8. These data sheets can be performed with
your own company logo and corporate identity
supplying data for buildings
with a residential function
page 01
theFloorheater eu
for a professional layout plan
For only a tube layout drawing fill in pages 1, 2 and 3
For only a heat loss calculation fill in page 2 (only T area [°C]) and page 4
For a tube layout drawing and a heat loss calculation fill in all fields
If certain values or details are unknown average values will be used.
Supply a drawing in a DWG or DXF extenstion. If you don't have these, a PDF can be converted to a DWG file or the PDF
can be used as an underlayer. A JPG (or another pixel extension) can also be used as an underlayer.
Supply water temperature [o
C]
Screed type (cement, seamless floor, other ...)
Screed thickness [cm]
Tubes diameter [mm]
Isolation
Construction floor
Screed
Floor covering
Tube
Hart to hart distance C/CFloor structure
Remarks or comments
9. supplying data for buildings
with a residential function
page 02
theFloorheater eu
for a professional layout plan
Remarks or comments
Rooms C/C [cm]* T room [o
C] type floor covering
Table with common / average values of roomtemperatures in °C
Elderly and nursing homes o
C
Living area 22
Bathroom 25
Toilet 18
Technical area 18
Unnamed 10
Storage 10
Houses o
C
Living area 20
Bathroom 22
Toilet 15
Technical area 10
Unnamed 10
Storage 10
* If there is also a heat loss calculation to be made this field can be left open. These centre distance will be determined based on the heat loss calculation.
10. supplying data for buildings
with a residential function
page 03
theFloorheater eu
for a professional layout plan
Remarks or comments
Name the positions of the manifold(s) if they are not
shown on the drawing:
How many groups can be used maxiumum on one manifold?
Supply- and returnpipes always through doorways
Always the shortest way for supply- and returnpipes (cutouts through walls)
The shortest way for supply- and returnpipes but where possible trough doorways
Are there edge zones applied? yes/no | If yes, where?
Bifilar / Snail pattern
Spiral pattern
There is no floor cooling to be used
There is floor cooling to be used
11. supplying data for buildings
with a residential function
page 04
theFloorheater eu
for a professional layout plan
Is there ventilation to be used? yes/no
If yes, choose one of the possibilities below:
Natural supply/natrural extraction
Natural supply/mechanical extraction
Mechanical supply/natural extraction
Mechanical supply/mechanical extraction
Is the ventilation air pre-heated? yes/no
If yes, what is the supply temperature of the ventilation air?
Is there a night setback applied or a continuous operating system?
What kind of temperature control is there to be used:
One central controller, In which room?
Individual zone control per room
Partition wall Rc value
Enter the Rc Values for the different partitions walls
12.
13. These data sheets can be performed with
your own company logo and corporate identity
supplying data for buildings
with an utility function
page 01
theFloorheater eu
for a professional layout plan
For only a tube layout drawing fill in pages 1, 2 and 3
For only a heat loss calculation fill in page 2 (only T area [°C]) and page 4
For a tube layout drawing and a heat loss calculation fill in all fields
If certain values or details are unknown, average values will be used.
Supply a drawing in a DWG or DXF extenstion. If you don't have these, a PDF can be converted to a DWG file or the PDF
can be used as an underlayer. A JPG (or another pixel extension) can also be used as an underlayer.
Supply water temperature [o
C]
Screed type (cement, seamless floor, other ...)
Screed thickness [cm]
Tubes diameter [mm]
Isolation
Construction floor
Screed
Floor covering
Tube
Hart to hart distance C/CFloor structure
Remarks or comments
14. page 02
theFloorheater eu
for a professional layout plan
Remarks or comments
Rooms C/C [cm]* T room [o
C] type floor covering
Table with common / average values of roomtemperatures in °C
Nursing -and health function o
C
Living area 22
Bathroom 25
Toilet 18
Technical area 18
Unnamed 10
Storage 10
Office function, education function, etc. o
C
Living area 20
Bathroom 22
Toilet 15
Technical area 10
Unnamed 10
Storage 10
* If there is also a heat loss calculation to be made this field can be left open. These centre distance will be determined based on the heat loss calculation.
supplying data for buildings
with an utility function
15. Remarks or comments
Name the positions of the manifold(s) if they are not
shown on the drawing:
How many groups can be used maxiumum on one manifold?
Supply- and returnpipes always through doorways
Always the shortest way for supply- and returnpipes (cutouts through walls)
The shortest way for supply- and returnpipes but where possible trough doorways
Are there edge zones applied? yes/no | If yes, where?
Bifilar / Snail pattern
Spiral pattern
There is no floor cooling to be used
There is floor cooling to be used
page 03
theFloorheater eu
for a professional layout plan
supplying data for buildings
with an utility function
16. page 04
theFloorheater eu
for a professional layout plan
supplying data for buildings
with an utility function
Is there ventilation to be used? yes/no
If yes, choose one of the possibilities below:
Natural supply/natrural extraction
Natural supply/mechanical extraction
Mechanical supply/natural extraction
Mechanical supply/mechanical extraction
Is the ventilation air pre-heated? yes/no
If yes, what is the supply temperature of the ventilation air?
Is there a night setback applied or a continuous operating system?
What kind of temperature control is there to be used:
One central controller, In which room?
Individual zone control per room
Partition wall Rc value
Enter the Rc Values for the different partitions walls
Is there a downgraded ceiling? yes/no
If yes, is this more or less open than 20% of the total area? more/less
17.
18. These data sheets can be performed with
your own company logo and corporate identity
supplying data for buildings
with an industrial function
page 01
theFloorheater eu
for a professional layout plan
For only a tube layout drawing fill in pages 1, 2 and 3
For only a heat loss calculation fill in page 2 (only T area [°C]), 4 and 5
For a tube layout drawing and a heat loss calculation fill in all fields
If certain values or details are unknown average values will be used.
Supply a drawing in a DWG or DXF extenstion. If you don't have these, a PDF can be converted to a DWG file or the PDF
can be used as an underlayer. A JPG (or another pixel extension) can also be used as an underlayer.
Supply water temperature [o
C]
Screed type (cement, seamless floor, other ...)
Screed thickness [cm]
Tubes diameter [mm]
Isolation
Construction floor
Screed
Floor covering
Tube
Hart to hart distance C/CFloor structure
Remarks or comments
19. page 02
theFloorheater eu
for a professional layout plan
Remarks or comments
Rooms C/C [cm]* T room [o
C] type floor covering
Table with common / average values of temperatures in °C
* If there is also a heat loss calculation to be made this field can be left open. These centre distance will be determined based on the heat loss calculation.
Type of activity o
C
low activity: general sedentary work such as office, laboratory 20
low activity: general sedentary work and occasionally getting up and walking 18
moderate activity: light industry with hand and arm work or walk with speed between 3.5 and 5.5 km/h 15
high activity: heavy industry with hand and arm work or carrying loads 12
very high activity: heavy arm and trunk work and hauling 10
supplying data for buildings
with an industrial function
20. page 03
theFloorheater eu
for a professional layout plan
Remarks or comments
Name the positions of the manifold(s) if they are not
shown on the drawing:
How many groups can be used maxiumum on one manifold?
Supply- and returnpipes always through doorways
Always the shortest way for supply- and returnpipes (cutouts through walls)
The shortest way for supply- and returnpipes but where possible trough doorways
Are there edge zones applied? yes/no | If yes, where?
Bifilar / Snail pattern
Spiral pattern
There is no floor cooling to be used
There is floor cooling to be used
supplying data for buildings
with an industrial function
21. page 04
theFloorheater eu
for a professional layout plan
supplying data for buildings
with an industrial function
What kind of temperature control is there to be used:
optimizing control
Not optimizing control with natural ventilation
Not optimizing control with mechanical ventilation
Is there a discontinuous flow of material having a lower temperature? yes/no
If yes, what material and with which mass?
Is there heat gain of:
Continuous transit of hot products through space? yes/no
If yes, what is the average surface and surface temperature?
Heat generation by processes? yes/no
If yes, what is the electrical power?
Is there ventilation to be used? yes/no
If yes, choose one of the possibilities below:
Natural supply/natrural extraction
Natural supply/mechanical extraction
Mechanical supply/natural extraction
Mechanical supply/mechanical extraction
Is the ventilation air pre-heated? yes/no
If yes, what is the supply temperature of the ventilation air?
Is there a night setback applied or a continuous operating system?
What kind of temperature control is there to be used:
One central controller, In which room?
Individual zone control per room
22. page 05
theFloorheater eu
for a professional layout plan
supplying data for buildings
with an industrial function
Partition wall Rc value
Enter the Rc Values for the different partitions walls
Is there any heat loss to cold surfaces? yes/no
If yes, what is the surface area and the average surface temperature?
Is there heat loss by local suction? yes/no
If yes, what is the flow rate of the exhaust air?
which is the temperature of the supplied air?
Remarks or comments
