Diese Präsentation wurde erfolgreich gemeldet.
Wir verwenden Ihre LinkedIn Profilangaben und Informationen zu Ihren Aktivitäten, um Anzeigen zu personalisieren und Ihnen relevantere Inhalte anzuzeigen. Sie können Ihre Anzeigeneinstellungen jederzeit ändern.
Steps for ST St C
• Prefabricated crowns form
• Adapted to individual teeth
• Cemented on teeth with a biocompatible
lutin...
Use of Stainless Steel Crowns
u Introduced to pediatric dentistry by Dr. William
Humphrey in 1950
– prior to that orthodon...
Success of the stainless steel
crown
• The quality of the tooth preparation
• Selection and adjustment of the of an
approp...
Indications
u Extensive caries
u Pulpotomy/pulpectomy
u Malformed teeth
u Fractured teeth
u Severe attrition of primary te...
Contraindications
u Esthetics
u Teeth that are nearing exfoliation
u Mechanical problems
– space loss
– caries beneath the...
Types of SSC
• 1- Non contoured
untrimmed crown
They has straight
sides
They are longer than
the length of the teeth
They ...
• 2- Pretrimmed ( prefestonned ) crown
Has straight sides
straight longer than the teeth
already trimmed to follow the gin...
• 3- Pre contoured crown
It is trimmed and also contoured
its margins curved inward
it is in the right length for the aver...
What you will need
u Burs and stones
– #169
– heatless stone
u Pliers and instruments
– contouring plier
– crimping plier
...
Steps for St St C
• Local anesthesia administration
• Rubber dam isolation
• Wooden wedge placement or T band
to avoid dam...
Overview
u Occlusal reduction
u Proximal reduction
u Buccal and lingual
reduction
u Beveling
u Round all sharp line
angles...
Step by Step
u Caries removal
u Complete pulp therapy if necessary Proceed with
crown preparation
u Occlusal Reduction - 1...
Proximal Reduction
u Contact with adjacent teeth must be broken
gingivally and buccolingually
u proximal slices converge s...
Angulation of Slices
Proper slice Improper slice
Ledging
u Proximal slice must
be extended below
tissue to avoid
leaving a ledge
Preserving the Outline
u Remember: crown preparation if a significant part
of the crown’s retentive potential
Buccal-Lingual Reduction
u Reduction is optional and is undertaken only if
the buccal or lingual bulges are so prominent
t...
Beveling
u A bevel at an angle of 30-45 degrees
removes the sharp cusp tips and creates a
gentle slope in the occlusal thi...
Round Sharp Line Angles
u The buccal and lingual
proximal line angles are
rounded by holding the bur
parallel to the tooth...
Crown Adaptation
u Mark gingival line with a scaler & trim 1mm
beneath the mark using C&B scissors Margins
should be trimm...
Guidelines
u Resistance in seating without tissue blanching.
Check for
– high spots on occlusal surface
– ledges
u Resista...
Gingival Contours
Buccal gingival contour of first
primary molar-- stretched-out S
Proximal gingival contour of
primary mo...
Contour the Crown
u Use contouring pliers, bend the gingival third
of the crown’s margins inward to restore
anatomic margi...
Crown Adaptation
Poor marginal seal may allow
micro leakage of bacteria and their toxic products leading
to recurrent deca...
• Marginal ridge are level with those of
adjacent teeth.
• Contacts are restored.
• No extensive blanching of the gingiva ...
Finishing and Polishing
u Use heatless stone to smooth jagged edges
u Then use a rubber wheel to remove small
scratches an...
The crown margins should have
• Smooth edges
• Edges free of burs
• Knife edge margins
• Smooth curved margins
• No riples...
Cementation
u Clean crown and tooth
u Fill crown with zinc phosphate cement
u Seat crown, expressing cement form all margi...
Crown cementation
• The following cements can be used
Polycarboxylate cement
advantages:
*minimal irritation effect on the...
Glassionomer cement
• Advantages:
*Have the potential to adhere to tooth structure
*Fluoride release
• Disadvantages:
*Moi...
• Zinc phosphate cements:
• Because of its low pH
• lack of antibacterial properties.
• solubility in oral fluids
• lack o...
• Adhesive cements
• Advantage
Improve the retention
Reduce micro-leakage
• Disadvantages
They are more difficult to manip...
• Before cementation, a cavity varnish must
be applied on a vital tooth.
• Clean and dry the crown and the tooth
(partial ...
• Remove excess cement with explorer on
labial and lingual and with loss
• Excess cement can produce gingival
inflammation...
Post-op instructions ?
u Although a well-adapted and cemented
crown should not come off under these
circumstances, patient...
Some problems and their solutions
1-Crowns does not seat properly
• This usually means that there is a ledge. It is
remove...
Clinical Variations
u “Back-to-back”
chrome crowns
Second primary
molars
Possible solutions to this problem:
1-The crown is rotated slightly mesio-buccally so
that it is rotated slightly out of t...
Placement of the adjacent crowns
• Tooth preparation and crown selection for
placing multiple crowns are similar to the
te...
• Prepare the occlusal reduction of one tooth
completely before beginning the occlusal
reduction of the other tooth. When ...
• Crowns should be trimmed, contoured and
prepared for cementation
• It is generally best to begin placement and
cementati...
Restoration of Class IV Caries in
Primary Anterior Teeth
u Esthetic Resin Restoration
u Stainless Steel Crown
u Open-Face ...
Anterior Stainless Steel Crowns
u Esthetics - poor
u Durability - very good
u Time for placement - fastest
u Selection cri...
Open Faced Stainless Steel Crown
u Esthetics - okay
u Durability - good, although facing may be
dislodgedTime for placemen...
Crown Form Selection
u Select the appropriate crown form size
from the mesio-distal measurement (mm)
of the tooth’s incisa...
Tooth Preparation
u Incisal reduction
– 1-1.25 mm
u Proximal reduction - parallel mesial and
distal slices to break contac...
Tooth Preparation
u Buccal reduction - to allow the placement of the
restoration within the normal buccal lingual
width of...
Circumfrential Undercut Shoulder
u Terminates at the crest of the gingiva
u Shoulder depth should be .75-1 mm
u Use invert...
Variation
Cervical undercut on facial only
Removal of caries may also provide undercuts
Crown Adaptation
u Carefully trim off the cervical collar with
curved festooning scissorsTrim crown form
so that when seat...
Trial Fitting of Crown Form
u Try on trimmed crown formIncisal
edges should line upPlace hole in
incisal edge of crown wit...
Crown Placement
u Etch tooth with phosphoric acid for 30 seconds
u Thoroughly wash and dry etched surface
u Apply bonding ...
Minimal Finishing and Polishing
u Peel it away from composite crown
u Finish margins
u Adjust occlusion
u DO NOT FINISH th...
Nächste SlideShare
Wird geladen in …5
×

Pedia stainless steel crown

Pediatric Dentistry I
Forth Year

Ähnliche Bücher

Kostenlos mit einer 30-tägigen Testversion von Scribd

Alle anzeigen

Ähnliche Hörbücher

Kostenlos mit einer 30-tägigen Testversion von Scribd

Alle anzeigen
  • Als Erste(r) kommentieren

Pedia stainless steel crown

  1. 1. Steps for ST St C • Prefabricated crowns form • Adapted to individual teeth • Cemented on teeth with a biocompatible luting agent • Used mainly to preserve primary teeth till the normal age of exfoliation • Can be used newly erupted permanent or (immature tooth) as a semi permanent restoration
  2. 2. Use of Stainless Steel Crowns u Introduced to pediatric dentistry by Dr. William Humphrey in 1950 – prior to that orthodontic bands filled with amalgam were a last resort – “necessity is the mother of invention” u Considered superior to large multisurface amalgam restorations and have a longer clinical lifespan than two or three surface amalgams (Dawson et al., 1981)
  3. 3. Success of the stainless steel crown • The quality of the tooth preparation • Selection and adjustment of the of an appropriate crown • The luting cement
  4. 4. Indications u Extensive caries u Pulpotomy/pulpectomy u Malformed teeth u Fractured teeth u Severe attrition of primary teeth u Mesial lesions on first primary molars u Semi-permanent restorations on young permanent molars
  5. 5. Contraindications u Esthetics u Teeth that are nearing exfoliation u Mechanical problems – space loss – caries beneath the level of the bone u Permanent restoration in the permanent dentition
  6. 6. Types of SSC • 1- Non contoured untrimmed crown They has straight sides They are longer than the length of the teeth They require trimming and contouring
  7. 7. • 2- Pretrimmed ( prefestonned ) crown Has straight sides straight longer than the teeth already trimmed to follow the gingival contour trimming is minimal but contouring is required
  8. 8. • 3- Pre contoured crown It is trimmed and also contoured its margins curved inward it is in the right length for the average tooth in many cases it fits accurately with out alteration
  9. 9. What you will need u Burs and stones – #169 – heatless stone u Pliers and instruments – contouring plier – crimping plier u Polishing
  10. 10. Steps for St St C • Local anesthesia administration • Rubber dam isolation • Wooden wedge placement or T band to avoid damaging the adjacent tooth structure
  11. 11. Overview u Occlusal reduction u Proximal reduction u Buccal and lingual reduction u Beveling u Round all sharp line angles and corners
  12. 12. Step by Step u Caries removal u Complete pulp therapy if necessary Proceed with crown preparation u Occlusal Reduction - 1.0-1.5mm Connect the Depth Cuts Check reduction with opposing arch
  13. 13. Proximal Reduction u Contact with adjacent teeth must be broken gingivally and buccolingually u proximal slices converge slightly toward the occlusal and lingual – DO NOT OVER TAPER u The gingival margins should have a feather- edge finish line u Adjacent tooth structure must not be damaged
  14. 14. Angulation of Slices Proper slice Improper slice
  15. 15. Ledging u Proximal slice must be extended below tissue to avoid leaving a ledge
  16. 16. Preserving the Outline u Remember: crown preparation if a significant part of the crown’s retentive potential
  17. 17. Buccal-Lingual Reduction u Reduction is optional and is undertaken only if the buccal or lingual bulges are so prominent that the constricted margin of the crown will not go over he height of contour – when required, no more than .5-1mm should be removed – reductions must end in a feather edge
  18. 18. Beveling u A bevel at an angle of 30-45 degrees removes the sharp cusp tips and creates a gentle slope in the occlusal third of the lingual and buccal surfaces
  19. 19. Round Sharp Line Angles u The buccal and lingual proximal line angles are rounded by holding the bur parallel to the tooth’s long axis and blending the surfaces togetherThe finished contour should conform to the internal contour of the stainless steel crown
  20. 20. Crown Adaptation u Mark gingival line with a scaler & trim 1mm beneath the mark using C&B scissors Margins should be trimmed to lie parallel with the contour of the gingival tissue and consist of a series of curves without sharp angles
  21. 21. Guidelines u Resistance in seating without tissue blanching. Check for – high spots on occlusal surface – ledges u Resistance in seating with tissue blanching. Check for – crown too wide (preliminary contouring) – crown too long – tissue caught in margin
  22. 22. Gingival Contours Buccal gingival contour of first primary molar-- stretched-out S Proximal gingival contour of primary molars -- frown Buccal gingival contour of second primary molar-- smile
  23. 23. Contour the Crown u Use contouring pliers, bend the gingival third of the crown’s margins inward to restore anatomic margins and to reduce the marginal circumference ensuring a good fit u Crimp the crown u With the crown-crimping plier (#118) crimp the margin Replace crown on tooth and check margins with an explorer
  24. 24. Crown Adaptation Poor marginal seal may allow micro leakage of bacteria and their toxic products leading to recurrent decay or pulp inflammation. • It may be necessary to remove the rubber dam at this stage. • Try the crown on the tooth. • Seating the crown is from the less to more bulging surface, • e.g. from buccal to palatal in maxillary teeth, and from lingual to buccal in mandibular teeth • Evaluate the opposite arch for proper cusp and occlusal interdigitaion.
  25. 25. • Marginal ridge are level with those of adjacent teeth. • Contacts are restored. • No extensive blanching of the gingiva to avoid trauma to the gingival tissue.
  26. 26. Finishing and Polishing u Use heatless stone to smooth jagged edges u Then use a rubber wheel to remove small scratches and smooth u Polish surface of crown to a high shine with tripoli and rouge
  27. 27. The crown margins should have • Smooth edges • Edges free of burs • Knife edge margins • Smooth curved margins • No riples or bend • No scratches
  28. 28. Cementation u Clean crown and tooth u Fill crown with zinc phosphate cement u Seat crown, expressing cement form all margins and press into occlusion u Remove excess cement when partially set
  29. 29. Crown cementation • The following cements can be used Polycarboxylate cement advantages: *minimal irritation effect on the pulp *there is some adhesion between tooth substance and st, st, alloys Disadvantages: *Require precise preparation and manipulation *need clean and uncontaminated tooth surface
  30. 30. Glassionomer cement • Advantages: *Have the potential to adhere to tooth structure *Fluoride release • Disadvantages: *Moisture sensitivity * Initial slow set. * Some pulp irritation. Crown cementation
  31. 31. • Zinc phosphate cements: • Because of its low pH • lack of antibacterial properties. • solubility in oral fluids • lack of adhesion, they are not recommended for cementation of Stainless steel crown in primary molar. Crown cementation
  32. 32. • Adhesive cements • Advantage Improve the retention Reduce micro-leakage • Disadvantages They are more difficult to manipulate, More technique sensitive and more expensive than conventional cements. Crown cementation
  33. 33. • Before cementation, a cavity varnish must be applied on a vital tooth. • Clean and dry the crown and the tooth (partial isolation until setting of the cement). • Fill the crown with the cement while the mix is glossy. • Seat the crown firmly into occlusion, • instruct the patient to bite on the seater to ensure complete seating. Crown cementation
  34. 34. • Remove excess cement with explorer on labial and lingual and with loss • Excess cement can produce gingival inflammation and discomfort. • Make a final check and follow-up. Crown cementation
  35. 35. Post-op instructions ? u Although a well-adapted and cemented crown should not come off under these circumstances, patients and parents should be warned of the possibility
  36. 36. Some problems and their solutions 1-Crowns does not seat properly • This usually means that there is a ledge. It is removed using a tapered fissure bur. u May need to increase the buccal and lingual reductions u May need to compress crown form on mesial and distal with Howe pliers •
  37. 37. Clinical Variations u “Back-to-back” chrome crowns Second primary molars
  38. 38. Possible solutions to this problem: 1-The crown is rotated slightly mesio-buccally so that it is rotated slightly out of the arch. 2- The closest fitting crown is held in the beaks of Adams pliers and squeezed mesio-distally to reduce this dimension. This is an effective way of flattening the contact points. 3- If difficulty is still encountered, additional tooth reduction of the buccal and lingual surfaces and selection of another smaller crown.
  39. 39. Placement of the adjacent crowns • Tooth preparation and crown selection for placing multiple crowns are similar to the technique previously described for single crowns, but with a few additional factors
  40. 40. • Prepare the occlusal reduction of one tooth completely before beginning the occlusal reduction of the other tooth. When reduction of the two teeth is performed simultaneously, the tendency is to under-reduce both. • Insufficient proximal reduction is a common problem. Contact between adjacent proximal surfaces should be broken producing approximately 1.5 mm space at the gingival level. Placement of the adjacent crowns
  41. 41. • Crowns should be trimmed, contoured and prepared for cementation • It is generally best to begin placement and cementation of the more distal crown first. • The sequence of placement of crowns for cementation should follow the same sequence as that used when the crowns are placed for the final fitting. Placement of the adjacent crowns
  42. 42. Restoration of Class IV Caries in Primary Anterior Teeth u Esthetic Resin Restoration u Stainless Steel Crown u Open-Face Steel Crowns u Composite Crowns Composite Crowns
  43. 43. Anterior Stainless Steel Crowns u Esthetics - poor u Durability - very good u Time for placement - fastest u Selection criteria - severely decayed, esthetics of minimal importance, gingival hemorrhage not controlled, inadequate patient cooperation
  44. 44. Open Faced Stainless Steel Crown u Esthetics - okay u Durability - good, although facing may be dislodgedTime for placement - takes longest to place due to two-step procedureSelection criteria - severely decayed teeth, durabilty needed, esthetics are a concern
  45. 45. Crown Form Selection u Select the appropriate crown form size from the mesio-distal measurement (mm) of the tooth’s incisal edge, or by direct comparison
  46. 46. Tooth Preparation u Incisal reduction – 1-1.25 mm u Proximal reduction - parallel mesial and distal slices to break contact with the adjacent tooth and to allow enough bulk to give strength to the final restoration – .5-1 mm
  47. 47. Tooth Preparation u Buccal reduction - to allow the placement of the restoration within the normal buccal lingual width of the tooth restored – .5-1 mm u Lingual reduction - to allow for the necessary bulk for the strength of the crown and to prevent for any occlusal interferences
  48. 48. Circumfrential Undercut Shoulder u Terminates at the crest of the gingiva u Shoulder depth should be .75-1 mm u Use inverted cone
  49. 49. Variation Cervical undercut on facial only Removal of caries may also provide undercuts
  50. 50. Crown Adaptation u Carefully trim off the cervical collar with curved festooning scissorsTrim crown form so that when seated, it covers the shoulder but extends no more than 1 mm past tge shoulder
  51. 51. Trial Fitting of Crown Form u Try on trimmed crown formIncisal edges should line upPlace hole in incisal edge of crown with an explorer to allow vent for composite to flow through during crown placement
  52. 52. Crown Placement u Etch tooth with phosphoric acid for 30 seconds u Thoroughly wash and dry etched surface u Apply bonding agent according to specifications u Carefully pack the crown form resin to avoid entrapment of air bubbles u Position the filled crown form over the prepared tooth so it extends 1mm over the gingival margin u Remove excess resin from margins with an explorer before polymerizing u Slice crown form
  53. 53. Minimal Finishing and Polishing u Peel it away from composite crown u Finish margins u Adjust occlusion u DO NOT FINISH the labial surface – polymerization of the resin against the plastic provides the smoothest and most stain resistant surface

×