Molykote Products - call +91-891-2564393

1. PASTES Molykote® 44 Medium
THREAD PASTES/ANTI-SEIZE Molykote® 55M
Molykote® 1000 Dow Corning® High Vacuum Grease
Molykote® HSC Plus Molykote® PG-21
Molykote® P-37 Molykote® PG-54
Molykote® P-74 COMPOUNDS
ASSEMBLY PASTES Molykote® 111 Compound
Molykote® D Dow Corning® 4 Compound
Molykote® G-n Plus Dow Corning® 7 Compound
Molykote® G-Rapid Plus Dow Corning® 340 Heat Sink Compound
Molykote® M-77 HIGH PERFORMANCE INDUSTRIAL
GREASE PASTES LUBRICATING OILS
Molykote® Cu-7439 Plus MULTI-PURPOSE GEAR OILS
Molykote® DX Molykote® L-0532FG
Molykote® E Molykote® L-1122
Molykote® P-40 Molykote® L-1132
Molykote® P-1900 Molykote® L-1122FG
Molykote® TP-42 Molykote® L-1146FG
GREASES CHAIN OILS
MINERAL OIL GREASES Molykote® L-1428
Molykote® 1102 Molykote® L-1468FG
Molykote® 1122 Molykote® CO 220
Molykote® 165 LT Molykote® C40 High Temp Lubricant
Molykote® BR2 Plus Molykote® Omnigliss
Molykote® FB 180 Molykote® MKL-N
Molykote® G-0010 Bearing Grease COMPRESSOR OILS
Molykote® G-0052FG EP White Food Grade Molykote® L-4640 ( Flush oil )
Molykote® G-67 Molykote® L-4646 ( POE )
Molykote® Longterm 00 COATINGS
Molykote® Longterm 2 plus ANTI-FRICITON COATINGS
Molykote® Longterm W2 Molykote® 106
SEMI-SYNTHETIC GREASES Molykote® D-321R
Molykote® PG-75 Molykote® 3400A Leadfree
SYNTHETIC GREASES, PAO Molykote® 3402C
Molykote® EM-30L Molykote® 7400
Molykote® EM-50L Molykote® 7405
Molykote® EM-60L Molykote® 7409
Molykote® G-4500 Molykote® D-10
Molykote® G-4700 Molykote® PTFE-N UV
Molykote® YM-103 OTHER COATINGS
SYNTHETIC GREASES, POE Molykote® Metal Protector Plus
Molykote® BG-20 SOLVENTS
SYNTHETIC GREASES, FLUROSILICONE Molykote® 7414
Molykote® FS 1292 DISPERSIONS
Molykote® FS 3451 Molykote® M-55 Plus
Molykote® FS 3452 Molykote® Multigliss
SYNTHETIC GREASES, PFPE OTHER PRODUCTS
Molykote® HP-300 Molykote® Food Grade Spray Oil
Molykote® HP-870 Molykote® Supergliss
SYNTHETIC GREASES, SILICONE Molykote® 316 Silicone Release Spray
Molykote® 33 Light Dow Corning® 557 Silicone Spray
Molykote® 33 Medium Molykote® S-1011
Molykote® 41 POWDERS
Molykote® 44 Light Molykote® Microsize
Molykote® Z

2. Product Information
Specialty
Lubricants MOLYKOTE® Omnigliss Spray
Quick-action penetrating agent
FEATURES Quick-action penetrating agent incorporating corrosion
• Good penetration protection, water-repellent and lubricating properties
• Water repellent APPLICATIONS
• High pressure resistance • Suitable for frictional contacts, running at low to medium speeds, which are
• Temporary corrosion protection not equipped with grease nipples or oiling holes.
• Used on joints, levers, chains and other components of transport and conveyor
equipment, textile machinery, automatic filling units and all types of packaging
COMPOSITION equipment.
• Mineral oil
• Solid lubricants TYPICAL PROPERTIES
• Corrosion inhibitors Specification writers: These values are not intended for use in preparing specifications.
• Stabilizer Please contact your local Dow Corning sales representative prior to writing specifications
on this product.
Standard Test Unit Result
Color Light amber
Density
Density at 20°C g/ml 0.84
Viscosity at 40°C mm²/s 11.8
Temperature
Service temperature °C -30 to +80
Load-carrying capacity, wear protection, service life
Four-ball tester (VKA)
DIN 51 350 pt.4 Weld load N 2900
Weld scar under 800N load mm 1.1
HOW TO USE SAFETY DATA SHEET IS
AVAILABLE FROM YOUR LOCAL
How to apply DOW CORNING SALES
Shake before use. Can be applied with REPRESENTATIVE.
brush, oil can, spray-can, hand-held or
compressed-air spraying equipment,
USABLE LIFE AND
or by dipping. On badly corroded
parts, allow longer to react. Repeat if STORAGE
necessary. When stored at or below 20°C in the
original unopened containers, this
HANDLING PRECAUTIONS product has a usable life of 60 months
from the date of production.
PRODUCT SAFETY
INFORMATION REQUIRED FOR
SAFE USE IS NOT INCLUDED. PACKAGING
BEFORE HANDLING, READ This product is available in different
PRODUCT AND SAFETY DATA standard container sizes. Detailed
SHEETS AND CONTAINER container size information should be
LABELS FOR SAFE USE, obtained from your nearest
PHYSICAL AND HEALTH Dow Corning sales office or
HAZARD INFORMATION. THE Dow Corning distributor.

3. LIMITATIONS
This product is neither tested nor
represented as suitable for medical or
pharmaceutical uses.
HEALTH AND
ENVIRONMENTAL
INFORMATION
To support customers in their product
safety needs, Dow Corning has an
extensive Product Stewardship
organization and a team of Health,
Environment and Regulatory Affairs
specialists available in each area.
For further information, please
consult your local Dow Corning
representative.
WARRANTY
INFORMATION - PLEASE
READ CAREFULLY
The information contained herein is
offered in good faith and is believed
to be accurate. However, because
conditions and methods of use of our
products are beyond our control, this
information should not be used in
substitution for customer's tests to
ensure that Dow Corning's products
are safe, effective, and fully
satisfactory for the intended end use.
Dow Corning's sole warranty is that
the product will meet the
Dow Corning sales specifications in
effect at the time of shipment. Your
exclusive remedy for breach of such
warranty is limited to refund of
purchase price or replacement of any
product shown to be other than as
warranted. Dow Corning specifically
disclaims any other express or implied
warranty of fitness for a particular
purpose or merchantability. Unless
Dow Corning provides you with a
specific, duly signed endorsement of
fitness for use, Dow Corning
disclaims liability for any incidental
or consequential damages.
Suggestions of use shall not be taken
as inducements to infringe any patent.
2 05/01/1998 ® MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0173A-01 DC 3630 ©1997-2001 Dow Corning Corporation. All rights reserved.

4. Product Information
Specialty
Lubricants MOLYKOTE® 106
Anti-friction Coating
FEATURES Heat-curing dry lubricant
• Low coefficient of friction
• High load carrying capacity APPLICATIONS
• Protection from corrosion • For smooth coating of metal/metal combinations.
• Good adhesion • Maintenance-free, permanent lubrication of highly stressed friction
• Can be painted over combinations with low speeds or oscillating operation.
• Used where design construction prevents the use of oil or grease or where the
risk of soiling is undesirable.
COMPOSITION • This product is used successfully for the dry lubrication of locks, hinges, joints,
• Solid lubricants magnetic armatures and for the anti-seizure coating of engine and gear
• Organic binder components.
• Solvent
TYPICAL PROPERTIES
Specification writers: These values are not intended for use in preparing specifications.
Please contact your local Dow Corning sales representative prior to writing specifications
on this product.
Standard* Test Unit Result
Color Dark grey
Physical properties
DIN 53211/3 Viscosity at 20°C (DIN3 cup) s 42
DIN 53217/2 Density at 20°C g/ml 1.16
CTM 0242 I Non-volatile content % 41
Temperature
Curing time minutes/°C 60/150
Curing time minutes/°C 30/180
Service temperature range °C -70 to +250
Load-carrying capacity, wear protection, service life
ASTM-D2625 Falex load-carrying capacity¹ N p=13600*
s=11300*
ASTM-D2714 LFW-1, rotating¹ p=187*
F=2860N, n=72 minutesª¹,
v=7.9m/minutes
no. of revolutions x1000 to μ=0.1
ASTM-D2714 LFW-1, oscillating¹ p=409*
F=900N, frequency=89.5osc./minutes
no. of oscillations to μ=0.08
Corrosion protection
ISO/R 1456 Salt spray test h 2
1. * Surface:p = phosphatized, s = sand-blasted.
* CTM: Corporate Test Method, copies of CTMs are available on request.
ASTM: American Society for Testing and Materials.
DIN: Deutsche Industrie Norm

5. LIMITATIONS
HOW TO USE This product is neither tested nor
Surface preparation represented as suitable for medical or
pharmaceutical uses.
First clean and degrease the surface
which will be coated with
MOLYKOTE 106 Anti-Friction HEALTH AND
Coating. Phosphatization or ENVIRONMENTAL
sandblasting (180 grid) increases the INFORMATION
adhesion and service life. To support customers in their product
safety needs, Dow Corning has an
How to apply extensive Product Stewardship
Stir the Anti-friction Coating organization and a team of Health,
thoroughly before applying by Environment and Regulatory Affairs
spraying, dipping, centrifuging or specialists available in each area.
brushing. Recommended dry film
thickness: 5 to 20μm. For further information, please
consult your local Dow Corning
Curing representative.
60 minutes at 150°C,
30 minutes at 180°C WARRANTY
(Object temperature). INFORMATION - PLEASE
READ CAREFULLY
Solubility The information contained herein is
Thinning can be carried out using offered in good faith and is believed
MOLYKOTE® L 13 Thinner. to be accurate. However, because
conditions and methods of use of our
HANDLING PRECAUTIONS products are beyond our control, this
information should not be used in
PRODUCT SAFETY substitution for customer's tests to
INFORMATION REQUIRED FOR ensure that Dow Corning's products
SAFE USE IS NOT INCLUDED. are safe, effective, and fully
BEFORE HANDLING, READ satisfactory for the intended end use.
PRODUCT AND SAFETY DATA Dow Corning's sole warranty is that
SHEETS AND CONTAINER the product will meet the
LABELS FOR SAFE USE, Dow Corning sales specifications in
PHYSICAL AND HEALTH effect at the time of shipment. Your
HAZARD INFORMATION. THE exclusive remedy for breach of such
SAFETY DATA SHEET IS warranty is limited to refund of
AVAILABLE FROM YOUR LOCAL purchase price or replacement of any
DOW CORNING SALES product shown to be other than as
REPRESENTATIVE. warranted. Dow Corning specifically
disclaims any other express or implied
USABLE LIFE AND warranty of fitness for a particular
STORAGE purpose or merchantability. Unless
When stored at or below 20°C in the Dow Corning provides you with a
original unopened containers, specific, duly signed endorsement of
MOLYKOTE 106 Anti-Friction fitness for use, Dow Corning
Coating has a usable life of 36 months disclaims liability for any incidental
from the date of production. or consequential damages.
Suggestions of use shall not be taken
as inducements to infringe any patent.
PACKAGING
This product is available in different
standard container sizes. Detailed
container size information should be
obtained from your nearest
Dow Corning sales office or
Dow Corning distributor.
2 19/11/1998 ® MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0154B-01 DC 2935 ©1997-2001 Dow Corning Corporation. All rights reserved.

6. Product Information
Specialty
Lubricants MOLYKOTE® 1102
Grease
FEATURES For gas taps and cocks with metal, glass and plastic
• Highly resistant to water combinations
• No drop point therefore no melting APPLICATIONS
or leakage from lubrication points
• Used successfully with natural gas stop-cocks of main and secondary lines in
domestic equipment, instantaneous water heaters and similar equipment.
COMPOSITION • Lubrication of smaller taps made of metal, glass or plastic.
• Mineral oil
• Inorganic thickener TYPICAL PROPERTIES
• Solid lubricants Specification writers: These values are not intended for use in preparing specifications.
Please contact your local Dow Corning sales representative prior to writing specifications
on this product.
Standard* Test Unit Result
Color Black
Consistency, density, viscosity
DIN 51 818 Consistency class, NLGI¹ ca. 3
ISO 2137 Worked penetration mm/10 205-240
ISO 2811 Density at 20°C g/ml 0.96
DIN 51 562 Base oil viscosity at 40°C mm²/s 900
DIN 51 562 Base oil viscosity at 100°C mm²/s 42
Temperature
Service temperature range °C 0 to +160
short term +220
ISO 2176 Drop point °C None
Loading capacity, protection against wear
Four-ball tester
DIN 51 350 T.4 Weld load N 2100
DIN 51 350 pt.5 Wear scar under 800N load mm 0.85
Almen-Wieland machine
OK load N 14500
Frictional force with OK load N 1300
Resistance
DIN 51 807 T.1 Water resistance, static evaluation step 0-90
DIN 51 808 Oxidation resistance, pressure drop 100h, bar 1.3
99°C
Oil separation
DIN 51 817 Standard test % 0.0
1. National Lubricating Grease Institute.
* ISO: International Standardisation Organisation
DIN: Deutsche Industrie Norm
HOW TO USE means of a brush, spatula, grease-gun
How to apply or automatic lubrication device. Can
be used in central lubrication systems.
Clean the contact areas. As is usual If plastics or elastomers are present,
with lubricating greases, apply by compatibility tests for swelling and

7. shrinkage, stress-crack formation, WARRANTY
changes in strength and hardness, INFORMATION - PLEASE
should be carried out because of the
difference in their qualities. READ CAREFULLY
The information contained herein is
HANDLING PRECAUTIONS offered in good faith and is believed
to be accurate. However, because
PRODUCT SAFETY conditions and methods of use of our
INFORMATION REQUIRED FOR products are beyond our control, this
SAFE USE IS NOT INCLUDED. information should not be used in
BEFORE HANDLING, READ substitution for customer's tests to
PRODUCT AND SAFETY DATA ensure that Dow Corning's products
SHEETS AND CONTAINER are safe, effective, and fully
LABELS FOR SAFE USE, satisfactory for the intended end use.
PHYSICAL AND HEALTH Dow Corning's sole warranty is that
HAZARD INFORMATION. THE the product will meet the
SAFETY DATA SHEET IS Dow Corning sales specifications in
AVAILABLE FROM YOUR LOCAL effect at the time of shipment. Your
DOW CORNING SALES exclusive remedy for breach of such
REPRESENTATIVE. warranty is limited to refund of
purchase price or replacement of any
USABLE LIFE AND product shown to be other than as
STORAGE warranted. Dow Corning specifically
When stored at or below 20°C in the disclaims any other express or implied
original unopened containers, this warranty of fitness for a particular
product has a usable life of 60 months purpose or merchantability. Unless
from the date of production. Dow Corning provides you with a
specific, duly signed endorsement of
fitness for use, Dow Corning
PACKAGING disclaims liability for any incidental
This product is available in different or consequential damages.
standard container sizes. Detailed Suggestions of use shall not be taken
container size information should be as inducements to infringe any patent.
obtained from your nearest
Dow Corning sales office or
Dow Corning distributor.
LIMITATIONS
This product is neither tested nor
represented as suitable for medical or
pharmaceutical uses.
HEALTH AND
ENVIRONMENTAL
INFORMATION
To support customers in their product
safety needs, Dow Corning has an
extensive Product Stewardship
organization and a team of Health,
Environment and Regulatory Affairs
specialists available in each area.
For further information, please
consult your local Dow Corning
representative.
2 23/11/1998 ® MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0146B-01 DC 2941 ©1997-2001 Dow Corning Corporation. All rights reserved.

8. c
d
Product Information
Specialty
Lubricants MOLYKOTE® FS 1292
Fluoro-Silicone Grease
FEATURES
APPLICATION
" Particularly suitable for long-term " Lubricating grease for metal/metal combinations with slow to medium-fast
lubrication by virtue of its extremely low movements and medium loads over a wide temperature range.
tendency towards oxidation
" High drop point >250ºC (482ºF);
consequently reduced risk of melting and TYPICAL PROPERTIES
run-out from lubrication point Specification writers: These values are not intended for use in preparing specifications.
" Wide service temperature range, Please contact your local Dow Corning sales representative prior to writing specifications on
-40ºC to +200ºC (-40ºF to +392ºF); this product.
for short periods, up to 230ºC (446ºF)
" High resistance to water and water Standard* Test Unit Result
washout
" Resistant to mineral oil, fuels and many Color Whitish
chemicals Consistency, density, viscosity
DIN 51 818 NLGI consistency class 1-2
COMPOSITION ISO 2137 Worked penetration mm/10 280-340
" Fluorosilicone oil ISO 2811 Density at 20ºC (68ºF) g/ml 1.28
" Organic thickener DIN 51 562 Base oil viscosity at 25ºC (77ºF) mm /s2
1000
Temperature
Service temperature ºC -40 to +200 (+230
for short periods)
ºF -40 to +392 (+446
for short periods)
ISO 2176 Drop point ºC >250
ºF >482
ASTM-D147880 Low temperature torque test
at -30ºC (-22ºF)
Initial break-away torque Nm 118x10-3
Torque after 20 minutes running time Nm 41x10-3
ASTM-D147880 Low temperature torque test
at -40ºC (-40ºF)
Initial break-away torque Nm 856x10-3
Torque after 20 minutes running time Nm 56x10-3
Load-carrying capacity
Four-ball tester (VKA)
DIN 51 350 pt.4 Weld load N 3400
Oil separation
DIN 51 817 Standard test % 0.3
* ASTM: American Society for Testing and Materials.
ISO: International Standardisation Organisation.
DIN: Deutsche Industrie Norm.
HOW TO USE MOLYKOTE FS 1292 Grease can be
How to apply used in centralised lubrication systems.
Clean bearing surfaces. Apply grease Do not mix with other greases.
in the normal way using a brush, grease
gun or automatic lubricating system.

9. HANDLING PRECAUTIONS LIMITED WARRANTY
Product safety information required for INFORMATION - PLEASE
safe use is not included. Before READ CAREFULLY
handling, read product and safety data The information contained herein is
sheets and container labels for safe use, offered in good faith and is believed to
physical and health hazard information. be accurate. However, because
The material safety data sheet is conditions and methods of use of our
available on the Dow Corning website products are beyond our control, this
at www.dowcorning.com. You can also information should not be used in
obtain a copy from your local substitution for customer's tests to
Dow Corning sales representative or ensure that Dow Corning's products are
Distributor or by calling your local safe, effective, and fully satisfactory
Dow Corning Global Connection. for the intended end use. Suggestions
of use shall not be taken as
USABLE LIFE AND inducements to infringe any patent.
STORAGE
When stored at or below 20ºC (68ºF) in Dow Corning's sole warranty is that the
the original unopened containers, this product will meet the Dow Corning
product has a usable life of 60 months sales specifications in effect at the time
from the date of production. of shipment.
PACKAGING Your exclusive remedy for breach of
This product is available in different such warranty is limited to refund of
standard container sizes. Detailed purchase price or replacement of any
container size information should be product shown to be other than as
obtained from your nearest warranted.
Dow Corning sales office or
Dow Corning distributor. DOW CORNING SPECIFICALLY
DISCLAIMS ANY OTHER
LIMITATIONS EXPRESS OR IMPLIED
This product is neither tested nor WARRANTY OF FITNESS FOR A
represented as suitable for medical or PARTICULAR PURPOSE OR
pharmaceutical uses. MERCHANTABILITY.
HEALTH AND DOW CORNING DISCLAIMS
ENVIRONMENTAL LIABILITY FOR ANY
INFORMATION INCIDENTAL OR
To support Customers in their product CONSEQUENTIAL DAMAGES.
safety needs, Dow Corning has an
extensive Product Stewardship WE HELP YOU INVENT THE
organization and a team of Product FUTURE."
Safety and Regulatory Compliance
(PS&RC) specialists available in each
www.dowcorning.com
area.
For further information, please see our
website, www.dowcorning.com or
consult your local Dow Corning
representative.
MOLYKOTE FS 1292 Fluoro-Silicone Grease WE HELP YOU INVENT THE FUTURE. is a trademark of Dow Corning Corporation.
2 08/02/2002 MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0165C-01 DC 2991 ©0-2002 Dow Corning Corporation. All rights reserved.

10. c
d
Product Information
Specialty
Lubricants MOLYKOTE® 165 LT
Gearwheel grease
Gearwheel grease for the lubrication of highly stressed open
gears and reducing gears made of metal, with a peripheral speed
FEATURES of up to 2.5 m/s
" Extremely high load-carrying capacity
" Wear protection and reduction of existing APPLICATIONS
pitting in gear teeth flanks during " Open gears that are subjected to high stresses and bad weather effects.
operation, due to the solid lubricants
" Successfully used in crushing plants and in transmission gears and threaded
incorporated in the grease. Extremely
spindles of heavy, crank-driven presses.
adhesive due to build-in adhesion
improver
" Good protection against corrosion TYPICAL PROPERTIES
(corrosion index 0 when tested using the Specification writers: These values are not intended for use in preparing specifications.
SKF-Emcor method) Please contact your local Dow Corning sales representative prior to writing specifications on
" Contains no lead or nickel this product.
COMPOSITION Standard* Test Unit Result
" Mineral oil Color Black
" Lithium soap Consistency, density, viscosity
" Solid lubricants
ISO 2137 Unworked penetration mm/10 240-270
" Corrosion inhibitor
" Adhesion improver ISO 2811 Density at 20ºC (68ºF) g/ml 0.96
" EP additives DIN 51 562 Base oil viscosity at 40ºC (104ºF)1 mm2/s 320
Temperature
Service temperature range ºC -25 to +120
ºF -13 to +248
ISO 2176 Drop point ºC 175
ºF 347
ASTMD147880 Low temperature torque test at -20ºC (-4ºF)
Break-away torque Nm 880x10-3
Torque after 20 minutes running time Nm 115x10-3
DIN 51 805 Kesternich method - flow pressure at -20ºC (-4ºF) mbar 1350
Loading capacity, protection against wear, service life
Four-ball tester
DIN 51 350 T.4 Weld load N 4400
DIN 51 350 T.5 Wear scar under 800N load mm 1.2
Almen-Wieland machine
OK load N 20000
Frictional force with OK load N 2900
Corrosion protection
DIN 51 802 SKF-Emcor method
Degree of corrosion 0
Resistance
DIN 51 807 T.1 Water resistance, static evaluation step 2-90
DIN 51 808 Oxidation resistance, pressure drop 100h, bar 0.2
99ºC (210ºF)

11. TYPICAL PROPERTIES (continued)
Standard* Test Unit Result
Oil separation
DIN 51 817 Standard test % 1.2
1. Calculated viscosity value of base oil mixture.
* ASTM: American Society for Testing and Materials.
ISO: International Standardisation Organisation.
DIN: Deutsche Industrie Norm.
HOW TO USE PACKAGING LIMITED WARRANTY
How to apply This product is available in different INFORMATION - PLEASE
Carefully clean the metal surfaces and standard container sizes. Detailed READ CAREFULLY
apply using a spatula or brush. container size information should be The information contained herein is
obtained from your nearest offered in good faith and is believed to
HANDLING PRECAUTIONS Dow Corning sales office or be accurate. However, because
Product safety information required for Dow Corning distributor. conditions and methods of use of our
safe use is not included. Before products are beyond our control, this
handling, read product and safety data LIMITATIONS information should not be used in
sheets and container labels for safe use, This product is neither tested nor substitution for customer's tests to
physical and health hazard information. represented as suitable for medical or ensure that Dow Corning's products are
The material safety data sheet is pharmaceutical uses. safe, effective, and fully satisfactory
available on the Dow Corning website for the intended end use. Suggestions
at www.dowcorning.com. You can also HEALTH AND of use shall not be taken as
obtain a copy from your local ENVIRONMENTAL inducements to infringe any patent.
Dow Corning sales representative or INFORMATION
Distributor or by calling your local To support Customers in their product Dow Corning's sole warranty is that the
Dow Corning Global Connection. safety needs, Dow Corning has an product will meet the Dow Corning
extensive Product Stewardship sales specifications in effect at the time
USABLE LIFE AND organization and a team of Product of shipment.
STORAGE Safety and Regulatory Compliance
When stored at or below 20ºC (68ºF) in (PS&RC) specialists available in each Your exclusive remedy for breach of
the original unopened containers, this area. such warranty is limited to refund of
product has a usable life of 60 months purchase price or replacement of any
from the date of production. For further information, please see our product shown to be other than as
website, www.dowcorning.com or warranted.
consult your local Dow Corning
representative. DOW CORNING SPECIFICALLY
DISCLAIMS ANY OTHER
EXPRESS OR IMPLIED
WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR
MERCHANTABILITY.
DOW CORNING DISCLAIMS
LIABILITY FOR ANY
INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
WE HELP YOU INVENT THE
FUTURE."
www.dowcorning.com
MOLYKOTE 165 LT Gearwheel grease WE HELP YOU INVENT THE FUTURE. is a trademark of Dow Corning Corporation.
2 28/01/2002 MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0179C-01 DC 2939 ©1997-2002 Dow Corning Corporation. All rights reserved.

12. Product Information
High Performance
®
Lubricants Molykote 33 Extreme
Low Temperature Bearing Grease,
Molykote® 41 Extreme High
Temperature Bearing Grease,
Molykote® 44 High Temperature
Bearing Grease
FEATURES Lubricants for antifriction bearings and plastic and rubber
parts
x Resistance to oxidation, moisture and
corrosive atmospheres USES
x Inertness All three Molykote® Bearing Grease are used to lubricate ball bearings operating
x Good shear stability under light to moderate loads. These can be used for:
x Wide service temperature range: Molykote® 33 Extreme Low Temperature Bearing Grease
33 Extreme Low Temperature • Freezer cart casters and cold room conveyor equipment
Grease: -100 to 400°F (-73 to 204°C) • Utility disconnect switch contacts
41 Extreme High Temperature • Plastic electric clock motors
Grease: 0 to 550°F (-18 to 288°C) • Maximum-demand meters, power-factor meters, watt-hour meters
44 High Temperature Grease: -40 to • Windshield wiper motor gears
400°F (-40 to 204°C) • Photographic, optical and surveying equipment
x Compatible with many plastics • Oscillographs, geophysical and light, low-torque instruments
• Starter clutch drives
COMPOSITION
Molykote® 41 Extreme High Temperature Bearing Grease
x Lithium soap • Antifriction bearings of high-temperature equipment
x Phenylmethyl silicone oil • Oven conveyor bearings
• Wheel bearings of core oven carts
• Governor linkage of steam turbines
• Ball and socket connections of power insulators
Molykote® 44 High Temperature Bearing Grease
• Kiln preheater fans, oven fans, radiator cooling fans
• Textile slashers and driers
• Aircraft engine
• Conveyor systems
These greases do not soften or affect most plastics and are used to lubricate
plastic gears, bearings and cams, as well as metal and rubber parts. Because of
low torque requirements, Molykote® 33 Extreme Low Temperature Bearing
Grease is especially effective in equipment that must start in extreme cold.
Oxidation Resistance – Molykote® Bearing Greases are recommended for use in
units that must remain operable when subjected not only to low and high
operating temperatures, but also to severe weathering and oxidation.

13. TYPICAL PROPERTIES
Specification Writers: These values are not intended for use in preparing specifications. Please contact your local
Dow Corning sales office or your Global Dow Corning Connection before writing specifications on this product.
Method Test Results
33 Light 33 Medium 41 Grease 44 Light 44 Medium
Color Off White Off White Black Off White Off White
Thickner Lithium Soap Lithium Soap Carbon Black Lithium Soap Lithium Soap
Base Oil Silicone Silicone Silicone Silicone Silicone
DIN 51 562 Base Oil Viscosity @ 25°C, mm2/s 100 100 316 125 125
ASTM D 217 Penetration, worked 60 strokes, mm 320 280 280 300 280
NLGI # 1 2 2 ~1 2
DIN 51 350 pt4 4 ball weld load, N (kg) 1200 (122) 1200 (122) 1500 (152) 1100 (113) 1100 (113)
1
Max Dn Value (Bore Size in mm X rpm) 250,000 200,000 75,000 350,000 300,000
Service Temperature2 Degrees C (F) -73 to 204 -73 to 204 -18 to 288 -40 to 204 -40 to 204
(-100 to 400) (-100 to 400) (0 to 550) (-40 to 400) (-40 to 400)
ASTM D 2265 Drop Point Degrees C (F) 226 (439) 226 (439) >300 (>572) 220 (432) 220 (432)
Fed Std 791 Bleed after 24 hrs @149°C (300°F) % 2 1 4.8 3 2.5 2
DIN 51 817 Oil Separation (Standard Test, 7 days at 40°C) % 3.2 1.6 2.6 2.4 1.4
Specific Gravity @25°C (77°F) 0.97 0.97 1.14 1.05 1.05
ASTM D 1478-80 Low Temperature Torque @ -73°C
Initial Break-away Torque, Nm 130 x 10 -3 164 x 10 -3
Torque after 20 minutes running time, Nm 13 x 10 -3 22 x 10 -3
Low Temperature Torque @ -40°C
Initial Break-away Torque, Nm 225 x 10 -3 336 x 10 -3
-3
Torque after 20 minutes running time, Nm 60 x 10 124 x 10 -3
DIN 51 808 Oxidation Resistance, pressure drop 100hr,
99°C (210°F) bar (psi) 0.4 (5.80) 0 0.1 (1.45)
DIN 51 821-02-A FAG Rolling Element Bearing Tester, FE9,
1500/6000-150, F50, Hrs 110 110
1
Maximum Dn values are approximations and will vary widely with temperature, load and bearing type.
2
Estimated service temperature range based on product formulation and laboratory testing. Actual service temperature range is dependent on other factors including the specific
application environment.
3
Values are at 392°F (200°C).
Specification Writers: Please obtain copies of the Dow Corning Sales Specifications for these products and use them as a basis for your specifications. They may be
obtained from any Dow Corning Sales Office, or from Dow Corning Customer Service in Midland, MI. Call (989) 496-6000.
Figure 1. Suggested Product Temperature Range Recommendations
Limitations of Typical Organic Greases
-100°F -20°F 260°F 450°F 550°F
®
Molykote 33 Extreme Low Temperature Grease
®
Molykote 41 Extreme
High Temperature Grease
Molykote® 33 Extreme Low Temperature Bearing Grease We help you invent the future is a trademark of Dow Corning Corporation.
Molykote® 41 Extreme High Temperature Bearing Grease Molykote is a registered trademark of Dow Corning Corporation.
Molykote® 44 High Temperature Bearing Grease May 4, 2006, ® Dow Corning is a registered trademark of Dow Corning Corporation.
Ref. No. 10-814C-01 Molykote
DIC164544 44 High Temperature Grease ”2006 Dow Corning Corporation. All rights reserved.

14. DESCRIPTION combinations, especially where sliding 3.6-kg cans, 5-kg pails, 18-kg pails,
Molykote® 33 Extreme Low friction is encountered. 25-kg pails, and 180-kg drums.
Temperature Bearing Grease,
Molykote® 41 Extreme High Molykote® 41 Extreme High HANDLING PRECAUTIONS
Temperature Bearing Grease and Temperature Bearing Grease – Product safety information required for
Molykote® 44 High Temperature Bearings operating at extremely high safe use is not included. Before
Bearing Grease are silicone lubricating temperatures need to be frequently handling, read product and safety data
oils with thickeners added. monitored to ensure that the grease has sheets and container labels for safe
Molykote® 33 Extreme Low not dried out. If this occurs, more use, physical and health hazard
Temperature Bearing Grease and grease can be added, or the existing information. The material safety data
Molykote® 44 High Temperature grease rejuvenated by adding sheet is available on the Dow Corning
Bearing Grease are thickened with a Dow Corning® 710 Fluid. website at www.dowcorning.com. You
special lithium soap; Molykote® 41 can also obtain a copy from your local
Extreme High Temperature Bearing These products are neither tested nor Dow Corning sales representative or
Grease is thickened with carbon black. represented as suitable for medical or Distributor or by calling your local
pharmaceutical uses. Dow Corning Global Connection.
Molykote® 33 Extreme Low
Temperature Bearing Grease and HEALTH AND
SHIPPING LIMITATIONS
Molykote® 44 High Temperature ENVIRONMENTAL
None.
Bearing Grease are available in light INFORMATION
and medium consistencies – NLGI #1 To support Customers in their product
and #2. Molykote® 41 Extreme High USABLE LIFE AND safety needs, Dow Corning has an
Temperature Bearing Grease is STORAGE extensive Product Stewardship
available in a medium consistency – When stored at or below 90°F (32°C), organization and a team of Product
NLGI #2. Molykote® 33 Extreme Low Safety and Regulatory Compliance
Temperature Bearing Grease, (PS&RC) specialists available in each
LISTINGS/ Molykote® 41 Extreme High area.
SPECIFICATIONS Temperature Bearing Grease and
Molykote® 33 Extreme Low Molykote® 44 High Temperature For further information, please see our
Temperature Bearing Grease is USDA Bearing Grease have a shelf life of website, www.dowcorning.com or
listed for use as a lubricant where there 60 months from date of manufacture. consult your local Dow Corning
is no possibility of food contact. Refer to product packaging for “Use representative.
By” date.
HOW TO USE
Conventional grease application PACKAGING
methods – brushing, grease gun or Not all sizes available in all
automatic application – are suitable for geographies.
use with these Molykote® Bearing
Greases. Laboratory tests and field Molykote® 33 Extreme Low
reports indicate that “heavy duty” guns Temperature Bearing Grease is
available from such manufacturers as supplied in 100-g tubes, 150-g tubes,
Lincoln-St. Louis are preferred. 400-g cartridges, 1-kg cans, 3.6-kg
cans, 18-kg pails, 25-kg pails, 55-kg
Note: Extra care should be taken at all drums, and 180 kg drums.
times to prevent dirt from
contaminating the lubricant. These Molykote® 41 Extreme High
greases should be packed with a clean Temperature Bearing Grease is
metal or ebonite spatula. supplied in 100-g tubes, 150-g tubes,
400-g cartridges, 1-kg cans, 3.6-kg
LIMITATIONS cans, 5-kg pails, 18-kg pails, 25-kg
These greases should not be applied to pails, and 181.4-kg drums.
surfaces that are to be painted. These
greases should not be used with highly Molykote® 44 High Temperature
loaded ferrous metal bearing Bearing Grease is supplied in 100-g
tubes, 150-g tubes, 400-g cartridges,
Molykote® 33 Extreme Low Temperature Bearing Grease We help you invent the future is a trademark of Dow Corning Corporation.
Molykote® 41 Extreme High Temperature Bearing Grease Molykote is a registered trademark of Dow Corning Corporation.
Molykote® 44 High Temperature Bearing Grease May 4, 2006, Dow Corning is a registered trademark of Dow Corning Corporation.
Ref. No. 10-814C-01 DIC164544 ”2006 Dow Corning Corporation. All rights reserved.

15. LIMITED WARRANTY
INFORMATION - PLEASE
READ CAREFULLY
The information contained herein is
offered in good faith and is believed to
be accurate. However, because
conditions and methods of use of our
products are beyond our control, this
information should not be used in
substitution for customer's tests to
ensure that Dow Corning's products
are safe, effective, and fully
satisfactory for the intended end use.
Suggestions of use shall not be taken
as inducements to infringe any patent.
Dow Corning's sole warranty is that
the product will meet the Dow Corning
sales specifications in effect at the time
of shipment.
Your exclusive remedy for breach of
such warranty is limited to refund of
purchase price or replacement of any
product shown to be other than as
warranted.
DOW CORNING SPECIFICALLY
DISCLAIMS ANY OTHER
EXPRESS OR IMPLIED
WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE OR
MERCHANTABILITY.
DOW CORNING DISCLAIMS
LIABILITY FOR ANY
INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
We help you invent the future.™
www.dowcorning.com
Molykote® 33 Extreme Low Temperature Bearing Grease We help you invent the future is a trademark of Dow Corning Corporation.
Molykote® 41 Extreme High Temperature Bearing Grease Molykote is a registered trademark of Dow Corning Corporation.
Molykote® 44 High Temperature Bearing Grease May 4, 2006, Dow Corning is a registered trademark of Dow Corning Corporation.
Ref. No. 10-814C-01 DIC164544 ”2006 Dow Corning Corporation. All rights reserved.

16. Product Information
Silicon-Based
Compounds Dow Corning ® 340
Heat Sink Compound
FEATURES Compound provides thermal coupling of electrical/electronic
• High thermal conductivity devices to heat sinks
• Low bleed
• Stable at high temperatures USES
Dow Corning ® 340 Heat Sink Compound is applied to the base and mounting
COMPOSITION studs of transistors, diodes and silicon-controlled rectifiers. It can also serve as an
• Greaselike silicone fluid thickened effective thermal coupler for many heat sink devices where efficient cooling is
with metal oxide filler required. It is also suitable for aircraft engines where heat sink properties are
required.
This product has also been used as a high-voltage corona suppressant, nonflammable
coating in connections for flyback transformers and TV sets and similar applications.
TYPICAL PROPERTIES
Specification Writers: Please contact your local Dow Corning sales office or your Global
Dow Corning Connection before writing specifications on this product.
Method Test Unit Result
Color White
ASTM D 217 Consistency, Penetration
unworked 300
worked 60 strokes 275
worked 100,000 strokes 245
Fed. Std. 791, Bleed after 24 hr at 392°F (200°C) percent 0.05
Method 321.2
Fed. Std. 791, Evaporation after 24 hr at 392°F (200°C) percent 0.5
Method 321.2
ASTM D 2265 Drop Point °F (°C) 570 (300)
ASTM D 1475 Specific Gravity at 77°F (25°C) 2.1
CTM1 0069 Thermal Conductivity, K Factor cal/sec-cm-°C 0.0014
ASTM D 149 Dielectric Strength2 volts/mil 210
ASTM D 495 Arc Resistance seconds 165
ASTM D 150 Dielectric Constant,
at 100 Hz 5
at 100 kHz 5
ASTM D 150 Dissipation Factor,
at 100 Hz 0.01
at 100 kHz 0.02
ASTM D 1169 Volume Resistivity ohm-cm 2 x 1015
ASTM D 4049 Water Spray Off percent 1.3
1
CTMs (Corporate Test Methods) correspond to standard ASTM tests in most instances.
2
Measured using a sample thickness of 50 mils.
DESCRIPTION The compound resists changes in con-
Dow Corning 340 Heat Sink Compound sistency at temperatures up to approxi-
is a grease-like silicone material, heavily mately 350°F (177°C). In doing so, it
filled with heat conductive metal helps maintain a positive heat sink seal
oxides. This combination promotes to improve heat transfer from the
high thermal conductivity, low bleed electrical/electronic device to the heat
and high-temperature stability. sink or chassis, thereby increasing
overall efficiency of the device.

17. HANDLING PRECAUTIONS PACKAGING information should not be used in
PRODUCT SAFETY INFORMATION Dow Corning 340 Heat Sink Com- substitution for customer’s tests to
REQUIRED FOR SAFE USE IS NOT pound is available in 5-oz (142-g) ensure that Dow Corning’s products
INCLUDED IN THIS DOCUMENT. tubes, 13.5-oz (383-g) weight/ are safe, effective, and fully satisfactory
BEFORE HANDLING, READ 5.75-fl oz (170-mL) volume Semco ® for the intended end use.
PRODUCT AND MATERIAL cartridges, 20-lb (9-kg) pails, and
SAFETY DATA SHEETS AND 275-lb (124.7-kg) drums for produc- Dow Corning’s sole warranty is that
CONTAINER LABELS FOR SAFE tion lines and large scale operations. the product will meet the Dow Corning
USE, PHYSICAL AND HEALTH All weights, net. sales specifications in effect at the time
HAZARD INFORMATION. THE of shipment. Your exclusive remedy
MATERIAL SAFETY DATA SHEET LIMITATIONS for breach of such warranty is limited
IS AVAILABLE FROM YOUR to refund of purchase price or replace-
This product is neither tested nor
DOW CORNING REPRESEN- ment of any product shown to be other
represented as suitable for medical
TATIVE, OR DISTRIBUTOR, OR than as warranted. Dow Corning speci-
or pharmaceutical uses.
BY CALLING YOUR GLOBAL fically disclaims any other express or
DOW CORNING CONNECTION. implied warranty of fitness for a par-
SHIPPING LIMITATIONS ticular purpose or merchantability.
None. Unless Dow Corning provides you
USABLE LIFE AND
with a specific, duly signed endorse-
STORAGE WARRANTY INFORMATION ment of fitness for use, Dow Corning
Dow Corning 340 Heat Sink Com- The information contained herein is disclaims liability for any incidental or
pound has a shelf life of 60 months offered in good faith and is believed consequential damages. Suggestions of
from date of manufacture. Refer to to be accurate. However, because use shall not be taken as inducements
product packaging for “Use By” date. conditions and methods of use of our to infringe any patent.
products are beyond our control, this
Printed in USA Dow Corning is a registered trademark of Dow Corning Corporation.
Form No. 10-748B-01 AGP5223 ©1997, 1999, 2000 Dow Corning Corporation. All rights reserved.

18. Product Information
Specialty
Lubricants MOLYKOTE® 3400 A
Thermosetting anti-friction coating
FEATURES Thermosetting anti-friction coating for metal/metal
• Outstanding corrosion protection combinations involving slow to medium-fast movements
and medium to heavy loads
• Excellent adhesion to metal
• Low friction coefficient APPLICATIONS
• High resistance to oil and fuels • Suitable for permanent lubrication, with simultaneous corrosion protection, of
friction contacts involving high compressive stress and low speeds, and
• Prevents fretting corrosion wherever oils or greases cannot be used for technical reasons or are
• Exceptionally wide service undesirable because of the risk of soiling.
temperature range • Used successfully on hinge pins, plain bearings, cams, keyways and dentate
(-198 to +430°C) couplings on aircraft, on pins, springs and bearing surfaces of motor-car
• High abrasion resistance, brakes, moving parts of locks, switches and regulators; on special chains and
consequently long service life on all types of magnetic armature.
• High compressive strength
TYPICAL PROPERTIES
Specification writers: These values are not intended for use in preparing specifications.
COMPOSITION Please contact your local Dow Corning sales representative prior to writing specifications
• Solid lubricants on this product.
• Corrosion inhibitors Standard Test Unit Result
• Organic binders Color Grey
• Solvents Density
ISO 2811 Density at 20°C g/ml 1.2
Temperature
Service temperature °C -200 to +430
Load-carrying capacity, wear protection, service life
ASTM-D2625 Falex pressure resistance¹ N p=20000*
ASTM-D2714 LFW-1, rotating p=85000*
F=2860, N,n=72 rpm, v=7.9 min, no.of
revolutions to μ=0.1¹
LFW-1, oscillating, load 900N, p=42000*
frequency=89.5 os./min. no. of
oscillations to μ=0.08¹
1. * Surface: p = phosphatised
HOW TO USE or 1 hour at 200°C.
How to apply Diluting agent: L 13 thinners.
Carefully degrease friction surfaces
with solvent and allow solvent to
HANDLING PRECAUTIONS
evaporate completely. Stir the
anti-friction coating thoroughly and PRODUCT SAFETY
apply by spraying, dipping, painting INFORMATION REQUIRED FOR
or centrifuging (dilute with SAFE USE IS NOT INCLUDED.
MOLYKOTE® L 13 - approximately BEFORE HANDLING, READ
10-20%). The friction surfaces should PRODUCT AND SAFETY DATA
be coated as evenly and thinly as SHEETS AND CONTAINER
possible. Annealing: 2 hours at 150°C LABELS FOR SAFE USE,
PHYSICAL AND HEALTH

19. HAZARD INFORMATION. THE effect at the time of shipment. Your
SAFETY DATA SHEET IS exclusive remedy for breach of such
AVAILABLE FROM YOUR LOCAL warranty is limited to refund of
DOW CORNING SALES purchase price or replacement of any
REPRESENTATIVE. product shown to be other than as
warranted. Dow Corning specifically
USABLE LIFE AND disclaims any other express or implied
warranty of fitness for a particular
STORAGE
purpose or merchantability. Unless
When stored at or below 20°C in the Dow Corning provides you with a
original unopened containers, specific, duly signed endorsement of
MOLYKOTE 3400 A Thermosetting fitness for use, Dow Corning
Anti-Friction Coating has a usable life disclaims liability for any incidental
of 60 months from the date of or consequential damages.
production. Suggestions of use shall not be taken
as inducements to infringe any patent.
PACKAGING
This product is available in different
standard container sizes. Detailed
container size information should be
obtained from your nearest
Dow Corning sales office or
Dow Corning distributor.
LIMITATIONS
This product is neither tested nor
represented as suitable for medical or
pharmaceutical uses.
HEALTH AND
ENVIRONMENTAL
INFORMATION
To support customers in their product
safety needs, Dow Corning has an
extensive Product Stewardship
organization and a team of Health,
Environment and Regulatory Affairs
specialists available in each area.
For further information, please
consult your local Dow Corning
representative.
WARRANTY
INFORMATION - PLEASE
READ CAREFULLY
The information contained herein is
offered in good faith and is believed
to be accurate. However, because
conditions and methods of use of our
products are beyond our control, this
information should not be used in
substitution for customer's tests to
ensure that Dow Corning's products
are safe, effective, and fully
satisfactory for the intended end use.
Dow Corning's sole warranty is that
the product will meet the
Dow Corning sales specifications in
2 03/03/1998 ® MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0030A-01 DC 2995 ©1998-2001 Dow Corning Corporation. All rights reserved.

20. Product Information
MOLYKOTE® 3402 C
Anti-friction Coating
FEATURES Air-curing dry lubricant
• Excellent corrosion protection
• Excellent lubricity APPLICATIONS
• Air-curing • Excellent combination of corrosion protection and lubrication.
• Strong pressure and wear resistance • Used on main axle threads of drill hammers, spindles.
COMPOSITION TYPICAL PROPERTIES
• Solid lubricants Specification writers: These values are not intended for use in preparing specifications.
Please contact your local Dow Corning sales representative prior to writing specifications
• Organic binder on this product.
• Corrosion inhibitor Standard* Test Unit Result
• Solvent Color Grey
Physical properties
DIN 53211/3 Viscosity at 20°C or 68°F (DIN3 cup) s 47
DIN 53217/2 Density at 20°C (68°F) g/ml 1.08
CTM 0242 I Non-volatile content % 34.5
Storage life years 5
Temperature
Drying time at 20°C (68°F) minutes 15
Curing time minutes/°C 120/20
Curing time minutes/°F 120/68
Service temperature range °C -200 to +310
Service temperature range °F -328 to +590
Load-carrying capacity, wear protection, service life
ASTM-D2625 Falex load-carrying capacity¹ N s=10700
ASTM-D2714 LFW-1, rotating¹ s=45
F=2860N, n=72 minutesª¹,
v=7.9m/minutes
no. of revolutions x1000 to μ=0.1
ASTM-D2714 LFW-1, oscillating¹ s=25
F=900N, frequency=89.5osc./minutes
no. of oscillations to μ=0.08
Resistance
Radiation resistance rad 10¶
1. Surface pretreatment: s = sand blasted.
* CTM: Corporate Test Method, copies of CTMs are available on request.
ASTM: American Society for Testing and Materials.
DIN: Deutsche Industrie Norm
HOW TO USE Coating. Phosphatization or
Surface preparation sandblasting (180 grid) increases the
adhesion and service life.
First clean and degrease the surface
which will be coated with
MOLYKOTE 3402 C Anti-Friction

21. How to apply Environment and Regulatory Affairs
Stir the Anti-friction Coating specialists available in each area.
thoroughly before applying by
spraying, dipping, centrifuging or For further information, please
brushing. Recommended dry film consult your local Dow Corning
thickness: 5 to 20μm. representative.
Curing WARRANTY
120 minutes at 20°C (68°F). INFORMATION - PLEASE
READ CAREFULLY
Solubility The information contained herein is
Thinning can be carried out using offered in good faith and is believed
MOLYKOTE® L 13 Thinner. to be accurate. However, because
conditions and methods of use of our
products are beyond our control, this
HANDLING PRECAUTIONS information should not be used in
PRODUCT SAFETY substitution for customer's tests to
INFORMATION REQUIRED FOR ensure that Dow Corning's products
SAFE USE IS NOT INCLUDED. are safe, effective, and fully
BEFORE HANDLING, READ satisfactory for the intended end use.
PRODUCT AND SAFETY DATA Dow Corning's sole warranty is that
SHEETS AND CONTAINER the product will meet the
LABELS FOR SAFE USE, Dow Corning sales specifications in
PHYSICAL AND HEALTH effect at the time of shipment. Your
HAZARD INFORMATION. THE exclusive remedy for breach of such
SAFETY DATA SHEET IS warranty is limited to refund of
AVAILABLE FROM YOUR LOCAL purchase price or replacement of any
DOW CORNING SALES product shown to be other than as
REPRESENTATIVE. warranted. Dow Corning specifically
disclaims any other express or implied
USABLE LIFE AND warranty of fitness for a particular
STORAGE purpose or merchantability. Unless
Dow Corning provides you with a
When stored at or below 20°C (68°F)
specific, duly signed endorsement of
in the original unopened containers
fitness for use, Dow Corning
MOLYKOTE 3402 C Anti-friction
disclaims liability for any incidental
Coating has a usable life of 60 months
or consequential damages.
from the date of production.
Suggestions of use shall not be taken
as inducements to infringe any patent.
PACKAGING
This product is available in different
standard container sizes. Detailed
container size information should be
obtained from your nearest
Dow Corning sales office or
Dow Corning distributor.
LIMITATIONS
This product is neither tested nor
represented as suitable for medical or
pharmaceutical uses.
HEALTH AND
ENVIRONMENTAL
INFORMATION
To support customers in their product
safety needs, Dow Corning has an
extensive Product Stewardship
organization and a team of Health,
2 13/03/2000 ® MOLYKOTE is a registered trademark of Dow Corning Corporation.
Ref. no. 71-0041D-01 DC 3634 ©1997-2001 Dow Corning Corporation. All rights reserved.

22. P R O D U C T I N F O R M A T I O N
Information About DESCRIPTION Bearing tests show MOLYKOTE 3451
MOLYKOTE 3451 Chemical Resistant Chemical Resistant Bearing Grease has
MOLYKOTE® 3451 Bearing Grease and MOLYKOTE 3452 good life at varying high loads and
Chemical Resistant Chemical Resistant Valve Lubricant are speeds.
Bearing Grease and fluorosilicone oils thickened with
USES
® fluorinated polymers. These lubricants:
MOLYKOTE 3452 MOLYKOTE 3451 Chemical
Provide superior resistance to most
Chemical Resistant chemicals
Resistant Bearing Grease
Valve Lubricant MOLYKOTE 3451 Chemical Resistant
Are compatible with most gaskets, Bearing Grease is an exceptional anti-
seals and packings friction bearing lubricant especially
Resist washout by water, fuels, oils designed for applications that experience
and solvents a wide range of temperatures, loads
Type and speeds. It is particularly useful in
These greases lubricate over a wide
Fluorosilicone greases bearings exposed to harsh chemicals
temperature range. MOLYKOTE 3451
or solvents, bearings used at high
Chemical Resistant Bearing Grease has
Special Properties speeds and bearings subjected to heavy
good life at temperatures from -40 to
Chemical resistance; good load- loads. MOLYKOTE 3451 Bearing Grease
450°F (-40 to 232°C);MOLYKOTE 3452
carrying ability, effective in high can be used on:
Chemical Resistant Valve Lubricant
temperatures has a serviceable temperature range Chemical mixers
from -20 to 450°F (-29 to 232°C). Both Needle bearings in circuit breakers
Primary Uses MOLYKOTE 3451 Chemical Resistant
–MOLYKOTE® 3451 Chemical Pumps
Bearing Grease and MOLYKOTE 3452
Resistant Bearing Grease – Chemical Resistant Valve Lubricant Processing equipment
NLGI #2 resist deterioration by solvents, acids, Fuel- and solvent-handling
Exceptional antifriction chlorides and other severe chemicals equipment
lubricant for bearings exposed to as well as low-pressure steam and
Sealed-for-life bearings that must
harsh chemicals, solvents, high condensate. (See Table I.)
operate at high speeds, heavy loads,
temperatures, high speeds or
and high and low temperatures
heavy loads
– MOLYKOTE ® 3452 Chemical
Resistant Valve Lubricant –
NLGI #3
Lubricant and sealant for valves,
shafts and packings exposed to
corrosive or aggressive chemicals
or high temperatures BL17877-1
Valves protected by MOLYKOTE 3452 Chemical Resistant Valve Lubricant show no evidence of
corrosion or degradation of lubricant.

23. TYPICAL PROPERTIES
These values are not intended for use in preparing specifications.
.................................................................................................... Molykote Molykote
.................................................................................................... 3451 3452
.................................................................................................... Chemical Resistant Chemical Resistant
.................................................................................................... Bearing Grease Valve Lubricant
NLGI Consistency ...................................................................... #2 #3
Color ........................................................................................... White White
Thickener ................................................................................... Fluorinated polymers Fluorinated polymers
ASTM D 217 Penetration, worked, 60 strokes ................................................ 275 270
Viscosity of fluorosilicone oil at 100°F (38°C), SUS ................ 2295 46,000
Service Temperature Range1, °F (°C) ...................................... -40 to 450 (-40 to 232) -20 to 450 (-31 to 232)
Max. Dn Value2 .......................................................................... 200,000 75,000
Specific Gravity at 77°F (25°C) ................................................. 1.44 1.50
Fed Std 791 Bleed, at 400°F (204°C), percent .............................................. 2.7 1.2
ASTM 2265 Evaporation, at 400°F (204°C), percent ................................... 3.7 1.1
Dropping Point, °F (°C) ............................................................ >536 (>280) >570 (>300)
ASTM D 1264 Water Washout, at 175°F (80°C), percent ................................ 0.3 0.1
Fed Std 791a3 4-Ball Weld Load,Kg ................................................................... 400 400
ASTM D 1478 Low-Temperature Torque
starting, g-cm at -40°F (-40°C) ............................................... 2315
running, g-cm after 1 hr at -40°F (-40°C) ............................. 1960
1
Estimated service temperature range based on product formulation and laboratory testing. Actual service temperature range is dependent on other factors including the
specific application environment.
2
Dn value = shaft size of bearing in mm x rpm; based on estimate.
3
Method 6503.
Specification Writers: Please obtain a copy of the Dow Corning Sales Specification for this product and use it as a basis for your
specifications. It may be obtained from any Dow Corning Sales Office, or from Dow Corning Customer Service in Midland, MI.
Call (989) 496-6000.
Table I: Chemical Resistance of MOLYKOTE 3451 Chemical Resistant Bearing Grease and MOLYKOTE 3452 Chemical
Resistant Valve Lubricant
.......................................................................................................... MOLYKOTE MOLYKOTE
.......................................................................................................... 3451 3452
.......................................................................................................... Chemical Resistant Chemical Resistant Hydrocarbon
After 24 hours at 77°F (25°C)1 ................................................................................................ Bearing Grease Valve Lubricant Grease2
Diesel ................................................................................................ Good3 Good Poor
Kerosene .......................................................................................... Good Good Fair
Silicone Fluid ................................................................................... Fair Good Poor
Toluene ............................................................................................ Good Good Poor
Hexane ............................................................................................. Fair Fair Poor
Xylene .............................................................................................. Good Good Poor
Isopropanol ...................................................................................... Good Good Fair
Methanol .......................................................................................... Good Good Fair
VM&P Naphtha ............................................................................... Good Good Poor
1
Test method Federal Standard 791C-6.2.
2
A lithium-thickened petroleum grease.
3
Good no observable effect on grease [grease slightly soft; poor adhesion]; Fair grease very soft; cracked and poor adhesion; Poor grease hardened or dissolved; no
adhesion.