SID

1. Iraq Asiacell Wireless Project
Sector Existing antenna type
Target antenna
type Height Site Solution Scenario Remarks (if Any)
A 1xODI-065R17M18JJ-GQ Reuse 24
Rooftop tower/DBS with RRU
on tower
B 1xODI-065R17M18JJ-GQ Reuse 24
C 1xODI-065R17M18JJ-GQ Reuse 24
Site Information: NAJ2257
Site Name: Oroba2_NAJ2257

2. Installation Material List

3. Dismantled Material List
Dismantled Material information
S.No Item Description Product Type Item Quantity
1 900M RRU Radio 2219 B8 3
2 1800M RRU 1*RRUS 12 B3 +
2*Radio 2219 B3
3
3 2100M RRU Radio 2219 B1 3
5 RBS BBU Other 2
6 RRU Power Cable 9
7 RRU Fiber Cable 9
8 Jumper Cable 18

4. NAJ2257 Site Installation Design
Site BBU installation
BBU5900
Install New BBU5900+UMPTga2;
Install 1*UBBPg2;
Connect BBU Power cable on 2*25A CB;
Connect BBU using Fiber to Transmission Device
After dismantling Ericsson BBU please install New
BBU5900 in middle of cabinet
New BBU
Transmission Device
E// BBU
Description of work :-
BBU5900-0-0
UBBPg2 UL
FANf
UMPTga2 GUL
UPEUe

5. Nokia MW Port Slot for fiber link (5)
Fiber port Connectivity Design in Transmission Device

6. BBU Installation design
BBU5900-0-0
UBBPg2 UL
FANf
UMPTga2 GUL
UPEUe
0-60-0
RRU5909
GU 900M
Sector 1
0-61-0
RRU5909
GU 900M
Sector 2
0-62-0
RRU5909
GU 900M
Sector 3
0-120-0
RRU5502
GL&UL
1800M&2100M
Sector 1
0-121-0
RRU5502
GL&UL
1800M&2100M
Sector 2
0-122-0
RRU5502
GL&UL
1800M&2100M
Sector 3
➊ In BBU5900:Install 1xUBBPg2 in Slot4
➋ In BBU5900:Install 1xUMPTga2 in Slot7
➌ Connect 3 CPRI cable from RRU5909 to
UBBPg2 in Slot-4, port 0,1,2 with 6.144G
SFP
➍ Connect 3 CPRI cables from RRU5502 to
UBBPg2 in Slot-4 port 3,4,5 with 9.8G
SFP

7. Power Connection for BBU and RRU on Circuit Breaker
CB Requirement For BBU and RRU:
Preparation Day:
1. Use any free CB for BBU pre integration(if no free CB ignore this step)
Cutover Day:
1. Disconnect existing E// RRU CB(sector by sector)
2. RRU5502 1800/2100M: replace existing RRU 25A CB to New 40A(LLVD).
3. RRU5909 900M: 25A for one PCS RRU(LLVD)
4. Disconnect existing E// BBU CB
5. BBU5900:Reuse free CB 2X25A (BLVD) , if 25A CB not free then replace free CB to
25A(dismantled from step2)

8. NAJ2257 Site Installation Design
RRU installation
Preparation Day:
1.Lay new RRU fiber and Power cable before cutover day; pre install new RRU if there is temp space available on tower;
2.Take Existing Antenna/RRU Photo /antenna down-tilt /azimuths and coverage Photo;
Cutover Day:
1.Dismantle Ericsson RRU/RRM(bracket)/Filter/jumper sector by sector
2.Install RRU5909 and RRU5502 on existing antenna poles;
3.Connect RRU Jumpers, power cable and fiber cable;
4.Pack dismantled E// RRU , BBU and cables etc.
Description of work :-
RRU5909
RRU5502
RRU Position

9. Antenna jumper connection
From To
RRU Port Connector Type Antenna type Port Connector type
RRU5909
A 4.3-10
ODI-065R17M18JJ-GQ
R1(+45) 4.3-10
B 4.3-10 R1(-45) 4.3-10
RRU5502
A 4.3-10 Y2(+45) 4.3-10
C 4.3-10 Y2(-45) 4.3-10
D 4.3-10 Y1(+45) 4.3-10
B 4.3-10 Y1(-45) 4.3-10
Note: New jumper connection shall follow the existing jumper connection, if there is any mismatch with above design table, please follow existing
jumper connection on antenna side and contact Huawei team.
Sector 1
ODI-065R17M18JJ-GQ
0-120-0
RRU5502
GL&UL
1800M&2100M
Sector1
0-60-0
RRU5909
GU 900M
Sector1
900
Filter
Sector 2
ODI-065R17M18JJ-GQ
0-121-0
RRU5502
GL&UL
1800M&2100M
Sector2
0-61-0
RRU5909
GU 900M
Sector2
900
Filter
Sector 3
ODI-065R17M18JJ-GQ
0-122-0
RRU5502
GL&UL
1800M&2100M
Sector3
0-62-0
RRU5909
GU 900M
Sector3
900
Filter
1. Always for 900
technology reuse
existing 900 filter.
2. Keep the jumper
between Antenna and
Filter as it is.
3. Install new jumper
between 900 filter and
900 RRU5909.