3. SUMARY
1) Security and comfort
2) Instruments and controls
3) Instruction for operating
4) Service and maintenance
4. SECURITY AND CONFORT
Motorcycles are two-wheeled vehicles. Safety of its use and
operation depends on proper driving techniques, as well as the skill
of the driver conductor. All requirements should be knew by the
driver before driving a motorcycle.
complete instructions from a competent source on all aspects
of motorcycle
observe the warnings and maintenance and requirements
contained in the manual
obtain qualified information on safe driving techniques and
appropriate
get professional technical service according to the manual or
when conditions so require
Mechanical
5. SHASIS: the chassis meets two basic types of functions
Static = CHASSIS must support the weight of the rider and
passenger of motorcycle, the engine and transmission and devices
such as oil and gas.
Dynamics: the CHASSIS and the rest of the bike (wheels and
suspension) together must provide precise steering, good handling
and good grip comfort
SUSPENCION: basically a suspension has two main functions: to
keep the wheels in contact with the ground at all the time. ensure
that the parts on the bike are anchored to the wheels and fixed all
parts to it.
6. BRAKES: It works
by decreasing the speed of the vehicle by means of friction
between two or more pieces that are usually steel and shims or
synthetic or metallic pads
INSTRUMENTS AND CONTROL AND INSTRUMENTS FOR
OPERATING
TACHOMETER
Switch 'locking main direction controls the ignition and lighting
systems, and is used to lock the steering. Below describes the
following different positions
Open: All electrical circuits are energized
Closed: All electrical systems are off you can remove the key
7. closed lock: The steering is locked, and all electrical systems
are off
Indicator light beam. This warning light is turned on, when
the high beam of the lamp is on.
Shift indicator light: This indicator light flashes when the
turn signal switch pushed to the left or right.
neutral spot light this light comes on when the transmission
Is in neutral position.
The electric tachometer allows the rider to monitor engine rpm and
keep them within the power range to turn the key in the position
"on" the tachometer sweep once across the rpm range and then
returns to 0 rpm to test entire electrical circuit
the multifunction display is provided by elements following
models:
a speedometer
an odometer
fuel meter
Switch, turn signal: to signal a right turn puts the switch in this
position, to signal a left turn, push the switch to that position.
Step light switch: press this switch to make light work of passage.
8. Light switch crossing road: this interrupter position to put up the
beam and put down for beam
Horn switch: Press this switch to sound the horn
SERVICE AND MANTENANCE
FUEL LINES: check if the fuel hoses for cracks
PLUG: Check condition, clean and adjust tolerance
AIR FILTER: cleaning, change
BATTERY: check the output voltage, check the electrolyte
CLUTCH: verify operation adjust, lubricate the lever
FRONT BRAKE: check function, fluid level and leaks, changing
brake pads.
REAR BRAKE: Check operation of the brake pads, check for
damaged
Brake hose: replace if necessary
WHEELS: Check run out and for damage.
TIRES: check tread depth and are not cracks. Change if necessary,
check the air pressure.
PADS WHEEL: check whether the cushions are loose or damaged
Swing arm: Check operation and change the clearance is excessive
grease lubricated bushings.
CHAIN DRIVE: check clearance alignment and adjustment status
and lubricate chain with a chain lubricant.
9. PADS ADDRESS: check clearance cushions and steering for tough
grease lubricated.
FRAME MOUNTING: check that all bolts are properly tightened
nuts.
SIDESTAND CENTRAL: Check operation and lubricate.
FRONT FORK: Check operation and for oil leakage.
SHOCK SET: Check operation and for oil leakage.
MOTOR OIL: Change oil level and check for leaks.
ENGINE OIL FILTER: change.
MOBILE PARTS AND CABLES: lubricate.
BOX throttles grip and cable: Check operation and free play,
adjust the clearance of the cable if necessary.
SIDESTAND CENTRAL: check if the air shutoff valve, the reed
valve and the air tube change damaged parts are damaged.
FRONT FORK: check operation, adjust the headlight.