Diese Präsentation wurde erfolgreich gemeldet.
Wir verwenden Ihre LinkedIn Profilangaben und Informationen zu Ihren Aktivitäten, um Anzeigen zu personalisieren und Ihnen relevantere Inhalte anzuzeigen. Sie können Ihre Anzeigeneinstellungen jederzeit ändern.

August 2015 f4 Toolholders

120 Aufrufe

Veröffentlicht am

  • Als Erste(r) kommentieren

  • Gehören Sie zu den Ersten, denen das gefällt!

August 2015 f4 Toolholders

  1. 1. August 2015 | AdvancedManufacturing.org 69 ToolHolders Picking the Right Toolholder for the Toughest Jobs APN Inc. has located its powRgrip tool-changing unit near the cells of high-speed, high-performance three and five-axis machining centers. One employee is in charge of setting up the Rego-Fix tooling, though all of the shop’s machinists know the system and will change their own tooling if necessary. Jim Lorincz Senior Editor Workpiece materials, spindle speeds, shapes, and sizes all play a role W hen sizing up an application for a milling toolholder, it is necessary to consider the materials being machined, how aggressively metal is going to be removed, and any machining conditions that are likely to present a challenge to tooling security. By now, the pros and cons of hydraulic, mechanical, and heat-assisted shrink- fit systems are well known and results well documented. Tools must perform under widely different machining conditions, but the most common requirement is that tools are held with strong gripping force to provide the best runout, the highest precision, and least opportunity for quality-robbing vibration. Toolholding solutions are available to guard against catastrophic failure due to cutter pullout in machining the toughest materials or in high- speed or high-production applications, often using standard cutters wherever possible.
  2. 2. 70 AdvancedManufacturing.org | August 2015 Toolholder Change for Truck Steering Component Is Big Winner Changes from one toolholding system to another can have significant impact on the cycle times and productivity even in the highest volume applications. In a high-volume machining environ- ment like the automotive and trucking industries, changing toolholders isn’t something that is done without sufficient confidence that the change will positively affect cycle time, production, and quality. Such was the case at an automotive manu- facturer based in the Midwest. Two specific end-milling applications for a nodular iron sand- cast component for a truck steering column were evaluated to find a solution for too-frequent tool changes due to excessive wear. The castings which were somewhat difficult to hold were being machined on Feeler vertical machining centers. Using hydraulic toolholders, the inserts had to be indexed after 400 cycles for a total of 800 parts. Annual requirement is 1.4-million assemblies, each consisting of one of these machined parts. The customer’s manufacturing engineer was looking for a solution to extend uptime on the application by testing other grades of inserts. “I was brought in to look at a milling ap- plication where tool life was very poor,” said Brett Kischnick, application engineer, Horn USA Inc. (Franklin, TN). “I felt that the Fahrion Centro P toolholding system could offer consider- able improvement over the hydraulic toolholder that was being used for the 1" [25.4-mm] indexable end mill with ¾" [19.05- mm] shank,” said Kischnick. The switch to the Fahrion Centro P toolholder using the same indexable inserts improved tool life to 600 cycles for a total of 1200 parts. “At first I did not be- lieve Mr. Kischnick when he said the Fahrion toolholders would make a substantial increase in tool life but am certainly glad I gave it a try,” said the manufacturing engineer. The Fahrion toolholder system consists of a new toolholder, a new collet, and a new nut. An adjustable torque wrench is used to properly torque the collet nut down, tightening it exactly the same way each time. “The holder and the nut have a thicker cross section that allows the extra torque without deforming the collet. In addition, the extra reinforcement of the chuck body to the diameter of the clamping nut produces superior stability with maximum compactness,” said Kischnick. The Fahrion Centro P features clamping torque of the clamping nut of 140 N•m with tool shank hardened, ground ToolHolders Auto supplier switched from a hydraulic toolholder to the Fahrion Centro P toolholder from Horn USA for machining a nodular iron forging component for a truck steering column. Using the same indexable inserts, the toolhold- er improved tool life to 600 cycles for a total of 1200 parts from 400 cycles and 800 parts.
  3. 3. August 2015 | AdvancedManufacturing.org 71 Rz 2.5, and free of grease. The holder offers 100% higher clamping force than standard collet chucks, the toolholder is ground to 1-µm taper in the front to taper in the back. The collet is a maximum of 2 µm therefore the combined system runout accuracy is less than 3 µm. A high degree of concentricity and repeatability of the Centro P toolholding system is ensured by the 30° trapezoidal thread with ground, extra-long, double- length guide. “The ground thread and guide ensure perfect centering of the clamping nut on the chuck, achieving even distribution of load and minimal imbalance,” said Kischnick. “Clamping forces are distributed evenly over the gripped area of the cutting tool shank, making the Centro P suitable for dry processes and hard milling, and ideal for drilling, counter-sinking, reaming, milling, tapping, and high-performance, high- speed cutting applications.” Perfection Is Aero, Defense Company’s Requirement APN Inc. (Quebec, Canada) has invested in the latest advanced digital machining technology to enable it to meet requirements for manufactur- ing high-precision, difficult-to-machine components for the aerospace, automo- tive, defense, and optical industries, The family-owned company has a commit- ment to perfection which it “considers to be non-negotiable” and has ISO-9001 and AS 9100-C certifications and a DQCR certification from Pratt & Whitney. In its digital machining arsenal, APN numbers five Huron five-axis machin- ing centers with a maximum speed of 24,000 rpm and two three-axis machining centers with 18,000-rpm spindles. Turning is done with Naka- mura multiaxis CNC lathes, and grind- ing by CNC Combi-Tec CNC grind- ers. For its milling performance, APN management recognized the need for better performance from its toolholding which was inconsis- tent, particularly with regard to toolholder balance. Milling performance has been dramatically improved by switching to the powRgrip toolholding system from Rego-Fix When we introduced our MV Series wire EDM machines, we had a feeling they’d make waves. The never-before-seen design improvements have reinforced our leadership in the market—and sparked our customers’ success. No other machine on the market has our non-contact cylindrical drive technology, improved power supply and deeper submerged cutting capabilities—all backed by the reliable, expert support our customers expect. See what all the buzz is about at www.mcmachinery.com or call 866-994-7856. DISCOVER THE #1-SELLING EDM IN NORTH AMERICA LEADING THE CHARGE. ONE SOURCE. ENDLESS EXPERTISE. Cylindrical Drive Technology Revolutionary non-contact design Auto-Threader Allows up to 14 inches of through-part wire threading for tall parts Compact Head Design Easy indexing during operation For current open positions, please visit our website: www.mcmachinery.com or email: jobs@mcmachinery.com EOE M/F/D/V
  4. 4. August 2015 | AdvancedManufacturing.org 73 Tool Corp. (Indianapolis, IN). The switch from heat shrink fit toolholding and standard ER collet hold- ers was made to provide repeatability and balance consistency required for high-speed machining. APN is typically machining materials ranging from stainless steels, tool steels, Inconel, and tita- nium to copper, and plastic. Required machining tolerances for most of the shop’s parts are typi- cally 0.0005" (0.013 mm), with some as tight as 0.0002" (0.005 mm). Once installed the powRgrip system has delivered high concentricity (TIR) with deviations of less than 3 μm for tool lengths up to 3×D and length pre-adjustment with a repeat accuracy within 10 μm. Holders are now 100% balanced to G 2.5 at 22,000 rpm for steep taper-style holders and G 2.5 at 25,000 rpm for HSK-style powRgrip holders. APN’s high-speed, high-performance mill- ing machines now run either Rego-Fix powRgrip holders or ER collets. The company has one powRgrip tool-changing unit and more than 150 powRgrip holders that make up about 60% of the shop’s entire tooling. Some shrink-fit holders are still in use to get the promised tool- ing return on investment. Workpieces are typically small with three-quarters of them measuring less than 3" (76 mm) square, and half of those smaller than 1" (25.4-mm) square. Tool sizes are typically under 1/4" (6.4 mm) in diameter with some drills measuring as small as 0.015" (0.4-mm) diameter. Job lot sizes vary from five to a thousand with an average of about 20. Half of these are regularly scheduled jobs/orders, while the other half are first-run jobs. At any given time, APN can be processing as many as 500 completely different jobs on its shop floor at one time. Locking Tools Securely in Place by Holder Design Companies like APN are benefiting from the ability of the powRgrip tool- ToolHolders Nexteer manufacturing engineer Bryce Silvernail (left) and Horn USA’s Brett Kischnick, application/sales engineer, with the Fahrion toolholding solution that replaced hydraulic toolholders on VMCs machining a nodular iron sand-cast component for a truck steering column, producing a dramatic increase in tool life for indexable inserts.
  5. 5. 74 AdvancedManufacturing.org | August 2015 holding system to dampen vibration. This capability is critical as machine tool spindle speeds and feed rates continue to increase. It’s axiomatic: the better a toolholder controls or even eliminates vibration, the tighter its TIR. The tighter a holder’s TIR, the more it helps increase tool life as well as improve part accuracies and surface finishes. Rego-Fix’s powRgrip mechanical tool holding system and its follow on secuRgrip system ensure concentricity (TIR) and achieve high vibration dampening due to the functional contact surfaces between its toolholders and collets, and the collets and tool shanks. The powRgrip system absorbs vibrations by creating “material breaks.” The process starts with a cutting tool, typically made from anything from high-speed steel to car- bide to cobalt, with each material having its own specific vibra- tion frequency or harmonics. The cutting tool is held in a collet that is also made from a particular type of steel then inserted into a powRgrip toolholder made from a different type of steel. Unlike systems that require modified tool shanks, the secuRgrip system uses a special threaded insert or key that eliminates the need to alter cutters. The simple and effective design is part of the company’s well-established powRgrip mechanical toolholding system and one that allows the use of any off-the-shelf tool as long as it has a common standard Weldon flat on its shank. Rego-Fix’s powRgrip and secuRgrip are also faster than other systems when it comes to exchanging tools. Remov- ing a tool from a holder and installing another takes about 10 seconds. Heat-shrink holders, on the other hand, must be heated, the cutter installed, then put in a chiller for 2 or 3 minutes before the tool can be used. Mechanical-base tooling innovations such as Rego-Fix’s powRgrip and secuRgrip provide shops with solutions for their machining challenges, especially those involving tough materials such as titanium and Inconel. With these toolhold- ing systems, shops can increase cutting tool life, experience significant cost advantages and run their cutting tools at the highest speeds and feeds to increase productivity while also improving part surface finish quality. Existing powRgrip holders are easily transformed into a secuRgrip holder by simply threading the outside of any ToolHolders A fter several years of collaboration with two indus- trial associates from the Allgäu region of Germany, GROB engineers have found a solution for dealing with chips during a tool change: the GROB motor spindle with an intelligent spindle nose. With this GROB innova- tion, after an automatic tool change, the tool interface checks with ultra-precision for the presence of chips. Be- cause this chip-in-spindle check is also cycle-time neutral and no alterations are required in the machine‘s working area, for many machining centers this development is an excellent way for improving reliability during an automatic tool change. What happens is that sensors in the spindle nose detect any asymmetric deformation caused by chips at the tool fixing point and assess it. The information is transmit- ted via high-frequency radio signals to the machine control, which then flags up the faulty tool change. The energy for the sensors in the spindle nose is supplied through one stationary and one rotating induction coil. The combined electronics and gaging technology affect only the design of the spindle face. The reading is taken when the spindle is at a standstill immediately after tool clamping. When the reading is taking place, the feed axes move to the new machining position. The accuracy of the system is impres- sive. Chips are reliably detected, which at a distance of 150 mm from the face contact on the HSK A63 toolholder can cause a change in concentricity at the tool of only 0.01 mm. It is immaterial whether the chips are in the tool taper or in the face contact area. For more information from GROB Systems Inc., go to www.grobgroup.com, or phone 419-358-9015. Intelligent Spindle Nose for an Ultra-Precise Tool Change GROB motor spindle with an intelligent spindle nose detects chips during tool change.
  6. 6. August 2015 | AdvancedManufacturing.org 77 powRgrip PG 25 or PG 32 holder for accepting the cap nut. Rego-Fix can either supply the necessary thread specifica- tions or factory-threaded holders. The secuRgrip holders accommodate cutter diameters from 0.472" up to 1.000" (12–25.4 mm). And with holder body tensile strengths higher than those of the cutting tools being held, the secuRgrip holders will withstand cutting forces that could break the cutters before ever damaging the toolholder itself. Standard Tooling Works Well with Milling Chuck Design BIG Kaiser Precision Tooling Inc. (Hoff- man Estates, IL) has made two recent major product introductions: one aimed at machining the toughest heat-resistant su- peralloys with standard tools and the other aimed at handling the smallest tools down to 3-mm diameter with a hydraulic toolhold- ing system. “Up until recently, hydraulic chucks for very small tools, specifically for tools 3 mm/1/8", diameter weren’t available,” said Alan Miller, engineering manager. “The reason came down to how hydraulic chucks work. There is an interference fit between the bore of the hydraulic chuck and the cutting tool itself. We have been able to redesign the hydraulic system with a very tight tolerancing of the bore, allowing us to clamp down to 3-mm diameter. The new small hydraulic chuck is geared toward extremely high-speed finishing work for the medical and mold-and-die industries,” said Miller. “We can make them as small as HSK 32 for very high speed micro-style machining at spindle speeds up to 45,000 rpm and get the surface footage necessary for very fine surface finishing.” To address the issue of tool pull out that can be encoun- tered when machining heat-resistant superalloys (HRSA) like titanium and Inconel, BIG Kaiser has introduced its Mega Perfect Grip milling chuck. “One of the things that we’ve done is take the existing standard holder for end mills and used the Weldon flat to keep the tool from pulling out of the holder. We came up with a modification of our existing mill- ing chuck product line called the Mega Perfect Grip milling chuck. We insert a key basically inside of the Weldon flat that drops into a special location on the end-mill holders so that when you drop it in and rotate it so that the flat locks into an internal groove. Once you close the milling chuck, it isn’t possible for the product to pull out,” said Miller. The Mega Perfect Grip milling chucks combine the cut- ting performance of heavy-duty milling chucks with security against pullout of solid side lock toolholders. High-pressure and high-volume jet-through coolant is a standard feature. “We talk about Inconels and stainless steels, but alumi- num generates a lot of axial force at high speed and tries to pull the tool out of the holder. All of the tools for these applications, for high-speed aluminum and heavy roughing all require tool security. When people see the Mega Perfect Grip milling chucks, the simplicity of the system is obvious to them and it’s easy to implement,” said Miller. “Before these developments in secure toolholding, the only way to hold the tool was through side lock setscrew. But for today’s CAT 50 machines and the HSK A100 and A125 machines where you need a lot of horsepower and high torque for bigger heavy- duty aerospace applications, the Mega Perfect Grip milling chucks offer the toolholding security and confidence that manufacturers require,” said Miller. ToolHolders ? BIG Kaiser Precision Tooling Inc. 847-228-7660 / www.bigkaiser.com Horn USA Inc. 615-771-4100 / www.hornusa.com Rego-Fix Tool Corp. 317-870-5959 / www.rego-fix.com BIG Kaiser’s new small hydraulic chuck can handle tools down to 3-mm diameter for high-speed finishing work for the medical and mold and die industries.