2. Notes:
If you see any mistake on my PowerPoint
slides or if you have any questions about the
materials, please feel free to email me at
vivek.it@live.com
Thanks
Vivek Kumar
TechnicalTrainer
3. Objectives
Encounter and describe the limitations of
RIPv1’s limitations.
Apply the basic Routing Information Protocol
Version 2 (RIPv2) configuration commands
and evaluate RIPv2 classless routing updates.
Analyze router output to see RIPv2 support for
VLSM and CIDR
Identify RIPv2 verification commands and
common RIPv2 issues.
Configure, verify, and troubleshoot RIPv2 in
“hands-on” labs
4. Introduction
Difference between RIPv1 & RIPv2
RIPv1
• A classful distance vector routing protocol
• Does not support discontiguous subnets
• Does not supportVLSM
• Does not send subnet mask in routing update
• Routing updates are broadcast
RIPv2
• A classless distance vector routing protocol that is an enhancement
of RIPv1’s features.
• Next hop address is included in updates
• Routing updates are multicast (224.0.0.9 vs. 255.255.255.255)
• The use of authentication is an option
http://www.cisco.com/univercd/cc/t
d/doc/cisintwk/ito_doc/rip.htm
5. Introduction
Similarities between RIPv1 & RIPv2
– Use of timers to prevent routing loops
– Use of split horizon or split horizon with poison
reverse to also help prevent routing loops.
– Use of triggered updates when there is a change in the
topology for faster convergence.
– Maximum hop count of 15, with the hop count of 16
signifying an unreachable network.
6. RIPv1 Limitations
LabTopology
3 router set up
Topology is discontiguous
There exists a static summary route
Static route information can be
injected into routing table updates
using redistribution.
Routers 1 & 3 containVLSM networks
Remember that both the R1 and R3
routers have subnets that are part of
the 172.30.0.0/16 major classful
network (class B).
Also remember that R1 and R3 are
connected to R2 using subnets of the
209.165.200.0/24 major classful
network (class C).
This topology is discontiguous and
will not converge because
172.30.0.0/16 is divided by the
209.165.200.0/24.
7. RIPv1 Limitations
The topology shows
that R2 has a static
summary route to the
192.168.0.0/16 network.
The configuration of
this summary route will
be displayed later in this
section.
8. RIPv1 Limitations
Review theVLSM addressing
scheme in the figure. As shown in
the top chart, both R1 and R3
have had the 172.30.0.0/16
network subnetted into /24
subnets.
–Four of these /24 subnets are
assigned:
–two to R1 (172.30.1.0/24 and
172.30.2.0/24)
–two to R3 (172.30.100.0/24 and
172.30.110.0/24).
In the bottom chart, we have
taken the 172.30.200.0/24 subnet
and subnetted it again, using the
first four bits for subnets and the
last four bits for hosts.The result
is a 255.255.255.240 mask or /28.
Subnet 1 and Subnet 2 are
assigned to R3.
9. RIPv1 Limitations
Scenario Continued
VLSM
-Recall this is sub netting the
subnet
Private IP addresses are on
LAN links
Public IP addresses are used
onWAN links (through an ISP,
or when inside users need to
access outside sites, a public
IP address must be used.)
Loopback interfaces
-These are virtual interfaces
that can be pinged and added
to routing table
Cisco has set these addresses aside for educational purposes.
10. RIPv1 Limitations
Loopback interfaces
Notice that R3 is using loopback interfaces (Lo0, Lo1,
and Lo2).
A loopback interface is a software-only interface that
is used to emulate a physical interface.
Like other interfaces, it can be assigned an IP address.
Loopback interfaces are also used by other routing
protocols, such as OSPF, for different purposes.
These uses will be discussed in Chapter 11 OSPF.
In a lab environment, loopback interfaces are useful in
creating additional networks without having to add
more physical interfaces on the router.
A loopback interface can be pinged and the subnet can
be advertised in routing updates.
Therefore, loopback interfaces are ideal for simulating
multiple networks attached to the same router.
In our example, R3 does not need four LAN interfaces
to demonstrate multiple subnets andVLSM. Instead,
we use loopback interfaces.
11. RIPv1 Limitations
Route redistribution
– Redistribution involves taking the routes from one routing
source and sending those routes to another routing source.
• In our example topology, we want the RIP process on R2 to redistribute
our static route (192.168.0.0/16) by importing the route into RIP and
then sending it to R1 and R3 using the RIP process.
-R2(config-router)#redistribute static
12. RIPv1 Limitations
R2(config)#ip route 192.168.0.0 255.255.0.0
Null0
–The address space represented by the static summary
route 192.168.0.0/16 does not actually exist.
–In order to simulate this static route, we use a null
interface as the exit interface.
– You do not need to enter any commands to create or
configure the null interface.
–It is always up but does not forward or receive traffic.
Traffic sent to the null interface is discarded.
13. Static routes and null
interfaces Static routes and null interfaces
R2(config)#ip route 192.168.0.0 255.255.0.0 Null0
a static route must have an active exit interface before
it will be installed in the routing table.
Using the null interface will allow R2 to advertise the
static route in RIP even though networks belonging to
the summary 192.168.0.0/16 do not actually exist.
14. Verifying and Testing
Connectivity show ip interfaces brief
–To test whether or not the topology has full
connectivity, we first verify that both serial
links on R2 are up using the show ip interface
brief
Ping
Whenever R2 pings any of the 172.30.0.0 subnets
on R1 or R3, only about 50% of the ICMP are
successful.
R1 is able to ping 10.1.0.1 but is unsuccessful when
attempting to ping the 172.30.100.1 on R3
R3 is able to ping 10.1.0.1 but is unsuccessful when
attempting to ping the 172.30.1.1 on R1.
15. RIPv1 Limitations
RIPv1 – a classful routing protocol
–Subnet mask are not sent in updates
–Summarizes networks at major network boundaries
–RIPv1 cannot support discontiguous networks,VLSM, or CIDR.
–if network is discontiguous and RIPv1 configured convergence will not be
reached
–RIPv1 on both the R1 and R3 routers will summarize their 172.30.0.0 subnets
to the classful major network address of 172.30.0.0 when sending routing
updates to R2.
–From the perspective of R2, both updates have an equal cost of 1 hop to reach
network 172.30.0.0/16. As you will see, R2 installs both paths in the routing
table.
16. RIPv1 Limitations
Examining the routing tables
-To examine the
contents of routing
updates use the debug
ip rip command
R2 is receiving two 172.30.0.0 equal cost
routes with a metric of 1 hop. R2 is
receiving one route on Serial 0/0/0 from R1
and the other route on Serial 0/0/1 from R3.
R2 has two equal cost routes to the
172.30.0.0/16 network.
17. RIPv1 Limitations
•R1 has its own 172.30.0.0 routes:
172.30.2.0/24 and 172.30.1.0/24.
•But R1 does not send R2 those subnets.
•R3 has a similar routing table.
•Both R1 and R3 are boundary routers and
are only sending the summarized
172.30.0.0 network to R2 in their RIPv1
routing updates.
•As a result, R2 only knows about the
172.30.0.0/16 classful network and is
unaware of any 172.30.0.0 subnets.
•R2 that it is not including the 172.30.0.0 network
in its updates to either R1 or R3.
•Because the split horizon rule is in effect.
•R2 learned about 172.30.0.0/16 on both the
Serial 0/0/0 and Serial 0/0/1 interfaces, it does not
include that network in updates it sends out these
same interfaces.
18. RIPv1 Limitations
Because RIPv1 does not send the
subnet mask in routing updates, it
cannot supportVLSM.
R3 router is configured withVLSM
subnets, all of which are members of
the class B network 172.30.0.0/16:
–172.30.100.0/24 (FastEthernet 0/0)
–172.30.110.0/24 (Loopback 0)
–172.30.200.16/28 (Loopback 1)
–172.30.200.32/28 (Loopback 2)
As we saw with the 172.30.0.0/16
updates to R2 by R3,
–RIPv1 either summarizes the
subnets to the classful boundary
–or uses the subnet mask of the
outgoing interface to determine
which subnets to advertise.
R4 is added to
the topology
connected to R3
19. RIPv1 Limitations
Why is RIPv1 on R3 not including the
other subnets, 172.30.200.16/28 and
172.30.200.32/28, in updates to R4?
– Those subnets do not have the same
subnet mask as FastEthernet 0/0.
– R3 will only include those 172.30.0.0
routes in its routing table with the
same mask as the exit interface.
– Since the interface is 172.30.100.1
with a /24 mask, it will only include
172.30.0.0 subnets with a /24 mask.
The only one that meets this
condition is 172.30.110.0.
– The other 172.30.0.0 subnets,
172.30.200.16/28 and
172.30.200.32/28, are not included
because the /28 masks do not match
the /24 mask of the outgoing
interface.
R4 is added to
the topology
connected to R3
20. RIPv1 Limitations
No CIDR Support
R2(config)#ip route 192.168.0.0
255.255.0.0 Null0
–the static route is included in
R2's routing table, but R2 will
not include the static route in its
update
–R1 is not receiving this
192.168.0.0/16 route in its RIP
updates from R2,
Reason: Classful routing
protocols do not support
CIDR routes that are
summarized with a smaller
mask than the classful
subnet mask
–If the 192.168.0.0 static route
were configured with a /24 mask
or greater, this route would be
included in the RIP updates.
21. Configuring RIPv2
Comparing RIPv1 & RIPv2 Message Formats
–RIPv2 Message format is similar to RIPv1 but has 2 extensions
1st extension is the subnet mask field
allows a 32 bit mask to be included in the RIP route entry.
the receiving router no longer depends upon the subnet mask of the inbound
interface or the classful mask when determining the subnet mask for a route
2nd extension is the addition of next hop address
The Next Hop address is used to identify a better next-hop address - if one exists -
than the address of the sending router.
If the field is set to all zeros (0.0.0.0), the address of the sending router is the best
next-hop address.
22. Configuring RIPv2
Enabling andVerifying RIPv2
Configuring RIP on a Cisco router
–By default it is running RIPv1
–Even though the router only sends RIPv1
messages, it can interpret both RIPv1 and RIPv2
messages.
–A RIPv1 router will just ignore the RIPv2 fields in
the route entry.
RIPv1 RIPv2
23. Configuring RIPv2
Configuring RIPv2 on
a Cisco router
-Requires using the
version 2 command
-RIPv2 ignores RIPv1
updates
To verify RIPv2 is
configured use the
show ip protocols
command
24. Comparing RIP v1 and v2
RIP v2 send and receive v2
RIP v1 send v1 but can receive both v1 and v2
Version 1 Version 2
No. I can not
take version 1
Yes. I can
take version 1
or 2
I can only send
version 1
I can only send
version 2
RIP network is broken
25. POP Quiz
How do you make the RIPv2 back to the default “send 1” and receive 1 or
2”?
- Hint: Gad(config-router)#version 1 is not the answer.
Version 1 Version 2
26. Configuring RIPv2
Auto-Summary &
RIPv2
RIPv2 will
automatically
summarize routes at
major network
boundaries and can
also summarize routes
with a subnet mask
that is smaller than
the classful subnet
27. Configuring RIPv2
Disabling Auto-
Summary in RIPv2
To disable
automatic
summarization
issue the no auto-
summary
command
28. Configuring RIPv2
Verifying RIPv2 Updates
When using RIPv2 with automatic summarization
turned off
Each subnet and mask has its own specific entry,
along with the exit interface and next-hop
address to reach that subnet.
To verify information being sent by RIPv2 use the
debug ip rip command
29. VLSM & CIDR
RIPv2 andVLSM
Networks using a
VLSM IP addressing
scheme
Use classless
routing protocols (i.e.
RIPv2) to
disseminate
network addresses
and their subnet
30. VLSM & CIDR
CIDR uses Supernetting
Supernetting is a bunch of contiguous
classful networks that is addressed as
a single network.
31. VLSM & CIDR
To verify that
supernets are
being sent and
received use the
following
commands
-Show ip
route
-Debug ip rip
32. Verifying & Troubleshooting
RIPv2 BasicTroubleshooting steps
-Check the status of all links
-Check cabling
-Check IP address & subnet mask
configuration
-Remove any unneeded configuration
commands
Commands used to verify proper operation of
RIPv2
–Show ip interfaces brief
–Show ip protocols
33. Verifying & Troubleshooting
RIPv2 Common RIPv2 Issues
When trouble shooting RIPv2 examine the following issues:
Version
Check to make sure you are using version 2
Network statements
Network statements may be incorrectly typed
or missing
Automatic summarization
If summarized routes are not needed then disable
automatic summarization
34. Verifying & Troubleshooting
RIPv2 Reasons why it’s good to authenticate routing information
-Prevent the possibility of accepting invalid routing updates
-Contents of routing updates are encrypted
Types of routing protocols that can use authentication
-RIPv2
-EIGRP
-OSPF
-IS-IS
-BGP