Diese Präsentation wurde erfolgreich gemeldet.
Wir verwenden Ihre LinkedIn Profilangaben und Informationen zu Ihren Aktivitäten, um Anzeigen zu personalisieren und Ihnen relevantere Inhalte anzuzeigen. Sie können Ihre Anzeigeneinstellungen jederzeit ändern.

CFD analysis of aerofoil

It consists of basics of aerodynamics and CFD analysis of aerofoil.

  • Loggen Sie sich ein, um Kommentare anzuzeigen.

CFD analysis of aerofoil

  1. 1. STUDY OFAERODYNAMICS AND CFD ANALYSIS OF AEROFOIL Prepared By: Neel Thakkar(MH73) Guided By: D.I.Upadhyay
  2. 2. Outline Of Presentation Introduction The Atmosphere Aerofoil and terminologies Forces acting on Aircraft Stability of Aircraft CFD analysis of Aerofoil Conclusion References
  3. 3. Aerodynamics : Aerodynamics is the study of objects in motion through the air and the forces that produce or change such motion. Chapter 1: INTRODUCTION It is unnecessary that a mechanic be totally versed on Aerodynamics and Theory of Flight. However he must understand the relationships between the atmosphere, the aircraft and the forces acting on it in flight, in order to make intelligent decisions affecting the flight safety of both airplanes and helicopters.
  4. 4. The Atmosphere : Air is a mixture of gases composed principally of nitrogen and oxygen. An aircraft operates in the air therefore, the properties of air that affect aircraft control and performance must be understood. Pressure – Atmospheric pressure varies with altitude. The higher an object rises above sea level, the lower the pressure. Density – It varies directly with the pressure and inversely with the temperature. With the same horse power, an aircraft can fly faster at high altitude because of less resistance of air at there. Humidity – Humidity is the amount of water vapor in the air. It varies directly with temperature.
  5. 5. BERNOULI'S PRINCIPLE: • Bernoulli's principle states that when a fluid flowing through a tube reaches a constriction or narrowing of the tube, the speed of the fluid passing through the constriction is increased and its pressure is decreased. • In B, air is flowing past a cambered surface, such as an aerofoil, and the effect is similar to that of air passing through a restriction.
  6. 6. Chapter 2: Aerofoil  An airfoil is the shape of a wing or blade (of a propeller, rotor or turbine) as seen in cross-section.  An aircraft's wings, horizontal, and vertical stabilizers are built with airfoil-shaped cross sections, as are helicopter rotor blades. Mean camber line Chord line
  7. 7. Aerofoil Terminology and Definitions: • Blade span—the length of the rotor blade from centre of rotation to tip of the blade. • Chord line—a straight line intersecting leading and trailing edges of the aerofoil. • Chord—the length of the chord line from leading edge to trailing edge; it is the characteristic longitudinal dimension of the aerofoil section. • Mean camber line—a line drawn halfway between the upper and lower surfaces of the aerofoil. The chord line connects the ends of the mean camber line. The profile thickness and thickness distribution are important properties of an aerofoil section. • Leading edge— the front edge of an aerofoil is known as leading edge. • Flight path velocity—the speed and direction of the aerofoil passing through the air. For aerofoil on an airplane, the flight path velocity is equal to true airspeed (TAS) • Centre of pressure—an aerofoil at an angle of attack α experiences a resultant aero- dynamic force, and the point on the chord through which the line of action passes is called the centre of pressure. • Aerodynamic Centre--It is not the same as the centre of pressure which does move as angle of attack changes. It is the point about which the clockwise and anticlockwise moments remain constant with changing angle of attack.
  8. 8. • Angle of attack (AOA)—the angle measured between the resultant relative wind and chord line. The angle of attack is the angle between the chord line and the average relative wind. • Greater angle of attack creates more lift (up to a point). AOA is an aerodynamic angle and not easy to measure. It can change with no change in the blade pitch angle. • When the AOA is increased, air flowing over the aerofoil is diverted over a greater distance, resulting in an increase of air velocity and more lift. As the AOA is increased further, it becomes more difficult for air to flow smoothly across the top of the aerofoil. • At this point, the airflow begins to separate from the aerofoil and enters a burbling or turbulent pattern. The turbulence results in a large increase in drag and loss of lift in the area where it is taking place. • Increasing the AOA increases lift until the critical angle of attack is reached. Any increase in the AOA beyond this point produces a stall and a rapid decrease in lift.
  9. 9. Aerofoil Types: • There are mainly two types of aerofoil. 1 Symmetrical Aerofoil 2 Nonsymmetrical Aerofoil (Cambered) Symmetrical Aerofoil • The symmetrical aerofoil is distinguished by having identical upper and lower surfaces. The mean camber line and chord line are the same on a symmetrical aerofoil, and it produces no lift at zero AOA. Most light aircrafts incorporate symmetrical aerofoils in the main rotor blades. Nonsymmetrical Aerofoil (Cambered) • The non symmetrical aerofoil has different upper and lower surfaces, with a greater curvature of the aerofoil above the chord line than below. • The mean camber line and chord line are different. The nonsymmetrical aerofoil design can produce useful lift at zero AOA. • The advantages are more lift production at a given AOA than a symmetrical design, an improved lift-to-drag ratio, and better stall characteristics. • The disadvantages are centre of pressure travel of up to 20 present of the chord line (creating undesirable torque on the aerofoil structure) and greater production costs.
  10. 10. Chapter 3: Forces Acting on the Aircraft Types of forces Once an airplane leaves the ground, it is acted upon by four aerodynamic forces; thrust, drag, lift and weight. • Lift—opposes the downward force of weight, is produced by the dynamic effect of the air acting on. The aerofoil, and acts perpendicular to the flight path through the centre of lift. • Drag—a rearward, retarding force caused by disruption of airflow by the wing, rotor, fuselage, and other protruding objects. Drag opposes thrust and acts rearward parallel to the relative wind. • Thrust—the forward force produced by the power plant/propeller or rotor. It opposes or overcomes the force of drag. As a general rule, it acts parallel to the longitudinal axis. However, this is not always the case, as explained later. • Weight—the combined load of the aircraft itself, the crew, the fuel, and the cargo or baggage. Weight pulls the aircraft downward because of the force of gravity. It opposes lift and acts vertically downward through the aircraft’s centre of gravity (CG).
  11. 11. 3.1 Lift: • Lift is generated when an object changes the direction of flow of a fluid or when the fluid is forced to move by the object passing through it. The lift generated by an aerofoil depends on such factors as: • Speed of the airflow • Density of the air • Total area of the segment or aerofoil • AOA between the air and the aerofoil • A symmetric aerofoil must have a positive AOA to generate positive lift. At a zero AOA, no lift is generated. At a negative AOA, negative lift is generated. • A cambered or non-symmetrical aerofoil may produce positive lift at zero, or even small negative AOA. • The majority of lift is the result of decreased pressure above the blade, rather than the increased pressure below it.
  12. 12. 3.3 Drag: • The force that resists the movement of an aircraft through the air and is produced when lift is developed is called drag. Drag must be overcome by the engine to turn the rotor. Drag always acts parallel to the relative wind. Total drag is composed of three types of drag: friction, induced, and parasite. 3.3.1 Friction Drag: • Profile drag develops from the frictional resistance of the blades passing through the air. • It does not change significantly with the aerofoil’s AOA, but increases moderately when airspeed increases. Profile drag is composed of form drag and skin friction. • Skin friction is caused by surface roughness. Even though the surface appears smooth, it may be quite rough when viewed under a microscope. A thin layer of air clings to the rough surface and creates small eddies that contribute to drag. 3.3.2 Wave drag coefficient: • The rapid increase in the drag coefficient due to the formation of shock waves at high speeds is called wave drag. • Shock waves cause the boundary layer to separate, thus increasing the drag. Wave drag begins at the Mach number for drag divergence Because a subsonic airplane will not fly above MD because the drag is too high.
  13. 13. 3.3.3 Induced Drag: • Induced drag is generated by the airflow circulation around the rotor blade as it creates lift. • The lift produced by the blade is perpendicular to the relative wind, the lift is inclined aft by the same amount. The component of lift that is acting in a rearward direction is induced drag. 3.3.4 Parasite Drag: • Parasite drag is present any time the aircraft is moving through the air. This type of drag increases with airspeed. Non-lifting components of the aircraft, such as the cabin, rotor mast, tail, and landing gear, contribute to parasite drag. • While parasite drag can be reduced by reducing the number of exposed parts.
  14. 14. 3.3.5 Total Drag: • Total drag for aircraft is the sum of all three drag forces. • As airspeed increases, parasite drag increases while induced drag decreases. Profile drag remains relatively constant throughout the speed range with some increase at higher airspeeds. Combining all drag forces results in a total drag curve. • The low point on the total drag curve shows the airspeed at which drag is minimized. This is the point where the lift-to-drag ratio is greatest and is referred to as L/DMAX. At this speed, the total lift capacity of the aircraft, when compared to the total drag of the aircraft, is most favourable. This is an important factor in aircraft performance • Drag Equation is given by: D=CD × ½ ρ × S × V2
  15. 15. 3.3 Weight: • Weight has a definite relationship with lift, and thrust with drag. These relationships are quite simple, but very important in understanding the aerodynamics of flying. • This weight force acts downward through a point called the centre of gravity (CG). The CG is the point at which all the weight of the aircraft is considered to be concentrated. 3.4 Thrust: • To overcome drag and move the aircraft forward, another force is essential. This force is thrust. Thrust is derived from jet propulsion or from a propeller and engine combination. • Jet propulsion theory is based on Newton’s third law of motion. The turbine engine causes a mass of air to be moved backward at high velocity causing a reaction that moves the aircraft forward.
  16. 16. There are two types of stability  Static Stability - The initial movement of an object after being disturbed. – Positive Static Stability – returns to position before displacement. – Neutral Static Stability – tendency to remain in displaced position. – Negative Static Stability – tends to continue away from displaced position in same direction.  Dynamic Stability - The behavior of the object over time. – Positive Dynamic Stability – the oscillations dampen themselves out. – Neutral Dynamic Stability – the oscillations carry on with out increasing in severity. – Negative Dynamic Stability – the oscillations increase in severity and diverge. Chapter 4 :Stability  An aircraft must have sufficient stability to maintain a uniform flight path and recover from the various upsetting forces also to achieve the best performance.
  17. 17. 4.1.1 Static Stability Positive-Neutral-Negative
  18. 18. CH 5: CFD Analysis of Supercritical Aerofoil 5.1 Supercritical Aerofoil • Mach numbers while retaining acceptable low-speed maximum lift and stalls characteristics and focused on a concept referred to as the supercritical aerofoil. • This characteristic aerofoil shape, based on the concept of resident supersonic flow with isentropic recompression, was considered by a large leading-edge radius, condensed curvature over the middle region of the upper surface, and considerable aft camber.
  19. 19. Serial no Input Value 1 Velocity of flow 0.6 Mach or 205.8 m/s 2 Operating temperature 300 k 3 Operating pressure 101325 Pa 4 Turbulence Model transition Spalart-Allmars 5 Density of fluid 1.225 kg/m3 6 Kinematic viscosity 1.4607*10-5 7 Reynolds number 3.5*106 8 AOA 0°-22.5° 9 Fluid Air as an ideal I. INPUTS AND BOUNDRAY CONDITIONS 5.1.1 Input and Boundary conditions It involves inlet, outlet & wall boundary the velocity components are calculated for each angle attack case as follows. All the outermost boundaries are considered as the “Pressure Far Field” boundary conditions in Fluent.
  20. 20. II. METHODOLOGY 5.2.1 Model creation • We get the model dimensions through coordinates, from these coordinates get from NASA website; we created a model in catia model as shown in figure 5.1. Thickness 13.9% Camber 1.55% Trailing edge angle 16.7° Lower flatness 9.4% Leading edge radius 2.9% Table 5.2: Aerofoil data Fig 5.1: Aerofoil NACA SC (2) 0714 Model
  21. 21. 5.2.2 Mesh generation • Meshed the above shows computational domain using Hyper Mesh 11. It has been created the surface meshes with the trais and the volume mesh is created with tetras. • The meshed model contains top surface, bottom surface, computational domain wall; pressure far filed wall and Pressure outlet surfaces. • It has 404867 tetra elements and 55918 nodes. • Meshed model shown in figure below.
  22. 22. 5.2.3 Solver step • Setting up of the solver is very important in any of the fluid flow problem; the solver setting indicates the method and also a procedure for solving (analysis) the problem. • The solver settings applied in Fluent for the simulations of Aerofoil are tabulated in Table 5.3. Table 5.3 Solver Setting Applied For Aerofoil
  23. 23. III. RESULTS AND DISCUSSIONS From the contours, we see that there is a region of high pressure at the leading edge (stagnation point) and region of low pressure on the upper surface of aerofoil. From Bernoulli equation, we know that whenever there is high velocity, we have low pressure and vice versa. 5.3.1 At 0° Angle of attack : • Figure shows that the maximum pressure and pressure appeared at leading edge is 29079.86Pa and the pressure appeared at trailing edge is 2390.27Pa and the Pressure Drag is measured by taking difference in static pressure at leading edge and trailing edge. • More difference means more pressure drag. So the pressure drag is 26689.59Pa and the average pressure around the aerofoil wall is -2847.358Pa. The static pressure at upper surface of the aerofoil wall -5950.22Pa and at lower surface is -5950.22Pa so the Lift of the aerofoil is not much high enough at this angle of attack.
  24. 24. 5.3.2 At 12° angle of attack : • The below figure shows that the contours of static pressure at the aerofoil wall and centre domain of the aerofoil. • It shows that the maximum pressure is appeared in plane is 41358.3Pa and pressure appeared at leading edge is 27624.89Pa and the pressure appeared at trailing edge is -3765.74Pa so the Pressure Drag is 31390.63Pa and the average pressure around the aerofoil wall is-2696.56Pa. • The static pressure at upper surface of the aerofoil wall -7689.6Pa and at lower surface is -3765.74Pa • So the Lift of the aerofoil is more than the drag.
  25. 25. 5.3.3 At 20° Angle of attack: • The below figure shows that the contours of static pressure at the aerofoil wall and centre domain of the aerofoil. It shows that the maximum pressure is appeared in plane is 69675.74Pa and pressure appeared at leading edge is 29648.28Pa and the pressure appeared at trailing edge is -4747.38Pa. • The average pressure around the aerofoil wall is -1881.45Pa and Pressure Drag is 34395.65Pa. The static pressure at lower surface of the aerofoil wall 2963.31Pa and at upper surface is -7710.69Pa • So the Lift of the aerofoil is more.
  26. 26. 5.3.4 At 22.5° angle of attack : • The figure shows that the contours of static pressure at centre domain of the aerofoil. The maximum pressure is appeared in plane is 78052.59Pa and pressure appeared at leading edge is 29005.72Pa and the pressure appeared at trailing edge is 309.223Pa. • So the Pressure Drag is also reduced as compare previous angle of attack, pressure drag is 28696.5Pa and the average pressure around the aerofoil wall is-1881.45Pa. • The static pressure at upper surface of the aerofoil wall 3039.725Pa and at lower surface is 2789.5Pa • So the Lift of the aerofoil is decrease.
  27. 27. • The figure 5.7 shows that the angle of attack v/s Lift and Drag coefficient plot. Drag coefficient will slightly increases with angle of attack but not like lift and the turbulence will be there at trailing edge but less as compared to leading edge. The pressure at trailing edge is compared to leading edge is very less and maximum velocity of the aerofoil is less at trailing edge so drag will not increases as like lift but drag will also be there. • After the 20° angle of attack pressure on upper surface of the aerofoil at leading edge is more as compare to lower surface of the aerofoil at leading edge so drag is increases gradually from 20° angle of attack.
  28. 28. • Lift coefficient will increases as the angle of attack increases because pressure on lower surface of the aerofoil at leading edge is more as compare to pressure on upper surface and turbulence is very high on the lower surface of the aerofoil at leading edge so Lift of the aerofoil will occur. • Lift of aerofoil is increased up to 20° angle of attack, after this angle of attack lift coefficient decreases gradually because the pressure on lower surface of the aerofoil is decreases than the upper surface of the aerofoil.
  29. 29. IV. CONCLUSION • It is found that the static pressure on the lower surface of the aerofoil at leading edge side is greater than static pressure on the upper surface of the aerofoil so the lift of aerofoil is increases gradually till 20° angle of attack, from this angle of attack the pressure on lower surface of the aerofoil is reduced than upper surface so lift of the aerofoil is decreasing and drag of the aerofoil is increasing. • Pressure Drag is calculated by taking difference in static pressure at leading edge and trailing edge. • More difference means more pressure drag. • At 20° Angle of attack pressure drag will increase and form 22.5° angle of attack pressure drag will decrease continuously.
  30. 30. References: [1] Whitcomb, Richard T.: Review of NASA Supercritical Airfoils. ICAS Paper No. 74-10, Aug. 1974 [2] Gaurav saxena , Mahendra Agrawal, Aerodynamic analysis of NACA 4412 airfoil using CFD, International Journal of Emerging Trends in Engineering and Development Issue 3, Vol.4 (June-July 2013) ISSN 2249-6149. [3] The Element 0f Aerofoil and Airscrew theory By H. Glauert. [4] Karna S. Patel, Saumil B. Patel, Utsav B. Patel, Prof. Ankit P. Ahuja, “CFD Analysis of an Aerofoil” International Journal of Engineering Research ISSN: 2319-6890), 2347- 5013.Volume No.3, Issue No.3, pp: 154-158 01 March 2014.
  31. 31. Thank you  Guided By: D.I.Upadhyay Sir