1. Tugas 2 praktek Konsep Routing
02 April 2013
POLITEKNIK NEGERI UJUNG PANDANG
Praktek Konsep Routing
Nurhikma
42511013
2b D4 TKJ
Teknik elektro
Dosen pembimbing :
Irmawati, ST,MT
2013

2. Tugas 2 praktek Konsep Routing
02 April 2013
Activity Topology and Instructions
In this section, the initial topology and instructions are shown for review purposes.
Topology
Network to Subnet
192.168.xx.0/24
Introduction :
In this practice Packet Tracer Skills Exam, you will:
• finish connecting the devices
• design and implement an addressing scheme to meet stated requirements
• configure, verify, and troubleshoot connectivity between all devices in the network
Addressing Table
Device
Router1
Interface
Fa0/0
Address
192.168.13.1/27
Subnet Mask
255.255.255.224
Default Gateway
n/a
Router1
Fa0/1
192.168.13.33/28
255.255.255.240
n/a
Switch1
VLAN1
192.168.13.0/24
255.255.255.0
192.168.13.1/27
PC1
NIC
192.168.13.30/27
255.255.255.224
192.168.13.1/27
PC2
NIC
192.168.13.47/28
255.255.255.240
192.168.13.33/28

3. Tugas 2 praktek Konsep Routing
02 April 2013
Note: The initial network has some errors. To aid in configuring and verifying the devices as
well troubleshooting the existing errors, use a printed version of these instructions to fill in the
missing address information in the table
during Step 2.
Step 1: Connect the Devices.
Connect the following devices using the appropriate cable:
a. Connect PC1 to Switch1.
b. Connect Switch1 to the Fa0/0 interface on RouterNamamhs.
c. Connect Switch2 to the Fa0/1 interface on RouterNamamhs.
d. Connect PC1 to the RouterNamamhs console port.
Step 2: Determine the IP Addressing Scheme.
Design an addressing scheme and fill in the Addressing Table based on the following
requirements:
a. Subnet the address space 172.16.1.0/24 to provide 30 host addresses for LAN 1 while
wasting the least amount of address space.
b. Assign the first available subnet to LAN 1.
c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on
RouterNamamhs.
d. Assign the second address in this subnet to the VLAN 1 interface on Switch1.
e. Assign the highest (last) host IP address in this subnet to PC1.
f. Using the next available subnet, further subnet it to provide 10 host addresses for
LAN2 while wasting the least amount of address space.
g. Assign the lowest (first) host address in the LAN2 subnet to the Fa0/1 interface on
RouterNamamhs.
Result :
IP
= 172.16.1.0 (10101100.00010000.00000001.00000000)
Netmask = 255.255.255.0 (11111111.11111111.11111111.00000000)

4. Tugas 2 praktek Konsep Routing
02 April 2013
Untuk 30 host terdapat biner 11110
Netmask = 11100000 (224)
Jumlah host/subnet = 255-224 = 31 host.
Subnet
First host address
Last host address
Broadcast
LAN I
172.16.1.0/24
172.16.1.1/27
172.16.1.30/27
172.16.1.32/27
LAN II
172.16.1.32/27
172.16.1.33/28
172.16.1.47/28
172.16.1.48/28
Device
Router1
Interface
Fa0/0
Address
172.16.1.1/27
Subnet Mask
255.255.255.224
Default Gateway
n/a
Router1
Fa0/1
172.16.1.33/28
255.255.255.240
n/a
Switch1
VLAN1
172.16.1.0/24
255.255.255.0
PC1
NIC
172.16.1.30/27
255.255.255.224
172.16.1.1/27
172.16.1.1/27
PC2
NIC
172.16.1.47/28
255.255.255.240
172.16.1.33/28
Step 3: Configure RouterNamamhs.
a. Configure RouterNamamhs with the following basic parameters:
⎬ The router name is RouterNamamhs.
⎬ The privileged EXEC mode uses the following encrypted password: class

5. Tugas 2 praktek Konsep Routing
02 April 2013
⎬ Enable Telnet and console line login using the following password: cisco
⎬ Configure the banner message-of-the-day as Authorized access only!
b. Configure the two Fast Ethernet interfaces, including addressing and a description.
c.
Close the terminal window after completing the router configuration.
Step 4: Configure Switch1 and Verify Connectivity.
a. Remove the console connection between PC1 and RouterNamamhs.
b. Connect PC1 to the Switch1 console port.
c. Configure Switch1 with the following basic parameters:
⎬ The switch name is Switch1

6. Tugas 2 praktek Konsep Routing
02 April 2013
⎬ The privileged EXEC mode uses the following encrypted password: class
⎬ Enable Telnet and console line login using the following password: cisco
⎬ Configure the banner message-of-the-day as Authorized access only!
d. Configure interface VLAN 1 and default gateway for Switch1.
e.
Switch1 should be able to ping the default gateway.
Step 5: Configure and Verify PC1 Addressing.
a. Using the IP addressing you determined in Step 2, configure PC1 with the correct
addressing.
b. PC1 should be able to ping the default gateway.

7. Tugas 2 praktek Konsep Routing
02 April 2013
Step 6: Verify and Troubleshoot End-to-End Connectivity.
Verify that PC1 is able to ping PC2. If the ping fails, locate and correct any errors. For
example, make sure PC2 is configured correctly with appropriate addressing for the
subnet it belongs to.