor.
  • 25. UNCLASSIFIED UNCLASSIFIED Check on Learning Complete LSA 1 Quiz located in Blackboard under the H33 Learning Module
  • 26. UNCLASSIFIED UNCLASSIFIED • Motors turn due to an interaction between two magnetic fields • The basic principle of a DC motor is the creation of a rotating magnet inside of the mobile portion of the motor known as a ROTOR • Commutator makes AC needed for creation of rotating magnet • Contact to commutator and external DC source made through brushes • Rotor of DC motor also known as armature
  • 27. UNCLASSIFIED UNCLASSIFIED • The brushes make contact with segments A and B of the commutator and current flows in wire loop A-B. No current flows in the other wire loop (C-D). This creates an electromagnet A-B with north and south. • As the rotor continues to rotate clockwise, a time comes where a commutation occurs, i.e., the brushes make contact with segments C and D instead of segments A and B. As a result, current now flows in wire loop C-D instead of flowing in wire loop A-B. This creates an electromagnet C- D with north and south poles.
  • 28. UNCLASSIFIED UNCLASSIFIED • By comparing Figure 2-2b and Figure 2-2c, you can see that the magnetic north and south poles rotate 90° counterclockwise at the commutation. • As the rotor continues to rotate clockwise, the same phenomenon repeats every 90° angle of rotation, as shown in Figure 2-3a, Figure 2-3b, and Figure 2-3c.
  • 29. UNCLASSIFIED UNCLASSIFIED • As the rotor turns, north and south poles of the electromagnet oscillate 90 degrees • N and S poles are stationary, and do not turn as the rotor turns • Equivalent to having electromagnet in the rotor that rotates as the same speed as the rotor, but in an opposite direction • If rotor is placed next to a fixed permanent magnet stator, opposite polarity poles attract each other • Direction of rotation depends on polarity of applied voltage to brushes of motor
  • 30. UNCLASSIFIED UNCLASSIFIED • Remember that a change in magnetic flux over a change in time can induce a voltage on the ends of a coil wire…… • If a wire loop is placed between two magnets and rotated, magnetic lines of force are cut and a voltage “e" is induced in the loop. • The polarity of the induced voltage “e" depends on the direction in which the wire loop moves as it cuts the magnetic lines of force. • Since the wire loop cuts magnetic lines of force in both directions within a full revolution, the induced voltage is an ac voltage
  • 31. UNCLASSIFIED UNCLASSIFIED • If a commutator such as that shown in Figure 2-1 is used, it will act as a rectifier and convert the induced ac voltage into a dc voltage (with ripple), as shown in Figure 2-6. Direct current will therefore be produced at the output of the generator. The faster the rotor turns, the more lines of force that are cut and the higher the output voltage. Also, the stronger the stator magnet, the more lines of force that are present, and therefore, the higher the output voltage.
  • 33. UNCLASSIFIED UNCLASSIFIED • Many DC motors use an electromagnet for the stator, such as seen in the figure below. When the power for the stator electromagnet is supplied from an external source, it is referred to as separately excited. • The current flowing in the stator is often referred to as field current.
  • 34. UNCLASSIFIED UNCLASSIFIED • Motor speed and armature voltage are a linear relationship. • Induced voltage is proportional to motor speed. • Because of this, DC motors are considered linear voltage-to-speed converters.
  • 35. UNCLASSIFIED UNCLASSIFIED • Also considered linear current-to-torque converter • When armature current increases, the voltage drop Era across the armature resistor increases, and cannot be neglected. • At that point, armature voltage is equal to the sum of induced voltage and Era.
  • 37. UNCLASSIFIED UNCLASSIFIED Lab 2-1 Wrap-up • The speed of the separately-excited dc motor is proportional to armature voltage applied. • The torque of a separately-excited dc motor is proportional to armature current. • The speed decreases with armature current increases if the armature voltage is fixed. • This is due to an increased voltage drop across the armature resistor. • Speed vs. voltage and current vs. torque relationships do not change based off of reversed polarity. • Also, the direction of rotation is reversed when polarity of armature voltage is reversed. • Complete 2-1 quiz on blackboard!!
  • 38. UNCLASSIFIED UNCLASSIFIED • It is possible to change the characteristics of a separately-excited dc motor by changing the strength of the fixed magnetic field produced by the stator electromagnet. This can be carried out by changing the current that flows in the stator electromagnet. This current is usually referred to as the field current because it is used to produce the fixed magnetic field in the dc motor. • A rheostat connected in series with the electromagnet winding can be used to vary the field current.
  • 39. UNCLASSIFIED UNCLASSIFIED • Electromagnet is a series winding connected in series with armature. • Speed decreases non-linearly as the torque increases • Series motors provide strong starting torque • Wide range of speeds • Difficult to operate at constant speed as load fluctuates • MUST NEVER run without load because of speed increase.
  • 40. UNCLASSIFIED UNCLASSIFIED • Electromagnet is a shunt winding connected in parallel with armature. • Difficult to change the speed by changing armature voltage • Changes in field current oppose changes to speed • Only requires a single fixed voltage • Speed doesn’t vary as load shifts
  • 41. UNCLASSIFIED UNCLASSIFIED • the characteristic of a cumulative compound motor is a compromise of the series and shunt motor characteristics. • It provides the compound motor with a fairly wide range of operating speed, but the speed does not vary linearly as the torque varies.
  • 43. UNCLASSIFIED UNCLASSIFIED Lab 2-2 Wrap-up• Decreasing field current below its nominal value increases k1 but decreases K2. • Allows motor to operate at higher speeds without exceeding nominal armature voltage. • Reduces torque without exceeding armature current. • It is possible to increase field current above rated value for short periods of time to increase starting torque. • The speed vs. torque characteristic of a series motor is such that the speed of a series motor decreases more rapidly than a separately excited motor as torque increases. • Series motor- n vs. T in non-linear • Separately-excited- n vs. T is linear • Shunt- similar to separately-excited • Compound- a compromise of both • Complete 2-2 quiz on blackboard!!
  • 44. UNCLASSIFIED UNCLASSIFIED • Remember that an Armature winding creates a rotating magnetic field that rotates at the same speed as the motor but in the opposite direction. • The poles of the rotor electromagnet remain fixed at 90 degrees to the stator electromagnet. • If the polarity of the stator electromagnet or rotor is reversed, the direction of rotation reverses. Remember Flemings Rule!
  • 45. UNCLASSIFIED UNCLASSIFIED • When the field and armature electromagnet of a DC motor are powered by the same source, like series and shunt motors, reversing polarity reverses direction of currents . • Shunt and series DC motors WILL rotate when connected to an AC source because both armature and field currents flip-flop together, and directional torque remains the same.
  • 46. UNCLASSIFIED UNCLASSIFIED • Due to higher impedance in windings due to alternating current, a shunt winding motor will not provide desired results. • The shunt winding has a larger number of turns in the coil, and produces higher impedances. • Conversely, a series motor winding has very few windings and has a lower impedance with AC. • However, when a COMPENSATING winding is added to a series motor winding, you can achieve greater results. • These results can be seen using a universal motor with series and compensating windings. • Let’s watch some videos!!
  • 48. UNCLASSIFIED UNCLASSIFIED Lab 3-2 Wrap-up • DC series motors and universal motors without compensating windings have similar operations with both AC and DC sources. • The direction of rotation of these types depends on polarity of armature and field currents. • These specific types of motors operate poorly on AC sources because of higher impedance. • Universal motors operate much better when a compensating winding is added to reduce overall impedance. • Complete 3-2 quiz on blackboard!!
  • 49. UNCLASSIFIED UNCLASSIFIED • Voltage is induced between 2 ends of a wire loop when magnetic flux varies as a function of time. • If the ends of the loop are shorted together, current flows in the closed loop. • As currents flow through the loops of the conductor ladder, they create magnetic fields. • When the magnetic fields interact, a force moves the closed ladder in the direction of the moving magnet.
  • 50. UNCLASSIFIED UNCLASSIFIED • Because of the pulling force of the magnetic field on the ladder, the ladder must always move at a slower speed than the moving magnet. • The greater the difference in speed, the larger variation of flux; thus, greater magnetic force acting on the ladder. • When the ladder of an asynchronous induction motor is closed like the image below, it looks like a squirrel cage; thus, the name squirrel cage motor. • It sounded better than hamster wheel, So smart folks just went with it.
  • 51. UNCLASSIFIED UNCLASSIFIED • The stator of the squirrel-cage motor acts as a rotating electromagnet. • If it is started with no load, it turns almost the same speed as the rotating magnetic field (synchronous speed). • Changing the phase sequence changes direction of rotation. • Motor line currents increases as mechanical load increases. • This means squirrel cage motors require more power for heavier loads.
  • 52. UNCLASSIFIED UNCLASSIFIED • No-load speed is just less than synchronous speed. • As torque increases, speed decreases. • Full load torque corresponds to full load speed. • Too much torque creates instability (breakdown torque) • When torque is zero (locked rotor torque), the current is very high and the amount of power consumed is higher than normal operations. • Squirrel-cage motors draw reactive power from the AC source. • Under no-load conditions, reactive power is higher than active power.
  • 53. UNCLASSIFIED UNCLASSIFIED • A Three phase squirrel cage induction motor starts and runs close to normal if only using 2 phases. • With only one phase connected, there is no rotating magnetic field to pull the motor and start motion. • In order to start a single phase induction motor, you must add an auxiliary winding with a capacitor. • The result is two currents that are 90 degrees out of phase from one another, and allowed a rotating magnetic field to get it started. • These motors typically use a centrifugal switch to isolate the auxiliary windings once the motor is at a significant speed.
  • 54. UNCLASSIFIED UNCLASSIFIED • In order to start a single phase induction motor, you must add an auxiliary winding with a capacitor. • The result is two currents that are 90 degrees out of phase from one another, and allowed a rotating magnetic field to get it started.
  • 56. UNCLASSIFIED UNCLASSIFIED Lab 4-4 Wrap-up • A Three phase squirrel cage induction motor starts and runs close to normal if only using 2 phases. • With only one phase connected, there is no rotating magnetic field to pull the motor and start motion. • In order to start a single phase induction motor, you must add an auxiliary winding with a capacitor. • The result is two currents that are 90 degrees out of phase from one another, and allowed a rotating magnetic field to get it started. • These motors typically use a centrifugal switch to isolate the auxiliary windings once the motor is at a significant speed. • Complete 4-4 quiz on blackboard!!
  • 57. UNCLASSIFIED UNCLASSIFIED • Fundamentals of Rotating Machines (1-3) • DC Motors and Generators • Separately excited DC Motor (2-1) • Series, shunt, and compound DC motors (2-2) • Special Characteristics of DC Motors • The Universal Motor (3-2) • AC Induction Motors • Squirrel-cage motors (4-1) • Single-phase Induction Motors (4-4) S3D03-57 Summary

Hinweis der Redaktion

  1. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  2. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  3. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  4. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  5. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  6. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  7. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  8. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  9. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  10. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  11. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  12. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  13. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  14. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  15. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  16. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  17. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  18. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  19. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  20. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU
  21. https://www.youtube.com/watch?v=mdZo_keUoEs https://www.youtube.com/watch?v=wzXRFp0DDrU