Diese Präsentation wurde erfolgreich gemeldet.
Wir verwenden Ihre LinkedIn Profilangaben und Informationen zu Ihren Aktivitäten, um Anzeigen zu personalisieren und Ihnen relevantere Inhalte anzuzeigen. Sie können Ihre Anzeigeneinstellungen jederzeit ändern.


This ppt contains brief introduction, construction, working, advantages & disadvantages of cryocar.

  • Loggen Sie sich ein, um Kommentare anzuzeigen.


  1. 1. Technical Seminar presentation on CRYOCARCRYOCAR Presented by Chethan S A 4BB13ME015 Under the Guidance of Mr.Theju H.S. B.E., M.tech., Assistant Professor DEPARTMENT OF MECHANICAL ENGINEERINGDEPARTMENT OF MECHANICAL ENGINEERING Bahubali College of Engineering Shravanabelgola-573 135 2016-17 1
  2. 2. CONTENTSCONTENTS 1. Introduction 2. History 3. LN2000’s Liquid Nitrogen Propulsion System 4. Parts of a Liquid Nitrogen Propulsion System 5. Power Cycle 6. Advantages 7. Disadvantages 8. LN2000 Vehicle 9. Conclusion 10. References 2
  3. 3. INTRODUCTIONINTRODUCTION 3 The importance of cars in the present world is increasing day by day. There are various factors that influence the choice of the car. These include performance, fuel consumption, pollution etc. As the prices for fuels are increasing and the availability is decreasing we have to go for alternative choice. Here an automotive propulsion concept is presented which utilizes liquid nitrogen as the working fluid.
  4. 4. HISTORYHISTORY Researchers at the University of Washington are developing a new zero-emission automobile propulsion concept. That uses liquid nitrogen as the fuel. The principle of operation is like that of a steam engine(open Rankine cycle). In this liquid nitrogen at –320° F (–196° C) is pressurized and then vaporized in a heat exchanger. This heat exchanger is like the radiator of a car. 4
  5. 5. LN2000’S LIQUID NITROGEN PROPULSIONLN2000’S LIQUID NITROGEN PROPULSION SYSTEMSYSTEM 5 Fig. No. 1: LN2000’s Liquid Nitrogen Propulsion System
  6. 6. PARTS OF A LIQUID NITROGEN PROPULSIONPARTS OF A LIQUID NITROGEN PROPULSION SYSTEMSYSTEM 6 The main parts of a liquid nitrogen propulsion system are: 1. Cryogen Storage Vessel. 2. Pump. 3. Economizer. 4. Expander Engine. 5. Heat exchanger.
  7. 7. 1. CRYOGEN STORAGE VESSEL1. CRYOGEN STORAGE VESSEL 7  It is a storage tank which is used to store and insulate the liquid nitrogen at -196°c. It should have Resistance to deceleration forces, low boil-off rate, minimum size and mass, reasonable cost etc. It is generally made up of titanium or aluminum alloys for the inner and outer vessels. Moderately high vacuum with super insulation type vessel is used prevent boil-off rates.
  8. 8. 2. PUMP2. PUMP 8 The pump is used to pump the liquid nitrogen into the engine. The pump which are used for this purpose have an operating pressure ranging between 500 – 600 Psi (35-42 bars). As the pump, pumps liquid instead of gas, it is noticed that the efficiency is high.
  9. 9. 3. ECONOMIZER3. ECONOMIZER A pre heater, called an economizer, uses leftover heat in the engine's exhaust to preheat the liquid nitrogen. Hence the economizer acts as a heat exchanger between the incoming liquid nitrogen and the exhaust gas which is left out. This is similar to the regenerative process which is done in steam power plant. Hence with the use of the economizer, the efficiency can be improved. 9
  10. 10. 10 LN2 at -320°F(-196°C) is pressurized and then vaporized in a heat exchanger by ambient temperature of atmosphere. The heat exchanger used is similar to radiator of car but instead of using air to cool water, it uses air to heat and boil LN2. Liquid LN2 passing through the primary heat exchanger quickly reaches its boiling point. Heat exchanger is made up of aluminum tubes with outside diameter of 10mm and wall thickness of 1mm. 4. HEAT EXCHANGER4. HEAT EXCHANGER
  11. 11. 11 The maximum work output of the LN2 engine results from an isothermal expansion stroke. Thus, engines having expansion chambers with high surface- to-volume ratios are favored for this application. Rotary expanders such as the Wankel may also be well suited.  A secondary fluid could be circulated through the engine block to help keep the cylinder walls as warm as possible. 5. EXPANDER5. EXPANDER
  12. 12. POWER CYCLEPOWER CYCLE 12 Fig. No. 2: Temperature Entropy Diagram For Open Rankine Cycle
  13. 13. Cont...Cont... There are many thermodynamic cycles available for utilizing the thermal potential of liquid nitrogen. These range from the Brayton cycle, to using two and even three fluid topping cycles. The easiest to implement, however, and the one chosen for this study, is shown in figure 2.(Rankine cycle). State 1 is the cryogenic liquid in storage at 0.1 MPa and 77 K. 13
  14. 14. Cont...Cont... The liquid is pumped up to system pressure of 4 MPa (supercritical) at state 2 and then enters the economizer. State 3 indicates N2 properties after it is being preheated by the exhaust gas. Further heat exchange with ambient air brings to N2 300k at state 4 Isothermal expansion to 0.11 MPa at state 5 would result in the N2 exhaust having enough enthalpy to heat the LN2 14
  15. 15. ADVANTAGESADVANTAGES  The process to manufacture liquid nitrogen in large quantities can be environmentally very friendly (Liquification).  Produces no or less air pollution and pollutants to atmosphere results in greater environmental benefits.  The operating cost is very less as compared to cost of fossil fuels.  LN2 powered car offer many safety advantages over commercial cars. 15
  16. 16. DISADVANTAGESDISADVANTAGES The N2 passing through the tubes of the heat exchanger obstruct the air flow (Icing problem). The nitrogen car be kept in a poorly ventilated space and, if the Nitrogen leaks off, it could prove fatal. Turning N2 gas into a liquid requires a lot of energy. The principal disadvantage is the inefficient use of primary energy. 16
  17. 17. LN2000 VEHICLELN2000 VEHICLE 17 Fig. No. 3: Inner Components of LN2000 Fig. No. 4: LN2000 Vehicle
  18. 18. CONCLUSIONCONCLUSION The potential for utilizing the available energy of liquid nitrogen for automotive propulsion looks very promising. Time to recharge (refuel), infrastructure investment, and environmental impact are among the issues to consider. The convenience of pumping a fluid into the storage tank is very attractive. Manufacturing LN2 from ambient air inherently removes small quantities of atmospheric pollutants 18
  19. 19. REFERENCESREFERENCES 19 JOURNALS [1] Abilash Vijayrao Nishane, (2016) “Cryogenic Liquid Nitrogen as a Fuel for Zero Emission Vehicles (Z.E.V)”, International Journal and Magazine of Engineering, Technology, Management and Research. [2] Rahul Singh Choudhary, (2015) “Hydrogen as a Non-Polluting Fuel”, International Journal of Advance Research, IJOAR.org. [3] Akil Garg, Kartik Jakhu, Kishan Singh, (2015) “Cryogenic Technology and Rocket Engines” International Journal of Aerospace and Mechanical Engineering. [4] Pankaj Soni, Gopal Sahu, Prakash Kumar Sen, Ritesh Sharma, (2014ss) “A Review on Cryogenic Engine” International Journal for Research in Science and Engineering Technology (IJRASET).
  20. 20. 20