Tata Steel is one of the largest steel producers in the world, established in 1907 in Jamshedpur, India. Numerical control (NC) and computer numerical control (CNC) allow machines to be controlled by programmed sets of instructions, enabling precise and repeatable machining of complex geometries. A CNC system consists of a part program, program input device, machine control unit, drive system, machine tool, and feedback system working together to automate production. CNC machines offer advantages like increased accuracy and reduced human errors compared to manual machining.
2. INTRODUCTION
Established in 1907 by J.N.Tata.
Formerly known as TATA IRON AND STEEL
COMPANY LIMITED(TISCO)
World’s 6th Largest Steel making company.
28.1 million p.a. of crude steel production
capacity.
Products: Steel, Blast furnaces,EOT cranes,
Automobiles, Machines etc.
Headquartered in Jamshedpur, Jharkhand and
registered office in Mumbai ,India
220/08/2011
3. INTRODUCTION OF NC AND CNC
NC stands for Numerical Control
CNC is self contained NC system with a
dedicated computer.
Control a machine by programs or set of
instructions.
Widely used for manufacturing system like
Machine Tools, Welders, And Laser Beam
Cutters
320/08/2011
4. Motivation and Uses
420/08/2011
To manufacture complex curved geometries
in 2D or 3D was extremely expensive by
mechanical
Machining components with repeatable
accuracy
Unmanned machining operations
5. 520/08/2011
ADVANTAGES DISADVANTAGES
Easier to program
Easy storage of existing
programs
Easy to change a program
Avoids human errors
NC machines are safer to operate
Complex geometry is produced
as cheaply as simple ones
Usually generates closer
tolerances than manual machines
Increase in electrical
maintenance.
Increase in initial investment.
Training of existing workforce.
Not cost-effective for low-level
production on simple parts
6. CNC SYSTEM ELEMENTS
620/08/2011
A typical CNC system consists of the
following six elements
Part program
Program input device
Machine control unit
Drive system
Machine tool
Feedback system
9. PART PROGRAM
920/08/2011
A part program is a series of coded
instructions required to produce a part as
in the following example
N10 G01 X5.0 Y2.5 F15.0
| | | | |
| | | | Feed rate (15 in/min)
| | | Y-coordinate (2.5")
| | X-coordinate (5.0")
| Linear interpolation mode
Sequence number
10. BLOCK
1020/08/2011
Block is the smallest part of the programme.
The block is composed of words and always
ends with the characters “END OF BLOCK”.
A block contains the following WORDS :
Sequence / Block number __________________________ N
Preparatory Functions _____________________________ G
Dimensions _____________________________________ X, Y, Z
Arc Center Offset _________________________________ I, J, K
Feed Function ___________________________________ F
Speed Function __________________________________ S
Tool Function ____________________________________ T
Miscellaneous Function ____________________________ M
11. PROGRAM INPUT DEVICE
1120/08/2011
The program input device is the
mechanism for part programs to be
entered into the CNC control.
The most commonly used program input
devices are keyboards, punched tape
reader, throgh RS 232 serial ports and
networks.
12. MACHINE CONTROL UNIT
1220/08/2011
It is used to perform the following
functions:
Read coded instructions
Decode coded instructions
Implement interpolations (linear, circular,
and helical) to generate axis motion
commands
Feed axis motion commands to the amplifier
circuits for driving the axis mechanisms
Receive the feedback signals of position and
speed for each drive axis
Implement auxiliary control functions such
as coolant or spindle on/off, and tool change
13. TYPES OF CNC CONTROL
SYSTEMS
1320/08/2011
Open-loop control
Closed-loop control
DRIVE SYSTEM
A drive system consists of :
amplifier circuits,
stepping motors or servomotors
ball lead-screws
17. 1720/08/2011
3. Limit Switches
Interlocks a mechanical motion or
position with an electrical circuit.
Most common limit switch is the
single-pole contact block with
one NO and one NC set of
contacts
18. 4. PUSH BUTTONS
1820/08/2011
Simple switch
mechanism for
controlling a process.
Colour coded: red(stop)
green (start)
19. 5. CONTACTOR
1920/08/2011
Used for switching a power
circuit of higher ampere
ratings.
Electromagnet provides
driving force to close the
contact.
Enclosed in insulating
material for protection.
20. Conclusion
2020/08/2011
• Learned about the basic electrical
components.
• Learn different circuits used in CNC
machine.
• Introduction to CNC machine.
• Basic programming of CNC machine.