1. Evap-Tech MTC Inc. présente:
Le IAQ-Tek et le VT8000
de Tek-Air
Les solutions pour mesurer l'apport d'air frais !
2. Objectifs de la présentation
• Pourquoi mesurer l’apport d’air extérieur
• Connaître les défis et contraintes pour mesurer l’apport
d’air extérieur dans les bâtiments
• Connaître les technologies disponibles (avantages et
limitations
• Déterminer les paramètres d’opération
• Déterminer les critères d’installation
2
3. Mesurer l’apport d’air extérieur
• Comment définir l'application?
• Quantifier le volume d'air introduit dans le bâtiment par les unités
de ventilation ou autre apport d’air
• S'assurer que la quantité d'air est suffisante pour rencontrer les
exigences du standard ASHRAE 62-2010
• La préoccupation?
• Maintenir une qualité d'air intérieur acceptable
• Éviter les maladies reliées au bâtiments et les responsabilités
associées
3
4. Les défis de l'application
• Vitesses faibles, typiquement, 100 à 700 PPM
• Des écart de température importants, (-40
jusqu'à 120 degrés F)
• Influencent la précision ainsi que l'opération des
composantes électroniques
• Influence le volume indiqué causé par les
changements de densité
• Taux d'humidité élevé car il peut pleuvoir
• La saleté et la poussière car l'air n'est pas filtré
• Doit pouvoir opérer pendant plusieurs années
avec un minimum d'entretien!
4
5. Le gros défi, la localisation de la
sonde
• Positionner la sonde
• Il n'y a jamais suffisamment de longueur droite de conduit pour
avoir une lecture sans turbulence
• Les persiennes et volets modulants peuvent causer encore plus
de turbulence ce qui génère des lectures instables et non fiables.
• Le vent qui souffle sur la face des persiennes et induit des
fluctuations importantes de la quantité d'air admise. Cela cause
une variation du signal aux volets et rend le système de contrôle
instable!
5
6. Le défi; la localisation de la sonde
6
RETOUR
PRISE
D`AIR
EXTÉRIEUR MÉLANGE
PERSIENNES
VOLETS
ZONE DE MESURE
7. 23 septembre 2015 7
Il nous fera plaisir de vous présenter la version
complète sur demande.
Veuillez nous contacter au 418-651-7111 ou
par courriel: info@evap-techmtc.com
Notes de l'éditeur
Good morning/afternoon. Today I am going to introduce you to a new product from Tek-Air called the IAQ-Tek, or Q-Tek for short.
In the next half hour I will show you why Q-Tek should become your first choice for outdoor air intake volume measurement.
I know many of you are already familiar with ASHRAE standard 62-89 for proper building ventilation which specifies the amount of outdoor air (OA) that should be brought into a building.
This standard also suggests that the volume of outdoor air be verified. Many engineers have interpreted the intent of this statement as requiring that the outdoor air volume be measured.
Right now this standard is being revised and is out for review. The proposed revision is more specific and requires that outdoor air be measured.
I know many of you are already familiar with ASHRAE standard 62-89 for proper building ventilation which specifies the amount of outdoor air (OA) that should be brought into a building.
This standard also suggests that the volume of outdoor air be verified. Many engineers have interpreted the intent of this statement as requiring that the outdoor air volume be measured.
Right now this standard is being revised and is out for review. The proposed revision is more specific and requires that outdoor air be measured.
Outdoor air volume is one of the most challenging measurements you as a design engineer must specify.
Conditions in the outdoor air are not at all like those found in the rest of the ventilation system.
Let’s look at some of the specific challenges.
Speaker should touch on each of the bullet points-
While all of these conditions make the measurement more difficult, it is locating the sensor which is the biggest problem a designer has to deal with.
Specifically-
Speaker to touch on each of the bullet items
Let’s look at a typical application at the intake of an air handler.
Air is drawn in the intake louvers, then within a few feet of exiting the louver, is drawn into the outdoor air dampers.
After the dampers, the outdoor air is mixed with return air and is no longer measurable as only outdoor air.
The IDEAL MEASUREMENT ZONE is the area in between the louvers and the outdoor air intake damper.
This is where most of the flow sensors available today perform the worst.
Q: Should we repeat some of these questions in relevant places in the PPT after we’ve talked about the subject to test learner’s knowledge? This slide could be shown at the end and reviewed.
Q: Are there other questions you want us to use in the PPT?
Q: Where do you want the "Assessment Questions” to be interspersed in the PPT? In the presenter notes? On new slides at the end of each section?