1.
FED-C Series
Quick Start Guide

2.
Contents
Safety Information and Precautions .......................................................................................................2
1. Product Information ............................................................................................................................3
1.1 Nameplate and Designation Rule......................................................................................................................3
1.2 eneral Speci cations.......................................................................................................................................4
1.3 Environment.......................................................................................................................................................5
2 Wiring ..................................................................................................................................................6
2.1 Typical System Connection ...............................................................................................................................6
2.2 Terminal Description ..........................................................................................................................................7
2.3 Remove the EMC and VDR Screws.................................................................................................................8
3 Operating Panel...................................................................................................................................9
3.1 Get Familiar with Operating Panel.....................................................................................................................9
4 Quick Setup.......................................................................................................................................11
4.1 Setup Flowchart............................................................................................................................................... 11
5. Parameter Table ...............................................................................................................................17
5.1 Introduction......................................................................................................................................................17
5.2 Standard Parameters.......................................................................................................................................17
5.3 Monitoring Function Code................................................................................................................................30
6. Troubleshooting................................................................................................................................31
6.1 AC Drive Performance Fine Tuning .................................................................................................................31
6.2 Fault Codes and Troubleshooting....................................................................................................................32
6.3 Symptoms and Diagnostics .............................................................................................................................35
Revision History.....................................................................................................................................36

3.
Safety Information and Precautions
- 2 -
Safety Information and Precautions
This guide is packaged together with the product for AC Drive. It contains basic information for quick start of the drive. For
safety and more information, please refer to the AC Drive User Manual, which can be downloaded on website: http://www.
Engineering.com.
Electrical Safety
Extreme care must be taken at all times when working with the AC Drive or within the area of the AC Drive. The voltages used in the AC
Drive can cause severe electrical shock or burns and is potentially lethal. Only authori ed and quali ed personnel should be allowed to
work on AC Drives.
Machine/System Design and Safety of Personnel
Machine/system design, installation, commissioning startups and maintenance must be carried out by personnel who have the necessary
training and experience. They must read this safety information and the contents of this manual. If incorrectly installed, the AC Drive may
present a safety hazard.
The AC Drive uses high voltages and currents (including DC), carries a high level of stored electrical energy in the DC bus capacitors
even after power OFF. These high voltages are potentially lethal.
The AC Drive is NOT intended to be used for safety related applications/functions. The electronic “STOP &START” control circuits
within the AC Drive must not be relied upon for the safety of personnel. Such control circuits do not isolate mains power voltages from
the output of the AC Drive. The mains power supply must be disconnected by an electrical safety isolation device before accessing the
internal parts of the AC Drive.
Safety risk assessments of the machine or process system which uses an AC Drive must be undertaken by the user and or by their
systems integrator/designer. In particular the safety assessment/design must take into consideration the consequences of the AC
Drive failing or tripping out during normal operation and whether this leads to a safe stop position without damaging machine, adjacent
equipment and machine operators/users. This responsibility lies with the user or their machine/process system integrator.
The system integrator/designer must ensure the complete system is safe and designed according to the relevant safety
standards. Technology and Authorized Distributors can provide recommendations related to the AC drive to
ensure long term safe operation.
Electrical Installation - Safety
Electrical shock risk is always present within an AC Drive including the output cable leading to the motor terminals. Where dynamic brake
resistors are tted external to the AC Drive, care must be taken with regards to live contact with the brake resistors, terminals which are
at high DC voltage and potentially lethal. Cables from the AC Drive to the dynamic brake resistors should be double insulated as DC
voltages are typically 300 to 400 VDC.
Mains power supply isolation switch should be tted to the AC Drive. The mains power supply must be disconnected via the isolation
switch before any cover of the AC Drive can be removed or before any servicing work is undertaken stored charge in the DC bus
capacitors of the PWM inverter is potentially lethal after the AC supply has been disconnected. The AC supply must be isolated at least
10 minutes before any work can be undertaken as the stored charge will have been discharged through the internal bleed resistor tted
across the DC bus capacitors.
Whenever possible, it is good practice to check the DC bus voltage with a VDC meter before accessing the inverter bridge. Where the
AC Drive input is connected to the mains supply with a plug and socket, then upon disconnecting the plug and socket, be aware that
the plug pins may be exposed and internally connected to the DC bus capacitors (via the internal bridge recti er in reversed bias). Wait
10 minutes to allow stored charge in the DC bus capacitors to be dissipated by the bleed resistors before commencing work on the AC
Drive.
Electrical Shock Hazard
Ensure the protective earthing conductor complies with technical standards and local safety regulations. Because the leakage current
exceeds 3.5 mA in all models, IEC 61800-5-1 states that either the power supply must be automatically disconnected in case of
discontinuity of the protective earthing conductor or a protective earthing conductor with across-section of at least 10 mm2
(Cu) or 16
mm2
(Al) must be used. Or use two PE wires and each wire must satisfy the IEC requirements independently. Failure to comply may
result in death or serious injury.
When using an earth leakage circuit breaker, use a residual current operated protective device (RCD) of type B (breaker which can
detect both AC and DC). Leakage current can cause unprotected components to operate incorrectly. If this is a problem, lower the carrier
frequency, replace the components in question with parts protected against harmonic current, or increase the sensitivity amperage of the
leakage breaker to at least 100 mA per drive.
Factors in determining leakage current:
Size of the AC drive
AC drive carrier frequency
Motor cable type and length
EMI/RFI lter

4.
1 Product Information
- 3 -
1. Product Information
1.1 Nameplate and Designation Rule
MODEL: FED1.5C1-SB
INPUT: 1PH AC 200-240V 27.0A 50Hz/60Hz
OUTPUT: 3PH AC 0-240V 11.0A 0-500Hz 2.2kW
S : Serial Number
AC drive model
Rated input
Rated output
S/N code
Nameplate
Manufacturer
PRG
MF.K
ENTER
RUN STOP/RES
Fuji Engineering Drive
FED S
Voltage Class
S
2
4
1.5 C 1
Mark
C
Mark
1PH 200 to 240 V
3PH 200 to 240 V
3PH 380 to 480 V
Series
Mark
0.4
0.75
1.5
2.2
Applicable Motor
(kW)
3.7
5.5
7.5
11
15
0.4
0.75
1.5
2.2
3.7
5.5
7.5
11
15
E
G
B
Mark
B Yes
Built-in Braking Unit
Null No
Compact
Heavy Duty
Multi
Version

5.
1 Product Information
- 4 -
1.2 General Speci cations
Voltage class 200 to 240VAC
Model: C1-xB(1)
0.4 0.75 1.5 2.2
Dimension(2)
Height
Width
Depth
[H ]: 180 mm
[W]: 75 mm
[D]: 145 mm
Mounting Hole, [mm] 5.0
Drive Input Rated Input voltage 1 PH, 200 to 240 VAC , -15% to +10%
Rated input current, [A] 6.5 11.0 18.0 27.0
Rated input frequency 50/60 Hz, 5%
Power capacity, [kVA] 1.7 3.0 4.8 7.1
Drive Output Applicable motor [kW] 0.4 0.75 1.5 2.2
[HP] 0.5 1 2 3
Output current, [A] 2.6 4.6 8.0 11.0
Default carrier frequency, [kHz] 6 6 6 6
Overload capacity 150% for 60 Sec
Max. output voltage 3 PH, 0 to 240 VAC
Max. output frequency 50 to 500 Hz
Braking Resistor Recommended power, [W] 80 80 100 100
Recommended resistance, min. [ ] 200 150 100 70
Weight, [kg] 1.1
Note
(1): "B" denotes build-in brake function.
(2): The dimensions are shown as below:

6.
1 Product Information
- 5 -
H
H1
W
A
B
PRG
MF.K
ENTER
RUN STOP/RES
D
1.3 Environment
Altitude Below 1000 m, 1% derating current per 100 m at 1000 to 3000 m. Max. 3000 m.
Storage Temperature -20°C to +60°C
Operating Temperature 10°C to +40°C. 1.5% derating current per 1°C at 40°C to 50°C. Max. 50°C.
Max. Humidity 95% RH, no-condensing
Vibration 5.9 g/s2
(0.6 g)
Running Environment PD2
Power Supply System TT/TN
IT (Remove the screws of VDR and EMC lter according to section 2.3.)
Enclosure IP20

7.
2 Wiring
- 6 -
2 Wiring
2.1 Typical System Connection
L1
L2
U
V
W
DI1
DI2
DI3
DI4
COM
+10V
GND
485+
485-
GND
AI
T/C
T/A
AO1
GND
L1
L2 M
AM
A
+ BR
Forward run F4-00 = 1
Forward jog F4-01 = 4
Fault reset F4-02 = 9
F4-03 = 12
1 to 5 k
0 to 10 V or
0 to 20 mA
Modbus-RTU
(max.: 115200 bps)
STP cable
External operating panel
(keypad & display)
Analog Voltage
Output: 0 to 10V
Relay output
Normally-open contact
Load: 3 A/250 AC, 3 A/30 VDC
FuseBreaker
PE
PE PE
Multi-Reference 1
DI4 supports 20 kHz pulse input.
Default value
1: OFF, 2: OFF, 3: OFF
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
Current
input
Voltage
input
Matching RS485
terminal resistor
Not matching
RS485 terminal
resistor
Voltage or current input
selected via DIP switch
(voltage input by default)
Note
For the DI terminals, low level is valid and valid level is 5 V, input resistance is 3.6 , DI1 to DI3 satis es 100 Hz frequency input, and
DI4 satis es 20 kHz frequency input. The requirement of pulse duty cycle is 30% to 70%.

8.
2 Wiring
- 7 -
2.2 Terminal Description
Terminals of Main Circuit
L1
WVU
L2 BR (+)
Terminal Terminal Name Description
L1, L2 Single-phase supply input Connect to the single-phase AC power supply.
BR, (+) Braking resistor connection Connected to external braking resistor.
U, V, W Output terminals Connect to a three-phase motor.
Ground (PE) Grounding connection.
Terminals of Main Control Board
ON
1 2 3
DI1 DI2 DI3 DI4 COM AI AO 10V GND 485+ TCTA485-
DIP switch
Default value:1: OFF, 2: OFF, 3: OFF
ON
1 2 3
ON
1 2 3
ON
1 2 3
ON
1 2 3
Current
input
Voltage
input
Matching RS485
terminal resistor
Not matching
RS485 terminal
resistor

9.
2 Wiring
- 8 -
Terminal Terminal Name Description
+10V-GND +10 VDC power supply Provides +10V power supply to an external unit.
Generally used to supply an external potentiometer of 1 to 5 k .
Max. output current: 10 mA.
AI-GND Analog input Either a voltage or a current input, determined by jumper J9;
Input voltage range: 0 to 10 VDC;
Input current range: 0 to 20 mA;
Resolution: 12 bits
Correction accuracy: 0.5%
Response time: < 8 ms
DI1-COM Digital input Low level valid;
Valid level < 5 V;
Frequency < 100 HZ
Input resistance: 4 k
DI2-COM
DI3-COM
DI4-COM High-speed pulse input High-speed pulse input, supporting a maximum of 20 kHz
Input resistance: 4 k
AO-GND Analog output 1 0 to 10 V
Correction accuracy: 100 mV
Resolution: 10 bits
Correction accuracy: 1%
T/A-T/C Normally open terminal Contact driving capacity: 250 VAC, 3 A, Cos f = 0.4, 30 VDC, 3 A.
Applies to overvoltage Category II circuit
485+ - 485- RS485 communication Half-duplex RS485 communication
Max. baud rate: 115200
Supporting a maximum of 64 nodes
2.3 Remove the EMC and VDR screws
If the drive is applied in an IT system, remove the EMC and VDR screws as shown in the following gures.
VDR Jumper
screw
EMC Jumper
screw

10.
3 Operating Panel (Keypad & Display)
- 9 -
3 Operating Panel
3.1 Get Familiar with Operating Panel
Overview
L1
WVU
10min
PRG
MF.K
ENTER
RUN REMOTE TUNE / TC/FWD REV
RUN
STOP/RE
S
LED display
Interface of external operating
panel
Status Indicators
RUN
REMOTE
FWD/REV
TUNE/TC
DIP switch
Control terminals
L2 BR (+)
ON
1 2 3
Keys
PRG
MF.K
ENTER
RUN
STOP/RES
i
DI1 DI2 DI3 DI4 COM AI AO 10V GND 485+ TCTA485-
i
Read the user manual of the AC drive
carefully before installation or operation.
10min
Do not remove the front cover while the
power is on or within10 minutes after the
power is turned off.
Keys on operation panel
Key Key Name Function
PRG
Programming Enter or exit Level I menu.
Return to the previous menu.
ENTER
Con rm Enter each level of menu interface.
Con rm displayed parameter setting.
Increment When navigating a menu, it moves the selection up through the screens available.
When editing a parameter value, it increases the displayed value.
When the AC drive is in RUN mode, it increases the speed.
Decrement When navigating a menu, it moves the selection down through the screens available.
When editing a parameter value, it decreases the displayed value.
When the AC drive is in RUNNING mode, it decreases the speed.
Shift Select the displayed parameter in the STOP or RUNNING status.
Select the digit to be modi ed when modifying a parameter value
RUN
RUN Start the AC drive when using the operating panel control mode.
It is inactive when using the terminal or communication control mode.
STOP/RES
Stop/Reset Stop the AC drive when the drive is in the RUNNING status.
Perform a reset operation when the drive is in the FAULT status.
Note: The functions of this key can be restricted by using function F7-02.
MF.K
Multifunction Perform a function switchover as de ned by the setting of F7-01, for example to quickly switch
command source or direction.

11.
3 Operating Panel (Keypad & Display)
- 10 -
Status Indicators
There are four red LED status indicators at the top of the operating panel.
Indicator Indication
RUN ON indicates the RUNNING status.
FLASHING indicates power dip ride-through.
OFF indicates the STOP status.
REMOTE ON indicates under terminal control.
FLASHING indicates under remote control.
OFF indicates under operating panel control.
FWD/REV ON indicates reverse motor rotation.
OFF indicates forward motor rotation.
TUNE/TC FLASHING indicates a fault condition on AC drive.
OFF indicates a normal condition on AC drive.
Operations of Parameters
50.00 F0 F0
F1
FP
...
A1
U0
AC
...
FP
A1
..
.
F0
F1
F0 02
F0 03
F0 26
...
F0 02
F0 26
...
1
2
0 F0 03
ENTER
PRG
PRG PRG PRG PRG
ENTER ENTER
ENTER
PRG
AC
U0
F0
...
Parameter Arrangement
Function Code Group Description Remark
F0 to FF Standard function code group Standard function parameters
A1 to AC Advanced function code group AI/AO correction
U0 RUNNING status function code group Display of basic parameters

12.
4 Quick Setup
- 11 -
4 Quick Setup
4.1 Setup Flowchart
START Para. Parameter name Default Commission
Before power on
Install and wire the drive Install and wire the drive as explained in chapters 1 to 3 of the AC
Drives User Manual.
Check wirings -
of power supply and AC drive
outputs
Restore parameters FP-01 Parameter initialization 0
0: No operation
01: Restore default settings except motor parameters
02: Clear records including errors
03: Reserved
04: Back up parameters
05 to 19: Reserved
20: Mechanical movement industry (conveying belt)
21: Inertia industry (fan)
22 to 500: Reserved
501: Restore user’s backup parameters
NOTE: It is recommended to "Restore default settings" prior to commissioning the AC
drive.
CONTINUE Para. Parameter name Default Commission

13.
4 Quick Setup
- 12 -
START Para. Parameter name Default Commission
Set motor parameters Motor Nameplate
F1-01 Rated motor power model dependent 1.5
Unit: kW
F1-02 Rated motor voltage model dependent 380
Unit: V
F1-03 Rated motor current model dependent 3.4
Unit: A
F1-04 Rated motor frequency model dependent 50
Unit: Hz
F1-05 Rated motor speed model dependent 2800
Unit: rpm.
Perform motor auto-tuning F1-37 Auto-tuning selection 0 1
0: No auto-tuning
1: Static auto-tuning
Steps of auto-tuning:
1. Ensure the UVW connection between inverter and motor is not cut off by output
contactor; if it is cut off, then manually handle with the output contactor.
2. Set F0-02 = 0 (operating panel), so that the key RUN can start the tuning procedure.
3. Set F1-37 = 1, press ENTER , then LED on panel will display letters "TUNE".
4. Press the key RUN on panel, then motor starts auto-tuning, it usually takes about 30
seconds to nish this auto-tuning, wait until LED stops displaying "TUNE"
Select command source. F0-02 Command source selection 1
0: Operating panel (keypad & display)
1: Terminal I/O control
2: Serial comms.
Select frequency reference
setting channel
F0-03 Main frequency reference setting channel
selection
0
0: Digital setting F0-08 (pressing or can revise F0-08 easily, and the revised
value won’t be cleared even after power off)
1: Digital setting F0-08 (pressing or can change F0-08 easily, but the revised
value would be cleared after power off)
2: AI
5: Pulse setting (DI4)
6: Multi-reference setting
7: Simple PLC
8: PID
9: Communication setting
CONTINUE Para. Parameter name Default Commission

14.
4 Quick Setup
- 13 -
CONTINUE Para. Parameter name Default Commission
If F0-08 is frequency reference
Set F0-08 F0-08 Preset frequency 50.00
If AI is fequency reference
0 Hz to F0-10
Set AI F4-13 AI curve minimum input 0.00
If multi-reference is frequency
reference
0 V to F4-15;
F4-14 Corresponding percentage of AI minimum
input
0.0
-100.0% to 100.0%
F4-15 AI maximum input 10.00
F4-13 to 10.00 V
F4-16 Corresponding percentage of AI maximum
input
100.0
-100.0% to 100.0%
Set multi-reference values FC-00 Reference 0 0.0
If any digital input is used
0.0% to 100.0%
FC-01 to
FC-07
Reference 1o reference 7 0.0
0.0% to 100.0%
Set DI function F4-00 DI1 function selection 1
0: No function
1: Forward run (FWD)
2: Reverser run (REV)
3: Three-wire control
4: Forward jog (FJOG)
5: Reverse jog (RJOG)
6: Terminal UP
7: Terminal DOWN
8: Coast to stop
9: Fault reset (RESET)
10: RUN disabled
11: External fault normally-open input
12: Multi-reference terminal 1
13: Multi-reference terminal 2
14: Multi-reference terminal 3
15: Multi-reference terminal 4
16: Terminal 1 for acceleration/deceleration time selection
18: Frequency reference setting channel switchover
19: UP and DOWN setting clear (terminal, operation panel)
20: Command source switchover
21: Acceleration/Deceleration prohibited
22: PID disabled
23: PLC state reset
CONTINUE Para. Parameter name Default Commission

15.
4 Quick Setup
- 14 -
CONTINUE Para. Parameter name Default Commission
F4-00 DI1 function selection 1
30: Pulse input as frequency reference (valid only for DI4)
32: Immediate DC injection braking
33: External fault normally-closed input
34: Frequency modi cation enabled
35: PID operation direction reverse
36: External stop 1
37: Command source switchover 2
38: PID integral disabled
39: Switchover between main frequency reference and preset frequency
40: Switchover between auxiliary frequency reference and preset frequency
43: PID parameter switchover
47: Emergency stop (ES)
48: External stop 2
49: Deceleration DC injection braking
50: Clear running time this time
51: Two-wire control/ Three-wire control
52: Reverse running prohibited
F4-01 DI2 function selection 4
Setting range same as DI1.
F4-02 DI3 function selection 9
Setting range same as DI1.
F4-03 DI4 function selection 12
If any digital output is used Setting range same as DI1.
Set DO function F5-02 Relay function selection(T/A-T/C) 0
0: No output
1: AC drive running
2: Fault output
3: Frequency level detection 1 output
4: Frequency reached
5: Zero-speed running (no output at stop)
6: Motor overload pending
7: AC drive overload pending
11: PLC cycle completed
12: Accumulative running time reached
13: Frequency limited
15: Ready for RUN
17: Frequency upper limit reached
18: Frequency lower limit reached (no output at stop)
19: Undervoltage
20: Communication setting
24: Accumulative power-on time reached
26: Frequency 1 reached
28: Current 1 reached
30: Timing reached
CONTINUE Para. Parameter name Default Commission

16.
4 Quick Setup
- 15 -
CONTINUE Para. Parameter name Default Commission
Set DO function F5-02 Relay function selection(T/A-T/C) 0
If an analog output is used
31: AI input exceeding limit
32: Load lost
33: Reverse running
34: Zero current
36: Output current exceeding limit
37: Frequency lower limit reached (having output at stop)
38: Alarm output
40: Current running time reached
41: Fault output
Set AO function F5-07 AO function selection 0
0: Running frequency
1: Set frequency
2: Output current
3: Output torque
4: Output power
5: Output voltage
6: Pulse input (100% corresponding to 20 kHz)
7: AI
12: Communication setting
13: Motor rotational speed
14: Output current (100% corresponding to 100 A)
15: Output voltage (100% corresponding to 1000 V)
Set accel. /decel. time F0-17 Acceleration time 1 Model dependent
If smooth accel./decel. is
requested
0.0s to 6500.0s
F0-18 Deceleration time 1 Model dependent
0.0s to 6500.0s
Set S-curve F6-07 Acceleration/Deceleration mode 0
0: Linear acceleration/deceleration
1: Static S-curve acceleration/deceleration
2: Dynamic S-curve acceleration/deceleration
F6-08 Time proportion of S-curve at Accel. start 30.0
0.0% to (100.0% - F6-09)
F6-09 Time proportion of S-curve at Accel. end 30.0
0.0% to (100.0% - F6-08)
CONTINUE Para. Parameter name Default Commission

17.
4 Quick Setup
- 16 -
CONTINUE Para. Parameter name Default Commission
Set VF parameters F3-00 V/F curve selection 0
0: Linear V/F
1: Multi-point V/F
F3-01 Torque boost 0.0
0.0 to 30.0 %;
NOTE: if it is 0, then auto torque boost is activated, and it is recommended to use
auto torque boost.
F3-02 Frequency limit of torque boost 50.00
0.00 Hz to maximum output frequency
F3-03 Multi-point V/F frequency 1 0.00
0.00 Hz to F3-05
F3-04 Multi-point V/F voltage 1 0.0
0.0 to 100.0 V
F3-05 Multi-point V/F frequency 2 0.00
F3-03 to F3-07, Hz
F3-06 Multi-point V/F voltage 2 0.0
0.0 to 100.0 V
F3-07 Multi-point V/F frequency 3 0.00
F3-05 to rated motor frequency F1-04, Hz
F3-08 Multi-point V/F voltage 3 0.0
0.0 to 100.0 V
Trial RUN Use operating panel, or digital input terminal, or serial communication control, to
start inverter, check if the running performance satis es your application. If yes,
then go forward to next step, if NO, then go back to check.
Finish

18.
5 Parameter Table
- 17 -
5. Parameter Table
5.1 Introduction
Groups F and A include standard function parameters. Group U includes the monitoring function parameters and extension card
communication parameters.
5.2 Standard Parameters
Para. No. Para. Name Setting Range Default Comms. Address
Group F0: Standard Parameters
F0-02 Command source selection 0: Operating panel
1: Terminal I/O control
2: Serial comms.
0 0xF002/0x0002
F0-03 Main frequency reference setting
channel selection
0: Digital setting (non-retentive at power down)
1: Digital setting (retentive at power down)
2: AI
5: Pulse reference(DI4)
6: Multi-reference
7: Simple PLC
8: PID reference
9: Serial comms.
0 0xF003/0x0003
F0-04 Auxiliary frequency reference
setting channel selection
Same with F0-03 0 0xF004/0x0004
F0-05 Base value of range of auxiliary
frequency reference for main and
auxiliary calculation
0: Relative to maximum frequency
1: Relative to main frequency reference
0 0xF005/0x0005
F0-06 Range of auxiliary frequency
reference for main and auxiliary
calculation
0% to 150% 100% 0xF006/0x0006
F0-07 Final Frequency reference setting
selection
00 to 34 00 0xF007/0x0007
F0-08 Preset frequency 0.00 to max. frequency (F0-10) 50.00 Hz 0xF008/0x0008
F0-09 Running direction 0: Run in the default direction
1: Run in the direction reverse to the default
direction
0 0xF009/0x0009
F0-10 Max. frequency 50.00 to 500.00 Hz 50.00 Hz 0xF00A/0x000A
F0-11 Setting channel of frequency
upper limit
0: Set by F0-12
1: AI
4: Pulse reference (DI4)
5: Communication reference
0 0xF00B/0x000B
F0-12 Frequency reference upper limit F0-14 to F0-10 50.00 Hz 0xF00C/0x000C
F0-14 Frequency reference lower limit 0.00 Hz to frequency upper limit (F0-12) 0.00 Hz 0xF00E/0x000E
F0-15 Carrier frequency 0.8 to 11 kHz Model
dependent
0xF00F/0x000F
F0-16 Carrier frequency adjusted with
temperature
0: Disabled
1: Enabled
1 0xF010/0x0010
F0-17 Accelerationtime1 0.0s to 6500.0s Model
dependent
0xF011/0x0011
F0-18 Decelerationtime1 0.0s to 6500.0s Model
dependent
0xF012/0x0012
F0-23 Retentive of digital setting
frequency upon stop
0: Not retentive
1: Retentive
0 0xF017/0x0017

19.
5 Parameter Table
- 18 -
Para. No. Para. Name Setting Range Default Comms. Address
F0-25 Acceleration/Deceleration time
base frequency
0: Maximum frequency (F0-10)
1: Frequency reference
2: 100 Hz
0 0xF019/0x0019
F0-26 Base frequency for UP/DOWN
modi cation during running
0: Running frequency
1: Frequency Reference
0 0xF01A/0x001A
Group F1: Motor 1 Parameters
F1-01 Rated motor power 0.1 to 3.7 kW Model
dependent
0xF101/0x0101
F1-02 Rated motor voltage 1 to 600 V Model
dependent
0xF102/0x0102
F1-03 Rated motor current 0.01 to 15 A Model
dependent
0xF103/0x0103
F1-04 Rated motor frequency 0.01 Hz to max. frequency Model
dependent
0xF104/0x0104
F1-05 Rated motor speed 1 to 65535 rpm Model
dependent
0xF105/0x0105
F1-06 Stator resistance 0.001 to 65.535 Auto-tuning
dependent
0xF106/0x0106
F1-37 Motor auto-tuning method
selection
0: No auto-tuning
1: Static auto-tuning 1
0 0xF125/0x0125
GroupF3: V/F Control Parameters
F3-00 V/F curve setting 0: Linear V/F
1: Multi-point V/F
0 0xF305/0x0305
F3-01 Torque boost 0.0%: automatic boost
0.1% to 30%
Model
dependent
0xF301/0x0301
F3-02 Cut-off frequency of torque boost 0.00 Hz to max. frequency 50.00Hz 0xF302/0x0302
F3-03 Multi-point V/F frequency 1 0.00 Hz to F3-05 0.00 Hz 0xF303/0x0303
F3-04 Multi-point V/F voltage 1 0.0% to 100.0% 0.0% 0xF304/0x0304
F3-05 Multi-point V/F frequency 2 F3-03 to F3-07 0.00Hz 0xF305/0x0305
F3-06 Multi-point V/F voltage 2 0.0% to 100.0% 0.0% 0xF306/0x0306
F3-07 Multi-point V/F frequency 3 F3-05 to rated motor frequency(F1-04) 0.00 Hz 0xF307/0x0307
F3-08 Multi-point V/F voltage 3 0.0% to 100.0% 0.0% 0xF308/0x0308
F3-09 Slip compensation gain 0.0% to 200.0% 0.0% 0xF309/0x0309
F3-10 V/F over-excitation gain 0 to 200 64 0xF30A/0x030A
F3-18 Current limit level 50% to 200% 150% 0xF312/0x0312
F3-19 Current limit selection 0: Disabled
1: Enabled
1 0xF313/0x0313
F3-20 Current limit gain 0 to 100 20 0xF314/0x0314
F3-21 Compensation factor of speed
multiplying current limit level
0 to 200% 50% 0xF315/0x0315
F3-22 Voltage limit 330 to 390 V 390 V 0xF316/0x0316
F3-23 Voltage limit selection 0: Disabled
1: Enabled
1 0xF318/0x0317
F3-24 Frequency gain for voltage limit 0 to 100 30 0xF318/0x0318
F3-25 Voltage gain for voltage limit 0 to 100 30 0xF319/0x0319
F3-26 Frequency rise threshold during
voltage limit
0 to 50 Hz 5Hz 0xF31A/0x031A

20.
5 Parameter Table
- 19 -
Para. No. Para. Name Setting Range Default Comms. Address
Group F4: Input Terminals
F4-00 DI1 function selection 0: No function
1: Forward run (FWD)
2: Reverser run (REV)
3: Three-wire control
4: Forward jog (FJOG)
5: Reverse jog (RJOG)
6: Terminal UP
7: Terminal DOWN
8: Coast to stop
9: Fault reset (RESET)
10: RUN disabled
11: External fault normally-open input
12: Multi-reference terminal 1
13: Multi-reference terminal 2
14: Multi-reference terminal 3
15: Multi-reference terminal 4
16: Terminal 1 for acceleration/deceleration time
selection
18: Frequency reference setting channel
switchover
19: UP and DOWN setting clear (terminal,
operation panel)
20: Command source switchover
21: Acceleration/Deceleration prohibited
22: PID disabled
23: PLC state reset
30: Pulse input as frequency reference (valid
only for DI4)
32: Immediate DC injection braking
33: External fault normally-closed input
34: Frequency modi cation enabled
35: PID operation direction reverse
36: External stop 1
37: Command source switchover 2
38: PID integral disabled
39: Switchover between main frequency
reference and preset frequency
40: Switchover between auxiliary frequency
reference and preset frequency
43: PID parameter switchover
47: Emergency stop (ES)
48: External stop 2
49: Deceleration DC injection braking
50: Clear running time this time
51: Two-wire control/ Three-wire control
52: Reverse running prohibited
1 0xF400/0x0400
F4-01 DI2 function selection 4 0xF401/0x0401
F4-02 DI3 function selection 9 0xF402/0x0402
F4-03 DI4 function selection 12 0xF403/0x0403
F4-10 DI lter time 0.000s to 1.000s 0.010s 0xF40A/0x040A
F4-11 Terminal I/O control mode 0: Two-wire control mode 1
1: Two-wire control mode 2
2: Three-wire control mode 1
3: Three-wire control mode 2
0 0xF40B/0x040B
F4-12 Terminal UP/DOWN rate 0.001 to 65.535 Hz/s 1.000 Hz/s 0xF40C/0x040C

21.
5 Parameter Table
- 20 -
Para. No. Para. Name Setting Range Default Comms. Address
F4-13 AI curve1 min. input 0.00 V to F4-15 0.00 V 0xF40D/0x040D
F4-14 Corresponding percentage of AI
curve 1 min. input
-100.00% to 100.0% 0.0% 0xF40E/0x040E
F4-15 AI curve 1 max. input F4-13 to 10.00 V 10.00 V 0xF40F/0x040F
F4-16 Corresponding percentage of
AIcurve1 max. input
-100.00% to 100.0% 100.0% 0xF410/0x0410
F4-17 AI1 ltertime 0.00s to 10.00s 0.10s 0xF411/0x0411
F4-28 Pulse min. input 0.00 kHz to F4-30 0.00 kHz 0xF41C/0x041C
F4-29 Corresponding percentage of
pulse min. input
-100.00% to 100.0% 0.0% 0xF41D/0x041D
F4-30 Pulse max. input F4-28 to 20.00 kHz 50.00 kHz 0xF41E/0x041E
F4-31 Corresponding percentage of
pulse max. input
-100.00% to 100.0% 100.0% 0xF41F/0x041F
F4-32 Pulse lter time 0.00s to 10.00s 0.10s 0xF420/0x0420
F4-38 DI active mode selection1 00000 to 11111 00000 0xF426/0x0426
Group F5: Output Terminals
F5-02 Relay (T/A-T/B-T/C) function
selection
0: No output
1: AC drive running
2: Fault output
3: Frequency level detection 1 output
4: Frequency reached
5: Zero-speed running (no output at stop)
6: Motor overload pending
7: AC drive overload pending
11: PLC cycle completed
12: Accumulative running time reached
13: Frequency limited
15: Ready for RUN
17: Frequency upper limit reached
18: Frequency lower limit reached (no output at
stop)
19: Undervoltage
20: Communication setting
24: Accumulative power-on time reached
26: Frequency 1 reached
28: Current 1 reached
30: Timing reached
31: AI input exceeding limit
32: Load lost
33: Reverse running
34: Zero current
36: Output current exceeding limit
37: Frequency lower limit reached (having output
at stop)
38: Alarm output
40: Current running time reached
41: Fault output
2 0xF502/0x0502
F5-02 Relay (T/A-T/B-T/C) function
selection
2 0xF502/0x0502

22.
5 Parameter Table
- 21 -
Para. No. Para. Name Setting Range Default Comms. Address
F5-07 AO1functionselection 0: Running frequency
1: Frequency reference
2: Output current
3: Output torque
4: Output power
5: Output voltage
6: Pulse input
7: AI
12: Communication reference
13: Motor speed
14: Output current
15: Output voltage
0 0xF507/0x0507
F5-10 AO zero offset coef cient -100.0% to 100.0% 0.0% 0xF50A/0x050A
F5-11 AO gain -10.00 to 10.00 1.00 0xF50B/0x050B
F5-18 Relay1outputdelay 0.0s to 3600.0s 0.0s 0xF512/0x0512
F5-22 DO active mode selection 1 00000 to 11111 00000 0xF516/0x0516
Group F6: Start/Stop Control
F6-00 Start mode 0:Direct start
1:Catching a spinning motor
0 0xF600/0x0600
F6-01 Mode of catching a spinning
motor
0: From stop frequency
1: From zero speed
2: From max. frequency
4: Catching a spinning motor in eld-orientated
control (requiring static auto-tuning, F1-37 = 1)
4 0xF601/0x0601
F6-03 Start frequency 0.00to10.00Hz 0.00 Hz 0xF603/0x0603
F6-04 Start frequency holding time 0.0s to 100.0s 0.0s 0xF604/0x0604
F6-07 Acceleration/Deceleration mode 0: Linear acceleration/deceleration
1: Static S-curve acceleration/deceleration
2: Dynamic S-curve acceleration/deceleration
0 0xF607/0x0607
F6-08 Time proportion of S-curve start
segment
0.0% to (100.0% –F6-09) 30.0% 0xF608/0x0608
F6-09 Time proportion of S-curve end
segment
0.0% to (100.0% –F6-08) 30.0% 0xF609/0x0609
F6-10 Stop mode 0:Decelerate to stop
1:Coast to stop
0 0xF60A/0x060A
F6-11 DC injection braking 2 start
frequency
0.00 Hz to maximum frequency 0.00 Hz 0xF60B/0x060B
F6-12 DC injection braking 2 delay time 0.0 to 100.0s 0.0s 0xF60C/0x060C
F6-13 DC injection braking 2 level 0% to 100% 50% 0xF60D/0x060D
F6-14 DC injection braking 2 active time 0.0s to 100.0s 0.0s 0xF60E/0x060E
F6-21 Demagnetization time 0.00s to 5.00s 0.5s 0xF615/0x0615
F6-22 Min. output frequency 0.00 Hz to F6-11 0.00 Hz 0xF616/0x0616

23.
5 Parameter Table
- 22 -
Para. No. Para. Name Setting Range Default Comms. Address
Group F7: Keypad Operation and LED Display
F7-00 LED default display check 0: Disabled
1: Enabled
0 0xF700/0x0700
F7-01 MF.K key function selection 0: MF.K key disabled
1: Switchover from remote control (terminal or
communication) to keypad control
2: Switchover between forward rotation and
reverse rotation
3: Forward jog
4: Reverse jog
5: Parameter display mode switchover
0 0xF701/0x0701
F7-06 Load speed display coef cient 0.0001 to 6.5000 1.0000 0xF706/0x0706
F7-07 Heatsink temperature of IGBT 0°C to 100°C - 0xF707/0x0707
F7-08 Product series 200 - 0xF708/0x0708
F7-09 Accumulative running time 0 to 65535h - 0xF709/0x0709
F7-10 Performance software version - - 0xF70A/0x070A
F7-11 Function software version - - 0xF70B/0x070B
F7-12 Number of decimal places for
load speed display
10 to 23 21 0xF70C/0x070C
F7-13 Accumulative power-on time 0 to 65535 h - 0xF70D/0x070D
F7-14 Accumulative power consumption 0 to 65535 kWh - 0xF70E/0x070E
Group F8: Auxiliary Functions
F8-00 Jog frequency reference 0.00 Hz to max. frequency 2.00Hz 0xF800/0x0800
F8-01 Jog acceleration time 0.0s to 6500.0s 20.0s 0xF801/0x0801
F8-02 Jog deceleration time 0.0s to 6500.0s 20.0s 0xF802/0x0802
F8-03 Acceleration time 2 0.0s to 6500.0s Model
dependent
0xF803/0x0803
F8-04 Deceleration time 2 0.0s to 6500.0s Model
dependent
0xF804/0x0804
F8-12 Forward/Reverse run switchover
dead-zone time
0.0s to 3000.0s 0.0s 0xF80C/0x080C
F8-13 Reverse RUN selection 0: Disabled
1: Enabled
0 0xF80D/0x080D
F8-14 Running mode when frequency
reference lower than frequency
lower limit
0: Run at frequency reference lower limit
1: Stop
2: Run at zero speed
0 0xF80E/0x080E
F8-16 Accumulative power-on time
threshold
0 to 65000 h 0h 0xF810/0x0810
F8-17 Accumulative running time
threshold
0 to 65000 h 0h 0xF811/0x0811
F8-18 Startup protection selection 0: Disabled
1: Enabled
0 0xF812/0x0812
F8-19 Frequency detection value 1 0.00 Hz to max. frequency 50.00 Hz 0xF813/0x0813
F8-20 Frequency detection hysteresis 1 0.0% to 100.0% 5.0% 0xF814/0x0814
F8-21 Detection width of target
frequency reached
0.0% to 100.0% 0.0% 0xF815/0x0815
F8-25 Switchover frequency of accel.
time 1 and accel. time 2
0.00 Hz to max. frequency 0.00 Hz 0xF819/0x0819

24.
5 Parameter Table
- 23 -
Para. No. Para. Name Setting Range Default Comms. Address
F8-26 Switchover frequency of decel.
time 1 and decel. time 2
0.00 Hz to max. frequency 0.00 Hz 0xF81A/0x081A
F8-27 Set highest priority to terminal
JOG function
0: Disabled
1: Enabled
0 0xF81B/0x081B
F8-30 Detection of frequency1 0.00 Hz to max. frequency 50.00 Hz 0xF81E/0x081E
F8-31 Detection width of frequency1 0.0% to 100.0% (max. frequency) 0.0% 0xF81F/0x081F
F8-34 Zero current detection level 0.0% to 300.0% (rated motor current) 5.0% 0xF822/0x0822
F8-35 Zero current detection delay 0.01s to 600.00s 0.10s 0xF823/0x0823
F8-36 Output overcurrent threshold 0.0% (no detection)
0.1% to 300.0% (rated motor current)
200.0% 0xF824/0x0824
F8-37 Output overcurrent detection
delay
0.00s to 600.00s 0.00s 0xF825/0x0825
F8-38 Detection level of current1 0.0% to 300.0% (rated motor current) 100.0% 0xF826/0x0826
F8-39 Detection width of current1 0.0% to 300.0% (rated motor current) 0.0% 0xF827/0x0827
F8-42 Timing function 0: Disabled
1: Enabled
0 0xF82A/0x082A
F8-43 Running time setting channel 0: Set by F8-44
1: AI
0 0xF82B/0x082B
F8-44 Running time 0.0 to 6500.0 min 0.0 min 0xF82C/0x082C
F8-45 AI input voltage lower limit 0.00 V to F8-46 3.10 V 0xF82D/0x082D
F8-46 AI input voltage upper limit F8-45 to 10.00 V 6.80 V 0xF82E/0x082E
F8-53 Running time threshold this time 0.0 to 6500.0 min 0.0 min 0xF835/0x0835
F8-54 Output power correction
coef cient
0.0% to 200.0% 100.0% 0xF836/0x0836
F8-55 Emergency deceleration time 0.0s to 6500.0s 0.1s 0xF837/0x0837
F8-57 Speed synchronous control
selection
0: Disabled
1: Enabled
0 0xF839/0x0839
It selects whether to enable the speed synchronous control function.
This function means direction data communication between two or more AC drives via CANlink, implementing target frequency of one
or more slaves to be synchronized to that of the master.
When this function is enabled, CANlink communication addresses of the master and slaves are matched automatically. The baud rate
in speed synchronous control is set in Fd-00.
F8-58 Master and slave selection in
synchronous control
0: Master
1: Slave
0 0xF83A/0x083A
It is used to select whether the AC drive is master or slave. When the AC drive is slave, set F0-03 = 9 to set frequency reference via
communication.
Group F9: Fault and Protection
F9-00 Motor overload protection 0: Disabled
1: Enabled
1 0xF900/0x0900
F9-01 Motor overload protection gain 0.20 to 10.00 0.20 0xF901/0x0901
F9-02 Motor overload pre-warning
coef cient
50% to 100% 80% 0xF902/0x0902
F9-07 Detection of short-circuit to
ground upon power-on
0: Disabled
1: Enabled
1 0xF907/0x0907
F9-08 Braking unit applied voltage 310 to 400 V 378 V 0xF908/0x0908
F9-09 Auto reset times 0 to 20 0 0xF909/0x0909

25.
5 Parameter Table
- 24 -
Para. No. Para. Name Setting Range Default Comms. Address
F9-10 Selection of DO action during
auto reset
0: Not act
1: Act
0 0xF90A/0x090A
F9-11 Delay of auto reset 0.1s to 100.0s 1.0s 0xF90B/0x090B
F9-13 Output phase loss protection 0: Disabled
1: Enabled
1 0xF90D/0x090D
F9-14 1st fault type 0: No fault
1: Reserved
2: Overcurrent during acceleration
3: Overcurrent during deceleration
4: Overcurrent at constant speed
5: Overvoltage during acceleration
6: Overvoltage during deceleration
7: Overvoltage at constant speed
8: Pre-charge resistor overloaded
9: Undervoltage
10: AC drive overloaded
11: Motor overloaded
12: Input phase loss
13: Output phase loss
14: IGBT overheat
15: External fault
16: Communication abnormal
17: Reserved
18: Current detection abnormal
19: Motor auto-tuning abnormal
20: Reserved
21: Parameter read-write abnormal
22: Reserved
23: Motor short circuited to ground
24: Reserved
25: Reserved
26: Accumulative running time reached
29: Accumulative power-on time reached
30: Load lost
31: PID feedback lost during running
40: Overcurrent fast prevention timeout
41: Reserved
42: Reserved
43: Reserved
45: Reserved
51: Reserved
55: Slave fault in speed synchronous
- 0xF90E/0x090E
F9-15 2nd fault type - 0xF90F/0x090F
F9-16 3rd (latest) fault type - 0xF910/0x0910
F9-17 Frequency upon 3rd fault - - 0xF911/0x0911
F9-18 Current upon 3rd fault - - 0xF912/0x0912
F9-19 Bus voltage upon 3rd fault - - 0xF913/0x0913
F9-20 DI state upon 3rd fault - - 0xF914/0x0914
F9-21 DO state upon 3rd fault - - 0xF915/0x0915
F9-22 AC drive state upon 3rd fault - - 0xF916/0x0916
F9-23 Power-on time upon 3rdfault - - 0xF917/0x0917
F9-24 Running time upon 3rd fault - - 0xF918/0x0918

26.
5 Parameter Table
- 25 -
Para. No. Para. Name Setting Range Default Comms. Address
F9-27 Frequency upon 2nd fault - - 0xF91B/0x081B
F9-28 Current upon 2nd fault - - 0xF91C/0x091C
F9-29 Bus voltage upon 2nd fault - - 0xF91D/0x091D
F9-30 DI state upon 2nd fault - - 0xF91E/0x091E
F9-31 DO state upon 2nd fault - - 0xF91F/0x091F
F9-32 AC drive state upon 2nd fault - - 0xF920/0x0920
F9-33 Power-on time upon 2nd fault - - 0xF921/0x0921
F9-34 Running time upon 2nd fault - - 0xF922/0x0922
F9-37 Frequency upon 1st fault - - 0xF925/0x0925
F9-38 Current upon 1st fault - - 0xF926/0x0926
F9-39 Bus voltage upon1st fault - - 0xF927/0x0927
F9-40 DI state upon 1st fault - - 0xF928/0x0928
F9-41 DO state upon 1st fault - - 0xF929/0x0929
F9-42 AC drive state upon 1st fault - - 0xF92A/0x092A
F9-43 Power-on time upon 1st fault - - 0xF92B/0x092B
F9-44 Running time upon 1st fault - - 0xF92C/0x092C
F9-47 Fault protection action selection 1 00000 to 22222 00000 0xF92F/0x092F
F9-48 Fault protection action selection 2 00000 to 11111 00000 0xF930/0x0930
F9-49 Fault protection action selection 3 00000 to 22222 00000 0xF931/0x0931
F9-54 Frequency selection for
continuing to run upon fault
0: Current running frequency
1: Frequency reference
2: Frequency upper limit
3: Frequency lower limit
4: Backup frequency upon abnormality
0 0xF936/0x0936
F9-55 Backup frequency upon fault 0.0% to 100.0% (max. frequency) 100.0% 0xF937/0x0937
F9-59 Power dip ride-through function
selection
0: Disabled
1: Bus voltage constant control
2: Decelerate to stop
0 0xF93B/0x093B
F9-60 Threshold of power dip ride-
through function disabled
80% to F9-60 85% 0xF93C/0x093C
F9-61 Judging time of bus voltage
recovering from power dip
0.0s to 100.0s 0.5s 0xF93D/0x093D
F9-62 Threshold of power dip ride-
through function enabled
60% to 100% 80% 0xF93E/0x093E
F9-63 Load lost protection 0: Disabled
1: Enabled
0 0xF93F/0x093F
F9-64 Load lost detection level 0.0% to 100.0% 10.0% 0xF940/0x0940
F9-65 Load lost detection time 0.0s to 60.0s 1.0s 0xF941/0x0941
F9-71 Power dip ride-through gain Kp 0 to 100 40 0xF947/0x0947
F9-72 Power dip ride-through integral
coef cient
0 to 100 30 0xF948/0x0948
F9-73 Deceleration time of power dip
ride-through
0.0s to 300.0s 20.0s 0xF949/0x0949
F9-74 Restart mode after fault reset 0: Normal
1: Catching a spinning motor
0 0xF94A/0x094A

27.
5 Parameter Table
- 26 -
Para. No. Para. Name Setting Range Default Comms. Address
Group FA: PID Function
FA-00 PID reference setting channel 0: Set by FA-01
1: AI
4: Pulse reference (DI4)
5: Via communication
6: Multi-reference
0 0xFA00/0x0A00
FA-01 PID digital setting 0.0% to 100.0% 50.0% 0xFA01/0x0A01
FA-02 PID feedback setting channel 0: AI
4: PULSE reference (DI4)
5: Via communication
0 0xFA02/0x0A02
FA-03 PID operation direction 0: Forward
1: Reverse
0 0xFA03/0x0A03
FA-04 PID reference and feedback
range
0 to 65535 1000 0xFA04/0x0A04
FA-05 ProportionalgainKp1 0.0 to 1000.0 20.0 0xFA05/0x0A05
FA-06 Integral timeTi1 0.01s to 10.00s 2.00s 0xFA06/0x0A06
FA-07 DifferentialtimeTd1 0.000s to 10.000s 0.000s 0xFA07/0x0A07
FA-08 PID output limit in reverse
direction
0.00 Hz to max. frequency 0.00Hz 0xFA08/0x0A08
FA-09 PID error limit 0.0% to 100.0% 0.0% 0xFA09/0x0A09
FA-10 PID differential limit 0.00% to 100.00% 0.10% 0xFA0A/0x0A0A
FA-11 PID reference change time 0.00s to 650.00s 0.00s 0xFA0B/0x0A0B
FA-12 PID feedback lter time 0.00s to 60.00s 0.00s 0xFA0C/0x0A0C
FA-13 PID output lter time 0.00s to 60.00s 0.00s 0xFA0D/0x0A0D
FA-15 Proportional gain Kp2 0.0 to 1000.0 20.0 0xFA0F/0x0A0F
FA-16 Integral time Ti2 0.01s to 10.00s 2.00s 0xFA10/0x0A10
FA-17 Differential time Td2 0.000s to 10.000s 0.000s 0xFA11/0x0A11
FA-18 PID parameter switchover
condition
0: Not switched over
1: Switched over via DI
2: Switched over automatically according to error
3: Switched over automatically according to
running frequency
0 0xFA12/0x0A12
FA-19 PID error 1 for auto switchover 0.0% to FA-20 20.0% 0xFA13/0x0A13
FA-20 PID error 2 for auto switchover FA-19 to 100.0% 80.0% 0xFA14/0x0A14
FA-21 PID initial value 0.0% to 100.0% 0.0% 0xFA15/0x0A15
FA-22 PID initial value active time 0.00s to 650.00s 0.00s 0xFA16/0x0A16
FA-23 Max. value of two outputs error in
forward direction
0.00% to 100.00% 1.00% 0xFA17/0x0A17
FA-24 Max. value of two outputs error in
reverse direction
0.00% to 100.00% 1.00% 0xFA18/0x0A18
FA-25 PID integral property 00 to 11 00 0xFA19/0x0A19
FA-26 Detection level of PID feedback
loss
0%: No detection
0.1% to 100.0%
0.0% 0xFA1A/0x0A1A
FA-27 Detection time of PID feedback
loss
0.0s to 20.0s 0.0s 0xFA1B/0x0A1B
FA-28 Selection of PID operation at stop 0: Disabled
1: Enabled
0 0xFA1C/0x0A1C

28.
5 Parameter Table
- 27 -
Para. No. Para. Name Setting Range Default Comms. Address
Group FC: Multi-Reference and Simple PLC Function
FC-00 Reference0 -100.0% to 100.0% 0.0% 0xFC00/0x0C00
FC-01 Reference1 -100.0% to 100.0% 0.0% 0xFC01/0x0C01
FC-02 Reference2 -100.0% to 100.0% 0.0% 0xFC02/0x0C02
FC-03 Reference3 -100.0% to 100.0% 0.0% 0xFC03/0x0C03
FC-04 Reference4 -100.0% to 100.0% 0.0% 0xFC04/0x0C04
FC-05 Reference5 -100.0% to 100.0% 0.0% 0xFC05/0x0C05
FC-06 Reference6 -100.0% to 100.0% 0.0% 0xFC06/0x0C06
FC-07 Reference7 -100.0% to 100.0% 0.0% 0xFC07/0x0C07
FC-16 Simple PLC running mode 0: Stop after running one cycle
1: Keep nal values after running one cycle
2: Repeat after running one cycle
0 0xFC10/0x0C10
FC-17 Simple PLC retentive selection
0: Not retentive
1: Retentive
Retentive selection at stop
0: Not retentive
1: Retentive
Retentive selection at
power down
00 0xFC11/0x0C11
FC-18 Running time of simple PLC
reference 0
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC12/0x0C12
FC-19 Acceleration/deceleration time of
simple PLC reference 0
0 to 1 0 0xFC13/0x0C13
FC-20 Running time of simple PLC
reference1
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC14/0x0C14
FC-21 Acceleration/deceleration time of
simple PLC reference 1
0 to 1 0 0xFC15/0x0C15
FC-22 Running time of simple PLC
reference 2
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC16/0x0C16
FC-23 Acceleration/deceleration time of
simple PLC reference 2
0 to 1 0 0xFC17/0x0C17
FC-24 Running time of simple PLC
reference 3
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC18/0x0C18
FC-25 Acceleration/deceleration time of
simple PLC reference 3
0 to 1 0 0xFC19/0x0C19
FC-26 Running time of simple PLC
reference 4
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC1A/0x0C1A
FC-27 Acceleration/deceleration time of
simple PLC reference 4
0 to 1 0 0xFC1B/0x0C1B
FC-28 Running time of simple PLC
reference 5
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC1C/0x0C1C
FC-29 Acceleration/deceleration time of
simple PLC reference 5
0 to1 0 0xFC1D/0x0C1D
FC-30 Running time of simple PLC
reference 6
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC1E/0x0C1E
FC-31 Acceleration/deceleration time of
simple PLC reference 6
0 to 1 0 0xFC1F/0x0C1F
FC-32 Running time of simple PLC
reference 7
0.0s (h) to 6500.0s (h) 0.0s (h) 0xFC20/0x0C20

29.
5 Parameter Table
- 28 -
Para. No. Para. Name Setting Range Default Comms. Address
FC-33 Acceleration/deceleration time of
simple PLC reference 7
0 to 1 0 0xFC21/0x0C21
FC-50 Time unit of simple PLC running 0: s
1: h
0 0xFC32/0x0C32
FC-51 Reference 0 source 0: Set by FC-00
1: AI
4: PULSE reference
5: PID
6: Set by F0-08 and modi ed via UP/DOWN
0 0xFC33/0x0C33
Group Fd: Communication
Fd-00 Baud rate 0000 to 5009 5005 0xFD00/0x0D00
Fd-01 Data format symbol 0: No check (8-N-2)
1: Even parity check (8-E-1)
2: Odd parity check (8-O-1)
3: No check (8-N-1) (Valid for Modbus)
0 0xFD01/0x0D01
Fd-02 Local address 0: Broadcast address
1 to 247
1 0xFD02/0x0D02
Fd-03 Response delay 0 to 20ms 2 0xFD03/0x0D03
Fd-04 Communication timeout 0.0: invalid
0.1s to 60.0s
0.0s 0xFD04/0x0D04
Fd-05 Modbus protocol selection and
PROFIBUS-DP data frame
0: Non-standard Modbus protocol
1: Standard Modbus protocol
1 0xFD05/0x0D05
Fd-07 PC software selection 0: Disabled
1: Enabled
1 0xFD07/0x0D07
Group FF: Manufacturer Parameters, Access Denied
Group FP: Function Parameter Management
FP-00 User password 0 to 65535 0 0x1F00
FP-01 Industry macro 0: No operation
01: Restore factory parameters except motor
parameters
02: Clear records
03: Reserved
04: Back up current user parameters
05 to 19: Reserved
20: Mechanical movement industry (conveying
belt)
21: Inertia industry (fan)
22 to 500: Reserved
501: Restore user backup parameters
0 0x1F01
FP-02 Parameter display property
Group A display selection
0: Not displayed
1: Displayed
Group U display selection
0: Not displayed
1: Displayed
11 0x1F02
FP-04 Parameter modi cation property 0: Modi able
1: Unmodi able
0 0x1F04

30.
5 Parameter Table
- 29 -
Para. No. Para. Name Setting Range Default Comms. Address
Group A1: Virtual DI/DO
A1-07 Function selection for AI used as
DI
Same as F4-00 0 0xA107/0x4107
A1-10 Active state selection for AI used
as DI
AI
0: High level valid
1: Low level valid
0 0xA10A/0x410A
GroupA5: Control Optimization
A5-00 DPWM switchover frequency
upper limit
5.00 Hz to max. frequency 8.00Hz 0xA500/0x4500
A5-03 Random PWM depth 0 to 10 0 0xA503/0x4503
A5-04 Overcurrent fast prevention 0: Disabled
1: Enabled
1 0xA504/0x4504
A5-05 Max. output voltage coef cient 100% to 110% 103% 0xA505/0x4505
A5-06 Undervoltage threshold 140 to 280 V 200V 0xA600/0x4600
Group AC: AI/AO Correction
AC-00 AI measured voltage 1 -10.00 to 10.000 V Factory-
corrected
0xAC00/0x4C00
AC-01 AI displayed voltage 1 -10.00 to 10.000 V Factory-
corrected
0xAC01/0x4C01
AC-02 AI measured voltage 2 -10.00 to 10.000 V Factory-
corrected
0xAC02/0x4C02
AC-03 AI displayed voltage 2 -10.00 to 10.000 V Factory-
corrected
0xAC03/0x4C03
AC-12 AO target voltage 1 -10.00 to 10.000 V Factory-
corrected
0xAC0C/0x4C0C
AC-13 AO measured voltage 1 -10.00 to 10.000 V Factory-
corrected
0xAC0D/0x4C0D
AC-14 AO target voltage 2 -10.00 to 10.000 V Factory-
corrected
0xAC0E/0x4C0E
AC-15 AO measured voltage 2 -10.00 to 10.000 V Factory-
corrected
0xAC0F/0x4C0F
Note: Parameters in groups A1 and A5 are not displayed by default. They can be displayed by setting FP-02.

31.
5 Parameter Table
- 30 -
5.3 Monitoring Function Code
Para. No. Para. Name Comms. Address
Group U0: Monitoring Parameters
U0-00 Running frequency 0x7000
U0-01 Frequency reference 0x7001
U0-02 Bus voltage 0x7002
U0-03 Output voltage 0x7003
U0-04 Output current 0x7004
U0-05 Output power 0x7005
U0-07 DI state 0x7007
U0-08 DO state 0x7008
U0-09 AI voltage 0x7009
U0-10 Communication protocol 0x700A
U0-14 Load speed display 0x700E
U0-15 PID reference 0x700F
U0-16 PID feedback 0x7010
U0-17 PLC stage 0x7011
U0-18 Pulse reference 0x7012
U0-19 Feedback speed 0x7013
U0-20 Remaining running time 0x7014
U0-21 AI voltage before correction 0x7015
U0-24 Motor speed 0x7018
U0-25 Accumulative power-on time 0x7019
U0-26 Accumulative running time 0x701A
U0-27 Pulse reference 0x701B
U0-28 Communication reference 0x701C
U0-30 Main frequency reference 0x701E
U0-31 Auxiliary frequency reference 0x701F
U0-32 Viewing any register address value 0x7020
U0-37 Power factor angle 0x7025
U0-41 DI state display 0x7029
U0-42 DO state display 0x702A
U0-45 Fault information 0x702D
U0-59 Frequency Reference 0x703B
U0-60 Running frequency 0x703C
U0-61 AC drive state 0x703D
U0-62 Current fault code 0x703E
U0-64 Number of slaves 0x7040

32.
6 Troubleshooting
- 31 -
6. Troubleshooting
6.1 AC Drive Performance Fine Tuning
Time
Start Acceleration Nominal speed Deceleration Stop
Frequency Demand
Stage Symptom Diagnostics Remedies
Start Rollback Start frequency is too low Increase F6-03, ranging 0 to10 Hz
Torque output is insuf cient Make sure F3-00 = 0, F3-01 = 0
Starting jerk Start frequency is too high Decrease F6-03, ranging 0 to 10 Hz
Acceleration Jerk when
acceleration starts
Too fast acceleration at this section Increase F6-08, ranging 0 to (100-(F6-09))%
Or increase F0-17, ranging 0 to 6500s
Jerk when
acceleration end
Too fast acceleration at this section Increase F6-09, ranging 0 to (100-(F6-08))%
Or increase F0-17, ranging 0 to 6500s
Vibration Overcurrent stall prevention occurs It reaches current limit
Nominal speed Vibration Too big current loop PI gains Double check the motor parameters and then perform
motor auto-tuning once more
Deceleration Vibration Overcurrent stall prevention occurs it reaches current limit
Stop Jerk Too strong DC injection at stop Decrease F6-13, ranging 0 to 100%
Slip Too short DC injection active time at
stop
Increase F6-14,ranging 0 to 100s
Too weak DC injection at stop Increase F6-13, ranging 0 to 100%
Braking device applies too late check the timing of braking device

33.
6 Troubleshooting
- 32 -
6.2 Fault Codes and Troubleshooting
Display Fault Name Possible Causes Solutions
Overcurrent during
acceleration
Ground fault or short circuit exists in the output
circuit.
Check whether short-circuit occurs on the motor,
the motor cable or contactor.
Acceleration time is too short. Increase acceleration time.
Customized torque boost or V/F curve is not
appropriate.
Adjust the customized torque boost or V/F curve.
The voltage is too low. Adjust the voltage to normal range.
The spinning motor is started. Enable the catching a spinning motor function or
start the motor after it stops.
A load is added suddenly during acceleration. Cancel the suddenly added load.
The AC drive power class is small. Replace a drive of larger power class.
The braking resistor resistance is small.
The braking resistor is short circuited.
Replace a new braking resistor.
Overcurrent during
deceleration
Ground fault or short circuit exists in the output
circuit.
Check whether short-circuit occurs on motor,
motor cable or contactor.
Acceleration time is too short. Increase acceleration time.
The voltage is too low. Adjust the voltage to normal range.
A load is added suddenly during deceleration. Cancel the suddenly added load.
Braking unit and braking resistor are not
installed.
Install braking unit and braking resistor.
The braking resistor resistance is small.
The braking resistor is short circuited.
Replace a new braking resistor.
Overcurrent at
constant speed
Ground fault or short circuit exists in the output
circuit.
Check whether short-circuit occurs on the motor,
motor cable or contactor.
The voltage is too low. Adjust the voltage to normal range.
A load is added suddenly during running. Cancel the suddenly added load.
The AC drive power class is small. Replace a drive of larger power class.
The braking resistor resistance is small.
The braking resistor is short circuited.
Replace a new braking resistor.
Overvoltage during
acceleration
Input voltage is too high. Adjust input voltage to normal range.
An external force drives motor during
acceleration.
Cancel the external force.
Braking unit and braking resistor are not
installed.
Install braking unit and braking resistor.
Acceleration time is too short. Increase acceleration time.
Overvoltage during
deceleration
Input voltage is too high. Adjust input voltage to normal range.
An external force drives motor during
deceleration.
Cancel the external force or install braking
resistor.
Deceleration time is too short. Increase deceleration time.
Braking unit and braking resistor are not
installed.
Install braking unit and braking resistor.
Overvoltage at
constant speed
Input voltage is too high. Adjust input voltage to normal range.
An external force drives motor during running. Cancel the external force or install a braking
resistor
Control power fault Input voltage is not within the permissible
range.
Adjust the input voltage in the permissible range.

34.
6 Troubleshooting
- 33 -
Display Fault Name Possible Causes Solutions
Undervoltage Instantaneous power failure occurs Reset the fault.
The AC drive's input voltage is not within the
permissible range.
Adjust the voltage to normal range.
The bus voltage is abnormal. Replace the AC drive.
The recti er bridge, the pre-charge resistor, the
drive board or the control board are abnormal.
Replace the AC drive.
Drive overload Load is too heavy or locked-rotor occurs on
motor.
Reduce load or check motor and mechanical
conditions.
The AC drive power class is small. Replace a drive of larger power class.
Motor overload F9-01 (Motor overload protection gain) is set
improperly.
Set F9-01 correctly.
Load is too heavy or locked-rotor occurs on
motor.
Reduce load or check motor and mechanical
conditions.
The AC drive power class is small. Replace a drive of larger power class.
Output phase loss Motor winding is damaged. Check resistance between motor wires.
Replace motor is winding is damaged.
The cable connecting the AC drive and the
motor is abnormal.
Check for wiring errors and ensure the output
cable is connected properly.
The AC drive's three-phase outputs are
unbalanced when the motor is running.
Check whether the motor three-phase winding is
normal.
The drive board or the IGBT is abnormal. Replace the AC drive.
IGBT overheat The ambient temperature is too high. Lower the ambient temperature.
The ventilation is clogged. Clean the ventilation.
The fan is damaged. Replace the cooling fan.
Thermally sensitive resistor of IGBT is
damaged.
Replace the AC drive.
The inverter IGBT is damaged. Replace the AC drive.
External equipment
fault
External fault signal is input via DI. Con rm that the mechanical condition allows
restart (F8-18) and reset the operation.
External fault signal is input via virtual I/O. Con rm that the virtual I/O parameters in group
A1 are set correctly and reset the operation.
Communication
fault
Host computer is in abnormal state. Check the cable of host computer.
Communication cable is abnormal. Check the communication cables.
Communication parameters in group Fd are set
improperly.
Set communication parameters in group Fd
properly.
After all the preceding checkings are done but the fault still exists, restore the default settings.
Current detection
fault
The drive board is abnormal. Replace the AC drive.
EEPROM read-
write fault
EEPROM chip is damaged
Replace the AC drive.

35.
6 Troubleshooting
- 34 -
Display Fault Name Possible Causes Solutions
Short circuit to
ground
Motor is short circuited to the ground. Replace cable or motor.
Top tube of the inverter is damaged. Ask
professional to check.
Replace the AC drive.
Accumulative
running time
reached
Accumulative running time reaches the setting
value.
Clear the record through parameter initialization.
User-de ned fault 1 User-de ned fault 1 is input via DI. Reset the operation.
User-de ned fault 1 is input via virtual I/O.
User-de ned fault 2 User-de ned fault 2 is input via DI. Reset the operation.
User-de ned fault 2 is input via virtual I/O.
Accumulative
power-on time
reached
Accumulative power-on time reaches the
setting value.
Clear the record through parameter initialization.
Off load fault The output current of AC drive is smaller than
F9-64 (load loss detection level).
Check whether load is disconnected or the setting
of F9-64 and F9-65 (load lost detection time)
satis es actual running condition.
PID feedback lost
during running
PID feedback is smaller than the setting value
of FA-26 (detection level of PID feedback loss).
Check PID feedback or set FA-26 properly.
Quick current limit Load is too heavy or locked-rotor occurs on
motor.
Reduce load or check motor and mechanical
conditions.
The AC drive power class is small. Replace a drive of larger power class.
Slave faulty in
speed synchronous
When speed synchronous is enabled, the
master receives CAN communication data
but does not detect the salve. Then Err55 is
reported.
1. Check the slave CAN communication cable
connection.
2. Check whether CAN communication of the
slave is normal.

36.
6 Troubleshooting
6.3 Symptoms and Diagnostics
Fault Name Possible Causes Solutions
There is no display at
power-on.
The mains voltage is not input or too low. Check the power supply.
The AC Drive is damaged. Replace the AC drive.
is dis-
played at power-on.
Wire between drive board and control board is in poor
contact.
Re-connect the 4-pin wire and 28-pin wire.
Control board is damaged Replace the AC drive.
The motor or motor cable is short circuited to ground. Check whether short-circuit occurs on motor,
motor cable or contactor.
The mains voltage is too low. Check the power supply.
The mains voltage is too low.
( I G B T
overheat) is detected
frequently.
The setting of carrier frequency is too high. Reduce carrier frequency (F0-15).
The cooling fan is damaged, or ventilation is clogged. Replace the fan or clean the ventilation.
Components inside the AC drive are damaged
(thermistor or others).
Replace the AC drive.
The motor does not
rotate after the AC drive
runs.
It is motor or motor cable problem. Check that wiring between AC drive and motor is
normal.
Related AC drive and motor parameters are set
improperly.
Restore the factory parameters and re-set the
motor parameters properly.
The drive board is faulty. Replace the AC drive.
The DI terminals are
disabled.
Related parameters are set incorrectly. Check and set parameters in group F4 again.
External signals are incorrect. Re-connect external signal cables.
The control board is damaged. Replace the AC drive.
The AC drive detects
overcurrent and
overvoltage frequently.
Motor parameters are set improperly. Set motor parameters or perform motor auto-
tuning again.
Acceleration/deceleration time is improper. Set proper acceleration/deceleration time.
Contact the agent or Fuji-Engineering.
Revision History
Revision Date Description
V0.0 January 24, 2016
A01 March 22, 2016
FUJI ENGINEERING (THAILAND) CO., LTD
98/6 Sethsiri Rd, T. Tanoon nakornchaisri, A.Dusit, Bangkok, 10300
Tel: 662 102-0599
Fax: 662 102-0598
Website: www.Fuji-Engineering.com