The document provides instructions for maintenance and repair of various vehicle systems. It includes sections on air bags, electronically assisted steering, rear brakes with ABS, the smart key system, power window security features, engine oil changes, and maintenance of brake tablets and discs. Procedures are outlined for inspecting or replacing components as needed.
3. INDEX
Security and comfort
• Air bags
• electronically assisted steering
Instruments and controls
Intructions and operating
Service and maintenance
5. *if the front airbag is deployed after
colicion, change the following items.
*srscm
*deployed airbag
*Seatbelt pretensioners
*front sensors inpacto
*Wiring harnesses srs
*see if the connection has been spiraling due
to heat damage
7. Clearance Inspection flywheel.
* Turn the steering wheel so that the front wheel
straight ahead and
* measure the distance to the steering wheel
that can girarce without moving the front
wheels.
* If the clearance exceeds the standard value,
check the column shaft and steering
transmissions
9. * mount the inner casing of the door front
quadrant
* Disconnect the electrical door mirror of cable
maso
* Battery voltage applied to each terminal as
shown in the table and make sure the mirror is
working properly.
11. 1 .Remove the rear wheel and tire.
2. Remove the sensor fixing bolt of the rear
wheel speed (A).
3. Remove the rear seatback.
(See Body group - "Seat")
4. Remove the trim of the rear wheel
housing.
(See Body group - "interior trim")
5. Disconnect the speed sensor on the rear
wheel.
6.For installation, follow the reverse order
13. The SMART KEY system is a system that allows
users to access and operate a vehicle in a very
appropriate way. To access the vehicle, it is not
necessary nor traditional key or the remote control.
The user wears a SMART REMOTE that requires no
conscious action by the user (for example, press the
RKE). The system is activated SMART KEY pressed a
button on the door handle.
Upon activation, the vehicle sends a request to a
limited distance. If the SMART REMOTE receives
the request, automatically sends a response to the
vehicle. Then, the system decides whether to
perform a particular action (lock, unlock ...) or remain
inactive.
Again, you need a communication between the vehicle
and the SMART REMOTE before carrying out any
action.
15. when the switch is activated the power
window auto up all doors (front, rear), the
safety function is activated.
1. Condition of the safety function Upon
detecting the strength of 100 N during
lifting of the window, the window will
decrease.
2. Inversion length of the window (except
when holding the automatic raising switch)
A. When an obstruction is detected during
the 4 mm ~ 250 mm from the top of the
door.
The window lowered to 300mm reaching the
top of the door.
17. 1. Drain the engine oil.
(a) Remove the oil filler cap.
(b) Remove the oil drain plug and drain the oil into a
container.
2. Change the oil filter.
(a) Remove the oil filter.
(b)Check and clean the mounting surface of the oil
filter.
(c)Check the part number of the new oil filter is the
same as the old.
(d)Apply clean engine oil to the gasket of a new oil
filter.
(e)Screw lightly oil filter in place, and tighten until the
gasket contacts the seat.
(f)Apply the torque below.
19. 1. Remove the front wheels and tires.
2. Loosen the hose and anchor bolts securing the
caliper then remove the front caliper assembly
3. Remove the front brake disc screws loosening
4. If wear exceeds the limit, replace the disc pads
and both the left and right sides of the vehicle.
Checking the brake pad
1. Check the pad wear. Measure the thickness of the
pad and replace if less than the prescribed value.
Thickness of tablet
Standard value: 11 mm (0.433 in.)
Service Limit: 2.0 mm (0.0787 in.).
2. Check for damage to the pad, the back metal and
grease contamination.
Checking wear of front brake disc
1. Place a graduated gauge of about 5mm (0.2 inch) at
the outer circumference of the brake disc and disc
wear measuring.