Oracle rman

1. PREPARED BY RAVI KUMAR LANKE Page 1
Oracle RMAN
One (if not the, most important) jobs of the Oracle DBA is to ensure that the databases in
their care are protected. Databases, or data in the database, can be lost through a variety of
ways including:
* User error
* Hardware failure
* Software failure
* Disasters
* Application errors
To protect your database, you will need to know how to back it up and you will need to
know how to recover your database. Backup and recovery is what this last chapter is all
about. Backup and recovery can be a very difficult and complex topic, for there are a
number of different options for you to choose from when it comes to backing up a
database. In this chapter, we aim to set you on the right course, showing you how to
perform basic database backup and recovery operations.
In this chapter we will use the Oracle RMAN tool. It comes with the Oracle RDBMS and
it’s free. In this chapter we will cover:
* Backing up your database with RMAN
* Restoring your database with RMAN
So, without further delay, let’s get started on getting your database backed up.
Backup Your Database with RMAN
Database backups with RMAN are actually quite easy. Your database can be in one of two
modes, ARCHIVELOG or NOARCHIVELOG mode. The mode your database is in
determines what kinds of backups you can perform on your database. In this section we
will cover the following topics:
Starting RMAN
The RMAN client is started from the operating system prompt. To use RMAN, simply set
the Oracle environment as you would before you use any other Oracle client (like
SQL*Plus). Once the environment is set, then you start RMAN as seen in this example:

2. PREPARED BY RAVI KUMAR LANKE Page 2
rman target=/
Once you have started RMAN you will find yourself at the RMAN prompt. We are then
ready to begin our database backup.
Perform an Offline (Cold) Backup of your Database with RMAN
In this section we will show you how to perform an offline (or cold) backup using RMAN.
This will require that the database be down (that’s why it’s called an offline backup).
Oracle supports online backups also, and we will be covering these shortly.
Before we can use RMAN we need to configure a few settings. In this section we will look at
configuring the database for our backup, and then we will proceed to do the backup.
Configure Oracle and RMAN for Backup
Before we can use RMAN we will need to configure a few settings. In this section we will
assume:
1. That you will be backing up to a file system called /u01/app/oracle/backup. You will need
to create this file system if it does not already exist.
2. That you are using an SPFILE.
Note that if you created your database as we described earlier in the book, you should
already be using an SPFILE.
The configuration is pretty basic. First, we need to configure a couple of database
parameters. These parameters will configure the Flash Recovery Area of the database.
This is the location that all the disk backups will be made to. To configure the flash
recovery area we will use the alter system command to set the value of two database
parameters:
* db_recovery_file_dest – Determines the location of the flash recovery area.
* db_recovery_file_dest_size – Determines how much space can be used by Oracle in the
flash recovery area.
We will configure the flash recovery area to the value of /u01/app/oracle/backup, and we
will assign it a 2 Gigabyte limit. Note! Oracle flash recovery area re-named to fast
recovery area
You may need to assign your flash recovery area more space depending on the following
factors:

3. PREPARED BY RAVI KUMAR LANKE Page 3
* The size of your database
* The number of backups you want to keep
* If you are running your database in ARCHIVELOG mode (which we will discuss later in
this chapter).
Here is an example of configuring the flash recovery area for the settlings listed previously.
This assumes your database is using a SPFILE which we discussed in earlier chapters:
Alter system set db_recovery_file_dest=’/u01/app/oracle/backup’;
Alter system set db_recovery_file_dest_size=2G;
We will also want to set a couple of RMAN settings before we do our first backup. Start
RMAN as detailed earlier in this section with:
$ rman target /
Now, we want to configure the following:
* Automatic backups of the control file and SPFILE.
* Retention policy to a redundancy of 2
Next, we can use the RMAN configure command to configure these settings as seen in this
example:
-- Configure the retention policy to redundancy of 2.
-- This means RMAN will try to keep 2 copies of the database
backups.
RMAN> configure retention policy to redundancy 2;
-- Configure automated backups of the control file and SPFILE.
RMAN>configure controlfile autobackup on;
Now that RMAN and the database are configured, we are ready to proceed to backup the
database.